Bissell 1838 User Manual

CLEANVIEW®
REWIND PET

Vacuum

___________

USER GUIDE

1838 SERIES

More of a video
person? Look for this
icon and go online
for an instructional
how-to video at

www.BISSELL.com

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.

Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in
use and before conducting maintenance. When using an electrical appliance, basic precautions should be
observed, including the following:

WARNING

TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:

» Do not leave vacuum cleaner when it

is plugged in. Unplug
from outlet when not in use
and before servicing.

» Do not use outdoors or on

wet surfaces.

» Do not allow to be used as a toy.

Close attention is necessary when
used by or near children.

» Do not use for any purpose other

than described in this User’s
Guide. Use only manufacturer’s
recommended attachments.

» Do not use with damaged cord or

plug. If appliance is not working
as it should, has been dropped,
damaged, left outdoors, or dropped
into water, have it repaired at an
authorized service center.

» Do not pull or carry by cord, use

cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord away
from heated surfaces.

» Do not unplug by pulling on

cord. To unplug, grasp the plug, not
the cord.

» Do not handle plug or vacuum

cleaner with wet hands.

» Do not put any object into

openings. Do not use with any
opening blocked; keep openings free
of dust, lint, hair, and anything that
may reduce air flow.

» Keep hair, loose clothing, fingers,

and all parts of body away from
openings and moving parts.

» Turn off all controls before

plugging or unplugging
vacuum cleaner.

» Use extra care when cleaning

on stairs.

» Do not use to pick up flammable or

combustible materials (lighter fluid,
gasoline, kerosene, etc.)
or use in areas where they may
be present.

» Do not use vacuum cleaner in an

enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.

» Do not use to pick up toxic

material (chlorine bleach,
ammonia, drain cleaner, etc.).

» Do not pick up anything that is

burning or smoking, such as

cigarettes, matches, or hot ashes.
» Do not use without filters in place.
» Do not pick up hard or sharp objects

such as glass, nails, screws, coins, etc.
» Use only on dry, indoor surfaces.
» Keep appliance on a level surface.
» Do not carry the vacuum cleaner

while it is running.
» Unplug before connecting or

disconnecting the TurboBrush® Tool.
» Hold plug when rewinding onto cord

reel. Do not allow plug to whip when

rewinding.

SAVE THESE INSTRUCTIONS

This model is for household use only.

WARNING

››

Before using your vacuum, make sure the dirt container is in locked position and that all filters,

both pre- and post-filters are in place. DO NOT operate your vacuum without these filters.
›› Plastic film can be dangerous. To avoid danger of suocation, keep away from children.
›› Do not plug in your vacuum UNTIL you are familiar with all instructions and operating

procedures.
›› To reduce the risk of electrical shock, turn power switch o and disconnect polarized

plug from electrical outlet BEFORE performing maintenance or troubleshooting checks.

THIS APPLIANCE HAS
A POLARIZED PLUG

To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a proper outlet. Do not change the plug in any way.

www.BISSELL.com

2

Hot

Neutral

Thanks for buying a BISSELL vacuum!

We love to clean and we’re excited to share one of our innovative products
with you. This guide has important instructions on how your new vacuum
works, including using (page 6), maintaining (pages 7-9), and if there is a
problem, troubleshooting (page 10).

In just a few simple assembly steps, you’ll be ready to vacuum. Flip to page
5 and let’s get started!

What’s In The Box?

1.

5. 6. 7. 8. 9.

2. 3. 4.

Safety Instructions...........2

Product View................4

Assembly ...................5

1. Vacuum Base

2. Handle

3. Hose

4. 2 Screws

(taped to Handle)

5. Extension Wand Clip
6 Extension Wand

7. Crevice Tool
(stored inside Extension Wand)

8. TurboBrush® Tool

9. Dusting Brush

NOTE: Not all accessories
come with every model. Be
sure to check the carton for
additional tools.

Warranty ....................11

Service ......................11

Contact Information ........12

Operations ..................6

Maintenance & Care .......7-9

Troubleshooting ............10

Product Registration........12

Parts & Supplies ............12

www.BISSELL.com

3

Product View

WARNING

Do not plug in your vacuum until you are familiar with all instructions and operating procedures.

Handle

Power
Button

Cord
Rewind

Stretch

Hose

Suction
Indicator

Extension
Wand Clip

Extension
Wand

Recline
Pedal

NOTE: The Crevice Tool is stored inside the Extension Wand.

