Biostar iDEQ-T1 Setup Manual

iDEQ-T1 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. There is no guarantee that interference will not
occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here
and specially disclaims any implied warranties of merchantability or fitness for any
purpose. Further the vendor reserves the right to revise this publication and to make
changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining
the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will
not be responsible for any mistakes found in this user’s manual. All the brand and
product names are trademarks of their respective companies.

iDEQ-T1 Setup Manual

Table of Contents

Chapter 1: Introduction ..................................................................................... 1

Getting Started ............................................................................................. 1

Package Checklist ....................................................................................... 1

Specification ................................................................................................. 2

Getting to Know Your System ...................................................................... 3

Chapter 2: System hardware installation ........................................................ 4

Disassembling the Cover ............................................................................. 4

A. Installing WiFi Module ............................................................................. 5

C. Installing a 2.5 inch HDD ......................................................................... 6

VESA Bracket (Optional) .............................................................................. 7

Antenna (Optional) ....................................................................................... 8

Chapter 3: BIOS Setup ...................................................................................... 9

Main Menu .................................................................................................. 11

Advanced Menu ......................................................................................... 12

Chipset Menu ............................................................................................. 22

Security Menu ............................................................................................ 26

Performance Menu .................................................................................... 28

Boot Menu .................................................................................................. 30

Exit Menu ................................................................................................... 31

Chapter 4: BIOS Update & Software .............................................................. 32

BIOS Update .............................................................................................. 32

Software ..................................................................................................... 36

Chapter 5: Useful Help .................................................................................... 41

Driver Installation ....................................................................................... 41

Troubleshooting ......................................................................................... 42

Appendix: Specification In Other Languages ............................................... 43

Arabic ......................................................................................................... 43

French ........................................................................................................ 44

German ...................................................................................................... 45

Portuguese ................................................................................................. 46

Russian ...................................................................................................... 47

Spanish ...................................................................................................... 49

iDEQ-T1 Setup Manual

1

Chapter 1: Introduction

Getting Started

To assure the safe application of the mini PC, please carefully read the following:
 Before disassembling or cleaning this product, make sure the power

connector is unplugged.

 Keep the mini PC away from excessive moisture, direct sunlight, and

extreme heat and cold. Keep liquids away from the mini PC and keyboard.

 Never wipe the interior of the system with water or dip the system in water.
 Before connecting to any peripheral, please turn off the power of the

system.

Package Checklist

Please carefully unpack the mini PC and check the following items from the
package:

 mini PC x1
 Stand x1
 SATA Cable x1
 Screws Pack x1

 Power Cord x1

 Power Adaptor x1
 Quick Start Guide x1
 DVD Driver x1
 Rubber Stands x4
 Antenna x1

 VESA Mounting Kit x1

(optional)

 Wireless Module x1 (optional)

iDEQ-T1 Setup Manual

2

Specification

Processor

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

Graphics Integrated Intel® HD Graphics series graphic engine

Memory

Supports Dual Channel DDR3L 1333 (1.35V/1.5V)
2x DDR3L SO-DIMM Memory Slot, Max. Supports up to 16 GB Memory
Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L module
* Please refer to www.biostar.com.tw

for Memory support list.

Networking

LAN (RTL8111G) 1x Gigabit Ethernet, RJ-45 Port

WLAN (Wi-Fi module sold separately) 1x Mini PCIe Connector

Audio Realtek Codec ALC662, Support 2x Port with Line out / MIC in

Storage 1x SATA II connector, data transfer rates up to 3.0Gb/s

Rear I/O

DC jack (19V DC-in) 1x

USB 3.0 port 1x

USB 2.0 port 1x

RJ-45 Gigabit Lan port 1x

HDMI connector 1x

VGA connector 1x

Line-Out 1x

Mic-In 1x

Front I/O

USB 2.0 port 2x

Power on button 1x

Environment

Operation Temperature 0°C ~ 40°C (32°F ~ 100°F)

Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)

Relative Humidity 20% ~ 80% non-condensing

Power Supply 19V/45W

OS Support

Windows 7 / 8 / 8.1
Biostar reserves the right to add or remove support for any OS with or without notice.

Mounting

Foot stand

VESA 75/100 Mount Bracket (Optional)

Dimension 210mm (L) x 40mm (W) x 185mm (H)

Weight 0.8 kg

Regulatory

Compliance

CE/FCC

iDEQ-T1 Setup Manual

3

Getting to Know Your System

Front Panel

Rear Panel

iDEQ-T1 Setup Manual

4

Chapter 2: System hardware installation

Disassembling the Cover

1. Loosen four screws on the bottom cover, then turn the system over.

2. Place the tip of your fingernail into the tiny gap between the cover and the
chassis, then pull up the cover.

3. Loosen four screws of HDD Bracket.

iDEQ-T1 Setup Manual

5

4. After removing the HDD bracket, you will see the system board.

A. Installing WiFi Module

Insert WiFi module into mini PCIe slot and fasten screw. Connect antenna line to
“MAIN” on the WiFi module.

Note: Wi-Fi module sold separately

B. Installing Memory Module (1.35V/1.5V)

Insert memory module into SODIMM socket at backside of motherboard.

Note: The DIMM must be installed to DIMMA1 slot first.

iDEQ-T1 Setup Manual

6

C. Installing a 2.5 inch HDD

1. Fasten HDD bracket with HDD.

2. Connect the SATA cable to the HDD and system board.

3. Screw the HDD bracket back to the system.

iDEQ-T1 Setup Manual

7

VESA Bracket (Optional)

1. The mounting kit has either the VESA 75 mm or 100 mm mounting pattern.

2. Secure the VESA mounting bracket to your monitor with four screws.

3. Place your PC on VESA bracket and make sure the PC is hooked by the
VESA mounting bracket.

iDEQ-T1 Setup Manual

8

Antenna

Fasten antenna to the connector.

Note: After the system assembly, please place the rubber stand to each screw
hole.

iDEQ-T1 Setup Manual

9

Chapter 3: BIOS Setup

Introduction

The purpose of this manual is to describe the settings in the AMI UEFI BIOS
Setup program on this motherboard. The Setup program allows users to modify
the basic system configuration and save these settings to NVRAM.
UEFI BIOS determines what a computer can do without accessing programs
from a disk. This system controls most of the input and output devices such as
keyboard, mouse, serial ports and disk drives. BIOS activates at the first stage of
the booting process, loading and executing the operating system. Some
additional features, such as virus and password protection or chipset fine-tuning
options are also included in UEFI BIOS.
The rest of this manual will to guide you through the options and settings in UEFI
BIOS Setup.

Plug and Play Support

This AMI UEFI BIOS supports the Plug and Play Version 1.0A specification.

