Black & Decker 97301 User Manual
IMPORTANT INFORMATION
--------------------------
Grounding
Your Drill has a grounding system to protect you from electric shock if
some damage should occur to the wiring of the tool. This system utilizes
the Drill's approved 3-conductor power cord and 3-prong grounding type
attachment plug, which should be used with the proper grounding type
receptacle, in accordance, with the National Electric Code, Canadian
Electrical Code, and Underwriters' Laboratories specifications.
GROUNDED OUTLET BOX
^ADAPTER
GROUNDING
PRONG IS
LONGEST OF
THE 3 PRONGS
i • I 1
GROUNDED
OUTLET BOX-
^^WIRE
green
GROUNDING
fl
if your unit requires less than 150 volts it has a plug that looks like Fig.
“A". It will fit directly into the proper type of 3-wire grounding receptacle.
The unit is then grounded automatically each time it is plugged in.
Shown in Fig. “B” is a special grounding adapter (not allowed in Canada
by the Canadian Electrical Code) which is available from your dealer and
will permit using a 2-wire receptacle. The green grounding wire extending
from the side of the adapter must be connected to a Permanent Ground.
If the unit requires from 150 to 250 volts, it has a plug like Fig. “C”.
No adapter is available and the plug must be used in the proper 3-wire
grounding receptacle.
We recommend that you NEVER disassemble the tool or try to do any
rewiring in the electrical system. Any such repairs should be performed
only by B&D Service Centers or other qualified service organizations.
Should you be determined to make a repair yourself, remember that the
green colored wire is the “grounding" wire. Never connect this green
wire to a “live" terminal. If you replace the plug on the power cord, be
sure to connect the green wire only to the grounding (longest) prong on
a 3-prong plug.
If you use an extension cord, be sure that it Is a 3-conductor, grounding
type cord. Grounding must be continuous from the tool plug to the
grounded receptacle.
Turn collar to open chuck jaws. Place
bit in chuck so that end rests on
chuck bottom. Tighten chuck collar
by hand. Place chuck key in each of
the three holes, and tighten In clock
wise direction. It's important to
tighten chuck with all three holes. To
release bit, turn chuck key counter
clockwise in just one hole, then
loosen chuck by hand.
To remove the chuck from the Drill,
for using a threaded shank accessory
or for chuck replacement, first un
plug the tool. Open the chuck and
remove screw in bottom of chuck
(left hand thread). Insert the key in
the chuck and tap it sharply in the
direction the tool normally rotates -see at left. This will loosen the chuck
shank threads and the chuck may be
unscrewed by hand.
GROUNDED OUTLET B0X.„
0
€)
/
GROUNDING
PRONG IS
LONGEST OF
THE 3 PRONGS
C
Extension Cord
When using this drill at a considerable distance from power source,
a 3-conductor, grounding-type extension cord of adequate size must be
used for safety, and to prevent loss of power and over-heating. For a
120-volt tool, the minimum size of the wires in any extension cord up
to 75 feet long must be 18-gauge (American Wire Gauge). If the total
extension cord length is from 75 to 100 feet, 16-gauge wire is required
throughout the extension. 200-volt tools require a minimum wire size of
only 18-gauge in extension cord lengths up to 200 feet long. (NOTE:
16-gauge wire is heavier than 18-gauge wire and will carry current for
longer distances without a voltage drop.)
P.T.I. Safety Rule #12 applies to Extension Cords as well as the Tool
Power Cord. Before using cords, inspect them for loose or exposed wires
and damaged insulation. Make any needed repairs or replacement before
using your power tool.
MAINTENANCE
....................................................
If The Tool Does Not Run
First, check your electric outlet by plugging in another tool or lamp.
If either of these' doesn't work, check for blown fuses. If current is
present, check plugs and sockets for tight connections. If the tool still
won’t run, take or send it to a Black & Decker Service Center for checking
and repair. Do not attempt any major repair on your own.
Lubrication
Self lubricating bearings are used in the tool and periodic relubrication
is not required. However, it is recommended that, at least once a year,
you take or send the tool to a B&D Service Center for a thorough
cleaning, inspection and lubrication of the gear case.
Cleaning
UNPLUG DRILL. Use a rag dampened only with mild soap and hot water.
Many household cleaners contain chemicals which could seriously
damage the plastic handle. DO NOT let any water get inside the tool.
Guarantee
Black & Decker guarantees, for one year from date of purchase, to
correct by repair or parts replacement without charge any defect due to
faulty material or v^orkmanship. Simply return the complete unit,
transportation prepaid, to any Black k. Decker Service Center or
Authorized Service Station. Naturally, we assume no responsibility for
damage caused by misuse, careless handling or where repairs have
been made or attempted by others. No other guarantee, written or
verbal, is authorized by us.
