IP VIDEO SURVEILLANCE
Operation User Manual
IP Video Door Station
DS06M(P)
net
Electronic Motorized Lock Control
Multiaccessible User Operation
Built-in IP Video Camera
Two-Way Audio
Table of Contents
IP Video Door Station DS06M(P) Operation User Manual
1
Table of Contents
CHAPTER 1. SAFETY INSTRUCTIONS ........................................................................................... 3
CHAPTER 2. GENERAL INFO ......................................................................................................... 5
2.1. BEWARD DS06M(P) DOOR STATION OVERVIEW .................................................................... 5
2.1.1. Key Features ................................................................................................................ 6
2.1.2. Package Contents ........................................................................................................ 6
2.1.3. Default Settings ............................................................................................................ 6
2.2. PURPOSE OF THIS MANUAL..................................................................................................... 7
2.3. MINIMUM SYSTEM REQUIREMENTS ......................................................................................... 8
CHAPTER 3. GETTING STARTED ................................................................................................... 9
3.1. INSTALLATION OF ACTIVEX COMPONENTS AND AUTHORIZATION ............................................... 9
3.2. MAIN WINDOW (LIVE VIEW) .................................................................................................. 13
CHAPTER 4. REPLAY .................................................................................................................... 16
CHAPTER 5. CONFIG: LOCAL CONFIG ....................................................................................... 18
CHAPTER 6. CONFIG: AUDIO ....................................................................................................... 19
CHAPTER 7. CONFIG: VIDEO ....................................................................................................... 20
7.1. ON-SCREEN TEXT ................................................................................................................ 20
7.2. VIDEO CODING .................................................................................................................... 21
7.3. PRIVACY MASK .................................................................................................................... 23
7.4. IMAGE ................................................................................................................................. 24
CHAPTER 8. CONFIG: NETWORK SETTINGS ............................................................................. 27
8.1. BASIC.................................................................................................................................. 27
8.2. LAN .................................................................................................................................... 28
8.3. PPPOE ............................................................................................................................... 29
8.4 UPNP .................................................................................................................................. 30
8.5. E-MAIL ................................................................................................................................ 31
8.6. FTP .................................................................................................................................... 32
8.7. DDNS ................................................................................................................................. 33
8.8. PPTP ................................................................................................................................. 34
8.9. RTSP ................................................................................................................................. 34
8.10. HTTPS ............................................................................................................................. 36
8.11. SIP ................................................................................................................................... 38
8.12. MODBUS ........................................................................................................................... 41
8.13. CAMDRIVE ........................................................................................................................ 42
8.14. HTTP EVENT ..................................................................................................................... 44
CHAPTER 9. CONFIG: RECORD SETTINGS ................................................................................ 47
9.1. MEMORY CARD .................................................................................................................... 47
9.2. VIDEO RECORDING .............................................................................................................. 48
9.3. SNAPSHOTTING ................................................................................................................... 49
CHAPTER 10. CONFIG: ALARM SETTINGS ................................................................................. 50
10.1. MOTION DETECTION SETTINGS ........................................................................................... 50
10.2. CALL BUTTON .................................................................................................................... 52
10.3. CONNECTION LOSS ............................................................................................................ 53
CHAPTER 11. CONFIG: CONTROLLER ........................................................................................ 54
CHAPTER 12. CONFIG: FACIAL RECOGNITION ......................................................................... 56
12.1. SETTINGS .......................................................................................................................... 57
12.2. FACE IMAGE DATABASE ...................................................................................................... 58
12.3.EVENTS ............................................................................................................................. 60
CHAPTER 13. CONFIG: SYSTEM .................................................................................................. 61
13.1. SYSTEM INFO .................................................................................................................... 61
13.2. SYSTEM TIME .................................................................................................................... 62
13.3. ACCESS POLICY ................................................................................................................. 63
13.4. UPGRADE .......................................................................................................................... 64
Table of Contents
IP Video Door Station DS06M(P) Operation User Manual
2
13.5. RESTORE .......................................................................................................................... 66
13.6. REBOOT ............................................................................................................................ 67
13.7. SYSTEM LOG ..................................................................................................................... 68
CHAPTER 14. ALARM .................................................................................................................. 69
CHAPTER 15. RECOMMENDATIONS ON SETTING AND OPERATION OF DS06M(P) ............... 70
15.1. ACOUSTIC ECHO CANCELLATION ........................................................................................ 70
15.2. SOUND GAIN AND VOLUME ADJUSTING ................................................................................ 71
APPENDICES ................................................................................................................................. 72
APPENDIX А. FACTORY DEFAULTS ............................................................................................... 72
APPENDIX B. MAINTENANCE ................................................................ ........................................ 72
APPENDIX C. SIP SETTINGS EXAMPLE .......................................................................................... 73
C1. Direct Connection .......................................................................................................... 73
C2. SIP Server ..................................................................................................................... 75
APPENDIX D. SIP HARDWARE AND SOFTWARE (FOR TRANSMITTING VIDEO AND SOUND VIA SIP)
COMPATIBILITY LISTS ................................ ............................................................................................ 78
D1. PBX Compatibility .......................................................................................................... 78
D2. Software Compatibility ................................................................................................... 78
D3. Hardware Compatibility .................................................................................................. 78
APPENDIX E. GLOSSARY ............................................................................................................. 79
Chapter 1. Safety Instructions
IP Video Door Station DS06M(P) Operation User Manual
3
ATTENTION!
Use accessories specified by the manufacturer only. Use of improper accessories may case device
breakdown.
ATTENTION!
Contact out Service Center in case of malfunction.
Chapter 1. Safety Instructions
Before using the product.
This product complies with all safety rules. However, improper use of any electric device
can cause fires and severe damage. In order to avoid accidents, please read this Manual carefully
before you start using this door
Follow this Operation Manual.
Do not use or store the door station in severe environment:
Avoid extremely low and high temperatures (The operating temperature of this door
station is -40°~+50°).
Avoid prolonged exposure to direct sunlight, do not install near water and heat sources.
Do not install near electromagnetic transmitters
Avoid exposure to high vibration.
In case of:
Smoke or strange smell coming from the door station.
Water or foreign matter getting inside the door station.
The door station getting damaged:
Do the following:
Unplug the power cord and disconnect all other cords from the door station.
Contact our Service Center. You can find our contact information on our website:
http://www.beward.ru/.
Chapter 1. Safety Instructions
IP Video Door Station DS06M(P) Operation User Manual
4
Transportation
Transport the door station carefully, using the original box and protective packing
Air flow
In order to avoid overheating, ensure that nothing is blocking the air circulation around the
door station!
Cleaning
Use a soft dry cloth to clean the surface of the device. To remove obstinate stains, apply a
small amount of detergent on the cloth, then wipe the surface dry
Do not use volatile solvents (alcohol-containing products, Benzene etc.) to avoid damaging
the door station housing.
Chapter 2. General Info
IP Video Door Station DS06M(P) Operation User Manual
5
Chapter 2. General Info
2.1. BEWARD DS06M(P) door station overview
DS06M(P) IP Video Door Station is designed for organizing IP intercome systems based on
already existing local networks without using any additional equipment (e.g. separate internal
monitors). To start using the door station you only have to install the software from the disk and set
it up. Low cost, easy installation and remote access to the device . This device is:
Low-cost
Easy to install
Remote Access Supported
Pic. 2.1
DS06M(P) has build-in microphone, speaker, video camera, Infrared LED and a call button,
as well as vandal-resistant housing. The device allows establishing video and audio connection
between the Guest and the Client, conducting surveillance of the nearby territory, control of other
devices that are connected to the door station (electronic locks, garage door openers, light
switches, alarm systems etc.) Infrared LED (with work distance up to 10 m) and the mechanical
infrared filter allow conducting video surveillance in low-light level environments. The device is
supported by modern network technologies, allowing it to be used a part of a complex IP
Surveilance system.
DS06M Door station is connected to the network via-T/100BASE-TX Ethernet interface. Its
power is supplied from a DC 12V power source. The device also supports PoE.
The device is even more reliable due to its SD card support that prevents loss of data in
case of network failures
Chapter 2. General Info
IP Video Door Station DS06M(P) Operation User Manual
6
ATTENTION!
Package contents and device specification are subject to change without notice
2.1.1. Key Features
Image sensor: 1.3 MP, CMOS 1/3'' SONY ExmorTM, Day/Night
Simultaneous encoding: H.264/H264, H.264/MJPEG, MJPEG /MJPEG
Framerate: Up to 25 fps (all resolutions)
IR Illumination (distance up to 10 m) and a mechanical IR filter
4GB MicroSDHC memory card installed (up to 32GB supported)
Multistreaming: up to 10 unique streams (only one user can be in the two-way audio
mode at one time)
Built-in web server for viewing and adjusting settings
Built-in player for recorded videos
Build-in microphone and speaker
Power: DC 12 , 0.5 A / PoE 802.3af Class 0 (for DS06MP only)
Temperature: -40°С~+50°С
Supported protocols: TCP/IP, SIP v.2.0, PPTP, HTTP, HTTPS, FTP, SMTP, DDNS,
DHCP, PPPoE, RTP, RTSP, UPnP, UDP, NTP, ONVIF v.2.41, Modbus TCP, Camdrive
ONVIF v.2.41 support
2.1.2. Package contents
DS06M(P) Door station
Bracket with mounting kit
Security screw with L- key
NC103 / NC103P / NC311P controller
RJ45-S01 (2 pcs.)
Terminal block
CD with software and documentation
2.1.3. Default Settings
IP address: 192.168.0.99
Subnet Mask: 255.255.255.0
Gateway: 192.168.0.1
Username: admin
Password: admin
HTTP port: 80
Chapter 2. General Info
IP Video Door Station DS06M(P) Operation User Manual
7
Data Port: 5000
2.2. Purpose of this Manual
BEWARD DS06M(P) door station can be used as a video surveillance device with a built-in
web server and a web interface.
You can view the video broadcast by this device via the standard internet browser or via the
free software included in the CD (Also can be downloaded from App Store and Play Market).
This User Manual contains the full information on how to operate the door station via the
web interface. It explains how to set up the web interface for use in local network or the Internet.
To learn more about using the door station software, please read the Software User Manuals
Despite the fact the several functions are only available in Beward Software (see BEWARD
Intercom Software Operation Manual), the web version allows users to operate the door station
from any location with Internet access
This Manual contain the information needed to use the DS06M(P) Door Station without
installing additional software.
Chapter 2. General Info
IP Video Door Station DS06M(P) Operation User Manual
8
Item
Requirement
CPU
2.8 Ghz Intel Core or AMD Athlon X2
Video Card
256 mb RAM or similar
RAM
1 Gb (2Gb or higher recommended)
OS
Microsoft ® Windows Vista, Windows 7, Windows 8
Internet Browser
Internet Explorer 11.0 or higher
ATTENTION!
Windows 7 Professional и Internet Explorer 11.0 are used in this Manual (though in some screenshots
other OS and browser version may be depicted). In other OS and browsers some menu names may differ.
2.3. Minimum System Requirements
Please make sure your PC meets the following minimum requirements:
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
9
NOTE:
The default IP address is 192.168.0.99, default HTTP-port is – 80. You don’t need to enter the port
number if you connect via the default HTTP port.
