Bertazzoni X304GGVVE, X304GGVNE, X304GGVCR, X304GGVVI, X304GGVBI User Manual

Installation, Service and User Instructions

FREESTANDING GAS RANGES

BERTAZZONI

DIMENSIONS: 30’’ (762 mm)(W) x 253/16’’ (640 mm)(D) x36’’ (915 mm)(H)

MODELS

X304GGVX [M7S0GTU4X(2 or 5)A]

X304GGVBI [M7S0GTU4W(2 or 5)A]

X304GGVCR

[M7S0GTU4D(2 or 5)A]

X304GGVGI [M7S0GTU4I(2 or 5)A]

X304GGVRO

[M7S0GTU4R(2 or 5)A]

X304GGVVI [M7S0GTU4L(2 or 5)A]

X304GGVVE

X304GGVBL

[M7S0GTU4V(2 or 5)A]

[M7S0GTU4U(2 or 5)A]

X304GGVNE [M7S0GTU4N(2 or 5)A]

Note: coloured parts employed on coloured models have same identical drawings and dimensions of the same
INOX parts already supplied for the basic INOX models; for this reason the ref. Frawing are the same and they
have not been supplied.

310356

IMPORTANT - PLEASE READ AND FOLLOW

-Before beginning installation, please read these instructions completely and carefully.

-Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local
and national codes and ordinances.

-Please ensure that this product is properly grounded.

-The installer should leave these instructions with the consumer who should retain for local inspector's use and for
future reference.

-The electrical plug should always be accessible.

Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1-latest edition. Electrical
installation must be in accordance with the National Electrical Code, ANIS/NFPA70
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B
Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve must be installed in the gas
supply line ahead of the oven in the gas flow for safety and ease of service.

In Massachusetts: All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" handle type manual

gas valve must be installed in the gas supply line to this appliance.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE.

Warning!

- This range can tip. Injury to persons could result.

- Install anti-tip device shipped with range.

-See Installation Instructions

- latest edition and/or local codes. IN CANADA:

149.2, Propane

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
OBSERVE ALL GOVERNING CODES AND ORDINANCES.

WARNING: If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury
or death.

Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

- Do not light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow

the gas supplier’s instructions.

- If you cannot reach your gas suppliers, call the fire department.

Installation and service must be performed by a qualified installer,
service agency or the gas supplier.

WARNING

Read this instruction booklet before installing and using the appliance.

The manufacturer will not be responsible for any damage to property or to persons caused by
incorrect installation or improper use of the appliance.

The manufacturer reserves the right to make changes to its products when considered necessary and useful,
without affecting the essential safety and operating characteristics.

This appliance has been designed for non-professional, domestic use only.

2

Warning: do not place any pot or pan on the open oven door. The door is made of glass and it can
break if loaded with a weight.

Warning: this appliance must be used only with base feet properly installed. See installation
instruction for details.

Installation instructions

This appliance shall only be installed by an authorized person. This appliance shall be installed in
accordance with the manufacturer’s installation instructions, IMPORTANT: this appliance must be
installed in accordance with the norms & standards of the country where it will be installed.

The installation of this appliance must conform to local codes and ordinances. In the absence of
local codes, Installations must conforms to American National Standards, National Fuel Gas Code

ANSI Z223.1 – latest edition** or B149.1.

If local codes permit, a flexible metal appliance connection with the new AGA or CGA certified
design, max. 5 feet (1,5 m) long, ½” I.D. is recommended for connecting this appliance to the gas
supply line. Do not bend or damage the flexible connector when moving the appliance. The pressure
regulator has ½” female pipe thread. The appropriate fitting must be determined based on the size of
your gas supply line, the flexible metal connector and the shutoff valve.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in
the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.

The appliance must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal
to or less than ½ psi (3.5 kPa).

For use with a pressure regulator. The regulator supplied must be used with this appliance; it shall
be properly installed in order to be accessible when appliance is installed in its final location.

The gas appliance pressure regulator must be set for the gas with which the appliance is used.

This appliance can be used with Natural Gas and LP Gas. It is shipped from the factory adjusted for
use with LP Gas: CONVERSION FIXED ORIFICES ARE LOCATED IN THE LITERATURE PACK
SUPPLIED WITH THE UNIT.

A gas nozzle kit for the change of type of gas are contained inside the package together with the
gas appliance installation kit and instruction booklet.

The maximum inlet gas supply pressure incoming to the gas appliance pressure regulator is 20’’
water column (5 kPa) .

The minimum gas supply pressure for checking the regulator setting shall be at least 1“ w.c. (249 Pa)
above the inlet specified manifold pressure to the appliance (this operating pressure is 11” w.c. (2.75
kPa) for LP Gas and 4” w.c. (1.00 kPa for Natural Gas).

All opening and holes in the wall and floor, back and under the appliance shall be sealed before
installation of the appliance.