EPA Green PC Support

This AMI UEFI BIOS supports Version 1.03 of the EPA Green PC specification.

ACPI Support

AMI ACPI UEFI BIOS support Version 1.0/2.0 of Advanced Configuration and
Power interface specification (ACPI). It provides ASL code for power
management and device configuration capabilities as defined in the ACPI
specification, developed by Microsoft, Intel and Toshiba.

PCI Bus Support

This AMI UEFI BIOS also supports Version 2.3 of the Intel PCI (Peripheral
Component Interconnect) local bus specification.

DRAM Support

DDR3L SO-DRAM (Double Data Rate III Synchronous DRAM) is supported.

iDEQ-T1 Setup Manual

10

Using Setup

When starting up the computer, press <Del> during the Power-On Self-Test
(POST) to enter the UEFI BIOS setup utility.
In the UEFI BIOS setup utility, you will see General Help description at the top
right corner, and this is providing a brief description of the selected item.
Navigation Keys for that particular menu are at the bottom right corner, and you
can use these keys to select item and change the settings.

<Notice>

 The default UEFI BIOS settings apply for most conditions to ensure optimum performance of

the motherboard. If the system becomes unstable after changing any settings, please load the
default settings to ensure system’s compatibility and stability. Use Load Setup Default under
the Exit Menu.

 For better system performance, the UEFI BIOS firmware is being continuously updated. The

UEFI BIOS information described in this manual is for your reference only. The actual UEFI
BIOS information and settings on board may be slightly different from this manual.

 The content of this manual is subject to be changed without notice. We will not be responsible

for any mistakes found in this user’s manual and any system damage that may be caused by
wrong-settings.

iDEQ-T1 Setup Manual

11

Main Menu

Once you enter AMI UEFI BIOS Setup Utility, the Main Menu will appear on the
screen providing an overview of the basic system information.

BIOS Information

It shows system information including UEFI BIOS version, Product Name, Build
Date and etc.

Tota l M e mory

Shows system memory size, VGA shard memory will be excluded.

System Language

Choose the system default language.

System Date

Set the system date. Note that the ‘Day’ automatically changes when you set the
date.

System Time

Set the system internal clock.

iDEQ-T1 Setup Manual

12

Advanced Menu

The Advanced Menu allows you to configure the settings of CPU, Super I/O,
Power Management, and other system devices.

<Notice> Beware of that setting inappropriate values in items of this menu may cause system to

malfunction.

ACPI Settings

Enable ACPI Auto Configuration

This item enables or disables BIOS ACPI Auto Configuration.
Options: Disabled (Default) / Enabled

iDEQ-T1 Setup Manual

13

Enable Hibernation

This item enables or disables system ability to hibernate (OS/S4 Sleep State).
This option may be not effective with some OSes.
Options: Enabled (Default) / Disabled

ACPI Sleep State

This item selects the highest ACPI sleep state the system will enter when the
SUSPEND button is pressed.
Options: S3 only (Suspend to RAM) (Default) / Suspend Disabled

Lock Legacy Resources

The item enables or disables Lock of Legacy Resources.
Options: Disabled (Default) / Enabled

Restore AC Power Loss

Specify what state to go to when power is re-applied after a power failure.
Options: Power Off (Default) / Power On / Last State

EuP Control

When EuP is enabled, the system will meet EuP requirement.
Options: Disabled (Default) / Enabled

PME Wake up from S5

The item enables the system to wake from S5 using PME event.
Options: Enabled (Default) / Disabled

Wake system with Fixed Time

This item enables or disables the system to wake on by alarm event. When this
item is enabled, the system will wake on the hr::min::sec specified.
Options: Disabled (Default) / Enabled

Wake up date

You can choose which date the system will boot up.

Wake up hour / Wake up minute / Wake up second

You can choose the system boot up time, input hour, minute and second to
specify.

USB Device Wakeup from S3/S4

This item allows you to enable or disabled the USB resume from S3/S4 function.
Options: Disabled (Default) / Enabled

iDEQ-T1 Setup Manual

14

SMART FAN Control

System Smart Fan2

This item allows you to control the System Smart Fan function.
Options: Auto (Default) / Full Running

IT8627E H/W Monitor

iDEQ-T1 Setup Manual

15

Intel (R) Smart Connect Technology

ISCT Support

This item enables/disables ISCT Support.
Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the ISCT Support function to [Enabled]

ISCT Notification Control

Options: Enabled (Default)

CPU Configuration

This item shows CPU Information

Active Processor Cores

This item sets number of cores to enable in each processor package.
Options: All (Default) / 1

iDEQ-T1 Setup Manual

16

Limit CPUID Maximum

Disabled for Windows XP
Options: Disabled (Default) / Enabled

Execute-Disable Bit

XD can prevent certain classes of malicious buffer overflow attacks when
combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2,
SuSE Linux 9.2, Red Hat Enterprise 3 Update 3.).
Options: Enabled (Default) / Disabled

Hardware Prefetcher

This item enables or disables the Mid Level Cache (L2) streamer Prefetcher.
Options: Enabled (Default) / Disabled

Adjacent Cache Line Prefetch

This item enables or disables the Mid Level Cache (L2) prefetching of adjacent
cache lines.
Options: Enabled (Default) / Disabled

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided
by Vanderpool Technology
Options: Enabled (Default) / Disabled

Power Technology

This item enables or disables the power management features.
Options: Custom (Default) / Energy Efficient / Disable

EIST

This item enables or disables Intel SpeedStep.
Options: Enabled (Default) / Disabled

Turbo Mode

This item enables or disables Turbo Mode.
Options: Enabled (Default) / Disabled

P-STATE Coordination

This item changes P-STATE coordination type.
Options: HW_ALL (Default) / SW_ALL / SW_ANY

CPU C6 report

This item enables or disables CPU C6 (ACPI C3) report to OS.
Options: Enabled (Default) / Disabled

iDEQ-T1 Setup Manual

17

CPU C7 report

This item enables or disables CPU C7 (ACPI C3) report to OS.
Options: Enabled (Default) / Disabled

Package C State limit

This item sets Package C State limit.
Options: No Limit (Default) / C0 / C1 / C3 / C6 / C7

SATA Configuration

The BIOS will automatically detect the presence of SATA devices.

