Antes de comenzar cualquier
programa de ejercicio, consulte a su
médico. Se recomienda la realización
de un examen físico completo.
Trabaje en el nivel de ejercicio
recomendado, no llegue al
agotamiento. Si siente dolor o
molestias de cualquier tipo, pare el
ejercicio inmediatamente y acuda a su
médico.
Utilice el aparato sobre una superficie
sólida y nivelada, con algún tipo de
protección para el suelo o alfombra.
Por razones de seguridad, el equipo
deberá disponer a su alrededor de un
espacio libre no inferior a 0,5 m.
No permita a los niños jugar con este
aparato o a su alrededor. Mantenga
las manos alejadas de las partes en
movimiento.
Compruebe la elíptica antes de
comenzar el ejercicio, para
asegurarse de que se han montado
todas las piezas y que las tuercas,
tornillos, pedales y brazos se han
apretado correctamente antes del uso.
Utilice prendas y calzado apropiados
para el ejercicio físico. No utilice
prendas sueltas. No utilice calzado
con suela de cuero o tacones altos.
Este aparato ha sido probado y
cumple con la norma EN957
adecuado sólo para uso doméstico. El
frenado es independiente de la
velocidad.
IMPORTANTE.-
Lea las instrucciones detenidamente
antes de proceder con el montaje.
Retire todas las partes del cartón de
embalaje e identifíquelas con respecto
al listado, para asegurarse de que no
falta ninguna.
No elimine el cartón hasta haber
montado la elíptica completamente.
Utilice el aparato siempre de acuerdo
con las instrucciones. Si encuentra
algún componente defectuoso durante el montaje o comprobación del
aparato, o si oye algún ruido extraño
durante la utilización, pare.
No utilice este aparato hasta que se
haya solucionado el problema.
INSTRUCCIONES PARA EL
EJERCICIO.-
El uso de la bicicleta elíptica le
reportará diferentes beneficios,
mejorará su condición física, tono
muscular y, junto con una dieta baja
en calorías, le ayudará a perder peso.
1. La fase de calentamiento.
Esta fase acelera la circulación
sanguínea en el cuerpo y pone a tono
los músculos para el ejercicio.
También reduce el riesgo de
calambres y lesiones musculares. Es
aconsejable realizar algunos ejercicios
de estiramiento, según se muestra
más adelante. Realice cada
estiramiento aproximadamente
durante 30 segundos, no fuerce los
músculos. Si siente dolor, PARE.
7
2. La fase de ejercicio.
En esta fase se realiza el esfuerzo más
importante. Tras el ejercicio regular, los
músculos de las piernas aumentarán
su flexibilidad. Es muy importante
mantener un ritmo constante. El ritmo
de ejercicio será lo bastante alto para
aumentar las pulsaciones hasta la
zona objetivo que se muestra en el
gráfico siguiente.
Esta fase debería durar un mínimo de
12 minutos aunque se recomienda a
la mayoría de la gente comenzar con
períodos de 10-15 minutos.
3. La fase de relajación.
Esta fase permite la relajación del
sistema cardio-vascular y muscular.
Se trata de una repetición de los
ejercicios de calentamiento, por
ejemplo, reduciendo el ritmo, y
continuando aproximadamente 5
minutos. Repita los ejercicios de
estiramiento, y recuerde no forzar los
músculos. Según transcurran los días,
necesitará entrenamiento más
prolongados y de mayor intensidad.
Es recomendable ejercitarse un
mínimo de tres días por semana, en
días alternos.
Tonificación muscular.
Para tonificar los músculos durante el
ejercicio deberá seleccionar una
resistencia alta. Esto implicará una
mayor tensión sobre la musculatura de
las piernas y quizás deba reducir el
tiempo del ejercicio. Si también desea
mejorar su forma física general, deberá
cambiar su programa de
entrenamiento. Realice los ejercicios
de calentamiento y relajación de
costumbre, pero cuando esté llegando
al fiinal de la fase de ejercicio, aumente
la resistencia para someter sus piernas
a un mayor esfuerzo. Deberá reducir la
velocidad para mantener el ritmo
cardíaco en la zona objetivo.
Pérdida de peso.
En este caso, el factor importante es
el esfuerzo realizado. Cuando más
intenso y más prolongado sea el
trabajo, mayor será la cantidad de
calorías quemadas. Efectivamente, el
trabajo es el mismo que se realiza
para mejorar la condición físico, pero
el objetivo es diferente.
