Page 1
MODEL BAP2000
BAP2001
PERMAtech
™
ionizing
air cleaner
with
Read instructions before
operating. Retain for
future reference.
Instruction
Leaflet
INFO-LINE
If after having read this leaflet, you have any
questions or comments on your air cleaner,
call 1-800-253-2764 in North America.
☎
9100040001773
BAP2000/200105EM1
HMAN001.05.US.OM1
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 1
Page 2
AIR CLEANER SAFETY
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
• Read all instructions before using the appliance.
•To avoid fire or shock hazard, plug the air cleaner and
Galileo
®
Wireless Air Quality Center directly into a 120V AC
electrical outlet.
• If the filter is covered by a bag when shipped: Remove
plastic bag before use.
• Keep the cord out of heavy traffic areas. To avoid fire hazard, NEVER put the cord under rugs, near heat registers,
radiators, stoves, or heaters.
•To protect against electrical hazards, DO NOT immerse in
water or other liquids. Do not use near water.
•Close supervision is necessary when any appliance is used
by or near children, or disabled persons.
• Always unplug the air cleaner before moving it, opening the grill,
changing the filters, cleaning, or whenever the air cleaner is not
in use. Be sure to pull by the plug and not the cord.
• NEVER drop or insert any object into any openings.
• DO NOT operate any appliance with a damaged cord or
plug, if motor fan fails to rotate, after the appliance malfunctions, or if it has been dropped or damaged in any manner.
Return appliance to manufacturer for examination, electrical
or mechanical adjustment, or repair.
• Use appliance only for intended household use as
described in this manual. Any other use not recommended
by the manufacturer may cause fire, electric shock, or injury
to persons. The use of attachments not recommended or
sold by The Holmes Group may cause hazards.
• DO NOT use outdoors.
• NEVER block the air openings, grills/outlets or place on a
soft surface such as a bed or sofa, as this could cause the
unit to tip over, thus blocking the Air Intake Opening/Grill.
• Keep unit away from heated surfaces and open flames.
• Galileo
®
Wireless Air Quality Center should only be used in
a room with temperatures between 40
o
F and 110 oF.
• DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void serv-
2
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 3
Page 3
3
iceable parts. All servicing should be performed by qualified
personnel only.
•WARNING: To reduce the risk of fire or electric shock, DO NOT
use this air cleaner with any solid-state speed control device.
• DO NOT place anything on top of unit.
• The ionizer may cause a static charge to build up on the air
output grill. A static-charged electric shock may be felt if the
unit is not properly grounded. To avoid a shock, plug the
unit's three-prong plug into a grounded outlet, or properly
install a ground adapter as described in this manual.
The shock will not occur if the ionizer is off.
RADIO FREQUENCY COMPLIANCE INFORMATION
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Modifications not authorized by the manufacturer may void
user’s authority to operate this device.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS PRODUCT IS EQUIPPED
WITH A 3-PRONG PLUG.
This product is for use on
120 volts.
The cord has a plug (A) as
shown. An adapter (C) is
available for connecting
three-blade grounding-type
plugs to two-slot receptacles (B). The green grounding plug
extending from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. The adapter
should not be used if a three-slot grounded receptacle is
available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY.
CORD AND PLUG INSTALLATION SAFETY
INSTRUCTIONS
The length of cord used on this appliance was selected to reduce
the hazards of becoming tangled in, or tripping over a longer
WARRANTY
The manufacturer warrants to the first retail purchaser, for
FIVE ( 5 ) YEARS from the date of original purchase, either
to repair or replace at its option, without charge (parts and
labor), any supplied or manufactured part of this air cleaner
which, upon inspection by an authorized service center,
proves to have failed in normal use due to defects in material or workmanship, or at its option, to replace the unit.
Operation under conditions other than those recommended
at voltages other than the voltage indicated on the unit,or
any attempts by unauthorized personnel to service the unit
or modify it, will render the guarantee void.
The manufacturer shall not be liable for any personal injury,
propertydamage or any incidental or consequential damages of
any kind, resulting from defects, malfunctions, misuse, improper
installation or alteration of the product.