Serial-ATA (SATA)

This item enables/disables Serial ATA Device.
Options: Enabled (Default) / Disabled

SATA Mode

This item determines how SATA controller(s) operate.
Options: AHCI Mode (Default) / IDE Mode

SATA1

This item enables/disables Serial ATA Port1.
Options: Enabled (Default) / Disabled

iDEQ-T1 Setup Manual

18

Network Stack Configuration

Network Stack

This item enables or disables UEFI network stack
Options: Disabled (Default) / Enabled

Note: The following items appear only when you set the Network Stack function to [Enabled]

IPv4 PXE Support

This item enables or disables IPv4 PXE Boot Support. If disabled IPv4 booth
option will not be created.
Options: Enabled (Default) / Disabled

IPv6 PXE Support

This item enables or disables IPv6 PXE Boot Support. If disabled IPv6 booth
option will not be created.
Options: Enabled (Default) / Disabled

PXE boot wait time

Wait time to press ESC key to abort the PXE boot.

iDEQ-T1 Setup Manual

19

CSM Configuration

CSM Support

This item enables or disables CSM Support
Options: Enabled (Default) / Disabled

GateA20 Active

Upon Request – FA20 can be disabled using BIOS services. Always – do not
allow disabling GA20; this option is useful when any RT code is executed above
1MB
Options: Upon Request (Default) / Always

Option ROM Messages

This item sets the display mode for option ROM.
Options: Force BIOS (Default) / Keep Current

INT19 Trap Response

BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE – execute the
trap right away; POSTPONED – execute the trap during legacy boot.
Options: Postponed (Default) / Immediate

Boot option filter

This option controls what devices system can boot to.
Options: UEFI and Legacy (Default) / Legacy only / UEFI only

Network

This item controls the execution of UEFI and Legacy PXE OpROM
Options: Legacy only (Default) / Do not launch / UEFI only / Legacy first /
UEFI first

iDEQ-T1 Setup Manual

20

Storage

This item controls the execution of UEFI and Legacy Storage OpROM
Options: Legacy only (Default) / Do not launch / UEFI only / Legacy first /
UEFI first

Video

This item controls the execution of UEFI and Legacy Video OpROM
Options: Legacy only (Default) / Do not launch / UEFI only / Legacy first /
UEFI first

Other PCI device

It determines OpROM execution policy for devices other than Network, Storage,
or video.
Options: UEFI first (Default) / Legacy only

USB Configuration

Legacy USB Support

The item allows you to enable Legacy USB support. AUTO option disables
legacy support if no USB devices are connected. DISABLE option will keep USB
devices available only for EFI applications.
Options: Enabled (Default) / Disabled / Auto

XHCI Hand-off

This is workaround for OSes without XHCI hand-off support. The XHCI
ownership change should be claimed by XHCI driver.
Options: Enabled (Default) / Disabled

iDEQ-T1 Setup Manual

21

EHCI Hand-off

This is workaround for OSes without EHCI hand-off support. The EHCI
ownership change should be claimed by EHCI driver.
Options: Disabled (Default) / Enabled

USB Mass Storage Driver Support

The item allows you to enable or disable USB Mass Storage Driver Support.
Options: Enabled (Default) / Disabled

USB transfer time-out

The time-out value for Control, Bulk, and Interrupt transfers.
Options: 20 sec (Default) / 1 sec / 5 sec / 10 sec

Device reset time-out

The item sets USB mass storage device Start Unit command time-out.
Options: 20 sec (Default) / 10 sec / 30 sec / 40 sec

Device power-up delay

“Auto” uses default value: for a Root port it is 100ms, for a Hub port the delay is
taken from Hub descriptor.
Options: Auto (Default) / Manual
Note: The following items appear only when you set the Device power-up delay
function to [Manual]

Device power-up delay in seconds

Delay range is 1 ~ 40 seconds, in one second increments.
Options: 5 (Default)

iDEQ-T1 Setup Manual

22

Chipset Menu

This section describes configuring the PCI bus system. PCI, or Personal
Computer Interconnect, is a system which allows I/O devices to operate at
speeds nearing the speed of the CPU itself uses when communicating with its
own special components.

<Notice> Beware of that setting inappropriate values in items of this menu may cause system to

malfunction.

North Bridge

Integrated Graphics Device

Enable: Enable Integrated Graphics Device (IGD) when selected as the Primary
Video Adaptor. Disable: Always disable IGD.
Options: Auto (Default) / Disabled

iDEQ-T1 Setup Manual

23

IGD Turbo Enable

Enable: IGD Turbo Enable. Disable: IGD Turbo Disable.
Options: Enabled (Default) / Disabled

Primary Display

This item selects which of IGD/PCI Graphics device should be Primary Display.
Options: IGD (Default) / PCI

PAVC

This item enables/disables Protected Audio Video Control.
Options: LITE Mode (Default) / Disabled / SERPENT Mode

DVMT Pre-Allocated

This item selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used
by the Internal Graphics Device.
Options: 64M (Default) / 96M / 128M / 160M / 192M / 224M / 256M / 288M /
320M / 352M / 384M / 416M / 448M / 480M / 512M

DVMT Total Gfx Mem

This item selects DVMT5.0 Total Graphic Memory size used by the Internal
Graphics Device.
Options: 256MB (Default) / 128MB / MAX

Aperture Size

This item selects the Aperature Size.
Options: 256MB (Default) / 128MB / 512MB

GTT Size

This item selects the GTT Size.
Options: 2MB (Default) / 1MB

RC6 (Render Standby)

This item enables or disables render standby support.
Options: Enabled (Default) / Disabled

Max TOLUD

Maximum Value of TOLUD
Options: Dynamic (Default) / 1 GB / 1.25 GB / 1.5 GB / 1.75 GB / 2 GB /

2.25 GB / 2.5 GB / 2.75 GB / 3 GB

iDEQ-T1 Setup Manual

24

South Bridge

USB Configuration

XHCI Mode

This item enables or disables mode of operation of xHCI controller.
Options: Smart Auto (Default) / Auto / Enabled / Disabled

USB 2.0(EHCI) Support

This item controls the USB EHCI (USB2.0) functions. One EHCI controller must
always be enabled.
Options: Disabled (Default) / Enabled

iDEQ-T1 Setup Manual

25

USB Per Port Controller

This item controls each of the USB ports(0-3). Enable: Enable USB per port;
Disable: Use USB port x setting.
Options: Enabled (Default) / Disabled

USB Port 0/1/2/3

This item enables/disables USB port 0/1/2/3
Options: Enabled (Default) / Disabled

PCI Express Configuration

ASPM

This item sets PCI Express Active State Power Management settings.
Options: Auto (Default) / L0s / L1 / L0sL1 / Disabled

Speed

This item selects PCI Express port speed.
Options: Auto (Default) / Gen1 / Gen2

Onboard Lan

This item enables/disables the PCI Express Port 2 in the Chipset.
Options: Enabled (Default) / Disabled

Onboard LAN Option ROM

This item enables/disables Onboard LAN Option ROM.
Options: Disabled (Default) / Enabled

High Precision Timer

This item enables/disables the High Precision Event Timer.
Options: Enabled (Default) / Disabled

iDEQ-T1 Setup Manual

26

Security Menu

Administrator Password

This item sets Administrator Password.

