Esta bicicleta ha sido diseñada y
construida de modo que proporcione
la máxima seguridad. Sin embargo,
deben aplicarse ciertas precauciones
al utilizar aparatos de ejercicio.
Lea el manual en su totalidad antes de
montar y utilizar la bicicleta. Este le da
indicaciones importantes sobre el
montaje, seguridad y uso de la
máquina.
Asimismo, cumpla con las siguientes
precauciones de seguridad:
1 Mantenga a los niños y animales
domésticos, alejados de este aparato
en todo momento. NO los deje
desatendidos en la habitación en la
que guarda la bicicleta.
2 Sólo puede utilizar el aparato una
persona cada vez.
3 Si sufre mareos, nauseas, dolor en
el pecho o cualquier otro síntoma
durante la utilización de este aparato,
PARE el ejercicio. ACUDA A UN
MÉDICO INMEDIATAMENTE.
4 Utilice el aparato sobre una superficie
sólida y a nivel. NO utilice la bicicleta
cerca del agua o al aire libre.
5 Mantenga las manos alejadas de las
partes en movimiento.
6 Utilice una indumentaria adecuada
para la realización de ejercicio. No use
prendas holgadas que podrían
engancharse en la bicicleta. Utilice
siempre calzado para correr o para
aerobic cuando utilice la máquina.
Átese los cordones correctamente.
7 Utilice este aparato sólo para los
fines descritos en este manual. NO
5
utilice accesorios no recomendados
por el fabricante.
8 No coloque objetos cortantes
alrededor de la máquina.
9 Las personas discapacitadas no
deberán utilizar la máquina sin la
asistencia de una persona cualificada
o un médico.
10 Antes de utilizar este aparato,
realice un calentamiento con ejercicios
de estiramiento.
11 No utilice la bicicleta si no funciona
correctamente.
Precaución: Antes de comenzar a
utilizar la bicicleta, consulte a su
médico. Esta advertencia es
especialmente importante para
personas de edades superiores a
35 años o con problemas de salud.
Guarde estas instrucciones.
INDICACIONES GENERALES.-
1 Esta unidad esta diseñada para uso
doméstico. El peso de usuario no
debe exceder de 150Kg.
2 Los padres y otras personas
responsables de los niños deben de
tener en cuenta la naturaleza curiosa
de estos y que puede llevarles a
situaciones y conductas que pueden
resultar peligrosas.
Esta unidad no ha de utilizarse en
ningún caso como juguete.
3 Es responsabilidad del propietario
asegurarse que todos los usuarios de
la máquina estén adecuados e
informados sobre todas las
precauciones necesarias.
INSTRUCCIONES DE MONTAJE.-
Para el montaje de esta unidad se
recomienda la ayuda de otra persona.
Saque la unidad de la caja y
compruebe que tiene todas las piezas
Fig.1.
(13) Cuerpo principal; (1) Monitor; (3)
Manillar; (5) Arandela plana M10; (7)
Tija manillar; (84) Tija de sillín; (86)
Soporte horizontal sillin; (87) Sillín; (78)
Caballete trasero con tacos regulables;
(39) Caballete delantero con ruedas;
(60L) Pedal izquierdo; (60R) Pedal
derecho; (41) Tornillo c/ Alomada M10;
(43) Arandela plana M10; (44) Tuerca
ciega M10.
1. Coja el tubo caballete trasero (78) y
posiciónelo en el caballete trasero de
la maquina, como muestra la Fig.2, e
introduzca los tornillos (41), coloque
las arandelas planas (43), y las
tuercas ciegas (44), apriete
fuertemente.
2. Coja el tubo caballete delantero con
ruedas (39) y con las ruedas hacia
delante, como muestra la Fig.2,
introduzca los tornillos (41), coloque
las arandelas planas (43), y las
tuercas ciegas (44) y apriete
fuertemente.
3.- COLOCACIÓN DEL MANILLAR.-
Posicione el manillar (3) en la tija de
manillar (7), Fig.3, apriete el pomo (6)
con la arandela (5), seguido
introduzca el tubo del manillar (7) por
el agujero del tubo saliente del cuerpo
principal (13) Fig.3, posiciónelo y
apriete fuertemente el pomo (6) en
sentido de las agujas del reloj.
A continuación pase el cable que sale
del cuadro (13) a través del agujero
situado en la parte central del manillar
y conéctelo con el monitor (1).
Atornille el monitor (1) al manillar (3)
con los tornillos (2) incluidos con el
monitor y coloque el tapón (4) en el
agujero del manillar.
