Page 1
USER'S GUIDE
42A8-E SERIES 220-240V
2
Thank You
3
Safety Instructions
4
Product View
5
Assembly
6-8
Operations
™
9
Maintenance and Care
10
Troubleshooting
10
Replacement Parts
10
Additional Accessories
11
Warranty
12
Consumer Care
INCLUDES
2 Microfibre Mop Pads
with Microban™
Antibacterial Protection
Page 2
Thanks for buying a BISSELL Steam&Sweep Hard Floor Cleaner
We’re glad you purchased a BISSELL Steam&Sweep Hard Floor Cleaner.
Everything we know about floor care went into the design and construction
of this complete, high-tech home cleaning system.
Your Steam&Sweep Hard Floor Cleaner is well made, and we back it with a
limited two year warranty. We also stand behind it with a knowledgeable,
dedicated Consumer Care department, so, should you ever have a
problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL
is a global leader in the design, manufacture, and service of high quality
homecare products like your Steam&Sweep Hard Floor Cleaner.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman & CEO
2
www.bissell.com
Page 3
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
READ ALL INSTRUCTIONS
BEFORE USING STEAM&SWEEP.
Always connect to a properly Earthed outlet.
Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
WARNING: To
reduce the risk of fire, electric
shock, or injury:
■
Use indoors only
■
Do not immerse
■
Use only on surfaces moistened by cleaning
process
■
Do not leave machine when it is plugged in
■
Do not service machine when it is plugged in
■
If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent in order to avoid a hazard
■
Do not use machine if it has been dropped,
damaged, left outdoors or dropped into water
■
Do not expose to rain, store indoors
■
Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces
■
Do not carry the appliance while in use
■
Do not unplug by pulling on cord; unplug
by grasping plug not the cord
■
Do not handle plug or appliance with wet
hands
■
Do not put any object into appliance openings,
use with blocked opening or restrict air flow
■
Do not expose hair, loose clothing, fingers or
body parts to openings or moving parts
■
Do not pick up hot or burning objects
■
Do not pick up flammable or combustible materi-
als (lighter fluid, petrol, kerosene, etc.) or use in
the presence of explosive liquids or vapours
■
Do not use appliance in an enclosed space filled
with vapours given off by oil base paint, paint
thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapours
■
Remove plug from electrical outlet before
cleaning or maintaining the appliance
■
Do not run appliance over supply cord. A
hazard may occur if the appliance runs
over the supply cord
www.bissell.com
■
Not intended for use by persons (including chil-
dren) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance
by a person responsible for their safety
■
Young children should be supervised to ensure
that they do not play with the appliance
■
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, petrol, etc.)
■
Do not modify the Earthed plug
■
Do not allow to be used as a toy
■
Do not use for any purpose other than
described in this User’s Guide
■
Use only manufacturer’s recommended
attachments
■
Use only cleaning products formulated by
BISSELL for use in this appliance to prevent internal component damage
■
Keep openings free of dust, lint, hair, etc.
■
Keep appliance on a level surface
■
Turn off all controls before unplugging
■
Be extra careful when cleaning stairs
■
Liquid or steam must not be directed towards
equipment containing electrical components
■
Pay close attention when working around children
SAVE THESE
INSTRUCTIONS.
THIS MODEL IS FOR HOUSEHOLD
USE ONLY.
WARNING:
appliance must be Earthed
The symbol means WARNING:
Danger of scalding.
Surface may be hot. Avoid contact.
This
.
IMPORTANT FOR
OPERATION ON A 220-240 VOLT A.C.
50/60 Hz POWER SUPPLY ONLY.
If your appliance is fitted with a nonrewireable BS
1363 plug it must not be used unless a 13 amp
(ASTA approved to BS 1362) fuse is fitted in the carrier contained in the plug. Spares may be obtained
from your BISSELL supplier. If for any reason the plug
is cut off, it must be disposed of, as it is an electric
shock hazard should it be inserted into a 13 amp
socket.
3
Page 4
Product view
INCLUDES
2 Microfibre Mop Pads
with Microban™
Antibacterial Protection
Bacteria Build-Up on Non-Microban
(left) vs. Microban Mop Pad (right)
Power
Cord
Brush
Switch
Quick
Release
Cord
Wrap
Handle
Power
Switch
™
Water
Tank
In between uses, bacteria can quickly
multiply in number on an unprotected
steam mop pad. Microban®
antibacterial protection helps prevent
the growth of 99.9% of harmful
bacteria on the pad surface. And
because Microban technology works
continuously, your pad will now stay
cleaner and fresher between uses.