INDICACIONES GENERALES.-
Lea atentamente las instrucciones de
este manual. Este le da indicaciones
importantes sobre el montaje,
seguridad y uso de la máquina.
1 Esta unidad esta diseñada para uso
semi profesional. El peso de usuario
no debe exceder de 130Kg.
2 Mantenga las manos alejadas de
cualquiera de las partes móviles de la
unidad.
3 Los padres y otras personas
responsables de los niños deben de
tener en cuenta la naturaleza curiosa
de estos y que puede llevarles a
situaciones y conductas que pueden
resultar peligrosas. Esta unidad no ha
de utilizarse en ningún caso como
juguete.
4 Es responsabilidad del propietario
asegurarse que todos los usuarios de
la máquina estén adecuados e
informados sobre todas las
precauciones necesarias.
8
5 Su unidad sólo puede ser usada por
una persona al mismo tiempo.
6 Utilice prendas de vestir y calzado
adecuado. Átese los cordones
correctamente.
INSTRUCCIONES DE MONTAJE.-
1. Saque la unidad de la caja y
compruebe que tiene todas las piezas.
ATENCION: Se recomienda la
ayuda de una segunda persona,
para la realización del montaje de
esta máquina.
Fig.1 Piecerio
(1) Monitor.
(4) Tubo de remo.
(20) Tubo de remo izquierda (L).
(25) Carcasa bastón izqdo(trasera) .
(29) Carcasa bastón izqdo(frontal).
(32) Tubo de remo derecha (R).
(33) Carcasa bastón drcho(frontal).
(34) Carcasa bastón drcho(trasero).
(35) Tubo manillar.
(72) Cuerpo central.
(143) P
(146) Carcasa protección brida.
(147) Tapa tubo de remo derecha (R).
(148) Tapa tubo de remo izquierda (L).
(149) Tapas cierre eje giro bastones
(L)
(150) Tapas cierre eje giro bastones
(R)
(158) Transformador.
(174) Chasis del tubo de remo.
Fig.2 Tornilleria
(3) Tornillos de M-8x16.
(23) Tornillos de M-4x40.
(51) Tornillos de M-5x110.
(151) Tornillos allen alomada M-8x55.
(152) Tornillos de M-3x16.
(153) Tuercas autoblocantes de M-8.
(154) Arandelas M8 Ø 16.
(155) Arandelas M8 Ø 16.
2 Llave de tubo combinada.
Llave de allen.
ortabotellín
2. MONTAJE DEL CHASIS.-
Pase el cable (73) a través del tubo de
remo (174) utilizando la guía (178).
Introduzca el chasis del tubo de remo
(174) en el
tubo saliente del cuerpo central (72)
en dirección a la flecha, Fig.3,
teniendo cuidado de no pillar los
cables. Coloque los tornillos (175)
junto con, las arandelas (176) y las
arandelas (177) y apriete fuertemente.
Fig 4
3. MONTAJE DEL TUBO REMO.-
Introduzca el brazo izquierdo (20) en
el eje giro brazos (10) Fig.5, a
continuación coloque el brazo derecho
(32) en el otro extremo del eje giro
brazos, coloque en los extremos del
eje los tornillos (13) y las arandelas
planas (12) y apriete fuertemente.
Coja las tapas (33) y (34) marcadas
en el interior con la letra (R), y
posicionelas en el extremo del eje con
los brazos en la parte derecha, según
muestra la Fig.5 a continuación,
atorníllelas con los tornillos (23) y
(24).
Realice el mismo montaje en el otro
extremo del eje con las tapas (25) y
(29) marcadas en el interior con la
letra (L).
Asegúrese que los casquillos (11)
están colocados en la posición
correcta. Fig 5.
Coja el tubo de remo (4) y suelte los
tornillos (15) de la parte inferior del
tubo junto con las arandelas
onduladas (16) y las arandelas de
muelle (17) Fig.5.
Seguido acerque el tubo de remo (4)
al tubo saliente del cuerpo central
(174), Fig.5, conexione los terminales
9
(73) y los terminales (19) Fig.5.
Introduzca el tubo de remo (4) en el
tubo saliente, del cuerpo central (174)
en dirección a la flecha, Fig.5,
teniendo cuidado de no pillar los
cables.
