Bissell 3574, 3576 User Manual 2

USER’S GUIDE

3574/3576 SERIES

Safety Instructions

Product View

Assembly Instructions

5-6

Operation / Special Tools

6-8

Maintenance

8-11

Troubleshooting

12-13

Warranty

Replacement Parts

Consumer Services

CleanView®II

BAGLESS

Thanks For Buying A BISSELL CleanView®II

We’re glad you purchased a BISSELL CleanView II Vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home vacuuming system.

Your BISSELL CleanView II is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your BISSELL CleanView II.

Thanks again, from all of us at BISSELL.

Mark J. Bissell President and Chief Executive Officer

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical

appliance, basic precautions should be observed, including the following:

READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.

Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance.

WARNING: To reduce

the risk of fire, electric shock, or injury:

■

Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

■

Do not leave vacuum cleaner unattended

when it is plugged in.

■

Unplug from outlet when not in use and

before servicing.

■

Do not use outdoors or on wet surfaces.

■

Do not allow children to operate vacuum

cleaner or use as a toy.

■

Close attention is necessary when used by or

near children.

■

Do not use for any purpose other than described

in this User’s Guide.

■

Use only manufacturer’s recommended

attachments.

■

Do not use with damaged cord or plug.

■

If appliance is not working as it should,

has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.

■

Do not pull or carry by cord, use cord as a

handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

■

Do not unplug by pulling on cord. To unplug,

grasp the plug, not the cord.

■

Do not handle vacuum cleaner or plug with

wet hands.

■

Do not put any object into openings.

Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.

■

Keep hair, loose clothing, fingers, and all parts

of body away from openings and moving parts.

■

Turn off all controls before plugging or

unplugging vacuum cleaner.

■

Use extra care when cleaning stairs.

■

Unplug before attaching the turbobrush.

■

Do not pick up flammable materials (lighter

fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapors.

■

Do not pick up toxic material (chlorine bleach,

ammonia, drain cleaner, etc.).

■

Do not use vacuum cleaner in an enclosed

space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.

■

Do not pick up hard or sharp objects such as

glass, nails, screws, coins, etc.

■

Do not pick up anything that is burning

or smoking, such as cigarettes, matches, or hot ashes.

■

Do not use without filters in place.

■

Use only on dry, indoor surfaces.

■

Keep appliance on a level surface.

■

Do not carry the vacuum cleaner while it

is running.

WARNING: The Power Cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

THIS APPLIANCE HAS A POLARIZED PLUG.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

This model is for household use only.

CAUTION:

Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.

Power Switch

Carrying Handle

Crevice Tool

Post-Motor Filter

Quick Reach

Handle

Quick Release Cord Wrap

Handle Release Pedal

Powerfoot

Stretch Hose

Extension Wand

Power Cord

Furniture Protection Guard

Height Adjustment Knob

Upper Tank

Dirt Container

Lock ’n Seal

™

Lever

Headlight

Combination Dusting Brush/ Upholstery Tool

Hose Wand

Hose Clip

Furniture Protection Guard

Optional Hepa Media Filter (Select Models Only)

Hose Wand Base

Louvers

Stair Cleaning Handle

Inner and Outer Circular Filters

Filter Cup

Wide Cleaning Path Models

Foot Hose

Cord Clip

How To Use This Guide

This User’s Guide has been designed to help you get the most satisfaction from your BISSELL CleanView II. You’ll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your vacuum cleaner.

Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they fit. Following this User’s Guide will greatly enhance your ability to get the most performance from your BISSELL CleanView II for many years.

The only tool you’ll need to assemble your vacuum cleaner is a screwdriver.

Locate the vacuum Handle and remove the screw packet taped to the base of the Handle.

Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body.

Check to be sure the Handle is fitted to the vacuum body. If there is a gap in front, continue to push firmly until the Handle is flush.

Insert the screw provided from the screw packet into the existing hole. Tighten securely with a screwdriver.

Attach the Twist ‘n Snap

™

Hose by lining up the tabs on the base with the corresponding notches on the back of the vacuum as shown.

Turn the Twist ‘n Snap Hose to the right to lock the hose into place.

Grasping the Quick Reach Handle, slide the end of the Hose Wand onto the Hose Wand Base. Snap the Hose into the Hose Clip.

NOTE: The Powerfoot will not operate effectively unless the Hose Wand is firmly attached.

Attach Handle To Vacuum

How To Put It Together

Attach Vacuum Hose and Tools

WARNING:

Plastic film can be dangerous. To avoid danger of suffocation, keep away from babies and children.

+ 11 hidden pages