Bissell 1305, 1306, 1646, 1647 User Manual

POWERCLEAN®

Vacuum

___________

USER GUIDE

1305, 1306, 1645, 1646, 1647 SERIES

For How-To
videos, go to

www.BISSELL.ca

Sections marked
with this video
icon have more
information online.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.

Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in
use and before conducting maintenance. When using an electrical appliance, basic precautions should be
observed, including the following:

WARNING

TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:

» Always connect to a polarized

outlet (one slot is wider than
the other). Do not modify the
polarized plug to fit a non-polar
ized outlet or extension cord.

» Do not leave vacuum cleaner

when it is plugged in. Unplug
from outlet when not in use
and before servicing.

» Do not use outdoors or on

wet surfaces.

» Do not allow to be used as a toy.

Close attention is necessary when
used by or near children.

» Do not use for any purpose other

than described in this User’s
Guide. Use only manufacturer’s
recommended attachments.

» Do not use with damaged cord or

plug. If appliance is not working
as it should, has been dropped,
damaged, left outdoors, or
dropped into water, have it repaired
at an authorized service center.

-

» Do not pull or carry by cord, use

cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.

» Do not unplug by pulling on

cord. To unplug, grasp the plug,
not the cord.

» Do not handle plug or vacuum

cleaner with wet hands.

» Do not put any object into

openings. Do not use with any
opening blocked; keep openings
free of dust, lint, hair, and anything
that may reduce air flow.

» Keep hair, loose clothing, fingers,

and all parts of body away from
openings and moving parts.

» Turn off all controls before

plugging or unplugging
vacuum cleaner.

» Use extra care when cleaning

on stairs.

» Do not use to pick up flammable

or combustible materials (lighter
fluid, gasoline, kerosene, etc.)
or use in areas where they may
be present.

» Do not use vacuum cleaner in an

enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust, or
other explosive or toxic vapors.

» Do not use to pick up toxic

material (chlorine bleach,
ammonia, drain cleaner, etc.).

» Do not pick up anything that is

burning or smoking, such as

cigarettes, matches, or hot ashes.
» Do not use without filters in place.
» Do not pick up hard or sharp

objects such as glass, nails, screws,

coins, etc.
» Use only on dry, indoor surfaces.
» Keep appliance on a level surface.
» Do not carry the vacuum cleaner

while it is running.
» Unplug before connecting or dis

connecting the TurboBrushTM Tool.

SAVE THESE INSTRUCTIONS

This model is for household use only.

-

WARNING

›› Plastic film can be dangerous. To avoid danger of suocation, keep away from children.

›› Do not plug in your vacuum cleaner UNTIL you are familiar with all instructions and

operating procedures.

›› To reduce the risk of electrical shock, turn power switch o and disconnect polarized

plug from electrical outlet BEFORE performing maintenance or troubleshooting checks.

THIS APPLIANCE HAS

Hot

A POLARIZED PLUG

To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a proper outlet. Do not change the plug in any way.

www.BISSELL.ca

2

Neutral

Package Contents

TurboBrush

Crevice

Tool

User

Guide

TurboBrushTM

Tool & Clip

Extra

Reach

Hose

Upper
Handle

NOTE: Standard accessories may vary by

model. Additional tools may vary – check
carton for contents.

Base Unit

Thanks for buying a BISSELL vacuum

We’re glad you purchased a BISSELL
vacuum. Everything we know about
floor care went into the design and
construction of this complete, high­tech home cleaning system.

Your BISSELL vacuum is well made,
and we back it with a limited
five-year warranty. We also stand
behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.

My great-grandfather invented
the floor sweeper in 1876. Today,
BISSELL is a global leader in the
design, manufacture, and service
of high quality homecare products
like your BISSELL vacuum.

Safety Instructions...........2

Product View ................4

Assembly ...................5

Operations ................6-7

Maintenance & Care .......8-9

Troubleshooting ............10

Warranty ....................11

Service ......................11

Contact Information .........11

Product Registration........12

Parts & Supplies ............12

Thanks again, from all of us
at BISSELL.

Mark J. Bissell
Chairman & CEO

www.BISSELL.ca

3

Product View

Dirt Container
Release Button

Empty

Cord Release

Model #

Cord

Power Brush Button

Power Button

Handle and Wand

Carry
Handle

Filters

Dirt
Container

Hose Connector

(when used as a Wand)

Handle
Height
Adjustment

Extra
Reach
Hose

Variable
Suction
Control

www.BISSELL.ca

4

Cord Release
and Storage

Twist Cord Release
down to quickly
remove cord

Post-Motor
Filter

PowerBrush

Main
Hose

Assembly

PowerBrush

WARNING

Do not plug in your vacuum until you are familiar with all instructions and operating
procedures.