THE MANUFACTURER EXPRESSLY DISCLAIMS ALL
RESPONSIBILIT YFOR CONSEQUENTIAL DAMAGES
OR INCIDENTALL OSSES CAUSED BY USE OF THIS
PRODUCT.
The provisions of this Warranty are in addition to, and not a
modification of, or subtraction from the statutory warranties
and other rights and remedies contained in any applicable
legislation and to the extent that any such provision purports
to disclaim, exclude or limit any such statutory warranties or
other rights or remedies, such provisions shall be deemed to
be amended to the extent necessary to comply therewith.
For Warranty Service, please call 1-800-253-2764 in
North America.
A Bionaire®consumer service representative will help determine which is the best procedure in order for your air
cleaner to be repaired.
KEEP THIS NUMBER FOR FUTURE REFERENCE.
The Holmes Group, Inc.
Consumer Service Department
13052 Jurupa Avenue
Fontana, CA 92337
14
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 5
Page 4
AIR CLEANER SERVICE INSTRUCTIONS
1. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void the
warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed by
qualified personnel only.
2. If you need to exchange the unit, please return it in its
original carton, with a sales receipt, to the store where
you purchased it. If you are returning the unit more than
30 days after the date of purchase, please see the
enclosed warranty.
3. Should your Air Cleaner require service, please call
1-800-253-2764 in North America for further assistance.
A return authorization will be given when you call.
4. If you have any other questions or comments,
feel free to write to us:
The Holmes Group, Inc.
Consumer Service Department
13052 Jurupa Avenue
Fontana, CA 92337
Visit our website at www.bionaire.com
Bionaire
®
, the Bionaire logo®, Galileo
®
, the Galileo logo™ and
PERMAtechTMare trademarks of The Holmes Group, Inc. or
its subsidiary.
13
cord. If a longer cord is necessary, an approved extension
cord may be used. The electrical rating of the extension cord
must be equal to or greater than the rating of the air cleaner.
Care must be taken to arrange the extension cord so that it
will not drape over the countertop or tabletop where it can be
pulled on by children or accidentally tripped over.
Thank you for choosing a Bionaire
®
air cleaner. To ensure the
best performance from your air cleaner, please read and save
the following instructions.
IONIZER
Your Air Cleaner has an independently controlled ionizer, which,
when turned on, releases negative ions into outgoing filtered
air. Ions are tiny particles that carry a positive or negative
charge. These ions exist naturally around us, in the air, water
and the ground. Both positive and negative ions are colorless,
odorless and completely harmless. Negative ions help the air
purification process by attaching themselves to very small
airborne particles in the room.
These particles take on a negative charge and may join with
positively charged particles such as dust, pollen, smoke and pet
dander to form larger particles that are then more readily captured
by the filter system, or they may be attracted to positively
charged surfaces like walls or floors.
You may also note after extended use, that dust may have
collected around the grills or front panel. This is from the
ionization affect caused by the negative ions exiting from the
air outlet. This is additional evidence of the air cleaning
effectiveness of negative ions. The dust can be easily removed
with a clean, damp cloth or soft brush.
NOTE: It is important to clean the PERMAtech™ filter at the
recommended intervals. Using the ionizer in conjunction with
dirty filters may result in dirty particles exiting the air cleaner and
being attracted to walls, carpets, furniture or other household
objects. These dirty particles may prove very difficult to remove.
Galileo®Wireless Air Quality Center – Multifunctional
providing an indoor air quality display, auto mode, programmable controls, remote operation of air cleaner as well as a
clock and alarm mode.
Air Quality Sensor – Uses an advanced infrared optical
system to constantly detect tiny airborne particles in the air
around the Galileo
®
Wireless Air Quality Center, such as pollen
and dust. It displays the air quality conditions using a series of
LED lights glowing red when high levels of particles are present and green when air quality is improved.
Advanced Communication Technology – Radio frequency
technology sends continuous signals between air cleaner and
Galileo
®
Wireless Air Quality Center.
