The Desono MASK2 2.5" surface mount loudspeaker
delivers crystal clear sound for all your public address and
background music needs. Available in black or white, its
2.5” paper cone woofer provides high SPL and extremely
low distortion, ensuring unprecedented clarity over the
entire frequency spectrum.
Brackets supplied with the MASK2 loudspeakers allow
them to be mounted under various angles, in corners, or
on solid surfaces such as walls or ceilings.
In combination with the compact dual coil SUBLIME
subwoofer, the Desono MASK2 loudspeakers are the
perfect solution for small and medium-sized rooms that
demand superior speech intelligibility and full range music
reproduction.
A:9300 S.W. Gemini Drive Beaverton, OR 97008 USA W:www.biamp.com
FEATURES
• One of the smallest loudspeakers on the market
• IP60 rated
• 2.5” paper cone woofer
• Innovative turn/tilt bracket
• Pairs well with Desono SUBLIME subwoofer
CAUTION: Do not attempt to use MASK2
units as full range loudspeakers. They are not
designed to reproduce bass frequencies and do not
have overload protections. Biamp recommends using
matching subwoofers (SUBLIME) and/or high-pass
filter systems. Contact Support for the recommended
components to use with MASK2 loudspeakers.
MOUNTING THE SPEAKER
1. Point the center of the speaker at
the center of the listening area.
2. Test t the speaker on the
bracket to ensure the desired
angle (see Step 7) before
mounting the bracket on the
wall.
3. Using the bracket as a
template, drill the mounting
holes as shown in Figure 1.
Note: The base plate may be rotated by 45 or 90
degrees to get the maximum tilt angle in the desired
direction when installing in a corner.
4. If the speaker location is pre-wired, thread the wiring
through one of the four pre-cut cable entries on the
bracket base prior to mounting the bracket (Figure 2).
Mounting Holes
Figure 1.
Drill mounting holes
Figure 2.
Guide speaker
wiring through
bracket base
7. Determine the angle of the speaker by adjusting
the bracket base and the H-hook on the half-sphere
ball. The H-hook can be adjusted with or without the
speaker attached to the hook. Adjust the turning force
of the H-hook by tightening or loosening the central
screw (Figure 5).
Figure 5.
Adjust speaker
and bracket
8. Slide the rubber security piece (a) out from the back
of the speaker and slide the speaker on to the H-hook
(b) on the mounting bracket. Slide the rubber piece
back in place to lock and secure the cabinet
(Figure 6).
b
5. Mount the bracket to the surface (Figure 3). The
mounting materials for solid brick walls are included.
Figure 3.
Mount the
bracket
6. Tighten all the screws and cover with the screw
covers (Figure 4).
Screw Cover
Figure 4.
Tighten the
screws and
insert covers
Figure 6.
a
Attach speaker to
bracket
9. Remove the euroblock connector (a) from the
speaker and connect the speaker wires (b)
maintaining the polarity marked on the back of the
speaker: + is positive, - is negative (Figure 7).
Fully insert the bare portion of each wire into the
connector. Maintain the same color code for all of the
sound system wiring from amplier to loudspeakers.
Note: For distances up to 20 meters, 0.75 mm²
(18AWG) speaker wire can be used without loss of
performance. For longer distances use thicker wire.
a
Connect speaker
b
Figure 7.
wires
page 2 Installation and Operation Guide MASK2
CEILING MOUNTING
The MASK2CMT bracket enables installing the MASK2
loudspeaker on the ceiling.
This small metal extension piece can be installed on the
existing MASK2 wall mount.
The bracket extension enables more inclination of the
MASK2 speaker mounted on the ceiling.
8Ω TECHNOLOGY
Features:
• dynamic high power
• stereo Hi-Fi quality
• same volume in all zones
• max four cabinets on a stereo Hi-Fi amplifier
Bracket
Extension
8Ω8Ω8Ω8Ω
4Ω4Ω
CAUTION: Do not attempt to use MASK2 units as
full-range loudspeakers. They are not designed to
reproduce bass frequencies and do not have overload
protections. Biamp recommends using the SUBLIME
subwoofers (or similar) and/or high-pass filter systems.
Contact Support for the recommended components to
use with MASK2 loudspeakers.
CAUTION: The overload protection system is
incorporated in subwoofers and amplifiers, NOT in
the MASK2 speaker.
CONCEPT1
MASK2 Installation and Operation Guide page 3
CONNECTING TO A SUBLIME SUBWOOFER
Connect the left output from the
power amplifier to the left input of
the SUBLIME subwoofer.
Connect the right output from the
power amplifier to the right input of the
SUBLIME subwoofer.
Connect the left satellite speaker
(MASK2) to the left output of the
SUBLIME subwoofer.
PAINTING THE LOUDSPEAKER
CAUTION: Although the loudspeaker is paintable,
the MASK2 grille is not removable and should not be
painted.
1. Fully mask the grille and loudspeaker face so that
all internal components will not receive any paint.
Also mask o any input, mounting connections, and
safety labels. Don't use conventional masking tape
and NEVER use duct tape. These kinds of tape leave
adhesive residue that is dicult to remove and may
cause damage. Painter's or other low-adhesive tape
is best.
2. Spray paint with two light coats. Let all components
dry completely before reassembly.
3. Remove all of the masking materials.
Connect the right satellite speaker
(MASK2) to the right output of the
SUBLIME subwoofer.
CAUTION: NEVER use abrasives, gasoline,
kerosene, acetone, methyl ethyl ketone (MEK),
paint thinner, harsh detergents or other chemicals on
the loudspeaker. These chemicals and agents may
permanently damage the nish. Some are also toxic
and highly ammable.
CAUTION: Blocking the grille holes with paint
or getting any paint on the drivers or internal
parts will aect loudspeaker performance and void the
warranty.
page 4 Installation and Operation Guide MASK2
CONTACT US
Email: support@biamp.com
Web: support.biamp.com
Warranty: biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
A:9300 S.W. Gemini Drive Beaverton, OR 97008 USA W:www.biamp.com
JUL 2021
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.