Coloque los tornillos (15) que acaba
de soltar del remo junto con, las
arandelas (16) y las arandelas de
muelle (17) y apriete fuertemente.
A continuacion posicione la tapa lateral
(149) y (150) , hacia el triangulo inferior
del cuerpo principal (174), Atornille la
tapa con los tornillos (75).
ATENCION: Es aconsejable el
reapretar los tornillos que se
acaban de montar al mes de uso de
la máquina.
4. MONTAJE DE LOS TUBOS DE
PIES.-
Coja el pie izquierdo (50), y posiciónelo
en la “U” de la parte inferior del brazo
izquierdo (20), Fig.6.
Introduzca el tornillo (151) como de
indica en la Fig.6 y coja la arandela
plana (154) y la tuerca autoblocante
(153) y apriete fuertemente.
Coja el pie derecho (61), y realice el
mismo montaje que ha realizado para
el montaje del pie izquierdo.
5. MONTAJE DE LAS TAPAS
LATERALES DEL EJE GIRO DE
BRAZOS CON LOS PIES.-
Coja las tapas (147 y 148) marcadas
en el interior con la letra (R), y
posicionelas en el extremo de los
tubos de pies con la parte inferior de
los brazos en la parte derecha, según
muestra la Fig.6 a continuación
atornillelas con los tornillos (152) y
(51).Realice el mismo montaje con las
tapas (147 y 148) marcadas en el
interior con la letra (L).
A continuación suelte los tornillos (5 y
9) del mástil central (4) y coja el porta
botellines (143) e introdúzcalo por la
parte superior del mástil (4) en
dirección de la flecha. Fig 7.
Sujételo con los tornillos (5 y 9)
soltados anteriormente. Fig 7.
6.- COLOCACIÓN DEL
MANILLAR.-
Posicione el manillar (35) en el tubo
de manillar (4), Fig.7, introduzca el
cable del hand-grip (40) por la ranura
como muestra en la Fig.7, y sáquelo
por la parte superior del tubo manillar.
Coloque el tornillo (156), meta la
arandela (157) coloque la tapa
protección de brida (146).
7.- MONTAJE DEL MONITOR.-
Suelte los tornillos (3) y arandelas (155)
de la parte trasera del monitor. Seguido
coloque el monitor en dirección de la
flecha sobre la chapa (2) Fig.8,
introduciendo los cables en el interior
del tubo remo y teniendo cuidado de no
pillar los cables. Coloque los tornillos (3)
y arandelas (155) soltados
anteriormente.
Conexione los dos terminales que
salen del tubo manillar (35) y del
monitor (1), figura 8.
Introduzca el monitor (1) en el tubo
manillar (35), como indica la figura 8
teniendo cuidado de no pillar los
cables. Coloque los tornillos (3) con
las arandelas, y apriete fuertemente,
todos los tornillos.
10
NIVELACIÓN.-
Una vez colocada la unidad en su
lugar definitivo, para la realización del
ejercicio, compruebe que el
asentamiento en el suelo y su
nivelación sean correctos. Esto se
conseguirá roscando más o menos los
pies regulables (86) como muestra la
Fig.9.
MOVIMIENTO Y ALMACENADO.-
La unidad está equipada con ruedas
(83) como muestra la Fig.10 lo que
hace más sencillo su movimiento. Las
ruedas que se encuentran en la parte
delantera de su unidad, le facilitarán la
maniobra de colocar su unidad en el
emplazamiento escogido, levantando,
ligeramente por la parte trasera.
Guarde su máquina en un lugar seco
con las menores variaciones de
temperatura posible.
CONEXIÓN A LA RED.-
Introduzca la clavija de enganche (m),
del transformador (158) en el punto de
conexión (k), del cuerpo central, (parte
trasera inferior) Fig.11 y conecte el
transformador (158) de corriente a la
red de 230 v, Fig.11.
Para cualquier consulta, no dude en
ponerse en contacto con el
(S.A.T).Servicio de Asistencia Técnica,
llamando al teléfono de atención al
cliente (ver página final del presente
manual).
BH SE RESERVA EL DERECHO A
MODIFICAR LAS
ESPECIFICACIONES DE SUS
PRODUCTOS SIN PREVIO AVISO.
11
English
SAFETY INSTRUCTIONS.-
Consult your doctor before starting
any exercise program. It is advisable
to undergo a complete physical
examination. Work at the
recommended exercise level, do not
overexert yourself. If you feel any pain
or discomfort, stop exercising
immediately and consult your doctor.