User Password

This item sets User Password.

Secure Boot Menu

Secure Boot

Secure Boot flow control. Secure Boot can be enabled only when 1. Platform
Key (PK) is enrolled and Platform is operating in user mode and 2.CSM function
is disabled in Setup.
Options: Disabled (Default) / Enabled

iDEQ-T1 Setup Manual

27

Note: The following items appear only when you set the Secure Boot function to [Enabled]

Key Management

Enroll All Factory Default Keys

Forces system to user Mode – Install all Factory Default keys (PK, KEK, dbx,
dbt). Change takes effect after boot.

Platform Key (PK)

Delete PK – Allows you to delete the PK file from your system.
Set new PK – Allows you set new PK file.

Key Exchange Key Database (KEK)

Delete KEK – Allows you to delete the KEK file from your system.
Set new KEK – Allows you set new KEK file.
Append Var to KEK – Allows you append Var to KEK.

Authorized Signature Database (DB)

Delete DB – Allows you to delete the DB file from your system.
Set new DB – Allows you set new DB file.
Append Var to DB – Allows you append Var to DB.

Authorized TimeStamps (DBT)

Delete DB – Allows you to delete the DBT file from your system.
Set new DB – Allows you set new DBT file.
Append Var to DB – Allows you append Var to DBT.

Forbidden Signature Database (DBX)

Delete DBX – Allows you to delete the DBX file from your system.
Set new DBX – Allows you set new DBK file.
Append Var to DBX – Allows you append Var to DBX.

iDEQ-T1 Setup Manual

28

Performance Menu

This submenu allows you to change voltage and clock of various devices.
(However, we suggest you use the default setting. Changing the voltage and
clock improperly may damage the device.)

Notice

 Beware of that setting inappropriate values in items of this menu may cause system to

malfunction.

 The options and default settings might be different by RAM or CPU models.

DRAM Voltage

This item sets DRAM Voltage.
Options: Auto (Default) / 1.35V / 1.40V / 1.45V / 1.50V

DRAM Timing Select

This item sets DRAM Timing Select.
Options: Auto (SPD) (Default) / Manual

Note: The following items appear only when you set the DRAM Timing Select function to [Manual]

CAS# Latency (tCL)

This item allows you to select CAS Latency, Range 4-24
Options: Auto (Default)

RAS# to CAS# Delay (tRCD)

This item allows you to select Row Address to Column Address Delay, Range
3-20
Options: Auto (Default)

iDEQ-T1 Setup Manual

29

Row Precharge Time (tRP)

This item allows you to select Row Precharge Time, Range 3-15
Options: Auto (Default)

RAS# Active Time (tRAS)

This item allows you to select Row Active Time, Range 9-63
Options: Auto (Default)

Write Recovery Time (tWR)

This item allows you to select Internal Write to Read Command Delay, Range
5-16
Options: Auto (Default)

Row Refresh Cycle Time (tRFC)

This item allows you to select Minimum Refresh Recovery Time, Range 1-511
Options: Auto (Default)

Write to Read Delay (tWTR)

This item allows you to select Internal Write to Read Command Delay, Range
3-31
Options: Auto (Default)

Active to Active Delay (tRRD)

This item allows you to select Row Active to Row Active Delay, Range 4-15
Options: Auto (Default)

Read CAS# Precharge (tRTP)

This item allows you to select Read to Precharge Delay, Range 4-15
Options: Auto (Default)

Minimum CAS Write Latency Time

This item allows you to select Minimum CAS Write Latency Range, Range 5-12
Options: Auto (Default)

Four Active Window Delay (tFAW)

This item allows you to select Four Active Window Delay, Range 10-63
Options: Auto (Default)

iDEQ-T1 Setup Manual

30

Boot Menu

This menu allows you to setup the system boot options.

Setup Prompt Timeout

This item sets number of seconds to wait for setup activation key.
Options: 1 (Default)

Bootup NumLock State

This item selects the keyboard NumLock state.
Options: On (Default) / Off

Full Screen Logo Display

This item allows you to enable/disable Full Screen Logo Show function.
Options: Enabled (Default) / Disabled

BIOS Flash protection

While enabled, it can’t flash write and flash erase by SMI.
Options: Enabled (Default) / Disabled

Boot Success Beep

When this item is set to Enabled, BIOS will let user know boot success with
beep.
Options: Enabled (Default) / Disabled

Boot Option Priorities

The items specify the boot device priority sequence from the available devices.
The number of device items that appears on the screen depends on the number
of devices installed in the system.

iDEQ-T1 Setup Manual

31

Exit Menu

This menu allows you to load the optimal default settings, and save or discard
the changes to the BIOS items.

Discard Changes and Exit

Abandon all changes made during the current session and exit setup.

Save Changes and Reset

Reset the system after saving the changes.

Restore Defaults

This selection allows you to reload the BIOS when problem occurs during
system booting sequence. These configurations are factory settings optimized
for this system.

Launch EFI Shell from filesystem device

This item attempts to EFI Shell application (Shellx64.efi) from one of the
available filesystem devices.

Saving LAN driver to storage

Saving LAN driver to storage (WIN7_X86.EXE, WIN7_X64.EXE. Saving format
support FAT16/FAT32).

iDEQ-T1 Setup Manual

32

Chapter 4: BIOS Update & Software

BIOS Update

The BIOS can be updated using either of the following utilities:
 BIOSTAR BIOS Flasher: Using this utility, the BIOS can be updated from a file on a

hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM.

 BIOSTAR BIOS Update Utility: It enables automated updating while in the Windows

environment. Using this utility, the BIOS can be updated from a file on a hard disk, a
USB drive (a flash drive or a USB hard drive), or a CD-ROM, or from the file location
on the Web.

BIOSTAR BIOS Flasher

BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple
way to update your BIOS via USB pen drive.

Note1: This utility only allows storage device with FAT32/16 format and single partition.
Note2: Shutting down or resetting the system while updating the BIOS will lead to system boot

failure.

Updating BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, copy and save the BIOS file into a USB flash (pen) drive.

3. Insert the USB pen drive that contains the BIOS file to the USB port.

4. Power on or reset the computer and then press <F12> during the POST process.

5. After entering the POST screen,
the BIOS-FLASHER utility pops
out. Choose [fs0] to search for the
BIOS file.

iDEQ-T1 Setup Manual

33

6. Select the proper BIOS file, and a

message asking if you are sure to
flash the BIOS file. Click Yes to
start updating BIOS.

7. A dialog pops out after BIOS flash

is completed, asking you to restart
the system. Press the [Y] key to
restart system.