NOTE:
There are 2 ways to obtain the IP address for the device: 1)Obtain the address automatically from the
DHCP server according to your LAN setup. 2) Use the user-defined IP address. See 8.2 of this manual to
learn more about the available network options. Please consult your system administration before using
the device..
Chapter 3. Getting Started
3.1. Installation of ActiveX components and Authorization
Step 1: Connect the door station following the Installation User Manul.
Step 2: Run Internet Explorer and enter the following path in the address :
http://<IP>:<PORT>, where <IP> is the IP address of the door station, <PORT> is number of the port
used for HTTP connection to the device.
Pic. 3.1
If the path is correct, the authorization window will open.
Step 3: To work with the web interface you need to install the ActiveX add-on. You will see the
following system notification at the bottom of the window: “This webpage wants to run the following
add-on: “AxMediaControl ActiveX Control Module” from “BEWARD Co., Ltd”
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
10
ATTENTION!
Installation of ActiveX components is only possible for 32-bit Internet Explorer..
Click [Allow] to start installation.
Step 4: By default, the Internet Explorer security system will block the ActiveX installation.
Click [Install] to continue (Pic. 3.3).
Pic. 3.2
Pic. 3.3
Step 5: Close Internet Explorer and click [OK] in the Warning window (see Pic 3.4) if it pops
up.
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
11
NOTE:
Names of menus and option may differ when using different OS and internet browsers.
NOTE:
In Windows 7 with enabled user account control you an additional installation blocking window may
appear. Give a positive answer permit installation
Attention!
After authorization you can change login and password in Config – System – Access Policy. If you lose
your login and password, you can reset the door station to default settings. To do so you need to press
and hold the reset button 3 times for 10 seconds with 1 second pauses between each press
Pic. 3.4
Step 6: Click [Install] (see Pic. 3.5).
Pic. 3.5
Step 7: After completing the installation you will see the following «Register OCX
success(С:\)» Click [Close] (see Pic. 3.6).
Step 8: Run Internet Explorer and enter the IP address of the door station in the path field. .
Step 9: Enter username and password and click [Login]. Default username – admin, default
Pic. 3.6
password – admin (Pic. 3.7).
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
12
Pic. 3.7
If successful, you will start receiving the videostream from the door station camera (Pic. 3.8).
Pic. 3.8
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
13
The interface window has 5 following: [Live View], [Replay], [Config], [Alarm], [Log Out],
Each tab is explained in this Manual.
If you failed to install ActiveX correctly you can do it again by clicking the link in the
authorization window (see pic.3.9) and following the instructions above
Pic. 3.9
3.2. Main Window (Live View)
The following functions are available in the [Live View] tab: Choose Main/Sub video stream.,
Snapshot. Video recording, “Talk” and “Listen” modes, Zoom, Full Screen mode, “Width:Height”
mode, Original resolution and Image settings.
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
14
Pic. 3.11
Main Stream / Sub Stream: Display the main or the sub stream in the Live View window. The
main stream is displayed at a higher resolution compared to the sub stream. The stream parameters
can be adjusted in Config – Video Settings – Video coding(see paragraph 7.2).
Snap: Press this button to make an instant snapshot of the camera display.Snapshots are
stored in the local folder specified by the user (see paragraph 5) as JPEG files.
Rec: Press this button to start recoding the livestream. The recorded footage will be saved in
the in the local folder specified by the user (see paragraph 5) ).as H.264 video files
Talk: Press this button to activate the two-way audio mode. When activated, sound transmits
from the door station to the PC and vice-versa.
Listen: Press this button to listen to the sound from the door station microphone via PC
speakers
Zoom: Press this button to enlardge a specific area of the video. Press [Zoom], then press
and hold the left mouse button to frame the area. The enlarged area of the video will appear in a new
window. Close the “Zoom In” window and press the [Zoom] button to disable this function.
Full: Press this button to enter Full Screen mode. Press the [ESC] key or click the right mouse
button to turn off Full Screen mode.
W:H: Press this button to apply the correct width to height ratio to the livestream display.
Original: Press this button to display the livestream at the original resolution. If the image is
too big to fit the screen, you can use the scrollbars to navigate.
Chapter 3: Getting Started
IP Video Door Station DS06M(P) Operation User Manual
15
Image: Use this toolbar to adjust the following parameters: «Brightness», «Contrast», «Hue»,
«Saturation». If you want to restore to the default parameters, click [Default] (Pic. 3.12).
Pic 3.12
Chapter 4.Replay
IP Video Door Station DS06M(P) Operation User Manual
16
Chapter 4. Replay
Press «Replay», to open the web interface player tab where you can open videos and images
that are stored in the memory card or your PC (Pic. 4.1).
Size: Change the width to heigh ratio. Available options: Full (screen), 4:3, 16:9, 11:9.
Storage: choose the location of the files you saved. Available options : «PC» and «Memory
Card» :
PC: Search for files in a PC folder. The default path is «C:\MyIPCam\».
Memory Card: Search for files in your SD card.
Type: Choose the file Type. Available types: «All Rec», «Alarm Rec», «Schedule Rec» and
«Images».
Date: choose the date for searching files.
[Search]: Press this button to start searching files.
File list: The search results are listed here in chronological order
[Play]: Select a file in the File List and press this button to play it.
You can use the following toolbar (see Pic. 4.2).
Pic. 4.1
Pic. 4.2
Chapter 4.Replay
IP Video Door Station DS06M(P) Operation User Manual
17
NOTE:
All footage from the time period you set will be saved as one file.
Make sure that you have the rights to create new objects in the storage catalog you chose. In Windows 7
you may need to run Internet Explorer as administrator to allow saving files on the local disk
Note!
In Windows 7 (and later OS version) you may have to run Internet Explorer as administrator to ensure that
the web interface player is working properly.
[Save]: Press this button to save the files from the SD card on your PC. Select a file in the File
List and press [Save]. A new window will appear that shows progress (Pic. 4.3).
Pic. 4.3
IPCam: Door Station ID and its IP address.
Chn: Channel #, choose “1” for the door station
Time: Set the date and the time period you want to save.
[>>]: Choose the path to save files.
[Start]: Start saving files.
[Stop]: Stop saving files.
Chapter 5. Config: Local Config
IP Video Door Station DS06M(P) Operation User Manual
18
NOTE:
Make sure that you the rights to create new objects in the archive folder. Otherwise you will be unable to
save files.
In Windows 7 you need to run Internet Explorer as administrator to save files in the local disk.
Chapter 5. Config: Local Config
Go to the “Config” tab to work with settings menu of the device
The following picture shows the Local Config menu:
Pic. 5.1
View Mode:– «Real Time and «Fluency» modes are available.
«Real Time» mode does not use the buffering procedure and the videostream is displayed
without delay in the «Live View» tab. Any delays and visual defects might be cause by the high load
on your LAN.
«Fluency» mode uses the buffering procedure and the videostream is displayed with slight
delay (less than 1 second) in the «Live View» tab. Use this mode in case of delay of visual defects.
Enhanced Quality: Enabling this option improves the video quality but also increases the
CPU load.
Record Duration: Set the duration of recorded files (in minutes).
Archive Folder Path: Set the local folder to store video and image files. Default Path:
C:\MyIPCam\.
Press [Save] to apply new settings.
Chapter 6. Config: Audio Setting
IP Video Door Station DS06M(P) Operation User Manual
19
ATTENTION!
Adjusting the Input Volume and Output Volume parameters will affect the work of the device and may
cause defects (interrupted speech, echo, etc.)
Adjust these parameters only when it is strongly necessary..
Chapter 6.Config: Audio Settings
The following picture shows the “Audio Parameters” Menu.
Pic. 6.1
Enable the sound: Turn on / off sound transmission. Enabled by default
Audio Input Type: Default option – «Mic». Unavailable to change.
Compression Type: Default – G.711U. Also available: G.711A и G.726.
Bitrate: default – 16000 bps. Unavailable to change.
Sampling Rate: default – 8 kHz. Unavailable to change.
Echo Cancellation: Enable / disable additional echo cancellation. Use this option if the
hardware echo cancellation is insufficient.
Input Volume: set the volume level of the input audio signal. (0~15).
Output Volume: set the volume of the output audio signal (0~15).
Input Volume (Talk): set the volume level of the input audio signal in Talk mode (0~15).
Output Volume (Talk): set the volume of the output audio signal in Talk mode (0~15).
Press [Save].to apply new settings
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
20
Chapter 7. Config: Video Settings
7.1. On-Screen Text
The following picture shows the “On-Screen Text” menu
Pic. 7.1
Title: Enter text (e.g. door station name) that will be displayed at the bottom left corner of the
screen.
Font Color: Choose the text color. Available colors: white, black, yellow, red, blue.
Title: show/hide title.
Date / Time / Day: show/hide date/ time/ weekday.
Date Format: choose date format.
Framerate / Bitrate: show/hide the current framerate and bitrate on the screen
Connections Number: show/hide the number of current connections to the door station web
interface (displayed in parenthesis after the title).
You can also change positions of the text elements. To do so use . (top row for title,
bottom row for everything else).
Press [Save].to apply new changes
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
21
NOTE:
You can change quality only if the «Advanced» option is disabled.
7.2. Video Coding
The “Video Coding” menu is shown in Pic. 7.2.
This menu contains settings for the Main and Sub streams. The main stream provides the
higher resolution and video quality compared to the sub stream. Thus, you can record high quality
video via the main stream while watching the sub stream in real time, even in case of low network
capacity.
Pic. 7.2
Profile: Baseline and Main profile are available.
Encoder mode: H.264 and MJPEG formats are available.
Resolution: set the stream resolution
Main stream: 1280х960, 1280х720;
Sub stream: 720х576, 640x480, 320х240.
Quality: “Basic”/”Normal”/”Fine”.
Advanced: Enabling this option grants access to the following parameters. :
Rate control: Choose the type of bitrate control:
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
22
CBR: Constant bitrate is prioritized while the image quality may change over time. The
current bitrate value approaches the bitrate value you specify in the “Bitrate” field. You can
also specify permitted deviation in the “Bitrate fluctuation” field.
VBR: Image quality is prioritized, while the bitrate may vary, according to different conditions in
the surveillance area. The average bitrate value will approach the value you specify in the “Bitrate”
field but the current value may vary significantly
Bitrate flunctuation: «Self-adaption» means that the bitrate value will be controlled by
software. By selecting «±10%» ~ «±50%» the bitrate will change according to surveillance conditions
within the permitted deviation
Bitrate: set the data transmission speed (available range: 30 ~ 16384 kbit/s). Higher bitrate
value results in higher image quality as well higher resource requirements
Frame rate: Set the framerate. it is not recommended to set to high value at low network
bitrate, which would result in choppy video.
I frame: Set the interval of I-frames. Available range: 1-200. Lower value results in higher
bitrate and higher image quality. It is recommended to set to the same value as the framerate.
[LAN], [WAN]: Templates of coding settings – allow to set the recommended value for LAN
and WAN connections with one click.
[LAN]:
Main stream: «I-frame» – 50, «Frame rate» – 25 fps, «Rate control» – VBR, «Bitrate» –
4096 kbit/s
Sub stream: «I-frame» – 50, «Frame rate» – 25 fps, «Rate control» – VBR, «Bitrate» – 512
kbit/s
[WAN]: «I-frame» – 25, «Frame» – 5 fps, «Rate control» – VBR, «Bitrate» – 384 kbit/s.
Press [Save] to apply new settings.