Use the appliance on a solid, flat
surface, with some type of protection
for the floor or carpet. In the interest of
safety, the equipment must have at
least 0.5 metres of free space around
it. Do not allow children to play with
the equipment or in the immediate
vicinity. Keep your hands well away
from any of the moving parts. Check
the elliptical trainer before starting the
exercise; to make sure that all of the
parts are attached and that the nuts,
bolts, pedals and focus bars have
been tightened correctly prior to use.
Wear appropriate clothing and
footwear for the exercise. Do not use
loose clothing. Do not wear leather
soled shoes or footwear with high
heels.
This appliance has been tested and it
complies with standard EN957,
suitable for home use. Braking is
independent of speed.
IMPORTANT.
Read the instructions carefully before
proceeding to assemble the
equipment.
Remove all the parts from the
cardboard packaging and check them
against the parts list to ensure that
there is nothing missing.
Do not throw the cardboard away until
the elliptical trainer is fully assembled.
Always use the appliance in
accordance with the instructions. If
you discover any defective component
while assembling or checking the
equipment, or if you hear any strange
noise during exercise then stop. Do
not use the appliance until the
problem has been resolved.
EXERCISE INSTRUCTIONS.-
Use of the ELLIPTICAL TRAINER
offers various benefits; it will improve
fitness, muscle tone and when used in
conjunction with a calorie controlled
diet it will help you to lose weight.
1. Warm-up phase.
This phase speeds up the body’s
blood circulation and gets the muscles
ready for exercise. It also reduces the
risk of cramp and sprains. It is
advisable to do some stretching
exercises, as shown below. Each
stretch should last approximately 30
seconds, do not overexert the
muscles. If you feel pain, STOP.
2. Exercise phase.
This phase requires the greatest
physical exertion. After regular
exercise the leg muscles will become
more flexible. It is important to keep
the rhythm constant.
12
The rhythm of the exercise should be
fast enough to bring the heart rate into
the target area, as shown on the
following graph:
This phase should last at least 12
minutes, although it is advisable for
most people to start off with sessions
of 10-15 minutes.
3. Cool-down phase.
This phase allows the cardiovascular
and muscle system to relax. It consists
of repeating the warm-up exercises,
i.e. reducing the rhythm and
continuing for approximately 5
minutes. Repeat the stretching
exercises but remember not to
overexert the muscles. Eventually
your training sessions will have to
become longer and more intensive. It
is advisable to exercise at least three
days per week, on alternate days.
Muscle toning.
You should select a high exertion level
in order to tone muscles during
exercise. This entails greater stress on
the leg muscles, so it may be wise to
reduce exercise times. If you also wish
to improve your overall fitness then
you should change your training
program. Do the warm-up and cooldown exercises as normal but when
you are reaching the end of the
exercise phase, increase the exertion
level in order to make your legs work
harder. You should reduce speed in
order to keep your heart rate within
the target area.
Weight loss.
In this case the important factor is the
effort made. The more intense and the
longer the session, the greater the
number of calories burned. Even
though you are dong the same work
as you do to improve fi tness, the
objective has changed.
GENERAL INSTRUCTIONS.-
Carefully read through the instructions
contained in this manual. It provides
you with important informa- tion about
assembly, safety and use of the
machine.
1
This unit has been designed for
home use.The user weight does not
have to exceed 130Kg.
2
Keep your hands well away from
any of the moving parts.
3
Parents and/or those responsible for
children should always take their
curious nature into account and how
this can often lead to hazardous
situations and behaviour resulting in
accidents. This unit does not have to
be used in any case like toy.
4
The owner is responsible for
ensuring that anyone who uses the
machine is duly informed about the
necessary precautions.
5
Your unit can only be used by one
person at a time.
6
Use suitable clothing and footwear.
tie up your shoelace correctly
ASSEMBLY INSTRUCTIONS.-
1.
Take the unit out of its box and
make sure that all of the pieces are
there:
ATTENTION: The assistance of a
second person is recommended
when assembling this machine.
13
Fig.1 Parts list
(1) Monitor.
(4) Main post.
(20) Upper handlebar (left)
(25) Cover for left upper
handlebar(rear).
(29) Cover for left upper
handlebar(front).
(32) Upper handlebar (Right).
(33) Cover for right upper
handlebar(front).
(34) Cover for right upper
handlebar(rear)
(35) Handlebar stem.
