Bissell BS-7920F User Manual

Care and General Maintenance of your Bissell Cleaner

CONTENTS PAGE

BS-7920F Pro Heat Pro-Tech………….………………………Page 2

BS-1694F Powerwash Delux…………………………………..Page 4
BS-1950F Quickwash…………………………………………..Page 6
BS- 3750F Lift Off……………………………………………….Page 7

Prepared by Monique Lania 1Care & Maintenance of Bissell Deep Cleaner

BS-7920F Pro Heat Pro-Tech

Cleaning of the Red Lint Filter

Remove the lid from tank and turn the lid upside down

Remove red lint basket from tank lid and remove any debris stuck in lint basket with your finger tips or
an old toothbrush. If it is really dirty soak in hot water for 30 minutes and replace it back into machine

Once clean the red lint filter basket must be clicked securely in place and sealed to ensure maximum
suction.

Prevent solution build up in the machine by flushing the machine after
cleaning your carpet.

Fill the Tank-in-Tank with hot (not boiling) tap water and fill the SmartMix Bottle with tap water.

Switch grey SmartMix Switch located next to solution SmatMix bottle to
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting

Use the machine on hard surface such as concrete to suck up a quantity of clean
water. This will remove any solution build-up.

Empty collection tank and SmartMix bottle at the end of the procedure.

Remove tank-in-tank assembly from unit

Prepared by Monique Lania 2Care & Maintenance of Bissell Deep Cleaner

Cleaning of front window nozzle

Fill the Tank-in-Tank with clean tap water and fill the SmartMix Bottle with hot (not boiling) tap water.

Switch grey SmartMix Switch located next to solution SmatMix bottle to
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting

Use the machine on hard surface such as concrete to suck up a quantity of clean
water. This will remove any solution build-up.

Empty Collection Tank and SmartMix bottle at the end of the procedure.

For any difficult to remove debris that is trapped in the front window nozzle after flushing the
machine, it is advisable to use a thin piece of flexible plastic to dislodge the debris.

Cleaning underneath the front window nozzle

Wipe underneath surface with a soft cloth

Ensure after each use that hair and debris are removed from the brush roller using your fingertips or a
pair of scissors, paying particular attention to the leaver arms. This will prolong the life of the brush
belt.

Prepared by Monique Lania 3Care & Maintenance of Bissell Deep Cleaner

BS-1694F Powerwash Delux

Cleaning of the Red Lint Filter

Remove the lid from tank and turn the lid upside down

Remove red lint basket from tank lid and remove any debris stuck in lint basket with your finger tips or
an old toothbrush. If it is really dirty soak in hot water for 30 minutes and replace it back into machine

Once clean the red lint filter basket must be clicked securely in place and sealed to ensure maximum
suction.

Prevent solution build up in the machine by flushing the machine after
cleaning your carpet.

Fill the Tank-in-Tank with hot (not boiling) tap water and fill the SmartMix Bottle with tap water.

Switch grey SmartMix Switch located next to solution SmatMix bottle to
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting

Use the machine on hard surface such as concrete to suck up a quantity of clean
water. This will remove any solution build-up.

Empty collection tank and SmartMix bottle at the end of the procedure.

Remove tank-in-tank assembly from unit

Prepared by Monique Lania 4Care & Maintenance of Bissell Deep Cleaner

Cleaning of front window nozzle

Fill the Tank-in-Tank with clean tap water and fill the SmartMix Bottle with hot (not boiling) tap water.

Ensure after each use that hair and debris are removed from the brush roller using your fingertips
or a pair of scissors, paying particular attention to the leaver arms. This will prolong the life of the
brush belt.

Switch grey SmartMix Switch located next to solution SmatMix bottle to
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting

Use the machine on hard surface such as concrete to suck up a quantity of clean
water. This will remove any solution build-up.

For any difficult to remove debris that is trapped in the front window nozzle after flushing the
machine, it is advisable to use a thin piece of flexible plastic to dislodge the debris.

Cleaning underneath the front window nozzle

Empty collection tank and SmartMix bottle at the end of the procedure.

Wipe underneath surface with a soft cloth

Prepared by Monique Lania 5Care & Maintenance of Bissell Deep Cleaner

BS-1950F Quickwash

Cleaning Delivery Tank

Remove delivery tank and thoroughly rinse using hot (not boiling) tap water

Cleaning underneath the front window nozzle

Ensure after each use that hair and de br is are removed from the brush. This will
prolong the life of the brush.

Remove and empty Dirty Water Tank

Fill delivery tank with clean water only.

Use machine on concrete to suck up a quantity of clean water.

Wipe underneath surface with a soft cloth

Press detent pedal and tip handle back, laying unit flat on the floor

Release dirty water tank latches (grey latches, 1 on each side of unit) by pulling
up from the bottom of the latch and then out

Carefully lift blue dirty water tank from the lower body. Empty tank and rinse
thoroughly with hot (not boiling) tap water

Replace blue dirty water tank on lower body of unit and secure with latches

Prepared by Monique Lania 6Care & Maintenance of Bissell Deep Cleaner

BS- 3750F Lift Off – Refer to Yellow piece of paper supplied with
machine

Empty the clear plastic Dirt Container

Switch off the cleaner and unplug it from the electrical outlet

Place vacuum in upright position

Slide the Lock ‘n Seal Lever to the ‘unlock’ position

Grasp the handle and pull the Dirt Container straight out to remove from vacuum

Empty dirt into garbage container

Rinse plastic container in warm (not boiling), tap water (you can also use a mild
detergent) and dry thoroughly

Ensure container is 100% dry before placing back into vacuum

Put the Dirt Container back in the vacuum and slide Lock ‘n Seal Lever to the ‘lock’ position

Prepared by Monique Lania 7Care & Maintenance of Bissell Deep Cleaner

Clean the filters

1. Upper-tank Filter

The upper tank filter can be reached by removing the Dirt Container, reaching in underneath the
Upper Tank and turning the rim of the red Filter Frame to unlock. Pull it straight down to remove.

The Upper Tank and Louvers may be wiped clean using a damp cloth and then dried using a dry cloth.

The foam Upper Tank filter may be removed and hand washed in cold tap water with a mild
detergent. Rinse well and then air dry thoroughly. **Ensure filter is 100% dry before placing
back into vacuum

Switch off the cleaner and unplug it from the electrical outlet

Brush the dirt off the Upper Tank and Louvers.

**NOTE: For easier access the entire Upper Tank may be removed by turning the red
knob on the back of the cleaner to ‘unlock’ position and pulling the entire tank straight
out. Ensure the knob is turned back to ‘lock’ when Upper Tank is replaced back in
cleaner.

2. Pre-motor Filter

Pull out the black slide-out tray located underneath the Dirt Container

Lift out the foam filter

The foam filter may be hand washed in cold tap water with a mild detergent.
Rinse well and then air dry thoroughly. **Ensure filter is 100% dry before placing
back into vacuum

Prepared by Monique Lania 8Care & Maintenance of Bissell Deep Cleaner

3. Hepa 12 Media Post-Motor Filter

The HEPA Filter is located on the back of the cleaner behind the white door

Open the door, pulling it downwards, remove the filter and gently tap it against
the palm of your hand to remove access dust and dirt.

Replace filter if necessary

Prepared by Monique Lania 9Care & Maintenance of Bissell Deep Cleaner