Black & Decker BDOH200C, BDOH200 User Manual

PLEASE READ AND SAVE THIS USE AND CARE BOOK. POR FAVOR LEA ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. VEUILLEZ LIRE ET CONSERVER CE GUIDE D’ENTRETIEN ET D’UTILISATION.

Digital 9-fin oil-filled heater

Calentador de aceite con 9 aletas y digital

Radiateur à l’huile, à 9 ailettes et à affichage numérique

Models/Modelos/Modèles

BDOH200 , BDOH200C

USA/Canada 1-800-231-9786 Mexico 01-800-714-2503

www.blackanddecker.com

Accessories/Parts

(USA/Canada) 1-800-738-0245

Accesorios/Partes

(EE.UU/Canadá)

Accessoires/Pièces (É.-U./Canada)

BDOH200.Pub179200RV2 5/18/05 9:11 AM Page 1

WARNING: To reduce the risk of fire:

❑

Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front, sides and rear of heater when the heater is plugged in.

❑

Do not place heater near a bed, because objects such as pillows or blankets can fall off the bed and be ignited by heater.

❑

Always unplug from electrical outlet whenever heater is not in use.

❑

Avoid the use of an extension cord because it may overheat and cause a risk of fire. However, if an extension cord must be used, it shall be of a minimum size of 14 AWG and rated not less than 1875 watts.

CAUTION: Risk of fire - Do not operate without casters attached. When using any electrical appliance, basic precautions should always be

followed to reduce the risk of fire, electrical shock, and injury to persons including the following:

❑

Read all instructions before using heater.

❑

Heater is hot when in use. To avoid burns, do not let bare skin touch hot surface. Unplug and let heater cool down for at least ten (10) minutes before moving it. Use handles provided.

❑

Extreme caution is necessary when any heater is used by or near children or invalids, and whenever heater is left operating and unattended.

❑

Do not operate any heater with a damaged cord or plug or after it malfunctions or is dropped or damaged in any manner. Return heater to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment. Or call appropriate toll-free number listed on the cover of this manual.

❑

Do not use outdoors.

❑

Heater is not intended for use in wet or moist locations such as bathrooms, laundry areas or similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.

❑

Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic areas, and where it will not be tripped over.

❑

To disconnect heater, press OFF button, then remove plug from outlet by pulling the plug, not the cord.

❑

Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock or fire, or damage the heater.

IMPORTANT SAFETY

INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

❑

A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.

❑

Use heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.

❑

Avoid using heater when sleeping.

❑

To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surface, like bed, where openings may become blocked.

POLARIZED PLUG

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

TAMPER-RESISTANT SCREW

This unit is equipped with tamper-resistant screws. To reduce the risk of shock, do not attempt to remove the front or back housing. There are no user serviceable parts inside. Repair should be done only by authorized service personnel.

SPECIAL ATTENTION:

The use of an extension cord is not recommended. However, if it is absolutely necessary, be sure that the cord is (1) No. 14 AWG minimum size and rated no less than 1875 watts; (2) UL Listed; (3) as short as possible (long cords can overheat, as well as trip circuit breakers); (4) not used for operating more than one appliance at a time.

Note: If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

BDOH200.Pub179200RV2 5/18/05 9:11 AM Page 2

How to Use

This appliance is intended for household use only.

Important: For warranty verification, please do not remove line cord sticker. Note: This heater is packed with two caster assemblies that must be installed between the

radiator fins at each end of base pipe to make unit portable and operable. Do not use heater in any other orientation other than upright as shown in this manual.

To assemble:

1. Be sure heater is unplugged and off.

2. Keep cord out of way by winding it around cord wrap.

3. Turn heater upside down and place the two metal U-shaped screws over base pipe, between the radiator fins on either end of heater, so the screw threads extend beyond the pipe.

4. Position assembly bracket so the two slots on the bracket line up with the two screws on end of heater.

5. Set each assembly bracket over threaded end of each U-shaped screw and fasten them securely in place with wing nuts (A).