REGULACIÓN HORIZONTAL DEL
MANILLAR.-
Posicione el manillar (3) a la distancia
cómoda de realizar el ejercicio y
apriete el pomo (6) fuertemente Fig.3.
Manténgase dentro de las referencias.
REGULACIÓN VERTICAL DEL
MANILLAR.-
Posicione el manillar (3) a la distancia
cómoda de realizar el ejercicio sin
salirse de las referencias de 0-6 y
apriete el pomo (6) fuertemente Fig.3.
Manténgase dentro de las referencias
sin salirse de la marca “MIN INSERT”.
4.- MONTAJE DEL SILLÍN.-
Introduzca la abrazadera del sillín (87)
Fig.4, en el tubo horizontal de la tija
(86) como muestra la Fig.4, coloque el
sillín en posición y apriete las tuercas
de la abrazadera fuertemente.
Seguido introduzca el tubo horizontal
de la tija (86) por el agujero del tubo
de tija (84) Fig.4, posiciónelo y apriete
el pomo (6) Fig.4.
Introduzca la tija (84) por el tubo del
cuerpo principal (13) posiciónelo y fije
la tija del sillín en su posición cómoda
con el pomo de apriete (6) Fig.4 y
apriete en sentido de las agujas del
reloj.
REGULACIÓN DE LA ALTURA
SILLÍN.-
Aflojando un poco el pomo de apriete
(6) de tija en sentido contrario a las
agujas del reloj Fig.4, cuando lo tenga
a la altura adecuada para realizar el
ejercicio.
6
Apriete fuertemente el pomo (6) en el
sentido de las agujas del reloj.
Manténgase dentro de las referencias
sin salirse de la marca “MIN INSERT”.
REGULACIÓN HORIZONTAL DEL
SILLÍN.-
Aflojando un poco el pomo de apriete
(6) de tija en sentido contrario a las
agujas del reloj Fig.4, cuando lo tenga
a la medida adecuada para realizar el
ejercicio, apriete fuertemente el pomo
(6) en el sentido de las agujas del
reloj.
Manténgase dentro de las referencias
sin salirse de la marca “MIN INSERT”.
5.- MONTAJE DE LOS PEDALES.-
Siga atentamente las instrucciones de
montaje de los pedales, una
colocación incorrecta podría dañar la
rosca del pedal o de la biela.
La posición derecha e izquierda,
habrán de tomarse montado el usuario
en el sillín, en posición de hacer
ejercicio.
El pedal derecho (60R), marcado con
la letra (R), se enroscara en sentido
de giro agujas del reloj, en la biela
derecha, marcada con la letra (R).
Apriete fuertemente, Fig.5.
El pedal izquierdo (60L), marcado con
la letra (L), se enroscará en el sentido
contrario a las agujas del reloj, en la
biela izquierda, marcada con la letra
(L). Apriete fuertemente, Fig.5.
H9120.- REGULACIÓN DE
ESFUERZO.-
Para un control de esfuerzo regular de
su ejercicio, este aparato dispone de
un mando de tensión (74), colocado
en el tubo del cuerpo principal (13)
Fig.6A, que girándolo en el sentido de
las agujas del reloj le irá dando
distintas posiciones de resistencia.
Para aumentar la resistencia del
pedaleo usted gire el mando de
tensión (74), en sentido de las agujas
del reloj (+), hasta conseguir que el
esfuerzo de su ejercicio es el ideal
para usted.
Para disminuir la resistencia del
pedaleo, gire el mando de tensión
(74), en sentido contrario a las agujas
del reloj (-).
Importante:
El mando de tension (15) dispone de
un sistema de frenado de emergencia,
que apretando encima del mismo
fuertemente, como se indica en la
flecha de la Fig.6, se produce una
frenada más repentina para el volante.
NIVELACIÓN.-
Una vez colocada la unidad en su lugar
definitivo, para la realización del ejercicio,
compruebe que el asentamiento en el
suelo y su nivelación sean correctos.
Esto se conseguirá roscando más o
menos los pies regulables (47) como
muestra la Fig.7.
MOVIMIENTO Y ALMACENADO.-
La unidad está equipada con ruedas (14)
Fig.8, lo que hace más sencillo su
movimiento. Las ruedas que se
encuentran en la parte delantera de su
unidad, le facilitarán la maniobra de
colocar su unidad en el emplazamiento
escogido, levantando, ligeramente por la
parte delantera y empujando, como
muestra la Fig.8.
Guarde su máquina en un lugar seco
con las menores variaciones de
temperatura posible.
7
MANTENIMIENTO DE LA
MÁQUINA.-
Por razones higiénicas es necesario
que después de cada clase se limpie
el manillar y el asiento con un spray
de desinfección, así como eliminar el
sudor del cuadro de la bicicleta.