This information is based upon standard laboratory tests and is
provided for comparative purposes to substantiate antimicrobial
activity for non-public health applications. Microban® technology
is not designed to replace regular cleaning practices or protect
users from disease causing microorganisms. Antimicrobial action
limited to product surfaces.
MICROBAN is a registered trademark of Microban Products
Company.
4
www.bissell.com
Ready
Light
Dirt Bin
Release Pedal
Filter
Manoeuvrable
Swivel Head
Page 5
Assembly
Your Steam&Sweep Hard Floor Cleaner
assembles quickly and easily. The only
tool you will need for assembly is a Phillips
head screwdriver.
Your Steam&Sweep is packaged
with the following items:
Handle Assembly
Lower Body with Water Purification
System
Manoeuvrable Swivel Head
Removable Water Tank
1 large Phillips Head Screw
1 small Phillips Head Screw
2 Mop Pads
Attach handle to Steam&Sweep
Hard Floor Cleaner
1. Attach lower body to manoeuvrable
swivel head (If your Steam&Sweep came
with the swivel head already assembled
to the body, you may skip
this step).
2. Secure manoeuvrable swivel head
with small Phillips head screw. Tighten
until secure.
1.
2.
3. Slide handle assembly down into lower
body until it will go no further.
4. Secure the handle by placing the large
Phillips head screw through the screw
opening in the lower body and into the
rear of the handle assembly. Tighten with
screwdriver until secure.
5. Slide water tank onto lower body by
lining up vertical glides and gently
sliding tank into place.
Steam&Sweep assembly is now complete.
www.bissell.com
3.
5.
4.
5
Page 6
Operations
Special Features
Removable water tank
The water tank is located on the back of
the Steam&Sweep. It can be refilled with
water any time during use. Distilled or
demineralized water is recommended in
place of tap water.
Do not use chemicals with your
Steam&Sweep.
Water purification system
This filter removes minerals and other
impurities from tap water, preventing
water deposits from damaging your
Steam&Sweep. It should be replaced
when the bright green grains turn blue.
To maximize performance of the filter, distilled water should be used.
Ready light
The ready light will glow when water
has been converted to steam and the
Steam&Sweep is ready to use.
Steam on demand trigger
Press to release steam.
Manoeuvrable swivel head
Allows you to pick up dust and small
debris while steam cleaning your floor.
The manoeuvrable swivel head gets into
tight spaces and under cabinets.
Tip:
To prevent damage to the machine,
do not attempt to use your
Steam&Sweep without water in
the tank.
Microfibre mop pads
These washable, reusable microfibre pads
feature buit-in Microban® antibacterial
protection to help prevent the growth of
99.9% of harmful bacteria on the pad surface to keep your pad fresher between uses..
Getting ready
1. The mop pad may have already come
attached to the swivel head. If not, attach
mop pad to swivel head using the Velcro
strips.
2. Fill the water tank.
A. Remove the tank by lifting straight up
and away from the unit.
B. Unscrew the cap at the bottom of
the water tank and remove the insert
assembly.
6
www.bissell.com
2A.
2B.
Page 7
Operations
C. Fill the water tank with water. For
best results, water should be at room
temperature.
D. Replace the insert assembly and cap,
tighten until snug.
E. Replace the water tank by lining up
the vertical guides and gently sliding it
back into place.
3. Twist the quick release cord wrap
clockwise to unwrap the power cord
completely, make sure both switches are
in the "OFF" position and plug it into a
proper outlet.
4. Turn power button on. The ready light
will illuminate when the Steam&Sweep is
ready for use.
NOTE: Upon first use of the
Steam&Sweep or first use of a
new filter, the pump may make a
“knocking” sound while the filter
fills with water. This sound is normal
and may last a couple of minutes.
Continue to depress the trigger until
the knocking sound subsides and
the unit emits steam. If the sound
continues, please make sure the
tanks are firmly secured.”
2D.
2E.
WARNING:
Steam&Sweep will not pick up
crayons, marbles, and other
large objects.