6. Set heater right side up.

The Advanced Safety Technology™ (AST) system features unique technology built into your heater that offers protection detailed in the "Special Features" section.

Important: Portable electric heaters are designed for space heating or as a supplementary heat source. They are not intended to be a main source of heat. Do not use heater as an integral part of any life support or equipment protection system, where a functional failure or misapplication of heater could jeopardize the people or things being protected. Do not touch or attempt to move heater when it is plugged in.

Always unplug and allow heater to cool before handling. Never pull unit by cord — use handle. During the first few minutes of initial use, you may notice a slight odor. This is normal and will quickly disappear.

Use heater only on floor. It radiates heat in all directions. Always leave ample space around it so it’s not too close to a wall.

1. You don't have to set the clock before using heater. Plug heater into a standard AC outlet.

Caution: Be sure that no other appliances are plugged into same circuit with heater as a circuit overload could occur.

2. Press ON/OFF button to activate heater. The red lights by POWER and TEMP SETTING buttons will turn on (B).

3. Press POWER button to select appropriate setting: LO for a small (approx. 10’x10’/3m x 3m), MED for a medium (approx. 12’x12’/3.8m x 3.8m), or HI for a large room (approx. 12’x 16’/3.8m x 5m).

4. Press TEMP SETTING button to MAX. Once desired room temperature is achieved, lower temperature setting. Leave temperature control at this position since heater will automatically cycle on and off to maintain your chosen room temperature.

5. This heater will continue to operate as long as one of the 3 red lights next to POWER button is illuminated. Be sure to press ON/OFF button to turn heater off when finished.

Note: Oil in unit is permanently sealed. You do not need to refill it.

To set clock for current time of day:

1. Plug heater in. The digital clock will flash 12:00 AM until correct time is set.

2. Press FUNCTION button until clock light and hour LED start flashing.

3. Set hour by pressing down ( ) or up ( ) arrow buttons. (If setting for PM time, make sure PM light is on.) Press FUNCTION button again to set. The minute LED will start flashing.

Product may vary slightly from what is illustrated.

1. Fins †2. Casters (Part #178451-00) †3. Assembly Bracket (Part #178453-00)

4. Cord Wrap

5. Vents

6. Handle

7. Digital control panel †8.Wing Nuts (Part #178452-00) †9. U-Shaped Screw (Part #178454-00)

10. Base Pipe

† Consumer replaceable





















Digital Display

Function button

Temperature button

On/Off button

Power button

Timer I

Clock

Timer II

BDOH200.Pub179200RV2 5/18/05 9:11 AM Page 4

4. Set minutes by pressing the down ( ) or up ( ) arrow buttons. Press FUNCTION button again to set.

Note: If heater is unplugged at any time, clock must be reset. To set timer:

This heater has two automatic timers that enable it to turn on and off automatically during two time periods within 24 hours. You may set one or both timers depending on your preference. Once set, heater will operate only at the times chosen.

To set TIMER I/ TIMER II:

1. Press ON/OFF button to turn heater on. The red lights by the POWER and TEMP SETTING buttons will turn on.

2. Press FUNCTION button (several times if needed) until both TIMER I or Timer II (if desired) and ON TIME lights start flashing.

3. Set hour and minutes by pressing down ( ) or up ( ) arrow buttons. Then press FUNCTION button again to set.

4. Press FUNCTION button until both TIMER I or Timer II (if desired) and OFF TIME lights start flashing.

5. Set hour by pressing the down ( ) or up ( ) arrow buttons until the hour is displayed. Then press FUNCTION button again. The minute LED will start flashing. Set minutes by pressing the down ( ) or up ( ) arrow buttons until minutes are displayed. Press FUNCTION button again to set.

Once one or both timers are set, heater will cycle on and off continuously at the times you set until the timers are turned off, or power is turned off. When a timer is set, the green timer light will remain on. Then, as heater turns on during the set ON TIME chosen, the green light will turn red, indicating heater is on. The light will revert back to green when heater turns off after it reaches the set OFF TIME.

