BITWAVE HBC200 User Manual
HBC 200
®
Helmet Communicator
User Manual
Welcome to
HBC200
Helmet Communicator
User Manual
®
HBC200
helmet communicator
control unit
Metal mounting bracket &
velcros for speakers
A clip bracket &
anti slip rubber patch
Hi-fi stereo headset
User manual
An AC charger &
USB charging cable
1
Contents
Contents ----------------------------------------------------------------------- 1
Quick User Guide ----------------------------------------------------------- 3
Warnings and Safety Instructions --------------------------------------- 7
Features ----------------------------------------------------------------------- 9
Installation -------------------------------------------------------------------- 10
General Operations -------------------------------------------------------- 14
Mobile Phone Operations ------------------------------------------------ 16
Music Streaming Operations -------------------------------------------- 18
Intercom Operations ------------------------------------------------------ 19
Button Configurations Summary --------------------------------------- 25
Status Indicator Configurations Summary --------------------------- 26
Technical Data -------------------------------------------------------------- 27
Troubleshooting Operational Tips -------------------------------------- 28
Notices ------------------------------------------------------------------------ 29
2
Quick User Guide
Your HBC200 at a glance
GENERAL FUNCTIONS
Before using your HBC200 please charge it first!
Status Indicator
Charge
Check Bluetooth phone capabilities before use.
To charge, use the provided charging cable by
connecting it either to a USB port or to the
adaptor provided. While charging, the status
indicator light will be red. Upon fully charged,
the status indicator light will be blue.
Low Battery Indicator
You need to charge the helmet communicator
when the status indicator light blinks red twice
every 2 seconds with a beep every minute.
Install Speakers
Make sure the speaker wire is inserted into the
main unit. lnsert the speaker wire into the control
unit until you can no longer see the 3 ribs on the
speaker wire plug.
Answer Button Up Button
Down Button
3
Quick User Guide
Hold Answer for 2 seconds.
Hold Answer for 5 seconds.
*NOTE: The volumes for mobile phone, music and intercom functions are controlled separately.
MOBILE PHONE FUNCTIONS
Pairing your HBC200
with your mobile phone
Power On
Power Off
Volume Up
Press Up once.
Press all 3 buttons together.
Volume Down
Press Down once.
Pairing
>Check Bluetooth phone capabilities before use.
>Hold Up and Down buttons together
for 2 seconds. The status indicator
light will blink blue then red.
>From your mobile phone Bluetooth
menu, search for ‘UCLEAR HBC200’.
>If your phone requires a password,
enter ‘0000’.
Reset
4
Quick User Guide
Answer Incoming Call
Use voice pickup, say ‘hello’ or ‘pickup’.
Manually press Answer button once.
Reject/ End Incoming Call
Hold Answer button for 2 seconds.
*NOTE: For music Bluetooth adaptor you would need to pair the music Bluetooth adaptor before using it with HBC200.
Hold Up and Down buttons together for 2 seconds.
OR
MUSIC STREAMING FUNCTIONS
Pairing (for Music Bluetooth adaptor Only)
Last Number Redial
Use voice pickup, say ‘hello’
or ‘pickup’.
To swap between 2 concurrent calls, press
3 Way Calling
the Answer button once.
Play/ Stop (Quick Mute)
Press the Answer button 2 times.
Voice Dial
Hold Answer and Down
button for 2 seconds.
5
Quick User Guide
Press the Down button 2 times.
Backtrack
INTERCOM FUNCTIONS
Pairing your HBC200 to another HBC200
Helmet 1
(Master Unit)
Pairing (Needs to be done once)
The helmet communicator needs to be switched
1. Press Answer and Down buttons for 5 seconds on helmet 1.
Initiate Conversation
(Intercom Functions)
Hold the Up button for 2 seconds.
off before performing the following steps:
2. Press Answer and Up buttons for 5 seconds on helmet 2.
Fast Forward
Press the Up button 2 times.
Helmet 2
(Secondary Unit)
Terminate Conversation
(Intercom Functions)
Hold the Down button for 2 seconds.
6
Warning and Safety Instructions
This manual uses the and icons to highlight certain instructions.
Below is an explanation of the icons.
Attention
> This icon highlights special instructions and precautions intended to avoid damage
to the system. Non-compliance may void the product warranty.
Warning
> This icon provides precautions important to prevent injuries to the user.
Attention
> Please read through the operating instructions to understand how to operate the system,
in particular the safety instructions.
Warning
> Please note that there are some countries that by law disallow the rider to set the
helmet communicator to a volume that prevents you from perceiving the
surrounding.
> Please note that in some countries the use of both speakers simultaneously is
authorized only out of pubic traffic conditions.
> Please check with the relevant authorities for local safety legislation before using the
helmet communicator on the road.
7
Warnings and Safety Instructions
> Prolonged exposure to loud sounds may lead to permanent hearing damage.
> Do not attempt to place an outgoing call through the mobile phone while riding on the
motorcycle at any point of time.
> Please do not use the helmet communicator in anyway that may distract you
or hinder your judgment while on the move. Never ever compromise your safety and the
safety of others.
Attention
> Charging and handling rechargeable battery products incorrectly may cause them to
overheat, catch fire or explode. To prevent this please follow the instructions below:
i) Never change the batteries yourself, always bring the device to an authorised dealer to
perform the replacement for you.
ii) When charging, use ONLY the charging cable provided or a replacement cable from the
dealer. Using similar, compatible or any other cables may lead to permanent
product damage and will void the product warranty.
> Never make any modifications to any part of the helmet communicator in any
way as it may cause the system to malfunction causing hurt to you.
> Do not modify your helmet to use with this system - it is not necessary to do so.
8
Features
The helmet communicator has three main functions: to make mobile phone
calls, to listen to music and for intercom communication.
Mobile Phone Functions
• Bluetooth phone audio capabilities, HFP & HSP Profile.
• Voice activated call pick up.
Music Streaming Functions
• Bluetooth music streaming with hi-fi and stereo capabilities, A2DP Profile.
• Bluetooth Audio/Video Remote Control capability, AVRCP profile.
Intercom Functions
• Motorcycle to motorcycle or rider to passenger connection via two helmet
communicator up to 700m range.
Advanced Product Features
• Self adaptive intelligent noise cancellation algorithms ensure conversations on the go
are clear even in noisy environments.
• Voice controlled incoming call answering.
• The weather resistant engineered design ensures the possibility of communication
rain or shine.
• The integrated microphone array technology allows you to communicate without the
hassle of using boom microphones.
9
Installation
The HBC200 helmet communicator package contains :
1. A HBC200 helmet communicator
control unit
2. A pair of hi-fi stereo headset with embedded microphones
3. Velcros for speakers
4. A clip bracket and anti-slip rubber patch
5. A metal mounting bracket with double sided tape
6. An AC Charger and USB charging cable
7. User manual
10
Loading...