Tank
Release
Button

Carry Handle

Pre-Motor
Filter

(not shown)

Dirt Tank

Post-Motor
Filter

Height

Adjustment

www.BISSELL.com

4

Assembly

The only tool you will need to assemble
your vacuum is a Phillips screwdriver.

1

Place handle on
vacuum base and
press down firmly.

3

Place extension wand clip on back
of unit, twist clockwise to lock in.

2

Insert screws in
back of unit.

Tighten by rotating
the screw clockwise
until tightened.

4

Line up tabs on hose end to vacuum base and
twist clockwise to lock in.

5

Wrap hose up and around the
hose wrap on the handle. Slide
end of hose into vacuum base.

NOTE: The powerfoot will not suction properly unless the hose is firmly attached.

6

Store
TurboBrush®
on front of
handle.

Store dusting

7

brush above hose
wrap in holder.

www.BISSELL.com

5

Operations: Power On & Settings

1

Power
Button

Push the Power
Button on the
handle once to turn
the unit ON and
once again to turn
the unit OFF.

2

Press the recline pedal and pull handle
back towards you.

3

Turn the dial on the foot of the vacuum to the desired
setting. If the dial is difficult to turn, tilt the vacuum back
slightly to take the weight off the foot while turning.

Lowest setting – For low pile carpet or bare floors.
To pick up debris, it may be necessary
to move up one setting.

Medium setting – For medium pile carpet.
Highest setting – For high pile and most shag carpet.

TIP: For optimal carpet

cleaning performance,
adjust to the lowest
practical setting. If your
vacuum is difficult to
push, adjust to the next
higher setting.

TIP: To operate the cord
rewind, gently pull out
power cord and stop when
yellow band is visible on
the cord. Do not pull power
cord beyond the red line.
To return cord, hold plug
and press automatic cord
rewind button locate on
the lower side of the unit.
Do not allow plug to whip
when rewinding.

WARNING

To reduce the risk of injury from moving parts while the vacuum is turned on, always move the
vacuum via the rolling wheels by using the upper handle at the back of the vacuum. Do not carry
the vacuum while it is running. Always place vacuum on floor with handle in upright position
when using tools.

NOTE: The rotating floor brush continues to rotate while tools are in use. Never place your
fingers under the vacuum when it is running. Never place powerfoot on furniture or uneven
surfaces. Do not place vacuum close enough to objects to pull them into rotating brush.

NOTE: Certain carpets and low humidity conditions may generate small static discharges.
Static discharges are entirely harmless and are not associated in any way with the main
power supply.

www.BISSELL.com

6

Maintenance: Clean Dirt Tank

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect polarized plug
from electrical outlet before performing maintenance or troubleshooting checks.

1

Empty once tank is full.

3

Hold the dirt
tank over a trash
container.

Press the lid release
button to empty.
Once empty, close
the lid.

2

4

Press tank
release button
and remove
dirt tank.

Twist cyclone
counter clockwise
and pull down to
remove from tank.

5

NOTE: The dirt tank may be washed in warm water with a mild detergent. Make sure it is
completely dry before replacing.

Clean cyclone with
warm water and mild
detergent.

Let cyclone
completely dry before
replacing.

To replace, align arrow
on cyclone with the
unlock ICON on the
back of the tank. Press
in and turn clockwise
to lock.

6

click

After emptied,
place tank back
on vacuum and
press firmly until
you hear “click”.

www.BISSELL.com

7

Maintenance: Pre-Motor Filter

WARNING

1

3

Do not operate vacuum with damp or wet filters
or without all filters in place.

Press tank
release button
and remove
dirt tank.

To access filter,
Press the Filter
button on
front.

Make sure filter
is completely dry
before placing back
into the tank lid.

Close the lid to
return the tank to
the vacuum.

2

Remove foam
filter from tray.
Hand wash in
warm water;
mild detergent
may be used if
desired. Rinse well
and then air dry
thoroughly.

4

click

Return tank back
on vacuum and
press firmly until
you hear “click”.

Maintenance: Post-Motor Filter

1

Firmly pull filter tray out.

NOTE: The pleated post-motor filter may NOT be washed with water or detergent. Replace the
post-motor filter every 3 to 6 months.

www.BISSELL.com

8

2

Push pleated filter
down through filter
tray.

NOTE:
If dust and/or debris
accumulates on the
filter, gently tap the
filter on the side of
a garbage container.