1

Snap
TurboBrush
tool and clip
onto wand.

3

2

TM

“Click”

Insert Upper Handle
into Base, holding down
Height Adjustment
Lever until click sound
is heard.

4

ON / OFF

Extra
Reach
Hose

Power

ON / OFF

Snap lower cord wrap to lower back
of unit. Attach extra reach hose to
back of unit. Wrap power cord.

NOTE: Turn o the PowerBrush when vacuuming hard surfaces, such as hard

Plug into a polarized outlet
Recline vacuum and press Power Button

(O – OFF and l – ON)

wood or tiled floors, as well as when cleaning smaller rugs that may be caught by
the rotating brush.

NOTE: The Crevice Tool is stored inside the Extra Reach Stair Hose. Remove
the tool when the hose is in use and replace it inside the hose when ready to
store the Extra Reach Hose.

www.BISSELL.ca

5

Reclined
In Use

Upright
Locked
in Place

Upright
Locked
in Place

PowerBrush Switch

1

PowerBrush
ON / OFF

Power

Turn vacuum ON
before turning
ON PowerBrush.

Press brush side
of button to run
PowerBrush.

2

PowerBrush will not run when vacuum
is locked in upright position.

Adjusting the Variable Suction

1

2

Full
Suction

sucon control

Locate Variable Suction Control Valve. Twist counter-clockwise to reduce suction

NOTE: Some frieze carpets have long delicate fibers or threads that may be
damaged by rotating brush. Turn o the PowerBrush when cleaning this and
other similar types of carpet.

WARNING

Before using your vacuum, make sure that the dirt container is in locked position and
that all filters, both pre and post-filters are in place. DO NOT operate your vacuum without
these filters.

www.BISSELL.ca

6

for drapes, delicate surfaces, or thick/plush
carpet, etc.

Reduced
Suction

Above Floor Cleaning

Pull to

Disengage

Press Down

Pull to

Disengage

Press Down

1

Locate main hose connection on back of
vacuum, press lever and pull to unlock.

3

Press

Lift

4

2

Extra
Reach
Hose

Pull Extra Reach Hose off back of
vacuum and insert into Main Hose
connection.

Make sure latch is secured before
turning vacuum on.

Press down on Height
Adjustment Lever and
pull out Handle.

Connect Extra Reach Hose
to back of Handle, making
it a Wand.

Attach desired cleaning
tool to end of wand.

Parts & Supplies

For Parts and Supplies, go to www.BISSELL.ca and enter

your model number in the search field.

TurboBrush

www.BISSELL.ca

7

Maintenance: Emptying the Dirt Container

Press to Release

POWERGLIDE

POWERGLIDE

Pre-Motor
Filters

Checked pattern

when filter bottom

is dirty

Pre-Motor
Filters

Checked pattern

when filter bottom

is dirty

WARNING

To reduce the risk of electrical shock, turn power switch o and disconnect polarized plug
from electrical outlet before performing maintenance or troubleshooting checks.

1 2

Press
Release
Button

Maintenance: Cleaning the Dirt Container & Filters

Pull

Press Empty
Button

Pull handle
to push Dirt
Container away
from vacuum

Holding Dirt Container over a trash bin,
press Release Button on back.

Snap bottom back into place

1

Press

Press Empty
Button
and pull
away from
vacuum.

Twist top
right to
separate.

4

With dirt container removed,
press red release button to
access post-motor filter.

Clean all filters with mild
detergent, rinse, and squeeze all
excess water. Allow filters to dry
completely before reinserting.

Twist

Post-Motor
Filter

2

Rinse and dry all sections
of dirt container with
paper towel.

3

Remove pre-motor filters
and check for dirt on BOTH
sides. Separator Screen can
be rinsed and dried as well.

5 6

Place dry pre-motor filters back
on top of dirt container with
black tabbed side on top. Place
post-motor filter back to bottom
front of vacuum and snap filter
cover door back on.

Separator
Screen

When reassem­bling, place top
tank piece last
and twist left.

www.BISSELL.ca

8

Maintenance: Replace the Brush & Belt

End Cap

Align

Paddle Wheel

1

Unplug vacuum, turn over and
unscrew 7 Philips head screws
to remove bottom cover

2

Pull roller straight
out, threading
through belt

3

Replace roller and/or belt.
To reassemble roller, thread
through belt and line up End
Cap, then place bottom cover
back on and replace 7 screws.