Before you clean
The Steam&Sweep can be used as a sweeper
and a steam mop at the same time. For best
results, use the Steam&Sweep's powerful sweeper to clear floor of dust and small debris before
mopping.
1. Turn the brush switch to the On ( I )
position to activate the brush.
2. To empty the dirt container, turn the
power off, gently tap the release
pedal on the swivel head. Lift unit
straight up leaving bin on floor and
empty into a trash can. The dirt
container may be warm to the touch.
3. Replace the dirt container by pushing
it back into the swivel head until it
snaps back into place.
www.bissell.com
Brush Switch
Dirt Bin
Release Pedal
1.
Power Switch
2.
7
Page 8
Operations
Steam cleaning hard floors
Your Steam&Sweep is designed to clean
hard flooring such as ceramic tile, vinyl,
marble, stone and sealed hard wood
floors. Use of your Steam&Sweep on
waxed or some unwaxed floors may
result in a diminished glossiness. The
Steam&Sweep is not for use on unsealed
wood floors. Ensure that the Steam&Sweep
is throughly tested in an inconspicuous
area prior to cleaning a large floor area.
Also be sure to check the care instructions
from your flooring manufacturer.
1. When the ready light illuminates,
begin cleaning by slowly passing
over the surface while pressing the
steam on demand trigger to emit
steam as needed.
WARNING:
Never put descaling aromatic,
alcoholic, or detergent products
into the steam cleaner, as this
may damage it or make it unsafe
for use.
Tip:
The Steam&Sweep may be used as
both a steam mop and a sweeper at
the same time.
2. To sanitize an area of your floor,
(attack invisible germs and bacteria)
leave the Steam&Sweep over the area
for a minimum of 15 seconds using
continuous steam, but no longer than
20 seconds. For larger areas, overlap
swivel head placement.
3. When the Steam&Sweep stops emit-
ting steam, turn the unit off. Simply
remove the water tank, refill, and
continue cleaning.
NOTE: Upon first use of this
steam product or first use of
a new filter, the pump may
make a "knocking" sound while
the filter fills with water. This
sound is normal and may last
up to one minute. Continue to
depress the trigger until the
knocking sound subsides and
the unit emits steam.
CAUTION:
Exercise extreme care when using
the Steam&Sweep on timber flooring. Ensure the Steam&Sweep is
thoroughly tested in an inconspicuous area prior to mopping a large
floor area. The Steam&Sweep
generates hot steam, so when
depressing the trigger to apply
steam, ensure the Steam&Sweep
is moving continuously. The trigger
does not need to be depressed at
all times. Prolonged application
of steam in one area increases
the risk of damage to the surface
treatment on timber floors. Check
with your timber floor treatment
and application specialist prior to
team&Sweep operation. Regular
foot traffic and direct sunlight will
wear down timber floor surface
treatment, making it more susceptible to steam damage. Exercise
extreme care when using the
Steam&Sweep on timber flooring.
8
www.bissell.com
Page 9
Maintenance and care
When you’re done
1. Make sure both power switches are
in the OFF (O)position. Unplug power
cord from outlet.
2. Carefully remove mop pad from
swivel head, as mop pad and lower
assembly will be hot.
3. Any water remaining in the water
tank should be emptied prior to
machine storage.
4. Mop pad can be machine washed in
warm water with mild detergent. Do
not use bleach or fabric softeners. For
best results, air dry.
5. Wrap power cord around quick
release cord wrap on side of Steam
& Sweep.
6. Wipe all surfaces of Steam&Sweep
with a soft cloth. Store upright in a
protected, dry area.
NOTE: If steam output is reduced,
the nozzle may be blocked. To
remedy, unplug the unit, remove
the swivel head from the lower
body and pour vinegar through
the center tube of the swivel
head “neck”. Clear the nozzle
by inserting a paper clip into the
brass spray tip located in the
bottom of the lower body.
CAUTION:
Upright storage of the
Steam&Sweep with a wet mop
pad may result in the formation
of white marks on your floor. To
remove the white marks, clean
area with vinegar.
Replacing the water purification system
If you fill your Steam&Sweep cleaner with
normal tap water, it is essential to check
the filter and replace it when it is no longer
effective. Change the filter when the bright
green grains turn blue. If the filter is not
changed at the appropriate time, calcium
deposits will accumulate on the heating
element, causing damage or reduced performance.