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
23
7.3. Privacy Mask
The Privacy Mask menu is shown in Pic. 7.3.
Pic. 7.3
Enable Mask: Enable\Disable privacy mask.
[Set the mask]: Click this button and then press and hold the left mouse button selecting the
necessary area. Up to 4 mask areas can be set up.
[Full screen]: Click to mask the whole screen.
[Clear]: Remove all mask area.
Press [Save] to apply new settings.
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
24
7.4. Video Parameters
The “Video Parameters” menu is shown on Pic. 7.4.
Pic. 7.4
Image Parameters: Set such parameters as brightness, contrast, hue, saturation, accuracy
and gamma (available value range: 0~255). Moving the sliders will change the image immediately. To
reset parameters to default, click their corresponding icons)
White Balance: Set automatically by default, but manual adjustment via the red, green and
blue sliders is also available..
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
25
NOTE:
3DNR only works in «Night» mode.
Color/BW: Set a color mode or a black and white mode for the door station camera. The
modes switch automatically by default.
Other: contains the following parameters:
Mirror: Reflect the image.
Flip: Flip the image.
60HZ: Use this mode if the light source equipment in the surveillance area connect to the
60Hz electrical grid. The exposure time is automatically set to the value divisible by 30
50HZ: Use this mode if the light source equipment in the surveillance area connect to the
60Hz electrical grid. The exposure time is automatically set to the value divisible by 25.
In Door / Out Door: Reduce or remove the flickering of indoor or outdoor light sources by
means of the pulse-width modulation.
DWDR: Enable Digital Wide Dynamic Range mode. The available options are
«Low»/«Normal»/«High».
Smart NR: This option increases 3DNR efficiency in low light conditions and reduces the
blurry effect of moving objects.
2DNR: Reduce noise in low light conditions. The available image processing options:
«Low»/«Normal»/«High».
3DNR: Reduce noise in low light conditions. This option does not affect the image detail, but
there may be traces of moving objects depending on value you set with the slider.
Anti-Fog: Show better details in case of fog.
Color Correction: Enabling this function allows for better rendition of colors by correction of
hues.
Anti-Tremble: Reduce tremble if the device is exposed to vibrations.
Maximum Exposure Time: Set maximum exposure time value. Available values:
«1/25»~«1/8000».
Auto Gain Control: Automatically increase brightness in low light conditions. Bigger AGC
values result in higher noise levels
Day/Night Mode: Activate «Day» and «Night» presets:
Schedule: «Day» and «Night» modes will switch as scheduled. When selected, you will
be able to set the schedule time in additional fields.
Light Sensor: «Day» and «Night» modes will switch via the built-in light sensor. Set the
operation mode in the drop-down list below. “Day – Night”- Day mode in high external
Chapter 7.Config.Video Settings
IP Video Door Station DS06M(P) Operation User Manual
26
light levels, Night mode in low external light levels. “Night – Day” - Night mode in high
external light levels, Day mode in low external light levels
IR Cut Filter/IR Light Modes: Set the operation modes for IR filter and IR LED
ICR: Blocks infrared wavelengths for better rendition of colors.
o «On at night»: Blocks IR spectrum during the Day Mode, transmits IR spectrum during
the Night Mode
o «On in a daytime»: Transmits IR spectrum during the Day Mode, blocks IR spectrum
during the Night Mode
IR Light: Use IR LED in low external light level conditions.
o «On in a daytime»: Day mode: LED is disabled, Night Mode: LED is enabled
o «On at night»: Day mode: LED is enabled, Night Mode: LED is disabled
o «Disabled»: LED is always disabled.
IR optimizer: Allows for facial recognition at nighttime by making sure that there is no
excessive IR LED light at the center of the image.
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
27
ATTENTION!
Your router must support map mapping in order for this function to work.
Chapter 8. Config. Network Settings
8.1. Basic
The “Basic Settings” menu is shown below.
Pic. 8.1
Data Port: Port used for video data transmission. Default value – 5000. Recommended values
– 1124-7999 (This field is not recommended to change without necessity).
HTTP Port: Port used for a web browser. Default value – 80. Recommended values – 80 и
1124-7999 (This field is not recommended to change without necessity).
ONVIF port: Port used for ONVIF protocol. Default value – 2000. Recommended values –
1124-7999 (This field is not recommended to change without necessity).
Enable port mapping – The door station connects to the router and automatically forwards its
ports behind NAT. If successful, the external ports and the IP address will be shown in fields below.
Upnp server – IP address of the server that will automatically forward ports behind NAT
Address
Press [Save] to save new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
28
NOTE:
IP addresses in the network must be unique when assigning an IP address to the door station. Applying
new settings in the “LAN” menu requires a reboot.
ATTENTION!
After changing the network settings the IP door station will automatically reboot .
8.2. LAN
The “LAN” settings menu is shown below.
Enable IPv6: Allows 128-bit IP addresses for door station connections.
DHCP: Automatically receive main network parameters from a DHCP server (The server must
be set up in local network).
IP Version (available if IPv6 is enabled): Select «IPV6», to use 128-bit IP addresses
IP address: Enter IP address if DHCP is disabled.
Subnet mask: Default value is 255.255.255.0 (This field is not recommended to change).
Gateway: set the gateway address.
Main DNS: set the preferable DNS address.
Sub DNS: set the alternative DNS address.
MAC: MAC address of the door station (This field is not recommended to change).
Pic. 8.2
Press [Save].to apply new settings
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
29
8.3. PPPoE
The “PPPoE” settings menu is shown below.
This menu allows setting up the PPPoE network that can be used to connect the door station
to the Internet after obtaining the dynamic IP address, username and password from your Internet
Provider.
Pic. 8.3
Enable: Enable/disable PPPoE.
Authentication Type: choose the authentication protocol.
IP address: IP address or domain name of the PPPoE server (given by the server)
Username: enter your username for the PPPoE connection.
Password: enter your password for the PPPoE connection.
Online Time: Duration of connection.
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
30
8.4 UPnP
The “UPnP” settings menu is shown below
Enable UPnP: enable\disable network detection via UPnP
Device name: Name that will be displayed in UPnP search results.
Press [Save] to apply new settings.
Pic. 8.4
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
31
8.5. E-mail
The “E-mail” settings menu is shown below
Pic. 8.5
This menu contains parameters of the e-mail client used to send image snapshots via e-mail.
SMTP server: Enter the IP address or the name of the SMTP server in use.
From: enter the sender’s e-mail address
To: enter the receiver’s e-mail address. Mail messages will be sent to this address.
SMTP Username: enter your username to access the SMTP server.
SMTP Password enter your password to access the SMTP server.
SMTP port: enter the port number of the SMTP server (default value – 25).
SSL: enable if your Internet provider requires SSL.
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
32
NOTE:
Make sure you have enough rights to save files to the FTP server in use
8.6. FTP
The “FTP” settings menu is shown below:
Pic. 8.6
This menu contains parameters of the FTP client used for sending video footage and
snapshots to the FTP server. You can set up 2 servers. If the main server is not available, the sub
server can be used instead
Address: IP address of the FTP server.
Port: port of the FTP server. Default value: 21.
FTP Catalog: Set the folder for recorded files on the FTP server. If the folder does not exist, it
will be created automatically in the root server folder.
Username / Password: enter your username and password to access the FTP server.
Port from /to: Range of ports to access the FTP server.
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
33
8.7. DDNS
The “DDNS” settings menu is shown below:
Pic. 8.7
This menu contains parameters for setting the connection via DDNS service. DDNS allows
you access the door station from the Internet even if you only have a dynamic IP address.
Every time your current IP address is changed, it is automatically compared with the specific
domain name used to access the door station from the Internet at any moment.
Enable: enable/disable DDNS.
DDNS server: select DDNS provider from the list.
Username: enter the username obtained from the DDNS provider website after registration.
Password: enter the password obtained from the DDNS provider website after registration.
Domain: enter the domain name obtained after registration.
Server URL: enter the URL address of the DDNS provider.
Server Port: enter the port used for DDNS. Default value: 30000 (This field is not
recommended to change).
Data port: enter the data port used for port mapping.
HTTP port: enter the HTTP port used for port mapping.
Update Interval: set the interval at which the device will update IP address on the DDNS
server after IP address change.
External IP: external IP address of the door station defined by your Internet provider.
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
34
8.8. PPTP
The “PPTP” settings menu is shown below:
Pic. 8.8
Enable: enable/disable PPTP.
Server URL: enter the IP address or the domain name of the PPTP server.
Username: enter your username to access the PPTP server..
Password: enter your password to access the PPTP server.
IP address: IP address obtained after connecting to the PPTP server
Online Time: PPTP connection status.
Press [Save] to apply new settings.
8.9. RTSP
If RTSP is enabled you will be able to watch the video stream from the door station in real time
via third-party players that support standard RTSP protocol (VLC, Quick Time, Real Player etc.).
Enter the following request to access the video stream via third party RTSP clients
rtsp://<IP>:<PORT>/av<X>_<Y>
<IP> – IP address of the device;
<PORT> – RTSP port of the device (default value – 554.);
<X> – command of the video stream channel. The channels begin with 0. Since the door
station has a single channel, enter “0”
<Y> – command of the video stream profile: 0 – main stream, 1 – sub stream.
Request example: rtsp://192.168.0.99:554/av0_0.
The coding type for the video stream is specified in the coding settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
35
NOTE:
When you connect to the device from the Internet the bitrate depends on the access channel obtained
from the ISP.
ATTENTION!
RTP multicast should be supported by your router.
The “RTSP” settings menu is shown below:
Pic. 8.9
Enable: enable\disable RTPS.
Enable Authentication: Turn on the authorization procedure when getting access to the
RTSP stream. The following request must be used to gain access:
rtsp://<IP>:<PORT>/av<X>_<Y>&user=<USER>&password=<PASS>, whee <USER> – username,
<PASS> – password.
Request example: rtsp://192.168.0.99:554/av0_0&user=<admin>&password=<admin>.
Port: RTSP port. Default vale: 554.
Packet Size: set the size of the data packet. Default value: 1460.
RTP multicast: broadcast settings for audio and video streams in multicast networks
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
36
8.10. HTTPS
The “HTTPS” settings menu is shown below:
Pic. 8.10
Before using HTTPS connection you need to set parameters in the web interface client.
You can create a self-signed certificate or make a request to the Certification authority to
create the certificate
[Create Self-Signed Certificate]: Click to create a new self-signed certificate. Fill in the fields
in the pop-up window and click [Submit]. The created certificate will be shown in the “Installed
Certificate” field.
[Create Certificate Request]: Click to make a request to the Certification authority . . Fill in
the fields in the pop-up window and click [Submit]. The created request will be shown in the “Created
request” field.
Created request: request to the Certification authority.
[Properties]: Examine the information on the certificate request that will be sent to the
Certification authority.
[Remove]: remove the certificate request.
[Install Signed Certificate]: Install the certificate you received from the Certification authority
in response to your prior request. Pressing this button will open a new window where you can upload
your certificate. Choose the certificate file (“.pem”) and click [Upload]. The certificate must match the
request because the data are compared during installing.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
37
NOTE:
Change Internet Explorer security settings to be able to upload files from local folders. Go to Tools –
Internet options – Security and click [Custom level]. Find «Include local directory path when
uploading files to a server» and select «Enable» (Pic. 13.5).