4
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 7
Page 5
5
Sensor Control Mode – When set to Sensor Control auto
mode, the sensor measures your indoor air quality and adjusts
the fan speed automatically to provide optimum filtration. It also
helps conserve energy by only operating the fan at higher
speeds when needed.
Remote Operation – The function of the Galileo
®
Wireless Air
Quality Center is similar to a remote control. From across the room,
you can operate your air cleaner – you can change speed settings,
turn off appliance or set to sensor control.
Programmable Controls – Gives you the flexibility to program
your air cleaner to turn on and off at your convenience.
Clock/Alarm Mode – Convenient clock and alarm mode
make the Galileo
®
Wireless Air Quality Center multifunctional;
and it replaces tabletop or nightstand clock. Also features a
10 minute snooze alarm.
PRE-OPERATING INSTRUCTIONS
1. Carefully unpack your air cleaner. Select a firm level place
where there are no obstructions to the air inlet or filtered
air outlet. A good location in a room is approximately 1
foot away from the wall, in a central location of your home.
DO NOT POINT AIR OUTLET TOWARDS WALL.
NOTE: IF THE FILTERS ARE ENCLOSED IN PLASTIC
BAGS, PLEASE ENSURE THAT THE BAGS ARE
REMOVED PRIOR TO OPERATION.
2. Carefully remove your Galileo®Wireless Air Quality Center
from the packaging materials. Select a firm level place
on a tabletop or counter where there are no obstructions
to the venting holes.
SYNCHRONIZING INSTRUCTIONS
1. Plug the air cleaner into a 120V AC electrical outlet.
The air cleaner will begin to beep continuously until it is
synchronized with the Galileo
®
Wireless Air Quality Center.
2. Plug the Galileo®Wireless Air Quality Center into a 120V
AC electrical outlet near the air cleaner. It will beep once.
NOTE: The Galileo
®
Wireless Air Quality Center is designed
to operate up to 30 feet from air cleaner.
3. Synchronize the appliances by simply pressing the ON/OFF
button on the Galileo
®
Wireless Air Quality Center. The air
cleaner will beep in rapid succession for a few seconds.
The Galileo
®
Wireless Air Quality Center is now ready to
operate with your air cleaner
PROGRAMMING INSTRUCTIONS
Clock
When the Galileo®Wireless Air Quality Center is plugged into
the electrical outlet, the time will automatically be set at 12:00
AM. After the clock has been set, it will show current time as
Problem
Unit will not
operate
Decreased airflow
Galileo
®
Wireless
Air Quality Center
is not controlling
unit
Air Quality Sensor
lights are always
green
Excessive Noise
Solution
• Check to make sure the unit is
plugged in
• Check to make sure the unit is on by
pressing the power button
• If the Filter Service Indicator is red,
the PERMAtech™ filter should be
cleaned.
• Check the filter to make sure they are
in good condition.
• Check to insure nothing is blocking
air inlet and filtered air outlet.
• Make sure the Galileo
®
Wireless Air
Quality Center is synchronized with
the air cleaner by following synchronization instructions.
• The Air Cleaner and Galileo
®
Wireless
Air Quality Center can be re-synchronized by holding down the ON/OFF
button on both the Air Cleaner and
the Galileo
®
Wireless Air Quality Center
at the same time for 5 seconds until
you hear a rapid beeping sound.
• Chances are there are low levels of
airborne particles around the sensor.
This should not be a concern.
• Remove the plastic bags from the
filters if present.
TROUBLESHOOTING
12
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 9
Page 6
11
10.Replace air inlet grill back onto unit securely.
11.The filter service indicator must be reset once the
PERMAtech™ filters have been cleaned. Reset indicator by
inserting a small object (such as a pin or paper clip) into
the hole below the filter service light.
Filter Life – The filter has been designed to never need replacement however, it does need servicing. We recommend that under
normal conditions of continuous use, the filters should be cleaned
at least every 3 months to help maintain optimal performance.
Should the filter become damaged during cleaning replacements
are available by calling 1-800-253-2764.