To replace the filter, pull it up and away
from the Steam&Sweep.
Using distilled or demineralized water will
maximize the performance of your filter.
To order a replacement filter, refer to the
replacement parts section on page 10.
www.bissell.com
Tip:
Using distilled or demineralized
water will maximize the performance
of your filter.
Tip:
Be sure to use only a BISSELL water
filter in your Steam&Sweep.
9
Page 10
Troubleshooting
Reduced steam or no steam
Possible causes Remedies
1. Water tank is empty 1. Fill water tank
2. Depleted water filter 2. Replace filter
3. Blocked steam nozzle 3. Refer to NOTE in the middle of page 9.
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
NOTE: There are no serviceable parts in the upper housing of this product.
Please do not return this product to the store.
Replacement parts - BISSELL Steam&Sweep
Item Part No. Part Name
1 218-5600 Water filter
2 203-2246 Handle assembly with screw
3 203-2243 Water tank with cap and insert
4 203-2168 Storage hook with screws
1 2 3 4
Additional accessories
Item Part No. Part Name
1 8724 Microfibre mop pads – 2 pack
1
10
www.bissell.com
Page 11
Warranty - BISSELL Steam&Sweep Hard Floor Cleaner
This warranty gives you specific legal rights, and you may also have other rights which may
vary from country to country. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail,
telephone, regular mail as described below, or contact your local in country distributor.
Limited Two Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL will repair or replace
(with new or remanufactured components or products), at BISSELL’s option, free of charge from
the date of purchase by the original purchaser, for two years any defective or malfunctioning
part due to manufacturer defect.
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters. Damage or
malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in
accordance with the User's Guide is not covered.
BISSELL recommends that the original packaging be kept for the duration of the warranty
period in case such need arises within the warranty period that the item need re-packing
and transportation.
BISSELL Consumer Care:
If your BISSELL product should require service or if you need information about repairs,
authorized service centers in your area, replacement parts or your warranty, please contact
BISSELL Consumer Care, as indicated below, or contact your local in-country distributor.
For UK inquiries:
Telephone: 0844.888.6644
Monday – Thursday 9 am – 5 pm
Friday 9 am – 4 pm
Or write:
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire, SL1 4QT
United Kingdom
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
BISSELL and ItS In-country dIStrIButorS arE not LIaBLE For IncIdEntaL or conSEQuEntIaL daMaGES
oF any naturE aSSocIatEd WItH tHE uSE oF tHIS Product. BISSELL’S LIaBILIty WILL not EXcEEd tHE
PurcHaSE PrIcE oF tHE Product.
tHIS Warranty IS EXcLuSIVE and In LIEu oF any otHEr WarrantIES EItHEr oraL or WrIttEn. any
IMPLIEd WarrantIES WHIcH May arISE By oPEratIon oF LaW, IncLudInG tHE IMPLIEd WarrantIES oF
MErcHantaBILIty and FItnESS For a PartIcuLar PurPoSE, arE LIMItEd to tHE tWo yEar duratIon FroM
tHE datE oF PurcHaSE aS dEScrIBEd aBoVE.
For all other inquiries:
USA Headquarters
01.616.453.4451
Monday – Friday 8 am – 4 pm
Or write:
BISSELL Homecare, Inc.
P.O. Box 1888
Grand Rapids, Michigan, 49501
USA
www.bissell.com
11
Page 12
BISSELL consumer care
For information about repairs or replacement parts, or questions about your
warranty, please call BISSELL Consumer Care:
For UK inquiries:
Telephone: 0844.888.6644
Monday – Thursday 9 am – 5 pm
Friday 9 am – 4 pm
Or write:
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
For all other inquiries:
USA Headquarters
01.616.453.4451
Monday – Friday 8 am – 4 pm
Or write:
BISSELL Homecare, Inc.
P.O. Box 1888
Grand Rapids, Michigan, 49501
USA
Berkshire, SL1 4QT
United Kingdom
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt.
It provides proof of purchase date in the event
of a warranty claim. See Warranty on page 11
for details.
12
www.bissell.com
©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4608
Rev 9/12
Visit our website at:
www.bissell.com
MICROBAN is a registered trademark
of Microban Products Company.
Loading...