Installed Certificate: name and state of the installed certificate.
[Properties]: examine the properties of the current certificate
[Remove]: remove current certificate.
HTTPS Connection Policy: select protocol in use. Available protocols: HTTP, HTTPS, HTTP
& HTTPS.
If you are using port forwarding on your router, please note TCP Port 443 is used for the
HTTPS protocol.
Press [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
38
8.11. SIP
The “SIP” settings menu is shown below:
Before using SIP connection you need to set parameters in the web interface client.
Enable SIP #1 (#2): Activate SIP account. Only a one account can be active at one time. Both
accounts are disabled by default.
Registration status: Account status in the SIP server.
Name: Name of the door station. Displayed during calls. This field is empty by default.
Number: Number of the door station used for calls by other subscribers. This field is empty by
default.
Username/Password: used to register the door station in the SIP server. This field is empty
by default
SIP port: Number of the port used for interactions with a SIP user agent. Default number -
5060.
Pic. 8.11
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
39
ATTENTION!
STUN does not work properly with symmetric NAT. When using symmetric NAT the IP address of the
STUN server will differ from the endpoint address. Therefore the NAT address seen by the STUN server
will also differ from the endpoint address used for sending data to the user agent..
Allow registration: Allow the door station to be registered in the SIP server. Disabled by
default.
Get the address of a registration server via DHCP: Check to enable this option. SIP server
must support this function.
Registration server/Port: The network address and port of the registration server. The
network address may match the SIP server address. These fields are empty by default.
Get the address of a proxy server via DHCP: Check to enable this option. SIP server must
support this function.
Proxy Server/Port: network address and port of the Proxy server.
SIP Server/Port: network address (for telephone exchange) and port (for data exchange) of
the SIP server. These fields are empty by default.
NAT: the door station operates via a STUN server. STUN server is one of the secure ways of
getting access to devices within the network that are behind NAT. Disabled by default.
STUN IP/STUN port: network address and port of the STUN server.
DTMF Mode: select DTMF signal transmission mode. Available modes:
RFC2833 – send DTMF tones within RTP packages.
In-Band – DTMF signals are found in the media stream; G.711 alaw/ulaw only.
SIP INFO – send DTMF tones within INFO-messages.
Stream Type: Select the type of stream transmitting during SIP sessions between the Guest
and the Client. Applied for both accounts. The main stream is selected by default. “Audio only” is also
available.
Call subscriber when pressing “Call” button: Call recipient by pression the “Call” button on
the door station panel. This function is disabled if no Call recipient is selected.
Call account: call recipient(s) by pressing the “Call” button. «SIP 1» is selected by default. If
SIP 1 is not available, the value switches to «SIP 2» (and vice versa).
Call Recipient 1-5: Select the recipients that must be called when the “Call” on the door
station is pressed. These fields are empty by default.
Relay Out 1-3 (DTMF): set the value of the DTMF signal. The relay outputs will close when
the signal is received. For example, the door will open when the specified phone button is pressed.
Up to 3 DTMF symbols are available (0-9, #, *). These fields are empty by default.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
40
End SIP session after door opening: when the “open the door” command is received (the
door station receives the DTMF signal to close the relay outputs) the current SIP session ends. This
function can be set up for each relay output separately. This function is disabled by default.
Call timeout: the amount of time during which the door station will call the subscriber.
Available values: 10~300 s.
Receive incoming calls: Automatically receive incoming calls using the SIP account(s). If the
receiving account is not available the door station cancels the call and send the cancel message to
the caller.
Use call melody: use standard call melody instead of the phone ringing sounds when calling
recipient via SIP.
Number of repeats: set how many times the call melody should be repeated. If the value is
set to «0» the ringtone melody will play an infinite amount of times.
Answer without sound: when enabled the call recipient will see and hear the guest but the
guest will not be able to hear the recipient or be aware that the connection has been established.
Enable sound with command (DTMF): set the value of the DTMF command (available
symbols: 0-9, #, *) used to enable sound transmission from the recipient to the guest.
Stop calling on beginning the talk via SW: Automatically end calls, if the recipient answered
with the use of Beward software or compatible applications.
End SIP session by pressing “Call” button: Enables the subscriber on the door station side
to end the SIP session by pressing the “Call” button. This option can be used during the call or
during the talk. Both options are enabled by default.
Click [Save] to apply new settings.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
41
8.12. Modbus
The “Modbus” settings menu is shown below:
Use the Modbus protocol to connect to compatible equipment.
Enable: enable\disable Modbus.
TCP port: number of the port for the Modbus protocol. Default number – 502.
Click [Save] to apply new settings.
Pic. 8.12
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
42
NOTE:
Internet connection is required to use CamDrive. The output bitrate must be 512 kbps or higher.
8.13. CamDrive
Connect the door station to the CamDrive video surveillance service to record video data
watch the archive only from any place with Internet access, without using a static Ip address.
The “CamDrive” settings menu is shown below:
Pic. 8.13
Enable: press the checkbox click [Save] to connect to the CamDrive service. The door station
will restart and all fields in this menu will be filled in (Pic. 8.14).
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
43
ATTENTION!
1. The CamDrive service can be enabled only if an SD card is installed. Please note that SD card will be
formatted and all existing data will be erased.
2. Enabling this service will cause the following functions to become unavailable.(Their settings will reset):
PPPoE, E-mail, FTP, PPTP, RTSP, Memory Card (recording/writing).
3. You will be unable to access control and talk modes when the door station is connected to the
CamDrive service.
ATTENTION!
Disconnecting from the service will erase files stored in the SD card in CamDrive mode.
Pic. 8.14
Account Registration Data: www.camdrive.com: click this link ad enter login and password
to create a new CamDrive account or connect the door station to the one already existing.
Activation login: admin: login to enter the account.
Activation password: password to enter the accoutn.
IP address: IP address assigned by CamDrive to the door station.
MАС-address: MАС address assigned by CamDrive to the door station.
Connection time: Time passed since the door station connected to the CamDrive service.
Uncheck the “Enable” box and click [Save] to disconnect from CamDrive. The device will
restart and all unavailable function will become available again.
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
44
8.14. HTTP Event
This function sends commands from the door station to other network devices when motion
detection is activated or when the call button is pressed.
The “HTTP event” settings menu is shown below:
Pic. 8.15
Enable: turn on HTTP event function.
Protocol: select the preferred protocol to send notifications (commands). Available protocols:
HTTP, HTTPS.
Hostname: address and command for your HTTP event server. «&» и «=» are unsupported.
For example, For URL «http://www.eventserver.org» enter «www.eventserver.org» in the
“Hostname” field.
You can also enter a port number, which will differ from the default one (e.g. enter
«www.eventserver.org:81». if the port number is 81).
Default port numbers («80» for HTTP and «443» for HTTPS) are set automatically when you
select the protocol.
Request: enter a request for your HTTP event server. For example, enter “/alarm” for theURL
«http://www.eventserver.org/alarm» .
Method: method of sending notifications: GET or POST.
Authorization: enable authorization for sending notifications
Username: enter username for authentication. Maximum length is 20 symbols, including
upper case letters and the following symbols: «!», «@», «#», «$», «*», «_», «-», «,», «.».
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
45
Password: enter password for authentication. Maximum length is 20 symbols, including upper
case letters and the following symbols: «~», «!», «@», «#», «$», «%», «^», «*», «(», «)», «_», «+»,
«{», «}», «:», «"», «|», «<», «>», «?», «-», «;», «'», «\», «,», «.», «/».
Additional parameter: name of the additionally sent parameter. It is commonly required for
the server when using a POST request
Additional value: enter value of the additional parameter if necessary
Additional body: additional information added to the body of the notification. It can be used
for adding program code to send messages in online chats, blogs etc.
[Test]: Click to check if the data you entered is correct. The HTTP request will be sent to the
specified address.
Click [Save] to apply new settings
HTTP event examples
1) When motion detection is activated (see paragraph 10.1):
Pic. 8.16
Chapter 8. Config. Network Settings
IP Video Door Station DS06M(P) Operation User Manual
46
2) When the “Call” button is pressed (see paragraph 10.2):
Pic. 8.17
In both cases you must check the “HTTP event” box and enter the required parameter.
Maximum length requests is 127 symbols. «&» and «=» symbols are supported.
This parameter will be sent to the HTTP event server you entered in the settings menu (see
pic. 8.15) in accordance with GET/POST methods.
Notifications will not be sent if the HTTP event server is not set or disabled
A HTTP request with additional parameters is made as follows:
http://<”Hostname”>?< ”Additional parameter” >=< ”Additional value” >&<”HTTP
event”>HTTP/1.0
A HTTP request without additional parameters is made as follows:
http://<”Hostname”>?<”HTTP event”>HTTP/1.0
Chapter 9. Config: Record Settings
IP Video Door Station DS06M(P) Operation User Manual
47
ATTENTION!
The hot swap of a memory card is not supported by the door station and may damage the device or cause
data loss!
Do not turn off the door station when formatting the memory card.
The device does not support memory cards with several partitions after formatting.
ATTENTION!
The overwrite function is enabled by default. If the memory card is full. old files are automatically deleted
to make space for new files
Chapter 9. Config: Record Settings
9.1. Memory Card
The “Memory Card” settings menu is shown below:
This page contains information on the status of the memory card (installed/ not installed), its
total capacity and free space:
[Format]: start formatting the memory card.
[Refresh]: refresh information about the current parameters of the memory card.
Pic. 9.1
Chapter 9. Config: Record Settings
IP Video Door Station DS06M(P) Operation User Manual
48
NOTE:
If «FTP» disabled, video files will be stored in the memory card .
ATTENTION!
The memory card installed by default also used for caching files when recording them to the FTP server.
The duration of video clips does not depend on the size of the inner buffer of the door station.
If the memory card is not installed, the inner buffer (~1MB) will be used for caching files. The duration of
video clips will vary from 1 to several seconds, depending on bitrate value
NOTE:
«Stream Type» also applies to video recording on alarm.
9.2. Video Recording
The “Video Recording” settings menu is shown below:
Pic. 9.2
Record on Schedule: Enable scheduled video recording to the FTP server. FTP server
parameters can be set in the «FTP» menu (see paragraph 8.5).
Record Duration: set the duration for video files. Available values: 1~60 min.
Time 1/2: Set schedule for video recording. Two schedules are available.
Stream type: choose between the main or sub streams used for recording.
Press [Save] to apply new settings.
Chapter 9. Config: Record Settings
IP Video Door Station DS06M(P) Operation User Manual
49
NOTE:
If «FTP» and/or «E-mail» options are disabled the snapshots will be stored in the memory card,
If «FTP» and/or «E-mail» options are enabled .the snapshots will be stored in the FTP server and/or sent
via E-mail
ATTENTION!
The memory card installed by default is also used for caching files when recording them to the FTP server
or via E-mail. You can find the files in the memory card as well.
NOTE:
«Resolution» also applies to snapshotting on alarm.
9.3. Snapshotting
The “Snapshotting” settings menu is shown below:
This page contains settings that allow you to set the schedule for the snapshotting function
and set the snapshot folder
Snaps on Schedule: enable scheduled snapshotting. Send snapshots to the FTP or E-mail.
Pic. 9.3
E-mail parameters can be set in the «E-mail» menu (see paragraph 8.4 ), FTP-client parameters can
be set in the «FTP» menu (see paragraph 8.5).