Air Cleaner
Model #
BAP2000-U/
BAP2001-U
Filter Quantity
Needed
2
Air Filter
Model #
323-069
Filter
Description
PERMAtech
TM
Filter
L
K
I
J
G
E
A. Inlet Grill
B. Washable Foam Pre-Filter
C. PERMAtechTMFilter
D. Filtered Air Outlet
E. Ionizer Control
F. Ionizer Light
G. Oscillation Button
H. Power Button
I. Speed Control
J. Speed Indicator Light
K. Auto Indicator Light
L. Filter Service Indicator Light
D
A
C
Figure 7
H
F
B
6
long as the appliance is plugged in.
1. To set the clock time, press the “CLOCK” and “SET” buttons
at the same time. The hour numbers will begin to flash.
2. Press “+” or “-” to set desired hour, then press “SET”.
3. When a button has not been pressed for a few seconds
OR when the “SET” button is pressed again, the minute
numbers will begin to flash.
4. Press the “+” and “-” button to adjust the minutes as indicated above in step 2.
5. When a button has not been pressed for a few seconds
OR when the “SET” button is pushed again the clock will
begin operating.
Alarm
The Galileo®Wireless Air Quality Center is equipped with an
alarm clock option.
Setting Alarm
1. To set the alarm, press the “ALARM”
and “SET” buttons at the same time.
The hour numbers will begin to flash
and a small bell will appear in the
bottom right hand corner of the LCD screen.
2. Press “+” or “-” to set desired hour, then press “SET”.
3. When a button has not been pressed for a few seconds
OR when the “SET” button is pressed again, the minute
numbers will begin to flash.
4. Press the “+” and “-” buttons to adjust the minutes as
indicated above in step 2.
5. When a button has not been pressed for a few seconds
OR when the “SET” button is pushed again, the time will
appear on the LCD screen and the alarm is set. A small
bell will now appear in the bottom right hand corner
indicating the alarm is operational.
6. To check the alarm setting, press the “ALARM” button.
The alarm set time will appear. Press the “TIME” button to
return to clock mode.
Turning Alarm OFF
1. When the alarm goes off, a rapid beeping will be heard.
2. To deactivate the alarm press the “ALARM” and “SET”
button at the same time. The bell in the right hand corner
will disappear.
3. The longer the alarm sounds the louder it gets.
4. The alarm has a snooze feature. Press the “ALARM” button
only when the alarm is sounding and the alarm will turn off.
After 10 minutes, the alarm will sound again. The alarm will
continue to go off every 10 minutes until the alarm mode is
deactivated. See step 2 above.
ON TIMER
HI
PM
SENSOR CONTROL
PM
timer
set
clock
alarm
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 11
Page 7
7
PROGRAMMABLE TIMER
The Galileo®Wireless Air Quality Center has a programmable
timer feature. You can program the air cleaner to turn on and
off at your convenience. NOTE: The Galileo
®
Wireless Air
Quality Center must be used to turn the air cleaner on, set the
operating speed and turn air cleaner off in order for the timer
to work (Steps 1-3 below).
1. Using the Galileo
®
Wireless Air Quality Center turn the air
cleaner on by pressing the “ON/OFF” button.
(see Operating Instructions on page 7 for more details)
2. Set the desired operating speed by using the “MODE” button.
3. Then using the Galileo
®
Wireless Air Quality Center turn the
air cleaner off by pressing the “ON/OFF” button.
4. To program the timer press the “TIMER” and “SET” buttons
at the same time
a) Set the “Timer On” time first: To set the time the air
cleaner will come on, press the “TIMER” and “SET”
buttons at the same time. The hour numbers in the
timer section will begin to flash.
b) Press “+” or “-” to set desired hour, then press “SET”.
c) When a button has not been pressed for a few seconds
OR when the “SET” button is pressed again, the minute
numbers will begin to flash.
d) Press the “+” and “-” to adjust the minutes as indicated
above in step 2.
e) When a button has not been pressed for a few seconds
OR when the “SET” button is pushed again, the timer
“ON” will be set and the Timer “OFF” will begin flashing.
f) Set the “Timer Off” time second by following instructions
in step 4a-e.
