Page 1
User guide
Billi Alpine Sparkling
Page 2
User guide
Billi Alpine Sparkling.
Contents
Warnings & Important information ........2
General Maintenance.....................3
Features and Modes......................3
Filtration Information.....................3
Changing the filter .......................4
Replacement.......................5-6
CO
2
Service Support .........................7
Warnings & Important information
– For continued safety of this appliance it
must be installed, operated and maintained
in accordance with the manufacturer's
instructions.
– Your appliance should be installed by
a suitably qualified tradesperson.
– For correct operation of this appliance
it is essential to observe the instructions
as outlined in this booklet.
– Do not use this appliance with water that
is microbiologically unsafe or with water
of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may
be used on disinfected water that may
contain filterable cysts.
– Filter replacement must be performed
at intervals of not more than 12 months.
– Use this appliance only as directed
in these instructions and only for its
designed purpose.
– This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
– Children should be supervised to ensure
that they do not play with the appliance.
– If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid creation of a hazard.
– New hose sets supplied with the appliance
are to be used. Old hose sets should not be
re-used.
2
Page 3
User guide
Billi Alpine Sparkling.
General Maintenance
Your Billi Alpine has been designed to require
minimal maintenance other than replacement
of filter cartridges. During each filter change,
check all water connection fittings for signs
of leakage. Check all tubing for any signs of
damage. Check the cupboard area around
the base of unit for any signs of moisture.
Cleaning the dispenser
Your Alpine Dispenser is fabricated from robust
metal with a tough protect chrome plating.
Care of dispenser is as with any chrome plated
tapware. Avoid using abrasive cleaners. Wipe
clean using a damp cloth.
Use of a non-solvent, non-smearing cleaner
such as Windex is recommended. Do not
pour water over dispenser.
Cupboard ventilation requirements
Your Alpine Sparkling underbench module
requires cupboard ventilation, refer to install
guide for details. Care should be taken when
using the cupboard space, to avoid stretching
or damaging plastic pipe work. Check fittings
and tubing at each filter change for signs of
damage or leakage. Always ensure access
to power switch and water supply tap is not
restricted.
Features and Modes
Slimline Dispenser
To dispense filtered water, the dispenser
tap lever will need to be rotated. The lever
will automatically return to the o position.
The spout can be swivelled to suit your
installation.
Billi Filter Cartridges
The Billi Alpine uses environmentally friendly,
element-type cartridges. The two-stage system
includes a Sediment Removal pre-filter and
Chemical Removal post-filter.
There are 2 types of filter cartridge sets oered.
994001 This is the standard filter cartridge
set used in the Alpine system.
This combination is designed
to remove or reduce sediment, taste
and odour, chlorine, chemicals and
pesticides. This combination is rated
to remove particles greater than 10
microns in size and is best suited to
normal quality town water supplies.
994002
Use only genuine Billi Filter Cartridges as
designed for this system.
If the system has not been used for a period
of 3 days or more, lift the dispenser lever and
flush the system for at least 1 minute.
This combination incorporates a
high quality, sub-micron, carbon
block filter and is NSF certified
for the safe removal of potentially
healththreatening Giardia and
Cryptosporidium cysts. As well
as removing or reducing the
contaminants as listed for the
990402 cartridge etc., the chemical
cartridge is certified to remove or
reduce heavy metals such as lead; an
unseen potential health hazard.
Adjustable chilled water temperature
The chilled water deilvery temperature
can be adjusted to suit your preference.
The blue control knob, located on the front
of the Chiller Module, can be adjusted if a cooler
or warmer temperature is required.
3
Page 4
User guide
Billi Alpine Sparkling.
Filter Cartridges Service Interval
Periodic replacement of your Billi Alpine
filter cartridge is necessary to maintain the
sparkling freshness of your drinking water.
Your Billi Representative will advise you of
an appropriate service interval. As a guide,
the filters should be serviced twice yearly.
In areas where water supply has a high level of
sediment, more frequent replacement of filter
cartridges may be necessary. This will become
evident when a significant drop in delivery flow
rate occurs.
Filter Cartridge Replacement
When you receive your replacement cartridges,
follow the procedure as
outlined below:
1. Turn o blue tap under bench.
2. Operate dispenser lever to release pressure.
3. Hold filter and swing towards you slowly.
The top of the filter is in a hinged cradle
assembly. It should stop after approximately
30 degrees of travel.
4. The filter can now be released from the
holding cradle by pulling down on the filter.
5. Take care not to spill water in the base of the
tray. If so wipe gently with absorbent paper.
6. Install new filter into the same location
by pushing all the way up into the cradle.
7. Push filter back into the unit until it locks
into place.
8. Turn on blue tap under bench and check
for water leaks.
9. Operate dispenser lever and run water for 3
minutes to flush and condition the new filter.
4
Page 5
User guide
Billi Alpine Sparkling.
Removing the CO2 cylinder
1. Isolate the water supply and turn o
the power.
– This will prevent the internal pump
from pressurizing the system.
2. Turn o the CO
black knob anti-clockwise.
3. Drain any remaining pressure by activating
the sparkling water option on the dispenser
installed.
Ensure the pressure gauge shows near to
zero pressure – if the pressure is less than
one bar, and the dial is fully anti-clockwise,
then the cylinder can be removed with only
a small amount of CO
4. Hold the regulator and rotate the Cylinder
clockwise to remove.
– If the bottle is not empty, CO
while you are turning the bottle. The bottle
will self-seal prior to the thread being free
from the regulator.
– Avoid breathing air containing CO
contact with the cold escaping gas as
per the Safety Data Sheet.
regulator by turning the
2
escaping
2
may escape
2
or
2
5
Page 6
User guide
Billi Alpine Sparkling.
Installing the CO2 cylinder
1. Ensure all connections between the
regulator and unit are secure.
Position the regulator on top of the CO
cylinder.
2. Tighten the bottle by rotating anti-clockwise.
– CO
will escape while you are turning the
2
bottle. Continue to turn the bottle to form
a seal with the regulator.
3. Open the pressure regulator by turning the
black knob clockwise.
– Set the initial pressure to around 3 Bar.
– Turn on the unit power and water supply.
– Wait for the unit to come back to
temperature.
4. Check bottle and connections for leaks using
soapy water to test for bubbles.
NOTE: the ¼" tube and pushfit fittings may
settle when the pressure is turned on.
5. Increase the pressure to set your level of
carbonation.
Initial set point may vary once the unit is
running, you may need to reset the pressure
once the system has stabilised.
WARNING: do not set the pressure above 5 bar.
2
6
Page 7
User guide
Billi Alpine Sparkling.
Thank you for choosing to install a
Billi Alpine Sparkling Drinking Water
Appliance. Your Alpine Sparkling is
manufactured to exacting standards
using high quality materials and with
proper maintenance and care, should
function for many years.
For information on our filtration
and service contract please contact
Billi Head Oce on 1800 812 321
or email us at service@billi.com.au.
For technical support please call
1800 812 321 and speak to one of
Billi’s experienced technician’s.
To book a service call out request
a filter change or please contact
the Billi Service Centre on
1800 812 321 or book online
at www.billi.com.au
Filter cartridges are also
available for purchase online
at www.billi.com.au
7
Page 8
Billi Australia Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone +61 3 9469 0400
Facsimile +61 3 9469 0499
www.billi.com.au
Designed and manufactured in Australia.
As Billi Australia Pty Ltd has a policy of
continual improvement, all details are
subject to change without notice. All
goods are sold subject to our published
terms and conditions. Billi is a
registered trademark. 0618
Loading...