Page 1
BiPAC 5400N R2
Wireless-N ADSL2+
Firewall Router
Quick Start Guide
Page 2
Billion BiPAC 5400N R2 Wireless-N ADSL2+ Firewall Router
1
Package Contents
BiPAC 5400N R2 Wireless-N ADSL2+ Firewall Router
CD containing the on-line manual
RJ-11 ADSL/ telephone cable
Ethernet (CAT-5 LAN) cable
Power adapter
Quick Start Guide
Splitter/ Micro-filter (Optional)
Attention
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS
CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL
THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU
NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION,
PLEASE REFER TO THE USER MANUAL ON THE CD-ROM.
Do not use the
router
in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this
product
and all
accessories
outdoors.
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Page 3
Quick Start Guide
2
Hardware Overview
The Front LEDs
The Rear Ports
*
Note:
1. For WPS configuration, please refer to the WPS section of user manual.
2. USB feature is not supported by 5400N R2, please don’t try to connect to this port in case of
any damage.
Connect the
supplied power
adapter to this jack.
Connect the supplied
RJ-11 cable to this port
when connecting to the
ADSL/ telephone network.
Push WPS but
ton to
trigger Wi-Fi Protected
Setup function.
*1
Lit
green when
power is on.
Lit
green
when connected
to an Ethernet device.
Lit green when the wireless
connection is established.
Flashes when the device is
sending/ receiving data.
L
it green when
WAN port gets IP
address successfully. Unlit when
the device is in bridge mode or
WAN conne
ction is absent.
Lit
green
when successfully
connected to an ADSL DSLAM
(“line sync”); flash green when
the device is establishing the
active DSL link.
Connect your computer to a
LAN port with the included
Ethernet cable
.
Flash green when
WPS configuration is
in progress.
Connect
with
wireless
antenna
Press
1~2 seco
nds
to switch on/ off
wireless.
Power ON/
OFF
switch.
For the USB
connection*
2
Page 4
Billion BiPAC 5400N R2 Wireless-N ADSL2+ Firewall Router
3
Hardware Connection
Press it to reset the
device to restore or
factory default
settings.
Page 5
Quick Start Guide
4
Hardware Installation
1. Power Connection
Plug the supplied power adapter to the wall jack and the other side to the router. Please
note that the plug type may differ according to country.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other
side to the PC’s Ethernet interface.
3. ADSL Connection
Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other side to
the phone jack on the wall.
Page 6
Billion BiPAC 5400N R2 Wireless-N ADSL2+ Firewall Router
5
4. Splitter/ Micro-filter Connection
Splitter / Micro-filter are important for ADSL installation. High-frequency signals are
directed to the ADSL modem, and low-frequency signals are directed to the telephone
or other analog voice-channel device to prevent inter-modulation distortion and also to
get good speed and stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a splitter
can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
Setup Utility
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard and it will guide you
to setting up the basic network configuration.
Page 7
Quick Start Guide
6
Connecting to the Router
1. Open the web browser and type http://192.168.1.254
in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may
have a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the
subnet mask are consistent between the router and the workstations.
3. Frequent loss of ADSL linesync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them
and the wall socket (unless you are using a Central Splitter or Central Filter installed by a
qualified and licensed electrician), and ensure that all line filters are correctly installed and
the right way around. Missing line filters or line filters installed the wrong way around can
cause problems with your ADSL connection, including causing frequent disconnections. If
you have a back-to-base alarm system you should contact your security provider for a
technician to make any necessary changes.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual.
If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
http://www.billion.com
BiPAC 5400N R2: V1.00EN
Loading...