Page 1
BiPAC 7700N R2
Wireless-N
ADSL2+ Firewall Router
Quick Start Guide
Page 2
Page 3
Billion BiPAC 7700N R2 Wireless-N ADSL2+ Firewall Router
-1-
PPaacckkaaggee CCoonntteennttss
BiPAC 7700N R2 Wireless-N ADSL2+ Firewall Router
CD containing the on-line manual and Setup Wizard Utility
RJ-11 ADSL/ telephone cable
Ethernet (RJ-45) cable
Two 2dBi detachable antennas
Power adapter
Quick Start Guide
Splitter/ Micro-filter (Optional)
Attention
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.
Do not use the
router
in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this
product
and all
accessories
outdoors.
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Page 4
Quick Start Guide
-2-
HHaarrddwwaarree OOvveerrvviieeww
The Front LEDs
The bottom Casing
When the system is
ready, it will be lit
green. Lit red when the
device fails to boot.
Lit green when success
fully
connected to an Ethernet
device. Blinking when data is
being transmitted / received.
Lit green when the
device is successfully
connected to an ADSL
DSLAM. (“line sync”)
Lit green when a
wireless connection
is established. Unlit
when wireless is
disabled.
Lit red when WAN port fails to
get IP address. Lit green when
WAN port gets IP address
successfully. Unlit when the
device is in bridge mode or
WAN connection is absent.
Press for more than 5
seconds to restore the
device to its factory
default mode.
Flash green when
WPS configuration
is in progress.
Page 5
Billion BiPAC 7700N R2 Wireless-N ADSL2+ Firewall Router
-3-
The Rear Ports
Note: For WPS configuration, please refer to the WPS section of User Manual.
HHaarrddwwaarree CCoonnnneeccttiioonn
Connect it with the
supplied power
adapter.
Connect the supplied
RJ-11 cable to this port
when connecting to the
ADSL/telephone network.
Connect your computer to
a LAN port, using the
included Ethernet cable
(with RJ-45 cable).
Power
ON/OFF
switch
Push WPS button
to trigger Wi-Fi
Protected Setup
function.
*1
Press to enable wireless
when wireless is disabled
and the WLAN LED lit.
Press to disable wireless
when wireless is on and
the WLAN LED will be OFF.
Page 6
Quick Start Guide
-4-
HHaarrddwwaarree IInnssttaallllaattiioonn
1. Power Connection
Plug the supplied power adapter in
to the wall jack and the other side to the router.
Please note that the plug type may differ according to country.
2. Ethernet Connection
Connect the supplied RJ-45 Ethernet cable to one of the Fast Ethernet (LAN)
ports, and the other side to the PC’s Ethernet interface.
3. ADSL Connection
Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other
side to the phone jack on the wall.
Page 7
Billion BiPAC 7700N R2 Wireless-N ADSL2+ Firewall Router
-5-
4. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct
high-frequency signals to the ADSL modem & low frequency signals to the
telephone or other analogue device to prevent inter-modulation distortion & get
good speed/stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an
internal micro-filter can be employed at each analog device.
SSeettuupp UUttiilliittyy
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to
setting up the basic network configuration.
CCoonnnneeccttiinngg ttoo tthhee RRoouutteerr
1. Open the web browser and type http://192.168.1.254
in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
Page 8
Quick Start Guide
-6-
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
TTrroouubblleesshhoooottiinngg
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of ADSL line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
PPrroodduucctt SSuuppppoorrtt aanndd CCoonnttaacctt IInnffoorrmmaattiioonn
Most problems can be solved by referring to the Troubleshooting section in the user manual. If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
CCoonnttaacctt BBiilllliioonn
Billion Australia - http://au.billion.com
Basic Support Hotline - (02) 8999 0728 (Basic Support)
Helpdesk – http://au.billion.com/helpdesk/ (Lodge a support ticket)
Billion Support Forums –
http://au.billion.com/forums (Get help & suggestions from
Billion & other users)
Download site -
http://au.billion.com/product/fd.php (Download latest firmware, drivers &
User Guides)
BiPAC 7700N
R2:
V1.0
0AU
Loading...