Snap Interval: set the time interval between snapshots. Minimum interval – 1 second,
maximum interval – 3600 seconds.
Time 1/2: set the schedule for snapshotting. Two schedules are available.
Resolution: select resolution for snapshots
Press [Save].to apply new settings
Chapter 10.Config: Alarm Settings.
IP Video Door Station DS06M(P) Operation User Manual
50
Chapter 10. Config: Alarm Settings
10.1. Motion Detection Settings
The “Motion Detection” settings menu is shown below:
Pic. 10.1
Here you can set motion detection parameters and conditions for sending files and
notifications on motion detection triggers
[Set motion area]: set the motion detection area. Click and hold the left mouse button to
frame the desired area. Up to 4 areas can be set up.
[Full screen]: set the whole image as the motion detection area.
[Clear]: clear all motion detection areas.
Sensitivity: set the motion detection trigger sensitivity. 5 levels are available: higher level
leads to higher sensitivity.
Enable: enable/ disable the motion detection function.
Time 1/2: set motion detection operation by schedule. You can set 2 operating time periods.
HTTP event: enable and set the necessary parameter in the text field. The parameters will be
sent to the HTTP server (see Config – Network settings – HTTP event) when the motion detection
trigger activates.
Maximum length – 127 symbols. «&» and «=» symbols are not supported.
If the HTTP/HTTPS event server is not set or enabled, notifications will not be (See paragraph
8.13 for further details).
E-mail notification: enable/disable e-mail notifications for motion detection triggers.
Snapshot: activate snapshotting for motion detection triggers. Specify the amount of snaps in
the field to the right.
Snap interval: set the time interval between snapshots.
Chapter 10.Config: Alarm Settings.
IP Video Door Station DS06M(P) Operation User Manual
51
ATTENTION!
The default memory card is also used for caching files when sending them to FTP server or E-Mail, so you
can find the files on the memory card
ATTENTION!
The default memory card is also used for caching files when sending them to FTP server. The duration of
video files is not limited by the size of the inner buffer of the door station
If there is no memory card installed, the inner buffer (~1mb) of the door station will be used instead. The
duration of video files will vary from 1 to several seconds, depending on the bitrate value
E-mail / FTP: set E-mail and/or FTP server as destinations for snapshots. If neither is
selected, the snapshots will be sent to the memory card.
Record: enable/ disable video recording for motion detection triggers.
Record time: set the duration for video files.
FTP: set the FTP server as a destination for recorded video files. If disabled, the memory card
will be used instead.
Press [Save].to apply new settings
Chapter 10.Config: Alarm Settings.
IP Video Door Station DS06M(P) Operation User Manual
52
ATTENTION!
The default memory card is also used for caching files when sending them to FTP server or E-Mail, so you
can find the files on the memory card
10.2. Call Button
The “Call Button” settings menu is shown below:
Pic. 10.2
This option is always enabled by default, so the “Enable” and “Time 1/2” checkboxes are not
available.
HTTP event: if enabled, pressing the call button of the door station will trigger the sending of
parameters to the HTTP/HTTPS server (see paragraph 8.13 for further details).
E-mail notification: send an e-mail notification when the call button is pressed.
Snapshot: make snapshots when the call button is pressed. You can set the amount of
snapshots in the field to the right
Snap interval: set the time interval between snapshots.
E-mail / FTP: set E-mail and/or FTP server as destinations for snapshots. If neither is
selected, the snapshots will be sent to the memory card.
Record: enable/ disable video recording when the call button is pressed.
Record time: set the duration for video files.
FTP: set the FTP server as a destination for recorded video files. If disabled, the memory card
will be used instead.
Chapter 10.Config: Alarm Settings.
IP Video Door Station DS06M(P) Operation User Manual
53
ATTENTION!
The default memory card is also used for caching files when sending them to FTP server. The duration of
video files is not limited by the size of the inner buffer of the door station
If there is no memory card installed, the inner buffer (~1mb) of the door station will be used instead. The
duration of video files will vary from 1 to several seconds, depending on the bitrate value
NOTE:
In case of connection loss snapshots and video files can only be recorded if the memory card is installed!
Press [Save].to apply new settings
10.3. Connection Loss
The “Connection Loss” settings menu is shown below:
Here you can set different actions which can be performed in case of connection loss.
Enable: enable/ disable recording of snapshots and videos in case of connection loss.
E-mail notification: enable E-mail notifications on connection loss. Notifications are sent right
after the connection issues are solved.
Snapshot: make snapshots in case of connection loss. Set the amount of snapshots in the
field to the right
Snapshot interval: set the time interval between snapshots.
Record: activate video recording in case of connection loss.
Record time: set the duration for recorded video files.
Press [Save].to apply new settings.
Pic. 10.3
Chapter 11.Config:Controller
IP Video Door Station DS06M(P) Operation User Manual
54
Chapter 11. Config: Controller
The “Controller” settings menu is shown below:
Pic. 11.1
The package contents may include a 1-channel (NC103 / NC103P) or a 3-channel controller
(NC311P), depending on the purchased model of the door station.
Various types of devices can be connected to the door station. These may include: doors/door
locks, garage openers, light switches, alarm systems etc. 1-channel controllers support one device,
while 3-channel devices support up to 3 devices.
3-channel controllers allow operating 3 different door locks via a single door station. For
example, you can open the gates, the garage door and the front door.
Controller type: choose between «1 channel» and «NC311P». selecting «NC311P» will
enable the additional «Controller connection» option. (see below).
Duration: set the duration for the closed/open status of controller outputs (depending on the
type of the lock and its controller).
For the NC311P controller type, if the duration value is “0”, the controller outputs stay open
until receiving a closing command from the user. If the duration value is in the range from 0.1 to 3600
seconds, the controller outputs will open and close in specified time.
Close on call: set closing relay output contacts when the call button is pressed if necessary
(for example, when connection a door bell).
Facial recognition: this option appears when the “Facial recognition” function is enabled (see
chapter 12). The door opens if a face is successfully recognized.
Night Mode IR LED: IR LED has 2 operating modes – «Always enabled» and «On request».
The «On request» mode is active by default.
Chapter 11.Config:Controller
IP Video Door Station DS06M(P) Operation User Manual
55
NOTE:
The “Door Opening Sound” function does not work together with the “Close on call” option for the selected
relay output.
The “Door Opening Sound” function does not work when opening the door via the SIP connection (sound
cannot be played when the SIP channel is open)
ATTENTION!
Using the “On Request” mode and the motion detection function simultaneously at nighttime leads to
malfunctions and must be avoided.
ATTENTION!
When connecting the NC311P controller (included in DS06MP-3L package contents) for the first time (or
when replacing it with another NC311P controller), it is obligatory to set interaction between the controller
and the door station. Otherwise you will not be able to operate the controller.
In the «On request» mode IR LED activates when the call button is pressed or when receiving
the video stream via program client (PC applications or web browser)
In the «Always enabled» mode the door station automatically switches between Day/Night
modes on sensor without additional external actions.
The «On request» mode is preferable: it increases LED operating time and hides the door
station from prying eyes during nighttime.
Door Opening Sound: the door station speaker plays sound signals when opening the door
via BEWARD Intercom and Beward IP Visor software.
Controller connection: (NC311P controller type only) press the [Connect] button to set
interactions between the controller and the door station.
Press the “LINK” button on the controller (refer to the Installation Manual for details) and
press the [Connect] button. The interaction process will takes about 1 minute. Do not turn off or
restart the door station during the interaction process.
Press [Save].to apply new settings
Chapter 12.Config: Facial Recognition
IP Video Door Station DS06M(P) Operation User Manual
56
NOTE:
Facial recognition is only available for DS06M, DS06M and DS06MP (firmware version - 3.1.0.0.6.18)
ATTENTION!
The facial recognition algorithm works when a face is 0.5 meter away from the door station or closer.
NOTE:
As an infrared filter is used to improve facial recognition results at any time of the day or night, a
video image from the door station becomes black and white in short periods
The amount of simultaneous connections (users) to the door station affects the face recognition
time. Having more than 4 simultaneous connections is not recommended.
Chapter 12. Config: Facial Recognition
Facial recognition is a function of automatic access control which allows, without using any
additional equipment, a specified group of visitors to enter a building. The function can operate
independently, without connecting the door station to the Internet.
By default, the facial recognition is initiated when a visitor pushes and holds (during 1 second)
the call button of the door station. In the process of analyzing visitor’s face the door station emits a
sound during the one a visitor should stand still and look into the lens of the door station camera. In
case of recognition the door station emits a short sound signal and opens the door. In case a visitor is
not added to the face image database or the door station is not recognized him, it emits two short
signals.
Chapter 12.Config: Facial Recognition
IP Video Door Station DS06M(P) Operation User Manual
57
NOTE:
The function is only available on the DS06M door stations with an SD card inserted.
ATTENTION!
Opening the door by facial recognition can’t be used for buildings with an increased security level!
Recognition errors (their frequency depends on the threshold value) and opening the door to unknown
persons is possible
The following conditions may influence the correctness of facial recognition operation):
A back light of the sun or other light sources
Clothes and accessories (such as glasses, kerchiefs, masks etc.) that can conceal the face
partially or completely.
Light-reflecting and light-absorbing paints (make-up) on visitor’s face.
12.1 Settings
Pic. 12.1
Enable Facial recognition – enable the facial recognition function.
Recognition sound indication – enable emitting sound signals (recognized/unrecognized,
face analysis) by the door station.
Door opening threshold – this option allows you to set a specific recognition threshold; when
it is reached the door station opens the door. The bigger a threshold value, the higher a security level,
but then there are also higher requirements to the match of visitor’s face real-time image and the one
from the database. Reducing the threshold value leads to better recognition results but may cause
recognition errors and opening the door to unknown persons.
Chapter 12.Config: Facial Recognition
IP Video Door Station DS06M(P) Operation User Manual
58
NOTE:
Face image database can contain up to 30 images.Up to 5 images per one visitor are available.
12.2 Face Image Database
Pic. 12.2
Face image database contains a list of visitors which are allowed to enter the building,
passing the facial recognition procedure.
Person – a drop-down list of visitors added to the door station database.
After choosing a particular person you can edit his name and face images which are used for
the facial recognition.
Name – visitor’s name and surname.
Edit – this button allows you to change visitor’s name.
Add – click this button to add a new person to the database.
Remove – click this button to remove visitor’s data (including the face images) from the
database.
Learning –activate Learning mode which is used for adding face images for the current
person. When the mode is activated, the door station starts periodically emitting short sound signals.
To allow the camera to capture a face, a visitor should stand before the door station and push the call
button. When a face is captured successfully the door station emits one short sound signal; in case a
face is captured not successfully the door station emits two short sound signals. Duration of the
Learning mode is specified in the Learning time field.
Face images area – face images of the chosen person are situated in this area.
Chapter 12.Config: Facial Recognition
IP Video Door Station DS06M(P) Operation User Manual
59
You can click the image twice to remove it from the database.
Export and Import buttons are used to transfer the database from one door station to another.
Recommendations on filling up the Face image database:
Create and set the database on the door station installed on the wall. Do not change the
position of the door station after the facial recognition function is set!
Stand before the door station in a way you can easily push the call button.
Stand still and look directly into the lens of the door station camera while it captures your face
until you will hear the sound signal.
Make 2-3 images with different positions of the face (see the picture below).