5. After completing timer set operation, the “TIMER ON” and
programmed time will be displayed.
6. Once the unit has begun operating in timer mode, the
“TIMER OFF” and programmed off-time will appear in the
top display.
7. To turn off the programmable timer, press and hold the
“TIMER” button for 3 seconds.
NOTE: If the air cleaner is turned on before timer mode
begins, the unit will remain on and “TIMER OFF” will appear
on the display. The air cleaner will still turn off as programmed.
GALILEO®WIRELESS AIR QUALITY CENTER
The Galileo®Wireless Air Quality Center serves as a command
center for the air cleaner. It remotely operates the air cleaner by
sending continuous signals from the Galileo
®
Wireless Air Quality
Center to the air cleaner. This one way communication can be
overridden by operating the controls directly on the air cleaner.
When using the Galileo
®
Wireless Air Quality Center, the yellow
LED marked "AUTO" on the air cleaner will illuminate. When
10
water (not dishwasher safe). Dry before replacing in the unit.
3. The front air outlet grill can be cleaned of dust with a small
soft brush or cloth.
WARNING: Do not allow moisture to come in contact with
the main housing of the air cleaner.
PERMATECH™ FILTER CLEANING INSTRUCTIONS
1. Turn off and unplug the unit before cleaning.
2. Filter Service Indicator – Your air purifier has an indicator
light that illuminates when it is time to clean the
PERMAtech™ filters.
3. Every few weeks, check the condition of the filters.
4. Remove the air inlet grill by pulling the air inlet grill towards
you by grasping the finger tabs on both sides.
5. Remove and examine the foam pre-filter. If it has collected a
noticeable amount of dust or lint, remove it from the inlet of the
grill and wash it in warm soapy water. Rinse and drip dry the
pre-filter thoroughly before replacing it into the inlet of the grill.
6. With the rear grill removed, check the condition of your
PERMAtech™ filters. If the filters are dirty, remove them by
gripping on both sides and pulling forward.
7. To clean the PERMAtech™ filter use a crevice tool or brush
attachment with your vacuum cleaner. Run the attachment
along the inlet and outlet side of the filter trying to clean
between the pleated filter layers. (Figure 4).
DO NOT USE WATER OR ANY OTHER HOUSEHOLD
CLEANERS OR DETERGENTS TO CLEAN THE
PERMAtech™
FILTER.
NOTE: Vacuuming will restore
performance of the PERMAtech™
filter however, the filter may appear
stained. This is normal and does
not affect performance in any way.
8. This model utilizes a hang tab and
filter clips to insure that the filter is
properly in place. Before replacing
the PERMAtech™ filter make sure
that the hang tab is securely in place.
The clip can only be attached to the
tabs on the filter one way. The filter
clip should easily slide onto the filter
hang tab with only a small amount of
pressure. DO NOT use force while
attaching the clip to the filter. (Figure 5).
9. Align the clip on the top of the
PERMAtech™ filter with the rails on
the inside of the purifier unit. Gently
slide the filter onto the rail (Figure 6).
NOTE: The side with the soft gas
ket should face inward.
Figure 4
Figure 5
Figure 6
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 13
Page 8
9
or low levels of airborne particles to red which shows poor
air quality conditions or high levels of airborne particulate.
•The air quality sensor operates continuously when the
Galileo
®
Wireless Air Quality Center is plugged into a 120V
AC outlet, even when the air cleaner is turned off.
SENSOR CONTROL MODE
When the Galileo®Wireless Air Quality Center is in the “Sensor
Control” mode, it will automatically adjust the fan setting to the
optimum speed based on the air quality conditions and particle
levels in the air. As the particle concentration in the air rises, so
does the speed. In sensor control mode, the unit will always run
at a minimum of SLEEP speed even if the particle levels are low
to maintain ideal conditions.
1. To turn the air cleaner onto “Sensor Control” mode, you
must use the Galileo
®
Wireless Air Quality Center.
