
Owner’s Manual
for Assembly, Operating & Maintenance of
Model M-35B Charcoal Rotisserie
www.bigjohngrills.com
YOU MUST READ THIS OWNER’S MANUAL BEFORE
OPERATING YOUR CHARCOAL ROTISSERIE.
WARNING: Do not ignite this grill without reading the
LIGHTING INSTRUCTIONS first.
WARNING: DO NOT store or use
gasoline or other flammable liquids/
vapors in this grill or in the vicinity of this
grill.
THIS CHARCOAL GRILL IS DESIGNED FOR OUTDOOR USE ONLY.
526 EAST ROLLING RIDGE DRIVE, BELLEFONTE, PA 16823
P: 814-359-2755 F: 814-359-2621 info@bigjohngrills.com
1

TABLE OF CONTENTS
1. GENERAL INFORMATION Page 3
2. ASSEMBLY INSTRUCTIONS Page 4
3. SET-UP INSTRUCTIONS Page 5
4. OPERATING INSTRUCTIONS Page 6
5. CLEANING & CARE INSTRUCTIONS Page 7
6. PARTS LIST Page 8
7. ACCESSORY LIST Page 9
8. WARRANTY Page 10
9. WARNINGS Page 11
2

GENERAL INFORMATION
Thank you for purchasing a The Original Big John “Low Boy” Charcoal Rotisserie! We take pride in producing and selling equipment made right here in America and are pleased that you recognized the quality and durability of our products. Your new Big John Charcoal Grill is a commercial grade, outdoor
piece of cooking equipment. With this rotisserie, you will be able to roast a variety of foods quickly and
easily. This unit is portable meaning you can take it and use it anywhere. Big John charcoal rotisseries
are used at offsite catering events & festivals, restaurants, hotels & resorts, rental stores, golf courses,
personal homes and many more.
Big John products are designed for OUTDOOR USE ONLY! Only operate this equipment in a well-
ventilated area. Do not use in garage, building, or other enclosed area. Operation of this equipment
indoors or in a poorly ventilated area may cause an explosion, fire, personal injury, or death.
Do not retrofit any equipment or accessories to the unit that is not part of the original equipment
provided by Big John Grills & Rotisseries. Replacement parts must be obtained from the manufacturer. Any attempt to change or modify this unit could result in an explosion, fire, personal injury to
yourself or someone else, or death.
Do not touch or allow any contact with the sides, back, or top of firebox or stainless steel compo-
nents after lighting - the unit is EXTREMELY HOT! Allow the unit to cool completely before touching
any surface.
DO NOT operate rotisserie within 12” of a combustible or non-combustible surface. Provide ade-
quate clearance and ventilation at all times
DO NOT perform any maintenance or cleaning until unit is completely cooled down.
DO NOT burn logs or sticks of wood in this rotisserie. Wood burns hotter than charcoal and will
cause damage to the firebox with long term use.
DO NOT pour water over hot coals as it may cause the metal to warp and void the warranty.
Wood Pellets can be used to add the smoke flavor to food by throwing a handful in on top of the
charcoal
3

ASSEMBLY INSTRUCTIONS
This unit ships 90% assembled and we make sure the instructions for the rest are easy to follow and
perform. Please follow the instructions below to ensure your rotisserie is properly assembled for safe
operation and remember this is a commercial piece of equipment and therefore the materials used to
build it are of the best quality. Because of this, the weight is considerable and will require 2 people to un
-package, assemble, and set-up the unit.
1. Unbox rotisserie and remove all packaging materials, tape, and plastic coverings.
2. Turn unit upside down so leg sockets are on top.
3. Screw legs firmly into the sockets on the bottom of the firebox.
4. IF YOU PURCHASED WHEEL LOCKS
a. You will need a 9/16” Wrench & a 1/2” Wrench to complete the installation
b. Disassemble current casters by taking off nut and pulling old bolt out (discard old bolt)
c. Put new caster brake on yoke by inserting the tab on the brake into the slot on the side
fork of the yoke while lining up the slotted hole with the bolt hole on yoke. The shoe of
the brake will be on the inside of the yoke near the top.
d. Put wheel between forks of yoke and insert the new, longer bolt from the kit with the
taps facing outward away from the wheel with the “ON/OFF” symbols facing upward.
e. Attached the nylon lock nut to the bolt and tighten. Do not over tighten or wheel will not
spin.
f. Screw wheel into leg.
5. Flip unit upright and secure wheels so they will not move.
6. Rotate the motor end mount and point protector end mount 180° degrees so they are facing out
7. Adjust both end mouths to the lowest height setting and secure with stainless steel pins.
4