Pic. 12.3
Chapter 12.Config: Facial Recognition
IP Video Door Station DS06M(P) Operation User Manual
60
NOTE:
If some face image is removed from the database, then it is marked as “Removed” in the event
list. If no images are found in the database to be matched with the currently captured face
image, then the visitor is marked as ”Not found”.
12.3 Events
Pic. 12.4
Events – this tab contains a log of facial recognition events when the function is enabled.
The events are situated in the table which is divided to several columns:
Date and Time – date and time of an event.
Name – visitor’s name in the database.
Photo from DB – visitor’s face image from the database used for the matching procedure.
Snapshot – visitor’s face real-time image.
Threshold, % - shows how much the face from the captured image matches the face from the
database,
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
61
Chapter 13. Config: System
13.1. System Info
The “System Information” menu is shown below:
Pic. 13.1
Device Name: change the device name for its easy identification.
Video Standard: choose the standard of video broadcasting (PAL/NTSC).
Language: it is possible to upload different localization files in the “Upgrade” menu (see
paragraph 13.4).
Device ID: unique ID number of the device
Device Model: Model of the device for easy identification when connection to the device
remotely..
Firmware Version: the current installed version of firmware for this device.
Build Date: the date when the firmware was built.
Web UI Version : the current installed version of the web interface.
Press [Save] to apply new settings
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
62
13.2. System Time
The “System Time” settings menu is shown below:
Pic. 13.2
Time Format: choose the time displaying format – 12- or 24-hour.
ONVIF Synchronization Type: choose the type of door station synchronization in accordance
with appropriate time standard (CST/GMT/UTC).
Time Zone: choose the time zone in accordance with location of the door station.
Current Time: these fields contain current date and time entered manually or synchronized
via an NTP server.
NTP Server: tick off this option to obtain time and date from a standard time server (by default
– time.nist.gov) in Internet, using the NTP (Network Time Protocol). You can enter web address and
port of an NTP server in the fields to the right.
Manual/Auto: the two ways an NTP server can be selected.
Set “Manual” to enter address and port of the NTP server in the fields to the right.
Set “Auto” to let the door station try to use NTP servers from the list by default till the moment
of successful synchronization. The fields to the right will not be available. The list of NTP servers by
default is given in the Appendix A.
Synchronize with Local Computer: press this button to set date and time according to time
settings of the PC which is used for work with the web interface of the door station.
Set the Time Manually: choose it to set date and time manually in the “Current Time” field.
DST Type: you can choose the specific date of time advancing (“Date” type) or a day of the
week (“Week” type).
Start / End Time: set the time of advancing and backward adjusting.
DST Bias: set a size of the time shift.
Press the [Save] button to apply new settings.
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
63
NOTE:
When entering the username and password, pay attention to the size of symbols. Both uppercase and
lowercase letters are available. The length of username and password vary from 1 to 15 symbols which
may include Latin letters (A-Z, a-z), figures from 0 to 9 and a dot (.).
13.3. Access Policy
The «Access Policy» settings menu is shown below:
Pic. 13.3
Validation Mode – WEB: this mode determines that username and password for door station
access are entered in the authorization window.
By default the door station has 3 user accounts:
“Administrator” has username and password as “admin / admin”. This is the main user
account so it has no limits of access rights.
“User1” has username and password as “user1 / user1”.
“User2” has username and password as “user2 / user2”.
The following parts of the web interface are only available for the users authorized as “User1”
and “User2”: “Live View”, “Replay” and “Local Config”.
Press the [Save] button to apply new settings.
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
64
NOTE:
It is necessary to change Internet Explorer security settings to permit uploading files from the local folder.
For this purpose, go to the menu Tools – Internet options – Security and press the [Custom level]
button. Find the item “Include local directory path when uploading files to a server” in the opened
window and select “Enable” (Pic. 13.5).
13.4. Upgrade
The “File Uploading” menu is shown below:
Pic. 13.4
To upgrade the device firmware or upload a localization file do the following:
1. Press the [Browse] button. Choose the appropriate file in the opened File Explorer
window and press the [Open] button.
2. Press the [Upload] button to start upgrading. The door station is automatically rebooted
after upgrading procedure completing.
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
65
ATTENTION!
Use only appropriate firmware files which are compatible with the device model! The device may operate
incorrectly and be damaged in case of using an unsuitable firmware file.
Do not disconnect the device from the network while the firmware is upgraded. The door station will have
the IP address 192.168.0.99 after restoring to default settings.
The device breakdown caused by incorrect firmware upgrading is not covered by the warranty
3. Set door station parameters by default (see paragraph 13.5).
Pic. 13.5
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
66
13.5. Restore
The «Restore» settings menu is shown below:
Pic. 13.6
Here you can set the door station by default in case of some problems or after firmware
upgrade. Moreover, you can save the main door station settings as a file to reset them later.
[Export]: click to save door station settings as a file with the “.bak” extension. The file name
contains the date and the time of saving (according to the door station clock).
[Import]: click to reset the settings from the “.bak” file. Click [Browse], choose the file and
click [Import]. After restoring the settings the device will be rebooted.
[Restore]: press this button to set door station parameters by default. Enter the administrator
password and press the [OK] button to confirm restoring in the opened window. Press [Х] to cancel
restoring. Here you can also put a tick “Save network settings” to keep LAN settings of your door
station (Network Settings – LAN) without changing.
The door station will be automatically rebooted after restoring the default settings. All the
parameters, including an IP address and a current date, are set by default.
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
67
13.6. Reboot
The “Reboot” menu is shown below:.
Pic. 13.7
[Reboot]: press this button to reboot the door station. This procedure may last 1-2 minutes.
Enter the administrator password and press the [OK] button to confirm rebooting in the opened
window. Press [Х] to cancel rebooting.
Chapter 13.Config: System
IP Video Door Station DS06M(P) Operation User Manual
68
13.7. System Log
The “System Log” menu is shown below:
Pic. 13.8
The system log contains information about changes of the door station settings and the
system events that happened. The log starts recording information automatically after the device is
switched on.
Date: specify the necessary search period.
Per page: specify the number of lines per a log page.
Press the [Search] button to start searching the events.
Chapter 14.Alarm
IP Video Door Station DS06M(P) Operation User Manual
69
Chapter 14. Alarm
The “Alarm Log” menu is shown below:
Pic. 14.1
This menu has a similar look and functionality as the “System Log” menu (see paragraph
13.7 ), except this menu is used for searching alarm events only .
Chapter 15. Recommendation on Setting and Operation of DS06M(P)
IP Video Door Station DS06M(P) Operation User Manual
70
NOTE!
These settings are audio hardware and software specific and may not be available for all microphones.
Chapter 15. Recommendations on Setting and Operation of DS06M(P)
IP intercom systems include different types and configurations of equipment (PCs, laptops,
microphones, speakers, etc.). Consequently, correct operation of the whole system depends on
proper setting of each device used taking into account the peculiarities of their joint operation.
15.1. Acoustic Echo Cancellation
When using the door station the Client or the Guest may hear an echo feedback from their PC
speakers or the door station speaker accordingly.
The echo feedback on the Guest side (door station speaker) depends on settings of audio
output equipment of Client’s PC as well as on audio settings in the operating system on Client’s PC.
The echo feedback on the Client side (PC speakers) depends on the door station settings.
The echo feedback may occur when one or more of the following conditions are taken place:
Microphone Boost level is too high;
The speakers are too close to the microphone;
The speaker volume is turned up so as the microphone hears the speakers;
The microphone sensitivity is too high.
The most efficient method to remove the echo feedback effect on the Client side is use of
headphones or a hands-free unit by the Client for a conversation with the Guest. If this is impossible
according to some reasons, follow the recommendations below.
There are two main ways of reducing the echo feedback effect: change of audio settings in
the operating system and change of audio settings of the door station.
1. To reduce the echo feedback effect on the Guest side (door station speaker) by changing
settings of the operating system do as follows:
go to Control Panel – Sound – Recording, double-click the recording device set by
default (microphone) and ensure that the “Listen to this device” option is disabled on the
Listen tab.
go to Control Panel – Sound – Playback, double-click the playback device set by default
and ensure that the “Microphone” option is disabled on the Levels tab (button ).
It is also possible to reduce the echo feedback effect by selecting the Enhancements tab on
the microphone properties page and enabling one of the following options:
Enable Noise Suppression
Enable Acoustic Echo Cancellation
Chapter 15. Recommendation on Setting and Operation of DS06M(P)
IP Video Door Station DS06M(P) Operation User Manual
71
NOTE!
The names of options in the OS menus may differ from the ones mentioned above.
2. Some features of functionality of the door station can be effectively used to reduce the echo
feedback effect on the Client side (PC speakers). In the Web User Interface menu go to Config –
Audio Settings – Audio Parameters and put a tick near “Echo Cancellation”.(to get access to the
Web User Interface please refer to paragraph 3.1).
15.2. Sound Gain and Volume Adjusting
1. If the Client can’t hear the Guest well or his voice is interrupted, or if the Guest hears his
echo, then change your operating system settings as follows:
go to Control Panel – Sound – Recording, double-click the recording device set by
default (microphone) and reduce microphone boost level and volume level (if necessary)
on the Levels tab. It is recommended to set microphone boost level to 0 dB, volume level
to 100. It is also necessary to ensure that the “Listen to this device” option is disabled on
the Listen tab.
reduce volume level of the PC speakers to the minimal appropriate level. If it is too high,
then the microphone may receive the audio waves from the speakers and, therefore, the
Guest may hear his echo as well as the Client may hear the Guest with interrupts.
place the PC microphone farther from the speakers and closer to Client’s face.
Moreover, you can adjust the gain of sound transmitted from the door station microphone to
the PC speakers in the Web User Interface. Go to Config – Audio Settings – Audio Parameters
and change the “Input Volume” parameter to the appropriate value. The lower “Input Volume” value,
the quieter Guest’s voice and his echo, and vice versa.
2. If the Guest can’t hear the Client well or his voice is interrupted, then change your operating
system settings as follows:
go to Control Panel – Sound – Recording, double-click the recording device set by
default (microphone) and increase microphone boost level on the Levels tab. Then, set
appropriate volume level. It is recommended to set microphone boost level to 0 dB, volume
level to 100. Values of the parameters may vary depending on the PC microphone type.
ensure that the “Listen to this device” option is disabled on the Listen tab.
reduce volume level of the PC speakers to the minimal appropriate level.
Moreover, you can adjust the gain of sound transmitted from the PC microphone to the door
station speaker in the Web User Interface. Go to Config – Audio Settings – Audio Parameters and
change the “Output Volume” parameter to the appropriate value. The lower “Output Volume” value,
the quieter Client’s voice and his echo, and vice versa.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
72
Parameter
Value
IP address
192.168.0.99
Subnet mask
255.255.255.0
Gateway
192.168.0.1
Username (administrator)
admin
Password (administrator)
admin
HTTP port
80
Data port
5000
RTSP port
554
ONVIF port
2000
NTP-server
time.nist.gov
time.windows.com
time-nw.nist.gov
time-a.nist.gov
time-b.nist.gov
Appendices
Appendix A. Factory Defaults
You can see some of the factory default parameters below.
Appendix B. Maintenance
It is recommended to clean the camera lens once a month by using a cotton swab (3mm)
soaked in industrial alcohol
If regular cleaning is not performed the image quality will deteriote.