Important!
To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by BLACK & DECKER Service Centers
or other qualified service organizations, always using Black & Decker
replacement parts.
» # # I
SM'Tools-Electric
—Yellow Pages—
for Service I Sales
I ® ® (
THE BLACK & DECKER MFC. CO.
Towson, Md. 21204, U.S.A.
' ® ® ® ® ® (
Form No. 97301
..
(C3-AL) Printed in U.S.A.
Black & Decker.
OWNER’S MANUAL
Your new Black & Decker
Drill is an outstanding
value, combining quality
construction, excellent per
formance and versatility.
Its special operating fea
tures are speed control and
a switch to reverse the di
rection of motor rotation.
Not only will it DRILL holes
in practically any material,
but with optional acces
sories it can SAND, POLISH,
BUFF, DRIVE SCREWS,
GRIND, DRIVE HOLE SAWS,
MIX PAINT, PUMP WATER
and REMOVE rust and old
paint.
For personal safety and for
proper operation of the
Drill, please take the time
mm
liii i
VARIABLE
TRIGGER SWITCH
SPEED.
SWITCH
LOCKING
BUTTON
VARIABLE SPEED REVERSING DRILLS
1/4" DRILL
Capacity: dia. holes in steel;
Y2" dia. in hardwood. 120 Volts
A.C. 2.0 Amps. 1/6 H.P. 2250
R.P.M.
Capacity: %" dia. holes in steel;
%" dia. in hardwood. 120 Volts
A.C. 2.4 Amps. 1/6 H.P. 1000
R.P.M.
to carefully read all of the
safety rules and instruc
tions in this booklet. Don't
forget to send in the guar
antee registration card.
THANK YOU for buying
BLACK & DECKER!
3/8" DRILL
IMPORTANT INFORMATION
Safety Rules for Power Tools
The use of the Safety Seal of the Power Tool Institute assures you that
this tool is produced and tested in accordance with applicable national
safety standards. Operational safety, however, depends to a great extent
upon the user of the tool. Please pay close attention to the following
rules.
1. KNOW YOUR POWER TOOL — Read owner's manual carefully. Learn
its applications and limitations as well as the specific potential
hazards peculiar to this tool.
2. GROUND ALL TOOLS - UNLESS DOUBLE-INSULATED. If tool is
equipped with three-prong plug, it should be plugged into a threehole electrical receptacle. If adapter is used to accommodate twoprong receptacle, the adapter wire must be attached to
ground. Never remove third prong.
3. KEEP GUARDS IN PLACE and in working order.
4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite
accidents.
5. AVOID DANGEROUS ENVIRONMENT. Don't use power tool in damp
or wet locations. And keep work area well lit.
6. KEEP CHILDREN AWAY. All visitors should be kept safe distance
from work area.
7. STORE IDLE TOOLS. When not in use, tools should be stored in
dry, high or locked-up place — out of reach of children.
8. DON'T FORCE TOOL. It will do the job better and safer at the rate
for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or attachment to do the
job of a heavy duty tool.
10. WEAR PROPER APPAREL. No loose clothing or jewelry to get caught
in moving parts. Rubber gloves and footwear are recommended
when working outdoors.
11. USE SAFETY GLASSES with most tools. Also face or dust mask if
cutting operation is dusty.
12. DON'T ABUSE CORD. Never carry tool by cord or yank it to dis
connect from receptacle. Keep cord from heat, oil and sharp edges.
13. SECURE WORK. Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate tool.
14. DON'T OVERREACH. Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and
clean for best and safest performance. Follow instructions for
lubricating and changing accessories.
16. DISCONNECT TOOLS. When not in use, before servicing; when
changing accessories such as blades, bits, cutters, etc.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of check
ing to see that keys and adjusting wrenches are removed from
tool before turning it on.
18. AVOID ACCIDENTAL STARTING. Don't carry plugged-in tool with
finger on switch.
a known
OPERATION
--------
------ ^------
------ ------ -
------ —
-------
-
Switches
The Variable Speed Trigger Switch permits "FREE HAND" speed control — the farther the
trigger is depressed, the higher the speed of the Drill. A Switch Locking Button permits
locking the trigger in the full "ON" position for continuous operation. To lock the trigger
"ON" depress trigger fully and push in locking button, then gently release trigger. To
release locking mechanism, depress trigger fully, then release It. Trigger can also be locked
"ON" in a position which gives less than full speed. Do not lock trigger "ON" for hand-held
drilling, so that you can release trigger instantly if bit binds in hole.