8. While the system boots up and the full screen logo shows up, press <DEL> key to
enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.

BIOS Update Utility (through the Internet)

1. Installing BIOS Update Utility from the DVD Driver.

2. Please make sure the system is connected to the internet before using this

function.

3. Launch BIOS Update Utility and
click the Online Update button on
the main screen.

iDEQ-T1 Setup Manual

34

4. An open dialog will show up to
request your agreement to start the
BIOS update. Click Yes to start the
online update procedure.

5. If there is a new BIOS version, the
utility will ask you to download it.
Click Yes to proceed.

6. After the download is completed,
you will be asked to program
(update) the BIOS or not. Click Yes
to proceed.

7. After the updating process is
finished, you will be asked you to
reboot the system. Click OK to
reboot.

8. While the system boots up and the full screen logo shows up, press <DEL> key
to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.

BIOS Update Utility (through a BIOS file)

1. Installing BIOS Update Utility from the DVD Driver.

2. Download the proper BIOS from http://www.biostar.com.tw/

3. Launch BIOS Update Utility and

click the Update BIOS button on
the main screen.

iDEQ-T1 Setup Manual

35

4. A warning message will show up
to request your agreement to start
the BIOS update. Click OK to start
the update procedure.

5. Choose the location for your BIOS
file in the system. Please select
the proper BIOS file, and then click
on Open. It will take several
minutes, please be patient.

6. After the BIOS Update process is
finished, click on OK to reboot the
system.

7. While the system boots up and the full screen logo shows up, press <DEL> key
to enter BIOS setup.
After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and
Reset to restart the computer. Then, the BIOS Update is completed.

Backup BIOS

Click the Backup BIOS button on
the main screen for the backup of
BIOS, and select a proper location
for your backup BIOS file in the
system, and click Save.

iDEQ-T1 Setup Manual

36

Software

Installing Software

1. Insert the Setup DVD to the optical drive. The driver installation program would
appear if the Auto-run function has been enabled.

2. Select Software Installation, and then click on the respective software title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process is completed, you will see the software icon showing on
the desktop. Double-click the icon to launch it.

Note1: All the information and content about following software are subject to be changed without
notice. For better performance, the software is being continuously updated.

Note2: The information and pictures described below are for your reference only. The actual
information and settings on board may be slightly different from this manual.

BIOScreen Utility

This utility allows you to personalize your boot logo easily. You can choose BMP as
your boot logo so as to customize your computer.

Please follow the step-by-step instructions below to update boot logo:

 Load Image：Choose the picture as the boot logo.
 Transform：Transform the picture for BIOS and preview the result.
 Update Bios：Write the picture to BIOS Memory to complete the update.

iDEQ-T1 Setup Manual

37

eHot-Line

eHot-Line is a convenient utility that helps you to contact with our Tech-Support
system. This utility will collect the system information which is useful for analyzing the
problem you may have encountered, and then send these information to our
tech-support department to help you fix the problem.

Note: Before you use this utility, please set Outlook Express as your default e-mail client
application program.

This block will show
the information which
wou ld be co llec ted in
the mail.

Pro vide t he e-ma il
address that you would
like to send the copy to.

Pro vide t he nam e of
the power supply
manufacturer and the
model no.

Send the mail out.

Save these infor mation to a .txt file

Exit this dialog.

Select your area or
the area close to you.

*

Pro vide t he name of
the memory module
manufactur er.

*

Describe condition
of your system.

*

*

repr esents important
in forma tion t hat yo u
must provide. Without
this information, you may
not be able to send out
the mail.

After filling up this information, click
“Send” to send the mail out. A
warning dialog would appear asking
for your confirmation; click “Send” to
confirm or “Do Not Send” to cancel.

If you want to save this information to
a .txt file, click “Save As…” and then
you will see a saving dialog appears
asking you to enter file name.

iDEQ-T1 Setup Manual

38

Enter the file name and then click
“Save”. Your system information will be
saved to a .txt file.

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

Note1: We will not share customer’s data with any other third parties, so please feel free to provide
your system information while using eHot-Line service.

Note2: If you are not using Outlook Express as your default e-mail client application, you may need
to save the system information to a .txt file and send the file to our tech support with other e-mail
application. Go to the following website http://www.biostar.com.tw/app/en/about/contact.php for
getting our contact information.

iDEQ-T1 Setup Manual

39

Smart Connect Technology

Intel® Smart Connect Technology is designed to update programs by periodically
waking your computer from sleep/standby mode for a short time. This function works
with applications that automatically get their data from the Internet.

System Requirement:

 Intel Smart Connect Technology enabled in BIOS Setup
 Set the “ACPI Sleep State” to S3 in BIOS Setup.
 Windows 7, Windows 8 and Windows 8.1
 Normal internet connection

Configuring Intel Smart Connect Technology

Step 1: After installing the operating system and motherboard drivers, install the Intel

Smart Connect Technology application. Restart your computer when completed.

Step 2: Click on start menu and input "regedit" in the search bar. Press enter to open
the registry editor. Look for the following directory in the registry editor:
Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Intel\Intel Smart Connect
Technology

Right-click on Intel Smart Connect Technology and select New > Key. Type “OEM”.

Note: Intel Smart Connect Technology is for S3 mode only. During the updating process, the
monitor will not light up and no sound will be output from the speaker.

Step 3: As shown in the screenshot below, right-click on OEM, select New >
Multi-String Value, and type “WhiteList”. Double-click WhiteList and type the
application name to be added in Edit Multi-String. For example, to add Microsoft Live
Mail, type “wlmail.exe”. Restart your computer when completed.

Step 4: After completing the steps above, go to Start\All Programs\Intel and launch
Intel(R) Smart Connect Technology.

iDEQ-T1 Setup Manual

40

Configuration Utility

The Intel Smart Connect Technology Configuration Utility allows configuration of the
sleep duration, extended hours sleep duration, and viewing of the Event History along
with other settings. To launch the application, select the application “Intel® Smart
Connect Technology in the Start menu (Windows* 7) or Start screen (Windows* 8/8.1)
to launch the configuration GUI. Once launched, the following is presented:

Note: For detailed setting of Intel® Smart Connect Technology, please check the below link.
http://www.intel.com/support/services/smartconnect/sb/CS-033109.htm

iDEQ-T1 Setup Manual

41

Chapter 5: Useful Help

Driver Installation

After you installed your operating system, please insert the Fully Setup Driver DVD
into your optical drive and install the driver for better system performance.
You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the
compatible driver for your motherboard and operating system. Click on each device
driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the
software available for your system, click on each software title to launch the
installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver DVD. Click on
the Manual icon to browse for available manuals.