To turn off the timers:

You can turn off either or both timers. To turn off Timer I, set ON TIME and OFF TIME to 00:00. To turn off Timer II, set ON TIME and OFF TIME to 00:00.

Special features and the (AST) Advanced Safety Technology™ system

1. This unit has a safety thermostat. If unit experiences excessive heat, thermostat will shut off unit. If this happens turn power off immediately. Be sure that the fins are not blocked and nothing is restricting heater. Let it cool down, and wait 10 minutes before plugging it back in to operate. If unit fails to operate after 10 minutes, it may mean that heater has internal damage and will need service or replacement.

2. A built-in tip-over switch will cut power if unit is accidentally knocked over with fins down in either direction. To reset, stand heater upright and wait a few seconds for it to begin operating again.

Care and Cleaning

This product contains no user serviceable parts. Refer service to qualified service personnel.

1. Be sure heat control is in OFF position before unplugging. Always unplug heater and allow it to cool thoroughly before attempting to clean.

2. Remove accumulated dust from heater surfaces with a soft cloth. You may use a cloth or sponge moistened with a mild detergent and water. Dry heater casing thoroughly with a soft, dry cloth before operating again. Do not immerse heater in water.

3. Coil the cord around the cord wrap at side of unit and store heater in a dry area.

INSTRUCCIONES IMPORTANTES

DE SEGURIDAD

ADVERTENCIA: Para reducir el riesgo de incendio:

❑

A fin de reducir el riesgo de incendio, cuando el calentador se encuentre enchufado, mantenga todo material combustible incluyendo los muebles, las almohadas, la ropa de cama, ropa, cortinas y papeles por lo menos a 0,9 m (3 pies) de distancia del frente, de los costados y de la parte trasera del calentador.

❑

No coloque el calentador cerca de las camas; las almohadas o las cobijas podrían caerse de la cama e incendiarse al entrar en contacto con el calentador.

❑

Siempre desconecte el calentador de la toma de corriente cuando éste no se encuentre en funcionamiento.

❑

Evite el uso de un cable de extensión porque éste se puede sobrecalentar y ocasionar el riesgo de un incendio. Si no tiene otra alternativa, utilice un cable de extensión con capacidad mínima de 14 AWG y de calificación no menor de 1875 watts.

PRECAUCIÓN: Riesgo de incendio - No utilice este aparato sin antes haber instalado los rodillos.

A fin de reducir el riesgo de un incendio, choque eléctrico o lesiones a las personas, cuando se utilizan aparatos eléctricos, siempre se debe respetar ciertas medidas de seguridad incluyendo las siguientes:

❑

Por favor lea todas las instrucciones antes de utilizar este calentador.

❑

El calentador permanece caliente mientras está en funcionamiento. A fin de evitar quemaduras, no permita que la piel entre en contacto con las superficies calientes. Desconecte y espere que el calentador se enfríe por lo menos diez (10) minutos antes de transportarlo de un lugar a otro. Utilice los mangos provistos.

❑

Se debe de tener mucho cuidado cuando un calentador se utiliza por o en la presencia de los menores de edad o de las personas minusválidas. No desatienda el aparato mientras éste se encuentre en funcionamiento.

❑

No utilice ningún calentador si el cable o el enchufe presentan cualquier desperfecto, si el aparato no funciona bien, si lo ha dejado caer o dañado. Devuelva el calentador a un centro de servicio autorizado para que lo examinen, reparen o arreglen. También puede llamar gratis al número apropiado que aparece en la cubierta de este manual.

❑

No utilice este aparato a la intemperie.

❑

Este calentador no ha sido diseñado para uso en los baños, en los cuartos de lavandería ni en las áreas interiores semejantes. Jamás coloque el calentador donde pueda caer adentro de una bañera u otro recipiente con agua.

BDOH200.Pub179200RV2 5/18/05 9:11 AM Page 6

+ 9 hidden pages