NOTE: Use lower speeds for STARTING HOLES WITHOUT A CENTER PUNCH, DRILLING IN
METAL OR PLASTICS, DRIVING SCREWS, DRILLING CERAMICS, OR MIXING PAINT. Higher
speeds are better for DRILLING WOOD AND COMPOSITION BOARDS, AND FOR USING
ABRASIVE AND POLISHING ACCESSORIES.
The Reversing Switch is a slide switch located in the back of the
handle (See at right). For removing screws or easing drill bits out
of tight holes, release the trigger switch FIRST and then push the
slide switch up to reverse the drill motor. After any reversing
operations, return switch to forward position. Do not operate
reversing switch while unit is running. Do not run the Drill con
tinuously in Reverse — cooling fan functions most efficiently in
Forward.
It is possible that the slide switch will be in between the forward
or reverse position. In this case, the unit will not operate. Simply
push the slide switch fully to either the forward or reverse position
and the unit will operate when trigger is depressed.
CAUTION
Be sure to release the switch locking button before disconnecting the plug from the power
supply. Failure to do so will cause the too! to start immediately the next time it is plugged
In. Damage or Injury could occur.
Drilling
1. Always unplug the Drill when attaching or changing bits or accessories.
2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws.
For METAL, use high-speed steel twist drill bits or hole saws. For MASONRY, such as brick, cement,
cinder block, etc., use carbide-tipped bits.
3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a wood
“Dack-up’' block to prevent damage to the material.
4. With Variable Speed Drills there is no need to center punch the point to be drilled. Use a slow
speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough
to drill without the bit skipping out.
5. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but
do not push hard enough to stall the motor or deflect the bit.
6. Be sure to brace yourself against the twisting action of the drill.
7. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER
OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL-THIS CAN DAMAGE THE DRILL.
8. To minimize stalling on breaking through the material, reduce pressure on drill and ease the bit
through the last fractional part of the hole.
9. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming.
OPERATION
Care in Drilling
Twist drills are brittle and will break if enough bending stress is applied To avoid
stress on the drill bit, try extending your index finger along the side of the drill
housing with your middle finger on the trigger. Remember — guide the tool, don t
force it! Should the tool become overheated, run it free of any load at maximum
speed. The drill will cool faster by running it without load.
Drilling in Metal
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass
which should be drilled dry. The cutting lubricant that works best is sulphurized
cutting oil. Aluminum is best drilled with kerosene.
Drilling in Wood
Holes in wood can be made with the same twist drills used for metal. These bits
may overheat unless pulled out frequently to clear chips from the flutes. For
larger holes, use Power Drill Wood Bits with a shank size that will fit your drill's
chuck. Work that is apt to splinter should be backed up with a block of wood. Let
up on the pressure just before the tip cuts through, this will give a good clean hole.
Always leave the drill running when pulling it back out of a drilled hole, this
prevents jamming.
Accessories
Recommended accessories for use with your Drill are shown below and in Black &
Decker catalogs (CAUTION: The use of any other accessory might be more hazard
ous). For safety in use, the following accessories should be used only in the sizes
specified below:
BITS, METAL DRILLING — Up to Va" with DRILL, up to with ¥b" DRILL.
BITS, MASONRY DRILLING —Up to V2".
BITS, WOOD DRILLING — Up to with DRILL: up to ¥4" with DRILL.
HOLE SAWS — Up to IVa" with V4" DRILL*, up to l»/2'''with ¥b" DRILL.
WIRE BRUSHES & GRINDING WHEELS — up to 3" diameter.
BUFFING WHEELS —Up to 4" diameter.
BACKING PADS —4%" diameter.
We strongly recommend that your first purchase be the No. U-2106 Safety Glasses
which should be worn when using all drill accessories.
cut larger diameter
holes in wood up
to thick.
POLISHING BONNETS. For cleaning,
polishing, waxing of
cars, floors, etc.
SAFETY GLASSES (No. U2106). Lightweight, clear plastic with side
shields. Wear alone or over regular glasses.
WIRE CUP BRUSH
removes rust, scale,
and old paint from
metal surfaces.
BENCH DRILL
STAND permits
steady, vertical
drilling for accurate
work,
WIRE WHEEL
BRUSHES clean
and burnish metal,
remove rust and
paint.
DRILL BIT SHARP
ENER enables you
to extend the use
ful life of your drill
bits.
Loading...