(72) Main body.
(143) B
ottle
holder.
(146) Bracket cover.
(147) Focus bar spindle covers (L).
(148) Focus bar spindle covers (R).
(149) Covers main post left (L).
(150) Covers main post right (R).
(158) Transformer.
(174) Front frame.
Pass the cable (73) through the main
post (174) using the guide (178). Bring
the main post (174) up to the boss on
the main body (72) in the direction of
the arrow, Fig.3, making sure not to
snag any of the cables.
Drive the screws (175) together with
the washers (176) and washers (177)
and tighten securely.fig4.
3. FITTING THE MAIN POST.-
Insert the left focus bar (20) onto the
focus bar spindle (10), Fig.5, then fit
the right focus bar (32) on the other
end of the spindle. Fit the bolts (13)
and the flat washers (12) and tighten
securely. Take the covers (33) (34),
and position them at the spindle end
with the bars on the right hand side,
as shown in Fig.5. Now use screws
and (23) (24) to attach them. Carry out
the same procedure at the other end
of the bar using the covers (25) (29)
marked on the inside with the letter
“L”.
Be sure that the bushes (11) are in
the correct position. Fig 5.
Take the main post (4) and remove
the screws (15) the corrugated
washers (16) and spring washers (17)
from the bottom of the post. Fig.5.
Next, bring the main post (4) up to
boss on the main body (174), Fig.3,
connect the terminals (73) and (19),
Fig.5.
Slip the main post (4) over the boss
(D) on the main body (174) in the
direction of the arrow, Fig.5, making
sure not to snag any of the cables.
Refit the screws (15), the washers
(16) and the spring washers (17) that
you removed previously, and tighten
securely.
Next, position the side cover (149) and
(150) so that it faces the bottom
triangle on the main body (72) and
secure the cover using screws (75).
ATTENTION: It is advisable to
retighten these screws after one
month of using the machine.
14
4. FITTING THE FOOT BARS.-
Take the left foot bar (50) and position
it on the “U” at the bottom of the left
focus bar (20), Fig.6.
Insert screw (151), as shown in Fig.6,
then fit the flat washer (154) and the
self locking nut (153), and tighten
securely. Take the right foot bar (61)
and go through the same assembly
procedure as with the left.
5. FITTING THE FOCUS BAR
SIDE COVERS TO THE FOOT
BARS.-
Take the covers (147 and 148),
marked on the inside with the letter
“R”, and position them at the end of
the foot bars with the inside of the
focus bars on the right hand side, as
shown in Fig.6. Now use screws (152)
and (51) to attach them.
Carry out the same procedure using
the covers (147 and 148) marked on
the inside with the letter “L”.
Next, release the screws (5 and 9) of
the main post (4), take bottle holder
(143), and insert it in through the top
of the post (4) in the direction of the
arrow.fig7. Attach the bottle holder
using screws (5 and 9) previously
removed. fig 7.
6. FITTING THE HANDLEBAR.-
Bring the handlebar (35) up to the
handlebar stem (4), Fig.7, insert the
hand-grip cable (49) in through the
slot as shown in Fig.7, and pull it out
through the top of the handlebar stem.
Insert screw (156), put the washer
(157), then fit the bracket cover (146).
7. FITTING THE ELECTRONIC
MONITOR.-
Release screws (41) at the back of the
monitor.
Next, slide the front of the monitor onto
the plate (2) in the direction of the
arrow, Fig.8, push the cables down into
the main post making sure not the
pinch any of the cables.
Replace the screws (41) removed
previously.
Bring the monitor (1) to the handlebar
stem (35) figure 8, connect the two
terminals coming out of the handlebar
stem (35) and the monitor (1), figure 8.
Insert the monitor (1) onto the
handlebar stem (4), as shown in Fig.8,
making sure not to pinch any of the
cables. Fit the bolts (3) along with the
flat washers, securely tighten.
LEVELLING.-
Once the unit has been placed into its
final position, make sure that it sits flat
on the floor and that it is level. This
can be achieved by screwing the
adjustable feet (86) up or down, as
shown in Fig.9.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (83),
as shown in Fig.10, which make it
easier to move. The two wheels at the
front of the unit make it easier to place
the unit in to any chosen position by
lifting the rear slightly.
Store your unit in a dry place,
preferably not subject to changes in
temperature.
15
Loading...
+ 34 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.