Pic. B1
Appendices
IP Video Door Station DS06M(P) Operation User Manual
73
ATTENTION!
It is necessary to provide a connection channel between the devices (door station and PC with the
application) for the direct connection. Pay attention that the Port 5060 is only used for establishing
connection, but data are transferred via RTP (the range of port numbers by default is 1024-65535). The
devices need be accessible via these ports for correct SIP operation.
.
Appendix C. SIP settings example
C1. Direct Connection
Setting the SIP direct connection using the MicroSIP application is given for example. In
case of using other applications the setting is done in a similar way.
Install and run MicroSIP. The application window is shown below:
example, PC).
Pic. C1
Go to the door station web interface menu for setting SIP connection.
You only need specify the following parameters for the SIP direct connection:
Enable SIP #1: enable the SIP option.
Name: enter a device name for its easy identification.
Number: enter the door station IP address.
Call recipient #1: enter the IP address of the device which will receive the call (for
To apply new settings click [Save] (Pic. C2).
Appendices
IP Video Door Station DS06M(P) Operation User Manual
74
If the settings are correct then you will see the following window after pressing the call
button of a door station:
You can answer or cancel the call.
Setting the SIP direct connection is finished.
Pic. C2
Pic. C3
Appendices
IP Video Door Station DS06M(P) Operation User Manual
75
ATTENTION!
It is necessary to provide a connection channel between the devices (door station and PC with the
application) in case of using a SIP server. Pay attention that the Port 5060 is only used for establishing
connection, but data are transferred via RTP (the range of port numbers by default is 1024-65535). The
devices need be accessible via these ports for correct SIP operation.
C2. SIP server
Setting connection via a SIP server using the MicroSIP application is given for example. In
case of using other applications the setting is done in a similar way.
Install and run MicroSIP. The application window is given on the Picture B1. Click Menu –
Add account:
Pic. C4
Enter the following main data:
SIP server: your SIP server address.
User: your account username.
Domain: your account domain.
Login: username for authentication.
Password: your account password.
STUN server: enter the STUN server address to access via NAT.
If necessary you can also enter additional parameters. To apply new settings click [Save].
Appendices
IP Video Door Station DS06M(P) Operation User Manual
76
NOTE:
Contact your system administrator for local SIP server settings. If you have no a local SIP server then you
can use any Internet SIP server you prefer.
Go to the door station web interface menu for setting SIP connection.
You commonly need specify the following parameters:
Enable SIP #1: enable a SIP option.
Name: enter the name to identify a door station.
Number: enter the SIP number for your account.
Username: enter the username for authentication.
Password: enter the password for authentication.
SIP port: enter the SIP port (by default – 5060).
Allow registration: use a SIP server.
Registration server: enter the domain address for your SIP account.
SIP server: enter the address of your SIP server.
Call recipient #1: enter the SIP number of the device which will receive the call (for
example, SIP number of a PC).
STUN IP: enter the STUN server address to access via NAT.
To apply new settings click [Save] (Pic. C5).
Pic. C5
Appendices
IP Video Door Station DS06M(P) Operation User Manual
77
If the settings are correct then you will see the following window after pressing the call
button of a door station:
You can answer or cancel the call.
The setting is finished
Pic. С6
Appendices
IP Video Door Station DS06M(P) Operation User Manual
78
Appendix D. SIP Hardware and Software (for transmitting video and sound via
SIP) Compatibility Lists
D1. PBX Compatibility
3CX
Asterisk 11
Asterisk 12
D2. Software Compatibility
Jitsy 2.8.5426 (Windows Desktop, Mac OS X, Linux)
MicroSIP 3.12.1 (Windows Desktop)
Linphone 3.9.1 (Windows Desktop, Android)
Grandstream Wave (Android, iOS)
D3. Hardware Compatibility
Grandstream GXV3240, GXV3275 videophones
Yealink SIP VP-T49G
Appendices
IP Video Door Station DS06M(P) Operation User Manual
79
Appendix E. Glossary
Client is person who controls a door station using computer.
Door Station Controller is used for powering the door station, network connection,
processing the signal of door opening and signals of other devices that can be connected to the
door station.
Guest is a person who presses the call button on a door station installed outside.
IP Video Door Station is a device which is used for controlling the access to some territory
or building and provides video surveillance functions due to a built-in IP video camera. The call
from the Guest (as he presses the call button) is sent from the door station to the Client’s PC or
laptop with the installed application. The Client can see the Guest on the monitor of his PC and talk
with him using a microphone and speakers / headphones. The Client can control the electronic
door lock and some other devices connected to the door station controller.
PoE Injector is a device that stands between a regular Ethernet switch and the powered
device (for example, door station PoE supported controller), injecting power and transferring the
data via the same cable.
3GP (3GPP file format) is a multimedia container format defined by the Third Generation
Partnership Project (3GPP) for 3G UMTS multimedia services. It is used on 3G mobile phones but
can also be played on some 2G and 4G phones.
ActiveX is a standard that enables software components to interact with one another in a
networked environment, regardless of the language(s) used to create them. Web browsers may
come into contact with ActiveX controls, ActiveX documents, and ActiveX scripts. ActiveX controls
are often downloaded and installed automatically as required.
Asymmetric Digital Subscriber Line (ADSL) is an obsolete type of Digital Subscriber Line
technology, a data communications technology that enables faster data transmission over copper
telephone lines than a conventional voiceband modem can provide.
Angle is the field of view, relative to a standard lens in a 35mm still camera, expressed in
degrees, e.g. 30°. For practical purposes, this is the area that a lens can cover, where the angle of
view is determined by the focal length of the lens. A wide-angle lens has a short focal length and
covers a wider angle of view than standard or telephoto lenses, which have longer focal lengths.
ARP (Address Resolution Protocol) is used to associate an IP address to a hardware
MAC address. A request is broadcast on the local network to discover the MAC address for an IP
address.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
80
Aspect ratio is a ratio of width to height in images. A common aspect ratio used for
television screens and computer monitors is 4:3. High-definition television (HDTV) uses an aspect
ratio of 16:9.
Authentication is the process of identifying an individual, usually based on a user name
and password. In security systems, authentication is distinct from authorization, which is the
process of giving individuals access to system objects based on their identity. Authentication
merely ensures that the individual is who he or she claims to be, but says nothing about the access
rights of the individual.
Autoiris (or DC-Iris).This special type of iris is electrically controlled by the camera, to
automatically regulate the amount of light allowed to enter.
Bit rate: (in kbit/s or Mbit/s) is often referred to as speed, but actually defines the number of
bits/time unit and not distance/time unit.
Backlight Compensation compensates for strong backlighting, so that subjects appear
clearly instead of as silhouettes.
Bonjour, also known as zero-configuration networking, Bonjour enables automatic
discovery of computers, devices, and services on IP networks. Bonjour allows devices to
automatically discover each other without the need to enter IP addresses or configure DNS
servers. Bonjour is developed by Apple Computer Inc.
CCD (Charged Coupled Device). This light-sensitive image device used in many digital
cameras is a large integrated circuit that contains hundreds of thousands of photo-sites (pixels)
that convert light energy into electronic signals. Its size is measured diagonally and can be 1/4",
1/3", 1/2" or 2/3".
CGI (Common Gateway Interface) is a specification for communication between a web
server and other (CGI) programs. For example, a HTML page that contains a form might use a CGI
program to process the form data once it is submitted.
Classless Inter Domain Routing (CIDR) is a method for assigning IP addresses without
using the standard IP address classes like Class A, Class B or Class C. In CIDR notation, an IP
address is represented as A.B.C.D /n, where "/n" is called the IP prefix or network prefix. The IP
prefix identifies the number of significant bits used to identify a network. For example, 192.9.205.22
/18 means, the first 18 bits are used to represent the network and the remaining 14 bits are used to
identify hosts. Common prefixes are 8, 16, 24, and 32.
Complementary metal–oxide–semiconductor (CMOS) is a technology for constructing
integrated circuits. CMOS technology is used in microprocessors, microcontrollers, static RAM,
and other digital logic circuits. CMOS technology is also used for several analog circuits such as
image sensors (CMOS sensor), data converters, and highly integrated transceivers for many types
of communication.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
81
Dynamic DNS is a method/protocol/network service that provides the capability for a
networked device, such as a router or computer system using the Internet Protocol Suite, to notify
a Domain Name System (DNS) name server to change, in real time, the active DNS configuration
of its configured hostnames, addresses or other information.
DHCP (Dynamic Host Configuration Protocol) is a protocol that lets network
administrators automate and centrally manage the assignment of Internet Protocol (IP) addresses
to network devices in a network. DHCP uses the concept of a "lease" or amount of time that a
given IP address will be valid for a computer. The lease time can vary, depending on how long a
user is likely to require the network connection at a particular location. DHCP also supports static
addresses for e.g. computers running web servers, which need a permanent IP address.
Digital zoom is a method of decreasing (narrowing) the apparent angle of view of a digital
photographic or video image. Digital zoom is accomplished by cropping an image down to a
centered area with the same aspect ratio as the original, and usually also interpolating the result
back up to the pixel dimensions of the original. It is accomplished electronically, with no adjustment
of the camera optics, and no optical resolution is gained in the process.
Domain server can also be used by organizations that wish to centralize the management
of their (Windows) computers. Each user within a domain has an account that usually allows them
to log in to and use any computer in the domain, although restrictions may also apply. The domain
server is the server that authenticates the users on the network.
Ethernet is the most widely installed local area network technology. An Ethernet LAN
typically uses special grades of twisted pair wires. The most commonly installed Ethernet systems
are 10BASE-T and 100BASE-T10, which provide transmission speeds up to 10 Mbps and 100
Mbps respectively.
Factory default settings are the settings that originally applied for a device when it was
first delivered from the factory. If it should become necessary to reset a device to its factory default
settings, this will, for many devices, completely reset any settings that were changed by the user.
Firewall works as a barrier between networks, e.g. between a Local Area Network and the
Internet. The firewall ensures that only authorized users are allowed to access the one network
from the other. A firewall can be software running on a computer, or it can be a standalone
hardware device.
Focal length is measured in millimeters; the focal length of a camera lens determines the
width of the horizontal field of view, which in turn is measured in degrees.
FPS (frames per second) a measure of how much information is used to store and display
motion video. The term applies equally to film video and digital video. Each frame is a still image;
displaying frames in quick succession creates the illusion of motion. The more frames per second
(fps), the smoother the motion appears.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
82
Frame is a complete video image. In the 2:1 interlaced scanning format of the
RS-170 and CCIR formats, a frame is made up of two separate fields of 262.5 or 312.5 lines
interlaced at 60 or 50 Hz to form a complete frame, which appears at 30 or 25 Hz. In video
cameras with a progressive scan, each frame is scanned line-by-line and not interlaced; most are
also displayed at 30 and 25 Hz.
FTP (File Transfer Protocol) is an application protocol that uses the TCP/IP protocols,
used to exchange files between computers/devices on networks.
Full-duplex means transmission of data in two directions simultaneously. In an audio
system this would describe e.g. a telephone system. Half-duplex also provides bi-directional
communication, but only in one direction at a time, as in a walkie-talkie system.
G.711 is the default pulse code modulation (PCM) standard for Internet Protocol (IP) private
branch exchange (PBX) vendors, as well as for the public switched telephone network (PSTN).
G.711 digitizes analog voice signals producing output at 64 kilobits per second (Kbps).
