Biostar H61MGV, H61MHV, H61MLC2 Owner's Manual
H61MHV/H61MGV/H61MLC2 Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment ge nerates, uses, and can radiate radio frequency
energy and, if not i nstalled and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Dichiar azione di conformit à
sintetica
Ai s ensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short De cla ration of conf ormity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as s pecified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1 Before You Start......................................................................................... 1
1.2 Package Checklist ..................................................................................... 1
1.3 Motherboard Features .............................................................................. 2
1.4 Rear Panel Connectors.............................................................................. 3
1.5 Motherboard Layout ................................................................................. 4
Chapter 2: Hardware Installation .......................... 5
2.1 Installing Central Processing Unit (CPU) ............................................... 5
2.2 FAN Headers .............................................................................................. 7
2.3 Installing System Memory ........................................................................ 8
2.4 Connectors and Slots................................................................................ 10
Chapter 3: Headers & Jumpers Setup .................. 13
3.1 How to Setup Jumpers............................................................................. 13
3.2 Detail Settings .......................................................................................... 13
Chapter 4: Useful Help ........................................ 16
4.1 Driver Installation Note .......................................................................... 16
4.2 Software .................................................................................................... 17
4.3 Extra Information .................................................................................... 21
4.4 AMI BIOS Beep Code ............................................................................... 22
4.5 Troubleshooting ....................................................................................... 23
Appendix: SPEC In Other Languages ................... 24
German .................................................................................................................. 24
French .................................................................................................................... 26
Italian..................................................................................................................... 28
Spanish ................................................................................................................... 30
Portugue se ............................................................................................................ 32
Polish ...................................................................................................................... 34
Russian ................................................................................................................... 36
Arabic..................................................................................................................... 38
Japanese ................................................................................................................ 40
H61MHV/H61MGV/H61MLC2
CHAPTER 1: INTRODUCTION
1.1 B
EFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be
0 to 45 degrees Celsius.
1.2 PACKAGE CHECKLIST
Serial ATA Cable x2
Rear I/O Panel for ATX Case x1
Installation Guide x1
Fully Setup Driver DVD x1
NOTE: The package contents may be different due to area or your motherboard version.
1
Motherboard Manual
/
1.3 MOTHERBOARD FEATURES
SPEC
CPU
Chipset
Super I/O
Main
Memory
SATA 2
LAN
Socket 1155
Int e l Core i7 / i5 / i3 / Pent ium / Celeron
processor
Int e l H6 1
IT8772E
Prov ides the most commonly us ed legacy
Super I/O functionality
Low Pin Count Interface
DDR3 DIMM Slots x 2
Max Memory Capacity 16GB
Each DIMM supports 512MB/
1GB/2GB/4GB/8GB DDR3
Integrated Serial ATA Controller
RTL8111F (H61MHV & H61 MGV)
RTL8105E (H61MLC2)
Supports Execute Disab le B it / Enhanced Inte l
SpeedSt ep® / Intel Ar ch itecture- 64 / Ext ended
Memory 64 Technology / Virtualization Technology
Hyper Threading