Note1: If this window didn’t show up after you insert the Driver DVD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
Note2: You will need Acrobat Reader to open the manual file. Please download the latest version of
Acrobat Reader software from http://get.adobe.com/reader/
Note3: Intel(R) Trusted Execution Engine Interface Driver is only supported with Windows 8/8.1 &
Windows 7. For Windows 7 user, please install Microsoft Kernel-Mode Driver Framework (KMDF)
version 1.1. Otherwise, you found a yellow bang appears as "Intel Trusted Execution Engine
Interface" under system device manager. Also, you can follow the Microsoft instructions from the
link: KB2685811. http://support.microsoft.com/kb/2685811

iDEQ-T1 Setup Manual

42

Troubleshooting

Probable Solution

1. There is no power in the system.
Power LED does not shine; the fan of
the power supply does not work

2. Indicator light on keyboard does not
shine.

1. Make sure power cable is securely
plugged in.

2. Replace cable.

3. Contact technical support.

System is inoperative. Keyboard lights
are on, power indicator lights are lit, and
hard drives are running.

Using even pressure on both ends of

the DIMM, press down firmly until
the module snaps into place.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged in;
check the drive type in the standard
CMOS setup.

2. Backing up the hard drive is
extremely important. All hard disks
are capable of breaking down at
any time.

System only boots from an optical drive.
Hard disks can be read, applications can
be used, but system fails to boot from a
hard disk.

1. Back up data and applications files.

2. Reformat the hard drive. Re-install
applications and data using backup
disks.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

Review system’s equipment. Make

sure correct information is in setup.

System cannot boot after user installs a
second hard drive.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility with
other drives.

iDEQ-T1 Setup Manual

43

Appendix: Specification In Other Languages

Arabic

اﺞﻟﺎﻌﻤﻟا

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

ﺲﻜﻴﻓاﺮﺠﻟا ﺲﻜﻴﻓاﺮﺟ ﺔﻠﺴﻠﺳ ﻞﻐﺸﻣIntel® ﺔﻠﻣﺎﻜﺘﻤﻟا ﺔﻗﺪﻟا ﺔﻴﻟﺎﻋ

ةﺮآاﺬﻟا

ﺔﺟودﺰﻤﻟا ةﺎﻨﻘﻟا ﻢﻋﺪﻳDDR3L 1333 )1.35 ﺖﻟﻮﻓ /1.5 ﺖﻟﻮﻓ(

ةﺮآاذ ﺔﺤﺘﻓ2x DDR3L SO-DIMM ﻰﻟإ ﻞﺼﻳ ﺎﻣ ﻢﻋﺪﺗةﺮآاذ ،16 ﻰﺼﻗأ ﺪﺤآ ﺖﻳﺎﺑ ﺎﺠﻴﺟ

ﻞآDIMMﻢﻋﺪﺗnon-ECC 512 ﺖﻳﺎﺑﺎﺠﻴﻣ /1 /2 /4 /8 ةﺪﺣو ﺖﻳﺎﺑ ﺎﺠﻴﺟDDR3L

* ﻰﻟإ عﻮﺟﺮﻟا ﻰﺟﺮﻳwww.biostar.com.tw

اﺬﻟا ﻢﻋد ﺔﻤﺋﺎﻘﻟةﺮآ.

تﺎﻜﺒﺸﻟا

LAN (RTL8111G) ﺖﻳﺎﺑ ﺎﺠﻴﺟ ﺬﻔﻨﻣ ،ﺖﻧﺮﺜﻳإRJ-45 ×1

WLAN )ﻞﺼﻔﻨﻣ ﻞﻜﺸﺑ عﺎﺒﺗ يﺎﻓ ياو ةﺪﺣو( ﻞﺻﻮﻣPCIe ﺮﻐﺼﻣ×1

تﻮﺼﻟا Realtek ﺰﻴﻣﺮﺗALC662 ﺬﻔﻨﻣ ﻢﻋﺪﻳ ،×2 ﻂﺧ طﺮﺨﻣ ﻊﻣ /نﻮﻓﺮﻜﻴﻣ ﻞﺧﺪﻣ

ﻦﻳﺰﺤﺘﻟا ﻞﺻﻮﻣSATA II ×1 ﻰﻟإ ﻞﺼﺗ تﺎﻧﺎﻴﺑ ﻞﻘﻧ تﻻﺪﻌﻣ ،3.0 ﺖﻳﺎﺑﺎﺠﻴﺟ /ﺔﻴﻧﺎﺛ

I/O ﻲﻔﻠﺨﻟا

ﺮﻤﺘﺴﻣ رﺎﻴﺗ ﺬﻔﻨﻣ) ﺮﻤﺘﺴﻣ رﺎﻴﺗ ﻞﺧﺪﻣ19 ﺖﻟﻮﻓ( 1x

ﺬﻔﻨﻣUSB 3.0 1x

ﺬﻔﻨﻣUSB 2.0 1x

ﺬﻔﻨﻣLanRJ-45ﺖﻳﺎﺑﺎﺠﻴﺟ 1x

ﻞﺻﻮﻣHDMI 1x

ﻞﺻﻮﻣVGA 1x

ﻂﺨﻟا جﺮﺨﻣ 1x

نﻮﻓﺮﻜﻴﻣ ﻞﺧﺪﻣ 1x

I/O ﻲﻣﺎﻣﻷا

ﺬﻔﻨﻣUSB 2.0 2x

ﺔﻗﺎﻄﻟا ﻞﻴﻐﺸﺗ رز 1x

ﺔﺌﻴﺒﻟا

ﻴﻐﺸﺘﻟا ةراﺮﺣ ﺔﺟردﻞ

0 ﺔﻳﻮﺌﻣ ﺔﺟرد ~40 ﺔﻳﻮﺌﻣ ﺔﺟرد)32 ﺖﻳﺎﻬﻧﺮﻬﻓ ﺔﺟرد ~100

ﺖﻳﺎﻬﻧﺮﻬﻓ ﺔﺟرد(

ﻦﻳﺰﺨﺘﻟا ةراﺮﺣ ﺔﺟرد

-20 ﺔﻳﻮﺌﻣ ﺔﺟرد ~60 ﺔﻳﻮﺌﻣ ﺔﺟرد)-4 ﺖﻳﺎﻬﻧﺮﻬﻓ ﺔﺟرد ~

140 ﺖﻳﺎﻬﻧﺮﻬﻓ ﺔﺟرد(

ﺔﻴﺒﺴﻨﻟا ﺔﺑﻮﻃﺮﻟا 20 ٪ ~80ﻒﺛﺎﻜﺗ نود ٪

ﺔﻗﺎﻄﻟا دوﺰﻣ 19 ﺖﻟﻮﻓ /45 تاو

ﻞﻴﻐﺸﺘﻟا مﺎﻈﻧ ﻢﻋد

زوﺪﻨﻳو7 / 8 /8.1

رﺎﺘﺳﻮﻴﺑ ﺔآﺮﺷ ﻆﻔﺘﺤﺗ"Biostar" راﺬﻧإ ﻖﺑﺎﺳ نوﺪﺑ وأ ﻊﻣ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يأ ﻦﻋ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﻖﺤﻟﺎﺑ.

ﺐﻴآﺮﺘﻟا

ماﺪﻗﻷا ﻞﻣﺎﺣ

ﺐﻴآﺮﺗ ﻞﻣﺎﺣVESA 75/100 )يرﺎﻴﺘﺧا(

دﺎﻌﺑﻷا 210 ﻢﻣ)لﻮﻃ ( ×40 ﻢﻣ)ضﺮﻋ ( ×185 ﻢﻣ)عﺎﻔﺗرا(

نزﻮﻟا 0.8 ﻢﺠآ

ﻲﻤﻴﻈﻨﺘﻟا ﻖﻓاﻮﺘﻟا CE/FCC

iDEQ-T1 Setup Manual

44

French

Processeur

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

Graphique Intégré Intel® HD Série Graphique Moteur Graphique

Mëmoire

Soutient Canal double DDR3L 1333 (1.35V/1.5V)
2x DDR3L SO-DIMM Créneau de Mémoire, Max. Supporte jusqu’à 16 GB de
Mémoire
Chaque DIMM supporte non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L Module
* Référez-vous s’il vous plaît à www.biostar.com.tw pour la liste de soutien de

mémoire.

Circuit

LAN (RTL8111G) 1x Gigabit Ethernet, RJ-45 Port

WLAN (Wi-Fi module vendu séparément) 1x Mini PCIe Connecteur

Audio Realtek Codec ALC662, Soutient 2x Port avec Line-sortie / MIC-entrée

Stockage 1x SATA II connecteur, taux de transfert de données jusqu’à 3.0Gb/s

Arrière I/O

DC Jack (19V DC-in) 1x

USB 3.0 Port 1x

USB 2.0 Port 1x

RJ-45 Gigabit Lan Port 1x

HDMI Connecteur 1x

VGA Connecteur 1x

Line-sortie 1x

Mic-entrée 1x

Avant I/O

USB 2.0 Port 2x

Bouton de Puissance 1x

Milieu

Température de Fonctionnement 0°C ~ 40°C (32°F ~ 100°F)

Température de Stockage -20°C ~ 60°C (-4°F ~ 140°F)

Humidité Relative 20% ~ 80% Sans Condensation

Alimentation
Électrique

19V/45W

OS Soutien

Windows 7 / 8 / 8.1
Biostar se réserve le droit de ajouter ou de supprimer du support OS avec ou sans
notification.

Fixation

Support de Pie

VESA 75/100 Support de Fixation (Optional)

Dimensions 210mm (Longeur) x 40mm (Largeur) x 185mm (H)

Poids 0.8 kg

Conformité à la
réglementation

CE/FCC

iDEQ-T1 Setup Manual

45

German

Prozessor

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

Grafik Integrierter Intel® HD Grafik Serie grafischer Motor

Speicher

Unterstützt Doppelkanal DDR3L 1333 (1.35V/1.5V)
2x DDR3L SO-DIMM Speicher Schlitz, Max. Unterstützt bis 16 GB Speicher
Jeder DIMM unterstützt non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L Modul
* Bitte konsultieren Sie www.biostar.com.tw für die Unterstützungsliste des
Speichers.

Netzwerk

LAN (RTL8111G)

1x Gigabit Ethernet, RJ-45
Anschluss

WLAN (Wi-Fi Modul wird separat verkauft) 1x Mini PCIe Steckverbinder

Audio Realtek Codec ALC662, Unterstützung 2x Anschluss mit Line out / MIC in

Lager 1x SATA II Steckverbinder, Daten Übertragungsrate bis zu 3.0Gb/s

Rückseite I/O

DC Klinkenstecker (19V DC-in) 1x

USB 3.0 Anschluss 1x

USB 2.0 Anschluss 1x

RJ-45 Gigabit Lan Anschluss 1x

HDMI Steckverbinder 1x

VGA Steckverbinder 1x

Line-Out 1x

Mic-In 1x

Forderseite I/O

USB 2.0 Anschluss 2x

Leistung auf Taste 1x

Umgebung

Betriebstemperatur 0°C ~ 40°C (32°F ~ 100°F)

Lagertemperatur -20°C ~ 60°C (-4°F ~ 140°F)

Relative Luftfeuchtigkeit 20% ~ 80% nicht kondensierend

Netzteil 19V/45W

OS Unterstützung

Windows 7 / 8 / 8.1
Biostar behält sich das Recht vor Unterstützung hin zu fügen oder zu entfernen für
jede OS mit oder ohne Ankündigung.

Befestigung

Fußstand

VESA 75/100 Befestigungsklammer (Fakultativ)

Größe 210mm (L) x 40mm (B) x 185mm (H)

Gewicht 0.8 kg

Regulierungsbeac
htung

CE/FCC

iDEQ-T1 Setup Manual

46

Portuguese

Processador

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

Gráficos Motor gráfico Intel® da série HD Graphics integrado

Memória

Suporta Canal Duplo DDR3L 1333 (1.35V/1.5V)
Ranhura de Memória 2x DDR3L SO-DIMM, Max. Suporta até 16 GB de memória
Cada DIMM suporta módulo não-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L
* Por favor, refira awww.biostar.com.tw

para a lista de suporte de memória.

Rede

LAN (RTL8111G) 1x Gigabit Ethernet, Porta RJ-45

WLAN (Módulo Wi-Fi vendido
separadamente)

1x Mini Conector PCIe

Áudio Realtek Codec ALC662, Suporta 2x Portas com Line out / MIC in

Armazenamento 1x conector SATA II, transferência de dados até 3.0Gb/s

I/O Traseiro

Porta DC (19V DC-in) 1x

Porta USB 3.0 1x

Porta USB 2.0 1x

Porta RJ-45 Gigabit Lan 1x

Conector HDMI 1x

Conector VGA 1x

Line-Out 1x

Mic-In 1x

I/O Frontal

Porta USB 2.0 2x

Botão de Power on (Ligar) 1x

Ambiente

Temperatura de Funcionamento 0°C ~ 40°C (32°F ~ 100°F)

Temperatura de Armazenamento -20°C ~ 60°C (-4°F ~ 140°F)

Humidade Relativa 20% ~ 80% não condensante

Fonte de
Alimentação

19V/45W

Assistência de SO

Windows 7 / 8 / 8.1
A Biostar reserva-se ao direito de adicionar ou retirar a assistência para qualquer SO,
com ou sem aviso prévio.