Gain is the amplification factor and the extent to which an analog amplifier boosts the
strength of a signal. Amplification factors are usually expressed in terms of power. The decibel (dB)
is the most common way of quantifying the gain of an amplifier.
Gateway is a point in a network that acts as an entry point to another network. In a
corporate network for example, a computer server acting as a gateway often also acts as a proxy
server and a firewall server. A gateway is often associated with both a router, which knows where
to direct a given packet of data that arrives at the gateway, and a switch, which furnishes the actual
path in and out of the gateway for a given packet.
HTTP (Hypertext Transfer Protocol) is the set of rules for exchanging files (text, graphic
images, sound, video, and other multimedia files) on the web. The HTTP protocol runs on top of
the TCP/IP suite of protocols.
HTTPS (Hypertext Transfer Protocol over SSL) is a web protocol used by browsers and
web servers to encrypt and decrypt user page requests and the pages returned by the server. The
encrypted exchange of information is governed by the use of an HTTPS certificate (issued by a
Certificate Authority), which guarantees the authenticity of the server.
Hub is used to connect multiple devices to the network. The hub transmits all data to all
devices connected to it, whereas a switch will only transmit the data to the device it is specifically
intended for.
ICMP is a network protocol useful in Internet Protocol (IP) network management and
administration. ICMP is a required element of IP implementations. ICMP is a control protocol,
meaning that it does not carry application data, but rather information about the status of the
network itself.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
83
IEEE 802.11 is a family of standards for wireless LANs. The 802.11 standard supports 1 or
2 Mbit/s transmission on the 2.4 GHz band. IEEE 802.11b supports data rates up to11 Mbit/s on
the 2.4 GHz band, while 802.11g allows up to 54 Mbit/s on the 5 GHz band.
Interlacing. Interlaced video is video captured at 50 pictures (known as fields) per second,
of which every 2 consecutive fields (at half height) are then combined into 1 frame. Interlacing was
developed many years ago for the analog TV world and is still used widely today. It provides good
results when viewing motion in standard TV pictures, although there is always some degree of
distortion in the image.
Internet Explorer (formerly Microsoft Internet Explorer, commonly abbreviated IE or MSIE)
is a series of graphical web browsers developed by Microsoft and included as part of the Microsoft
Windows line of operating systems, starting in 1995.
IP66 is a two digit number developed by the international electrical Commission, and is
used to provide Ingress Protection (IP) rating to a piece of electronic equipment or to an enclosure
for electronic equipment. The Ingress protection code indicates the level and amount of protection.
The first digit means no ingress of dust; complete protection against contact. The second digit
means water projected in powerful jets (12.5mm nozzle) against the enclosure from any direction
shall have no harmful effects.
IP camera. The terms IP camera, network camera and Internet camera all refer to the
same thing - a camera and computer combined in one unit. It operates as stand-alone unit and
only requires a connection to the network.
JPEG (Joint Photographic Experts Group).Together with the GIF file format, JPEG is an
image file type commonly used on the web. A JPEG image is a bitmap, and usually has the file
extension ‘.jpg’ or “.jpeg.” When creating a JPEG image, it is possible to configure the level of
compression to use. As the lowest compression (i.e. the highest quality) results in the largest file,
there is a trade-off between image quality and file size.
kbit/s (kilobits per second) is a measure of the bit rate, i.e. the rate at which bits are
passing a given point. See also Bit rate.
LAN (Local Area Network) is a group of computers and associated devices that typically
share common resources within a limited geographical area.
Lux is a standard unit of illumination measurement.
MAC address (Media Access Control address) is a unique identifier associated with a
piece of networking equipment, or more specifically, its interface with the network. For example,
the network card in a computer has its own MAC address.
Mbit/s (Megabits per second) is a measure of the bit rate, i.e. the rate at which bits are
passing a given point. Commonly used to give the “speed” of a network. A LAN might run at 10 or
100 Mbit/s.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
84
Motion JPEG is a simple compression/decompression technique for network video.
Latency is low and image quality is guaranteed, regardless of movement or complexity of the
image. Image quality is controlled by adjusting the compression level, which in turn provides
control over the file size, and thereby the bit rate.
MPEG-4 is a group of audio and video coding standards and related technology. The
primary uses for the MPEG-4 standard are web (streaming media) and CD distribution,
conversational (videophone), and broadcast television. Most of the features included in MPEG-4
are left to individual developers to decide whether to implement them or not. This means that there
are probably no complete implementations of the entire MPEG-4 set of standards. To deal with
this, the standard includes the concept of "profiles" and "levels", allowing a specific set of
capabilities to be defined in a manner appropriate for a subset of applications.
Multicast is a bandwidth-conserving technology that reduces bandwidth usage by
simultaneously delivering a single stream of information to multiple network recipients.
Network Time Protocol (NTP) is a protocol for synchronizing the clocks of computer
systems over packet-switched, variable-latency data networks. It is designed particularly to resist
the effects of variable latency by using a jitter buffer.
NTSC (National Television System Committee) is an analog color encoding system used
in television systems in Japan, the United States and other parts of the Americas. NTSC defines
the video signal using 525 TV lines per frame, at a refresh rate equal to 30 frames per second. See
also PAL.
ONVIF (Open Network Video Interface Forum) is a global and open industry forum with
the goal to facilitate the development and use of a global open standard for the interface of
physical IP-based security products. Or in other words, to create a standard for how IP products
within video surveillance and other physical security areas can communicate with each other.
ONVIF is an organization started in 2008 by Axis Communications, Bosch Security Systems and
Sony.
PAL (Phase Alternating Line) is an analog color encoding system used in television
systems in Europe and in many other parts of the world. PAL defines the video signal using 625 TV
lines per frame, at a refresh rate equal to 25 frames per second.
Power over Ethernet or PoE provides power to a network device via the same cable as
used for the network connection. This is very useful for IP-Surveillance and remote monitoring
applications in places where it may be too impractical or expensive to power the device from a
power outlet.
PPP (Point-to-Point Protocol) is a protocol that uses a serial interface for communication
between two network devices. For example, a PC connected by a phone line to a server.
Point-to-Point Protocol over Ethernet (PPPoE) is a network protocol for encapsulating
Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with DSL services
Appendices
IP Video Door Station DS06M(P) Operation User Manual
85
where individual users connect to the DSL modem over Ethernet and in plain Metro Ethernet
networks.
Progressive scan, as opposed to interlaced video, scans the entire picture, line by line
every sixteenth of a second. In other words, captured images are not split into separate fields as in
interlaced scanning.
Jack-45 is an eight-wire connector used to connect computers onto a local-area networks
(LAN), especially Ethernets. RJ-45 connectors look similar to the RJ-11 connectors used for
connecting telephone equipment, but they are a bit wider.
Router is a device that determines the next network point to which a packet should be
forwarded on its way to its final destination. A router creates and/or maintains a special routing
table that stores information on how best to reach certain destinations. A router is sometimes
included as part of a network switch.
RTP is an Internet protocol for the transport of real-time data, e.g. audio and video. It can
be used for media-on-demand as well as interactive services such as Internet telephony.
RTSP (Real Time Streaming Protocol) is a control protocol, and a starting point for
negotiating transports such as RTP, multicast and Unicast, and for negotiating codecs.
RTSP can be considered a “remote control” for controlling the media stream delivered by a
media server. RTSP servers typically use RTP as the protocol for the actual transport of
audio/video data.
Shutter is the device on the camera that opens and closes to control how long the focal
plane is exposed to light.
SMTP is used for sending and receiving e-mail. However, as it is “simple,” it is limited in its
ability to queue messages at the receiving end, and is usually used with one of two other protocols,
POP3 or IMAP. These other protocols allow the user to save messages in a server mailbox and
download them periodically from the server.
SMTP authentication is an extension of SMTP, whereby the client is required to log into the
mail server before or during the sending of email. It can be used to allow legitimate users to send
email while denying the service to unauthorized users, such as spammers.
SSL/TLS (Secure Socket Layer/Transport Layer Security). These two protocols (SSL is
succeeded by TLS) are cryptographic protocols that provide secure communication on a network.
SSL is commonly used over HTTP to form HTTPS, as used e.g. on the Internet for electronic
financial transactions. SSL uses public key certificates to verify the identity of the server.
Subnet & subnet mask is an identifiably separate part of an organization network.
Typically, a subnet may represent all the machines at one geographic location, in one building, or
on the same local area network (LAN). Having an organization network divided into subnets allows
it to be connected to the Internet with a single shared network address.
The subnet mask is the part of the IP address that tells a network router how to find the subnet that
Appendices
IP Video Door Station DS06M(P) Operation User Manual
86
the data packet should be delivered to. Using a subnet mask saves the router having to handle the
entire 32-bit IP address; it simply looks at the bits selected by the mask.
Switch is a network device that connects network segments together, and which selects a
path for sending a unit of data to its next destination. In general, a switch is a simpler and faster
mechanism than a router, which requires knowledge about the network and how to determine the
route. Some switches include the router function.
TCP is used along with the Internet Protocol (IP) to transmit data as packets between
computers over the network. While IP takes care of the actual packet delivery, TCP keeps track of
the individual packets that the communication (e.g. requested a web page file) is divided into, and,
when all packets have arrived at their destination, it reassembles them to re-form the complete file.
TCP is a connection-oriented protocol, which means that a connection is established
between the two end-points and is maintained until the data has been successfully exchanged
between the communicating applications.
Time to live (TTL) is mechanism that limits the lifespan of data in a computer or network.
TTL may be implemented as a counter or timestamp attached to or embedded in the data. Once
the prescribed event count or timespan has elapsed, data is discarded. In computer networking,
TTL prevents a data packet from circulating indefinitely. In computing applications, TTL is used to
improve performance of caching or improve privacy.
UDP is a communications protocol that offers limited service for exchanging data in a
network that uses the Internet Protocol (IP). UDP is an alternative to the Transmission Control
Protocol (TCP). The advantage of UDP is that it is not required to deliver all data and may drop
network packets when there is e.g. network congestion. This is suitable for live video, as there is
no point in re-transmitting old information that will not be displayed anyway.
Universal Plug and Play (UPnP) is a set of networking protocols for primarily residential
networks without enterprise class devices that permits networked devices, such as personal
computers, printers, Internet gateways, Wi-Fi access points and mobile devices to seamlessly
discover each other's presence on the network and establish functional network services for data
sharing, communications, and entertainment.
Uniform Resource Locator or Unified Resource Locator (URL) is a character string that
specifies where a known resource is available on the Internet and the mechanism for retrieving it.
Wireless Application Protocol (WAP) is a technical standard for accessing information
over a mobile wireless network. A WAP browser is a web browser for mobile devices such as
mobile phones (called "cellular phones" in some countries) that uses the protocol.
Web server is a program, which allows Web browsers to retrieve files from computers
connected to the Internet. The Web server listens for requests from Web browsers and upon
receiving a request for a file sends it back to the browser.
Appendices
IP Video Door Station DS06M(P) Operation User Manual
87
The primary function of a Web server is to serve pages to other remote computers;
consequently, it needs to be installed on a computer that is permanently connected to the Internet.
It also controls access to the server whilst monitoring and logging server access statistics.
Wireless LAN is a wireless local area network that uses radio waves as its carrier: where
the network connections for end-users are wireless. The main network structure usually uses
cables.
Loading...