En v ironm en t Cont rol init iatives
Hardware Monitor Controller
Fan Sp eed Controller
ITE's "S mart Guard ian" function
Dual Channel Mode DDR3 me mory mo du le
Supports DDR3 1066 / 1333
Supports DDR3 1600 (depending on CPU)
Register ed DIMM and ECC D IMM is not supported
Data transfer rates up to 3.0 Gb/s
SATA Version 2.0 s p e c if icat ion co mpliant
10 / 100 / 1000 Mb/s auto negotiation
10 / 100 Mb/s auto negot iation
Sound
Codec
Slots
On Board
Connectors
2
ALC662
PCI-E Gen3x16 slot x1
(depe nd ing on CPU)
PCI-E Gen2 x1 slot x1 Supports PCI-E Gen2 x1 expansion card
SATA2 Connecto r x4 Each connector suppo rts 1 SATA2 device
Front Panel Connector x1 Supports front panel facilities
Front Audio Connector x1 Supports front panel audio function
CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)
System Fan Header x1 System Fan Power supply
Clear CMOS Head er x1 Restore CMOS dat a to fact ory def au lt
5.1 channels audio out
High Definition Audio
Supports PCI-E Gen2/3 x16 expansion card
H61MHV/H61MGV/H61MLC2
SPEC
USB2.0 Connector x2 Each co nnector supports 2 front panel USB2.0 po rts
Serial Port Connector x1 Connects to RS-232 Port
Power Connector (24pin) x1 Connects to Power supp ly
Power Connector (4pin) x1 Connects to Power supply
PS/2 Keyboard x1
PS/2 Mous e x1
Rear Panel
I/O
Board Size
OS Support
HDMI Port (H61MHV) x1
VGA Port x1
LAN port x1
USB2.0 Port x4
Audio Jack x3
170 (W) x 226 (L) mm
Windows XP / Vista / 7
1.4 REAR PANEL CONNECTORS
Connects to PS/2 Keybo ard
Connects to PS/2 Mouse
Connects to HDMI Display
Connect to D-SUB monitor
Connect to RJ-45 ethernet cable
Connect to USB2.0 devices
Provide Audio-In/Out and Mic. Connection
Biostar reserves the r ight to add or remove support
for any OS with or without notice
NOTE:
z HDM I/ VGA Output req uire a n Intel Core famil y processor wit h Intel Grap hics Technology.
z Maximum resolution:
VGA: 2048 x 1536 @75Hz
HDMI: 1920 x 1200 @60Hz (for H61MHV only)
z The H61MHV supports dual video outputs, but the HDMI is not supported under DOS and
BIOS set up.
3
Motherboard Manual
1.5 MOTHERBOARD LAYOUT
NOTE: ■ represents the 1st pin.
4
H61MHV/H61MGV/H61MLC2
CHAPTER 2: HARDWARE INSTALLATION
2.1 I
NSTALLING CENTRAL PROCESSING UNIT (CPU)
Notice:
1. Remove Pin Cap before installa tion, and make good preservation for future use.
When the CPU is removed, cover the Pin Cap on the e mpty socket to ensure pin
legs wo n’t be damaged.
2. The motherboard might equip with two different types of pin cap. Please refer
below instruction to remove the pin cap.
Step 1: Pull the socket locking lever out from the socket then raise the
lever and load plate to the fully open position.
Step 2: Remove the Pin Cap.
5
Motherboard Manual
Step 3: Hold processor with your thumb and index fingers, oriented as
shown. Align the notches with the socket. Lower the processor
straight down without tilting or sliding the processor in the socket.
Step 4: Close the load plate. Pressing down on the load plate, close and
engage the socket lever.
Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the CPU_FAN1 to complete the installation.
6
H61MHV/H61MGV/H61MLC2
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
SYS_FAN1: System Fan Header
Assignment
Pin
1 Ground
2 +12V
3
FAN RPM rate sense
4 Smart Fan Control
Pin
Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
Note:
The SYS_FAN1 support 3-pin head connectors; the CPU_FAN1 supports 4-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.
7
Motherboard Manual
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
8
H61MHV/H61MGV/H61MLC2
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
Note:
If the DIMM does not go in smoothly, do not force it. Pull it all the way out
and try again.
B. Memory Capacity
DIMM Socket
Location
DDR3_A1 512MB/1GB/2GB/4GB/8GB
DDR3_B1 512MB/1GB/2GB/4GB/8GB
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status
Disabled O X
Disabled X O
Enabled O O
(O means memory installed; X, not installed.)
The DRAM bus width of the memory module must be the same(x8 or
x16)
DDR3 Module
DDR3_A1
Total Mem o ry
Size
Max is 16GB.
DDR3_B1
9
Motherboard Manual
2.4 CONNECTORS AND SLOTS
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA2 interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
ATXP W R2: AT X P ower Source Connector
This connector provides +12V to CPU power circuit.
Pin
Pin
Assignment
1 Ground
2 TX+
3 TX4 Ground
5 RX-
6 RX+
7 Ground
Assignment
1 +12V
2 +12V
3 Ground
4 Ground
10
H61MHV/H61MGV/H61MLC2
ATXP W R1: AT X P ower Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
11
Loading...