Maintenance: Maintain the TurboBrush

TurboEraser

1 32

Slot

TurboBrush

Twist gray collar
counter-clockwise, until
slot appears, and then
separate faceplate

Carefully remove brush,
replace belt and brush,
if needed

TM

Tool

If paddle wheel gets dislodged,
align two clips on each side and
pop into place

Roller

Belt

Paddle Wheel End

Faceplate will not
close properly if all
parts are not aligned
correctly

*images may vary

Belt

TM

/

Clip

WARNING

Do not operate vacuum with damp or wet filters, as well as without filters or the Dirt
Container in place. Allow components to dry before reassembling the Dirt Container.

NOTE: If an object becomes lodged in foot and brush shuts o, turn vacuum
o and unplug from electrical outlet. Remove obstruction and brush will
automatically reset when vacuum is plugged and turned back on.

www.BISSELL.ca

9

Troubleshooting

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.

Problem Possible causes Remedies

PowerBrush
doesn’t
rotate

The PowerBrush power switch
is turned off

Vacuum is locked in upright
position

PowerBrush has lodged debris or
other entanglements, keeping the
brush from rotating

Make sure PowerBrush switch is on

Recline vacuum and switch on the
PowerBrush

Check the PowerBrush and
remove debris.

Vacuum
won’t pick
up dirt

Dirt is
escaping
from the
vacuum

Filters are dirty

The Main Hose is not connected Locate the Main Hose and reconnect

There is a crack or hole in the
Main Hose

The Power Brush bristles are worn Replace the PowerBrush

There is a clog in the vacuum Remove debris and any other

The Dirt Container is not seated
correctly

The Dirt Container is full Empty the Dirt Container

Filters are missing Check to see if all of the Pre-Motor

The Dirt Container is not seated
properly

Remove and rinse pre-motor and
post-motor filters. Allow enough
time for them to dry properly before
reinserting

by pushing the hose connection to
secure the latch

If there is a crack or hole, order a new
Main Hose from the BISSELL website

entanglements that may be
restricting its rotation

Press the Empty Button to release the
Dirt Container and reseat properly

and Post-Motor filters are in place

Press the Empty Button and remove the
Dirt Container. Insert the bottom first
and pivot the Dirt Container towards
the vacuum. Listen for a “click” sound,
indicating that it snapped into place

www.BISSELL.ca

10

Warranty

If you need additional instruction regarding
this warranty or have questions regarding
what it may cover, please contact BISSELL
Consumer Care by E-mail or telephone as
described below.

Limited Five-Year Warranty

Subject to the *EXCEPTIONS AND
EXCLUSIONS identified below, upon receipt
of the product BISSELL will repair or replace
(with new or remanufactured components
or products), at BISSELL’s option, free of
charge from the date of purchase by the
original purchaser, for five years any
defective or malfunctioning part.

See information below on "If your BISSELL
product should require service".

This warranty applies to product used for
personal, and not commercial or rental
service. This warranty does not apply to
fans or routine maintenance components
such as filters, belts, or brushes. Damage or
malfunction caused by negligence, abuse,
neglect, unauthorized repair, or any other
use not in accordance with the User's Guide
is not covered.

BISSELL IS NOT LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF
THIS PRODUCT. BISSELL’S LIABILITY WILL
NOT EXCEED THE PURCHASE PRICE OF
THE PRODUCT.

*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTIES
EITHER ORAL OR WRITTEN. ANY IMPLIED
WARRANTIES WHICH MAY ARISE
BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED
TO THE FIVE YEAR DURATION FROM
THE DATE OF PURCHASE AS DESCRIBED
ABOVE.

NOTE: Please keep your original sales receipt. It provides proof of date of
purchase in the event of a warranty claim.

Service

If your BISSELL product should require service:

Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about

your warranty, contact BISSELL Consumer Care.

Website:

www.BISSELL.ca

E-mail:

www.BISSELL.ca/email-us

Please do not return this product to the store.

Other maintenance or service not included in the manual should be
performed by an authorized service representative.

For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-263-2535.

Call:

BISSELL Consumer Care
1-800-263-2535
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET

www.BISSELL.ca

11

Register your product today!

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for
discounts and free shipping on
future purchases.

Faster Service

Supplying your information now
saves you time should you need to
contact us with questions regarding
your product.

Product Support Reminders
and Alerts

We’ll contact you with any
important product maintenance
reminders and alerts.

Special Promotions

Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!

Visit www.BISSELL.ca/registration now!

Visit the BISSELL website: www.BISSELL.ca

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

Parts & Supplies

For Parts and Supplies, go to www.BISSELL.ca and enter

your model number in the search field.

12

We c’t wait to ar from y!

Rate this product and let us (and millions

of your closest friends) know what you think!

www.BISSELL.ca

©2015 BISSELL Homecare, Inc
BISSELL Canada Corporation
Mississauga (Ontario) L5N 0B3
All rights reserved. Printed in China
Part Number 160-8163 Rev 09/15
Visit our website at: www.BISSELL.ca