It’s always compulsory to install the riser even for an island installation

ATTENTION: A manual valve shall be installed in an accessible location in the gas line external to the
appliance for the purpose of turning on or shutting off gas to the appliance

WARNING: Do not use aerosol sprays in the vicinity of this appliance while it is in operation

Requirements
Room ventilation – Location and venting.
ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in
conformity with the appropriate national and local standards.
ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be
installed in conformity with the appropriate national and local standards.

3

INSTALLATION MANUAL

ANTI-TIP STABILlTY DEVICE INSTALLATION INSTRUCTIONS

1. The anti-tip bracket have to be installed to the rear wall as shown. The height for the bracket location from

the floor has to be determined after the range legs have been adjusted to the proper installation height - as
shown in the installation instructions – and after the range has been leveled.

2. Measure from the floor to the bottom of the anti-tip bracket location on the back of the range.

3. Position the two anti-tip brackets on the wall at the measured dimension plus 1/8" (0.32 cm). The brackets

have to be placed at 2”5/16 (6,0 cm) from the side of the range. The distance between the two bracket is
31”1/4 (79,3 cm) clearance. Secure with suitable inserts.

4. Slide the range against the wall until the brackets are fully inserted into the holes on the backside of the

range..

Height adjustable legs:

1. Legs are packed in the top box.

2. Legs should be installed with the appliance being near the location of final installation, they are not secure

for long transport. After unpacking the range, raise it about a foot to insert the legs in their bases assembled
on the lower part of the cooker and lower the range gently to keep any undue strain from legs and mounting
hardware. It is recommended to use a pallet or lift jack instead of tilting the unit.

4

BACKGUARD INSTALLATION INSTRUCTION

It’s always compulsory to installa the riser even for an island installation

1) Remove n°2 screws fixing worktop as shown in fig.1

2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in

fig .2

3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.3)

4) Assemble back part with front part of the backguard and fix them with a screws supplied with the backguard kit

(fig.4)

1 2

3 4

WORKTOP FRONTGUARD INSTALLATION INSTRUCTIONS

In order to increase the clearance between front edge of the worktop and the burners for your safety it is
recomended to install the worktop frontguard supplied with the appliance. For installation instructions follow
the instructions indicated in the following figures

5

INSTALLATION SIDE-BY-SIDE TO KITCHEN CABINET

1. This range may be installed directly adjacent to existing 36" (91.5 cm) high cabinets. IMPORTANT: The

top border of the worktop should be at the same level of the adjacent

accomplished by raising the unit using the adjustment spindles on the legs.

2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other vertical

above

3. Within the side clearance to combustible vertical surfaces above 36" (91.5 cm) , the maximum wall cabinet depth must

be 13" (33.0 cm) and wall cabinets within this side clearance must be 18" (45.7

countertop hightness shall be from

36" (91.4 cm) high. There must be a minimum of 6" (15.2 cm) side clearance.

35”1/2(90,2 cm) to 37” ¼ (94,6 cm).

cabinet countertop. This can be

surfaces

cm) above countertop level and

A 30” (76,2 cm)
B 36” (91,5 cm)
C 13” (33,0 cm)
D 18” (45,7 cm)
E 35”1/2(90,2 cm) / 37” ¼ (94,6 cm)
F 6” (15,2 cm)
G 6” (15,2 cm)

6

COOKER HOOD INSTALLATION

The bottom of the hood should be 25
typically result in the bottom of the hood being 61
for other minimum clearance requirements mandated by specific local or regional installation codes. Refer to
the rangehood installation instructions for additional information. These dimensions provide for safe and
efficient operation of the hood.

1/2" (65 cm) min. to 31 1/2" (80 cm) above the countertop. This would

1/2" (156.2 cm) to 67 1/2" (171.5 cm) above the floor. Check

ELECTRICAL CONNECTION

This unit is manufactured for a polarized, grounded 120 VAC/60 Hz, 15A 3 pin-earthed receptacle. Electric
power consumption is about 150 W. The minimum of 102 VAC is required for proper operation of gas ignition
systems. This circuit must be grounded and properly polarized. The unit is equipped witth a SJT power cord.
In case of replacement, the cable shall be replaced with one of the same type, size and length.

WARNING

Cooling fan failure.

In case of a cooling fan failure the frontal red indicator "Fan Failure" will light up. If this happens, please turn
off the appliance immediately, call the nearest after sale assistance service center and do not use the
appliance until the cooling fan system of the appliance has been properly repaired by a qualified technician.

WARNING

Electrical Grounding Instructions
This appliance is equipped with a three-prong plug for your protection against shock hazard and should be
plugged directly into a properly grounded socket. Do not cut or remove the grounding prong from this plug.

WARNING

ELECTRICAL SHOCK HAZARD

• Disconnect electrical power at the circuit breaker box or fuse box before installing the gas cooker

• Electrically ground gas cooker

• Use copper conductors only. Failure to follow these instructions could resul in serious injury or death

7

Wiring diagram
For freestanding gas range model X304GGVX M7S0GTU4X(2 or 5)A

CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation.
Verify proper operation after servicing.