2. Turn the air cleaner on using the Operating Instructions.
Select the desired operating speed by scrolling through
the settings using the “MODE” button. You can select from
“HIGH” , “MEDIUM”, “LOW”, “SLEEP” or “Sensor Control.”
3. Once in “Sensor Control” mode, the air cleaner speed will
fluctuate depending on airborne particulate concentration.
NOTE: The Sensor Control mode cannot be controlled from
the air cleaner control panel. It can only be controlled using
the Galileo
®
Wireless Air Quality Center.
AIR QUALITY SENSOR CLEANING INSTRUCTIONS
It is recommended that you clean the air quality sensor monthly
to maintain accurate monitoring or particulate levels.
1. Turn off and unplug unit before cleaning.
2. The air quality sensor is located on the
back side of the Galileo
®
Wireless Air
Quality Center.
3. Open the sensor door (see Figure 3)
4. Use a dry cotton swab to gently clean
the sensor lens. Do not use any water
or cleaning agents.
5. Securely close the sensor door. If it is not
closed, the sensor may not operate properly.
OSCILLATION
The air cleaner is equipped with oscillation. To start and stop
oscillation of the air cleaner, push the button identified as
Oscillation ( ) on the air cleaner control panel.
CLEANING/MAINTENANCE INSTRUCTIONS
Turn off and unplug the unit before cleaning.
1. The outside of the air cleaner can be cleaned with a soft,
damp cloth.
2. The rear air inlet grill can be removed and washed in warm soapy
Figure 3
operating controls directly on the air cleaner, the yellow LED light
will turn off. To resume primary control from the Galileo
®
Wireless
Air Quality Center, press the “ON/OFF” or “MODE” button. The
yellow LED light on the air cleaner will again illuminate.
OPERATING INSTRUCTIONS
1. The air cleaner can be operated from either the control
panel directly on the air cleaner or the Galileo
®
Wireless Air
Quality Center.
2. To turn the air cleaner on, press the “ON/OFF” button on the
Galileo
®
Wireless Air Quality Center OR press the power button
( ) on the air cleaner.
3. Select the desired operating speed. You can select from HIGH
( ), MEDIUM ( ), LOW ( ) or SLEEP ( ) by pressing
the “MODE” button on either the air cleaner control panel or
the Galileo
®
Wireless Air Quality Center.
4. The light on the control panel will illuminate letting you know
the power is on and at what speed the air cleaner is operating.
5. To release negative ions into the filtered air, press the
ionizer button ( ) to ON and the light will illuminate.
6. For optimum air filtration, it is recommended to operate
the air cleaner continuously. Its rugged motor has been
designed to provide many years of continuous use.
For continuous use, it is recommended to operate the air
cleaner on the LOW or MEDIUM setting. For quieter operation
or use in a bedroom, select the LOW or ultra-low SLEEP
setting. When high levels of air pollution are present, select
the HIGH setting to quickly circulate and filter the room air.
NIGHTLIGHT
Your Galileo®Wireless Air Quality Center has a built in nightlight
which automatically turns on as your room gets dark. To turn off
this nightlight, press the “+” and “-” buttons at the same time.
To turn this function back on simply press both buttons again.
Note: When any button is pressed the backlight will come on
for a few seconds.Once no buttons are pressed again for 5
seconds, the light will go off.
AIR QUALITY SENSOR
Your Bionaire®Air Cleaner comes with an Air Quality Sensor
which uses an advanced infrared optical system to constantly
detect tiny particles in the air around the Galileo
®
Wireless Air
Quality Center such as pollen and dust. It also displays the air
quality even when the air cleaner is turned off, using a series of
colored lights. Radio frequency technology sends continuous
signals between the air cleaner and the Galileo
®
Wireless Air
Quality Center sensor and adjusts air cleaner to improve air
quality wherever it is placed.
• The air quality sensor uses a series of lights to indicate air
quality conditions and particle levels. The lights range in
color from green, which indicates good air quality conditions
8
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 15
Loading...