MANTENIMIENTO, 100 HORAS.-
1. APRIETE PEDALES.
Aunque los pedales van montados, el
pedal derecho (marcado con una R)
se monta atornillando en el sentido de
las agujas del reloj, y el pedal
izquierdo (marcado con una L), en el
sentido contrario.
Mantenimiento:
- Revisar la tensión de ajuste del pedal
a la cala regulando el tornillo de ajuste
mediante una llave Allen de 3mm.
- Aplicar un poco de aceite en la punta
de contacto de la cala con el pedal
para facilitar el encaje.
2. REVISIÓN, POMOS DE APRIETE.-
Los 4 pomos de apriete que dispone
la unidad se deberán aflojar y rociar
con un spray de engrase con el objeto
de garantizar la movilidad de los
mismos.
Para cualquier consulta, no dude en
ponerse en contacto con el
(S.A.T).Servicio de Asistencia
Técnica, llamando al teléfono de
atención al cliente (ver página final del
presente manual).
BH SE RESERVA EL DERECHO A
MODIFICAR LAS ESPECIFICACIONES DE SUS PRODUCTOS
SIN PREVIO AVISO.
8
English
IMPORTANT SAFETY ADVICE.-
PRECAUTIONS.
This bicycle has been designed and
constructed to provide maximum
safety. Nevertheless, certain
precautions should be taken when
using exercise equipment.
Read the whole manual before
assembling and using the bicycle. It
provides you with important
information about assembly, safety
and use of the machine.
The following safety precautions
should also be observed:
1 Keep children away from this
equipment at all times. DO NOT leave
them unsupervised in the room where
this bicycle is kept.
2 It can only be used by one person at
a time.
3 If you experience dizziness, nausea,
chest pains or any other symptom
while using this appliance STOP the
exercise. SEEK MEDICAL
ATTENTION IMMEDIATELY.
4 Use the appliance on a level, solid
surface. DO NOT use the bicycle
outdoors or close to water.
5 Keep your hands well away from
any of the moving parts.
6 Wear clothing suitable for doing
exercise. Do not use baggy clothing
that might get caught up in the bicycle.
Always wear running shoes or trainers
when using the machine. Make sure
all laces/cords are tied correctly.
7 This appliance must only be used for
the purposes described in this manual.
DO NOT use accessories that are not
recommended by the manufacturer.
8 Do not place sharp objects near the
machine.
9 Disabled people should not use the
machine without the assistance of a
qualified person or a doctor.
10 Do warm up stretching exercises
before using the equipment.
11 Do not use the bicycle if it is not
working correctly.
Caution: Consult your doctor before
beginning to use the bicycle. This
advice is especially important for those
over 35 or suffering from health
problems.
Keep these instructions safe for
future use.
GENERAL INSTRUCTIONS.-
1 This unit has been designed for
home use. The weight of the user must
not exceed 150 kg.
2 Parents and/or those responsible for
children should always take their
curious nature into account and how
this can often lead to hazardous
situations and behaviour resulting in
accidents.
Under no circumstances should this
appliance be used as a toy.
3 The owner is responsible for
ensuring that anyone who uses the
machine is duly informed about the
necessary precautions.
9
ASSEMBLY INSTRUCTIONS.-
The assistance of a second person is
recommended when assembling this
unit Take the unit out of its box and
make sure that all of the pieces are
there Fig.1:
(13) Main body; (1) Console; (3)
Handlebar; (5) Flat washer M10; (7)
Handlebar stem; (84) Saddle post;
(86) Horizontal saddle tube; (87)
Saddle; (78) Rear stabiliser bar with
adjustable feet; (39) Front stabiliser
bar with wheels; (60L) Left pedal;
(60R) Right pedal; (44) Slot head bolt
M10; (43) Flat washer M10; (41) Cap
nut M10.
1. Position the machine’s rear stand
on the rear stabilizer bar (78), as
shown in Fig.2, insert the bolts (44), fit
the flat washers (43) and cap nuts (41)
and then tighten securely.
2. Position the front stabiliser bar with
wheels (39), paying attention to the
red dots and with the wheels facing
forwards, as shown in Fig.2, insert the
bolts (44), fit the flat washers (43) and
cap nuts (41) and tighten securely.
3.- FITTING THE HANDLEBAR.-
Position the handlebar (3) on the
handlebar stem (7), Fig.3, tighten the
knob (6) with (5) Flat washer and then
insert the handlebar stem (7) into the
hole on the main body (13), Fig.3.
Position it correctly and then tighten
knob (6) by turning it clockwise.
