Bh fitness R8 User Manual
BH FITNESS R8 RECUMBENT CYCLE
OWNER’S MANUAL
BH FITNESS
20155 Ellipse
Foothill Ranch, CA 92610
Phone: 949-206-8152
Fax: 949-206-0013
Email:
fitness@bhnorthamerica.com
Web: www.bhnorthamerica.com
Revised: 9/19/07
R8 RECUMBENT CYCLE
INTRODUCTION
Congratulations for selecting the R8 Recumbent Cycle as your primary source of fitness.
The BH Fitness R8 offers many exercise programs that benefit users of all levels and ages.
The R8 is designed to make your workouts more effective and enjoyable.
Please read this manual carefully before using the R8. This will allow you to get a full
understanding of all the features the BH Fitness Recumbent Cycle provides. If you have
questions or concerns, please contact BH FITNESS or any authorized BH FITNESS
distributors in your area.
BH FITNESS
20155 Ellipse
Foothill Ranch, CA 92610
Phone: 949-206-8152
Fax: 949-206-0013
Email: fitness@bhnorthamerica.com
Web: www.bhnorthamerica.com
BEFORE YOU BEGIN
It is very important to become familiar with the frequently used components of your R8.
1
R8 RECUMBENT CYCLE
TABLE OF CONTENTS
SECTION PAGE
1. IMPORTANT SAFETY INSTRUCTIONS ...................................................... 3
2. ASSEMBLY INSTRUCTIONS ...................................................................... 4
3. COMPUTER CONSOLE .............................................................................. 17
4. CONSOLE OPERATION .............................................................................. 18
5. WARRANTY ................................................................................................. 25
2
R8 RECUMBENT CYCLE
SECTION 1
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using the Recumbent Cycle.
Notice: Before using this or any other exercise equipment consult your family physician
or health care professional to develop a well planned exercise program to fit your health
needs. If you encounter any pain or breathing discomfort while working out, STOP!, and
consult a physician before continuing.
WARNING!
1. Keep children away from machine while in use.
2. Do not wear loose or dangling clothing while using the cycle.
3. Maximum user weight of this cycle is 300 lbs.
4. Keep a minimum clearance of 18” on each side and 24” at the rear of the cycle for
safety.
5. The cycle should never be left unattended when in operation.
6. Close supervision is necessary when this appliance is used by or near children, invalids,
or disabled persons.
7. Use this appliance only for its intended use as described in this manual.
8. Do not use any attachment not recommended by the manufacturer.
9. Never operate this appliance if it is not working properly. Call your service center for any
service concerns before taking your cycle in for repair.
10. Never drop or insert any object into any opening.
11. Do not use outdoors.
12. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
13. This appliance is intended for household use only.
14. Clean with soap and slightly damp cloth only; never use solvents.
SAVE THESE INSTRUCTIONS
3
–
(
)
(91)
Allen Bolt M6
35
–
2
PCS
Screws Bag
(116) 4mm Allen
Wrench – I PCS
R8 RECUMBENT CYCLE
SECTION 2 - ASSEMBLY INSTRUCTIONS
(118) 6mm Allen
Wrench – I PCS
(108) Allen Bolt M8×15 - 16PCS (5) Waaher 18×9×2.0t – 16 PCS
(41) Self Tapping Screw ST4x25 – 4 PCS
(117) Wrench - I PCS
2 PCS (142) Spring Washer M8
(5)Washer 18
×
9
×
20.t – 2 PCS
×
2.0t – 2 PCS
(114) Allen Bolt M8
×
45 - 2 PCS (143 M8 Nut-
(109) Screw M8×56 – 4 PCS (110) M8 Nut – 4 PCS (112) Spring
Washer M8×2.0t
×
4PCS
113
Washer 20×9×2.0t - 4 PCS
4
Assembly Parts
Chest Strap (126)
R8 RECUMBENT CYCLE
ASSEMBLY INSTRUCTIONS CONTINUED
Seat (102)
Handrail (59)
Frame (1)
Backrest (103)
Rear Stabilizer (74)
Foot Pedal (L) (119)
Left Rear Cover (48)
Bottle Holder (107)
Right Rear Cover (49)
Front Stabilizer (66)
Foot Pedal (R) (120)
Plastic Pad (90)
Computer (97)
Bottle (106)
Upright (80)
Seat Sliding
Base (51)
Handrail (96)
Iron Bar (104)
5
(
p
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 1. Assembling the Front Stabilizer
R8 RECUMBENT CYCLE
S
ring Washer M8×2.0t - 2PCS (112)
Washer 20×9×2.0 - 2PCS (113)
M8 Nut - 2PCS
Screw M8×56 - 2PCS (109)
110)
Refer to the drawing to the right.
Attach the Front Stabilizer (66) to
the Front Frame (1) with Bolts
(109), Washers (113), (112) and
Acorn Nuts (110). Tighten the nuts
with the Open Spanner (117).
6
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 2. Assembling the Rear Stabilizer
R8 RECUMBENT CYCLE
Spring Washer M8×2.0t - 2PCS (112)
Washer 20×9×2.0t - 2PCS(113)
M8 Nut - 2PCS (110)
Screw M8×56 - 2PCS (109)
Refer to the drawing to the right.
Attach the Rear Stabilizer (74) to
the Frame (1) with Bolts (109),
Washers (113), (112) and Acorn
Nuts (110), Tighten the nuts with
the Open Spanner (117).
7
Loading...