Montagem

Pés de apoio

Suporte de montagem VESA 75/100 (Opcional)

Dimensões 210mm (C) x 40mm (L) x 185mm (A)

Peso 0.8 kg

Conformidade
Regulamentar

CE/FCC

iDEQ-T1 Setup Manual

47

Russian

Процессор

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

Графики Интегрированные Intel® HD графики серии графического процессора

Память

Поддерживает Двойной канал DDR3L 1333 (1.35V/1.5V)
2xDDR3L SO-DIMM Слот памяти, макс. поддерживает до 16Гб памяти
Каждый DIMM (модуль памяти с двухрядным расположением выводов)
поддерживает не-ECC 512Мб/ 1/ 2/ 4/ 8 Гб DDR3L модуля

* Для перечня поддержания памяти смотрите www.biostar.com.tw

.

Вычислительная
сеть

LAN (RTL8111G) 1xГигаб ит Ethernet, RJ-45 порт

WLAN (Wi-Fi модуль продается
отдельно)

1x Мини PCIe соединитель

Аудио

Realtek Codec ALC662, поддерживает 2 x порта с Line out (Выход Линии) / MIC in
(вход Микрофона)

Запоминающее
устройство

1x SATA II соединитель, скорость передачи данных до 3.0Гб/сек.

Задние
Вход/Выход I/O

Гнездо постоянного тока DC (19V DC-in
вход)

1x

USB 3.0 порт 1x

USB 2.0 порт 1x

RJ-45 Гигабит Lan порт 1x

HDMI соединитель 1x

VGA соединитель 1x

Line-Out (Выход линии) 1x

Mic-In (Вход микрофона) 1x

Передние
Вход/Выход
I/O

USB 2.0 порт 2x

Кнопка включения 1x

Усл ови я работы

Рабочая температура 0°C ~ 40°C (32°F ~ 100°F)

Температура хранения -20°C ~ 60°C (-4°F ~ 140°F)

Относительная влажность 20% ~ 80% неконденсирующаяся

Электропитание 19V/45W

OS Поддержка

Windows 7 / 8 / 8.1
Biostar оставляет за собой право добавлять или удалять поддержку любой ОС с

или без предварительного уведомления.

Уст ан овк а

Подставка для ног

VESA 75/100 Кронштейн (по выбору)

Размеры 210мм (Д) x 40мм (Ш) x 185мм (В)

Вес 0.8 кг

Соблюдение
нормативных
требований

CE/FCC

iDEQ-T1 Setup Manual

48

Japanese

プロセッサ

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

グラフィックス Integrated Intel® HD グラフィックス シリーズ グラフィック エンジン

メモリ

デュアル チャンネル DDR3L 1333 (1.35V/1.5V) 対応
2x DDR3L SO-DIMM メモリ スロットは、メモリ最大16 GBまで対応
各 DIMM はnon-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L モジュール対応

* www.biostar.com.tw

にリンクし、 メモリ対応リストを取得してください。

ネットワーク

LAN (RTL8111G)

1x ギガバイト イーサネット、
RJ-45 ポート

WLAN (Wi-Fi モジュール別売) 1x Mini PCIe コネクタ

オーディオ Realtek Codec ALC662、 2x ポート ラインアウト/マイク入力対応

保存 1x SATA II コネクタ、データ転送速度は最大 3.0Gb/s まで対応

リア I/O

DC ジャック(19V DC-in) 1x

USB 3.0 ポート 1x

USB 2.0 ポート 1x

RJ-45 ギガバイト Lan ポート 1x

HDMI コネクタ 1x

VGA コネクタ 1x

ラインアウト 1x

マイク入力 1x

フロント I/O

USB 2.0 ポート 2x

パワーオン・ボタン 1x

環境

操作 温度 0°C ~ 40°C (32°F ~ 100°F)

保存 温度 -20°C ~ 60°C (-4°F ~ 140°F)

相対 湿度 20% ~ 80%非結露

電源装置 19V/45W

OS 対応

Windows 7 / 8 / 8.1
Biostar は事前の予告無しに全ての OS に対する追加または削除する権利を留保しま

す

据え付け

蹄摺台

VESA 75/100 マウントブラケット(オプション)

寸法 210mm (L) x 40mm (W) x 185mm (H)

重量 0.8 kg

規制対応 CE/FCC

iDEQ-T1 Setup Manual

49

Spanish

Procesador

iDEQ-T1 IN2940T1: Intel® Celeron® Processor N2940 (2M Cache, up to 2.25 GHz)
iDEQ-T1 IJ1800T1: Intel® Celeron® Processor J1800 (1M Cache, up to 2.58 GHz)

Gráfico Serie de Intel ® HD Gráfico motor gráfico integrado

Memoria

Sportar Canal Dual DDR3L 1333 (1.35V/1.5V)

Muesca de Memoria 2x DDR3L SO-DIMM, Soportar Memoria Max. de 16 GB

Cada DIMM soporta modulo non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3L

Por favor refiere la www.biostar.com.tw

para la lista de soporte de Memoria.

Interconexión

LAN (RTL8111G) 1x Gigabit Ethernet, Puerto RJ-45

WLAN (se vende por separado el modulo
de Wi-Fi)

1x Mini PCIe Conector

Audio Realtek Codec ALC662, Soportar 2x Puerto con Línea out / MIC in

Almacenaje 1x SATA II conector, tarifa de transferir datos hasta 3.0Gb/s

I/O Trasero

DC gato (19V DC-in) 1x

Puerto de USB 3.0 1x

Puerto de USB 2.0 1x

RJ-45 Gigabit Lan puerto 1x

HDMI conector 1x

VGA conector 1x

Línea-Out 1x

Mic-In 1x

I/O Delantero

Puerto de USB 2.0 2x

Botón de Potencia On 1x

Ambiente

Temperatura de Operación 0°C ~ 40°C (32°F ~ 100°F)

Temperatura de Almacenaje -20°C ~ 60°C (-4°F ~ 140°F)

Humedad Relativa 20% ~ 80% no-condensación

Suministro de
Potencia

19V/45W

Soportar OS

Windows 7 / 8 / 8.1

Biostar reserva el derecho de añadir o quitar el soporte a cualquier OS con o sin
aviso.

Montaje

Soporte de pie

VESA 75/100 Anaquel de Montaje (Opcional)

Dimensión 210mm (L) x 40mm (W) x 185mm (H)

Peso 0.8 kg

Cumplimiento de
Regulador

CE/FCC

2014/08/25