Then pass lower monitor cable
through the hole on the handlebar (3),
and connect it to monitor (1). Fasten
monitor onto the handlebar (3) with
screws (2) which are pre-assembled
on the back of monitor and then fit
plug (4) onto the hole on the
handlebar (3).
ADJUSTING THE HANDLEBAR
HORIZONTALLY.-
Position the handlebar (3) at a
comfortable distance for doing
exercise, now tighten knob (6)
securely, Fig.3.
Stay within the references.
ADJUSTING THE HANDLEBAR
VERTICALLY.-
Position the handlebar (3) at a
comfortable distance for doing
exercise, now tighten knob (6)
securely, Fig.3.
Stay within the references without
going beyond the “MIN INSERT” mark.
4.- ATTACHING THE SADDLE.-
Fit the saddle bracket (87), Fig.4, onto
the horizontal saddle tube (84), as
shown in Fig.4, fit the saddle into
position and tighten the nuts on the
bracket securely.
Insert the saddle post (84) into the
boss on the main body (13), position it
correctly and tighten the saddle post
by using the adjustment knob (6),
Fig.4, turning it clockwise.
ADJUSTING THE SADDLE HEIGHT.-
Loosen the saddle post adjustment
knob (6) slightly by turning it
anticlockwise, Fig.4, move the saddle
to a position comfortable for doing
exercise and then tighten the
adjustment knob (6) securely by turning
it clockwise.
Stay within the references without
going beyond the “MIN INSERT” mark.
10
HORIZONTAL ADJUSTMENT OF
THE SADDLE.-
Loosen the knob (6) slightly by turning
it anticlockwise, Fig.4, move the
saddle to a position comfortable for
doing exercise and then tighten the
knob (6) securely by turning it
clockwise.
Stay within the references without
going beyond the “MIN INSERT” mark.
5.- FITTING THE PEDALS.-
The assembly instructions for the
pedals must be followed to the letter,
fitting these incorrectly could damage
the screw thread on either the pedal or
the crank.
Right and left refer to the position that
the user adopts when sitting on the
saddle to do the exercises.
The right-hand pedal (60R), marked
with the letter (R), screws onto the
right-hand crank, also marked with an
(R), in a clockwise direction. Tighten
securely, Fig.5.
The left-hand pedal (60L), marked with
the letter (L), screws onto the left-hand
crank, also marked with an (L), in an
anti-clockwise direction. Tighten
securely, Fig.5.
H9120.- EXERTION SETTINGS.-
To provide an even level of exertion
during exercise, this appliance is
equipped with a tensioning control
(74), located on the stem of the main
body (13), Fig.6A. This provides
various exertion settings when turned
clockwise.
To increase pedal resistance turn the
tensioning control (74) clockwise (+)
until the exertion level best suits your
exercise requirements.
To reduce pedal resistance turn the
tensioning control (74) anticlockwise (-).
11
Important:
The tensioning control (15) is
equipped with an emergency braking
system which, when applied with force
(as shown by the arrow in Fig.6,
produces a much sharper braking
effect.
LEVELLING.-
Once the unit has been placed into its
final position, make sure that it sits flat
on the floor and that it is level. This
can be achieved by screwing the
adjustable feet (47) up or down, as
shown in Fig.7.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (14)
Fig.8, to make it easier to move. The
wheels located at the front of your unit
make it easier to move it into a chosen
position, by lifting the rear of the unit
up slightly and pushing it, as shown in
Fig.8. Store your unit in a dry place,
preferably not subject to changes in
temperature.
MAINTAINING THE MACHINE.-
For health reasons it is necessary to
clean the handlebars and seat after
each class with a disinfectant spray,
as well as removing any sweat from
the bicycle’s frame.
MAINTENANCE EVERY 100
HOURS.-
1. TIGHTENING THE PEDALS.
Even though the pedals are already
fitted, the right-hand pedal (marked R)
screws on in a clockwise direction,
whereas the left-hand pedal (marked
L) does so in the opposite direction.
Maintenance:
-The tension of the pedal clip with the
pedal should be checked weekly,
using a 3mm allen key to adjust the
set screw.
-Apply a little oil to the contact point of
the pedal clip with the pedal to ensure
that it locks on.
2. CHECKING THE TIGHTENING
KNOBS.-
The 3 tightening knobs should be
loosened off and sprayed with a
lubricant to ensure that they remain
operative.
Do not hesitate to get touch with the
Technical Assistance Service if you
have any queries by phoning customer
services (see last page in manual).
BH RESERVES THE RIGHT TO
MODIFY THE SPECIFICATIONS OF
ITS PRODUCTS WITHOUT PRIOR
NOTICE.
12
Loading...
+ 26 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.