GAS CONNECTION

All gas connections must be made according to national and local codes. The gas supply (service) line must be the same
size or greater than the inlet line of the appliance. This range uses a 1/2" NPT inlet (see fig. in this chapter for details of
gas connections installations).On all pipe joints use sealant resistant to LP gas.

1. Manual Shut-off Valve:

This installer-supplied valve must be installed in the gas service line ahead of the appliance in the gas flow and in a
position where it can be reached quickly in the event of an emergency. The manual shut-off valve shall be installed
properly in order to be accessible when the appliance is installed. In Massachusetts: A 'T' handle type manual gas
valve must be installed in the gas supply line to this appliance.

2. Pressure Regulator(see fig. in this chapter)

a) All cooking equipment must have a pressure regulator on the incoming service line for safe and efficient

operation, since service pressure may fluctuate with local demand. The pressure regulator is supplied
separately with the appliance; regulator has two female threads ½” NPT; it shall be installed properly in order
to be accessible when appliance is installed in final position.

b) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service

company. Please provide the service person with this manual before work is started on the range. (Gas
conversions are the responsibility of the dealer or end user.)

c) This range can be used with Natural or LP/Propane gas. It is shipped from the factory adjusted for use with

natural gas.

d) Manifold pressure should be checked with a manometer, natural gas requires 4.0" W.c.P. and LP/Propane
requires 11.0" W.C.P. Incoming line pressure upstream from the regulator must be 1" W.c.P. higher than the

manifold pressure in order to check the regulator. The regulator used on this range can withstand a
maximum input pressure of 1/2 PSI (14.0" W.c.P.) If the line pressure is in excess of that amount, a step­down regulator will be required.

e) The appliance, its individuai shut-off valve, and pressure regulator must be disconnected from the gas

supply piping system during any pressure testing of that system at pressures in excess of 1/2 psig (3.45

kPa).
f) The appliance must be isolated from the gas supply piping system by closing its individuai manual shut-off
valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2
psig (3.45 kPa).

8

3. Flexible Connections:
a) If the unit is to be installed with flexible couplings and/or quick disconnect fittings, the installer must use a
heavy-duty, AGA design-certified commerciai flexible connector of at least 1/2" (1.3 cm) ID NPT (with
suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69 standards.
b) In Massachusetts: The unit must be installed with a 36" (3-foot) long flexible gas connector.
c) In Canada: CAN 1-6.10-88 metal connectors for gas appliances and CAN 1-6.9 M79 quick disconnect
device for use with gas fuel.

CAUTlON: Leak testing of the appliance shall be conducted according to the manufacturer's instructions. Before placing
the oven into operation, always check for leaks with a soapy water solution or other acceptable method. DO NOT USE
AN OPEN FLAME TO CHECK FOR LEAKS!

A 2”( 5 cm)

B 3”(7,6 cm)

D 8”(20,3 cm)

A properly-grounded horizontally- mounted electrical receptacle should be installed no higher than 3" (7.6 cm) above the
floor, no less than 2”( 5 cm) and no more than 8”(20,3 cm) from the right side (facing product). Check all local code
requirements.

An agency-approved, properly-sized manual shut-off valve should be installed no higher than 3" (7.6 cm) above the floor
and no less than
shut-off valve and regulator, use agency-approved, properly sized flexible or rigid pipe. Check all local code
requirements.

PERFORMANCE CHECKLlST

All burners are tested before leaving the factory. There are no adjustments for the burners if connected according to the
information on the rating plate. Check each burner for proper operations. Flames should be blue in all settings. If service
is required, contact your dealer for the name of their authorized service agency. Gas conversions and initial installation
are not the responsibility of the manufacturer.

The installer should carry out the following performance checks. Refer to instructions below.

1. Check surface burner ignition.

2. Check air shutter adjustment (only for oven and broiler burner)- sharp blue flame, no yellow tipping, sooting or flame
lifting

3. Check low flame adjustment

4. Check broiler and oven ignition - all burner ports.

5. Check for gas leaks (odors) at all gas connections.

6. Check oven bake and convection bake function.

FINAL PREPARATION

1. Some stainless steel parts may have a plastic protective wrap which must be removed. The interior of the oven

should be washed thoroughly with hot soapy water to remove film residues and any installation dust or debris
before using it for food preparation, then rinsed and wiped dry. Solutions stronger than soap and water are rarely
needed.

2. All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner recommended for

use with stainless steel If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders! If it is
necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the
material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape

stainless steel! Scratches are almost impossible to remove.
NOTE: These installation instructions should remain with the unit for future reference. The electrical diagram is located in
the backside or the appliance.

2”( 5 cm) and no more than 8”(20,3 cm) from the left side (facing product). To connect gas between

9

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the appliance. Replacement parts are available
from factory authorized parts distributors.

Conversion to different types of gas

Before carrying out any maintenance work, disconnect the appliance from the gas and electric
supply. For LP Gas fit regulator assembly described in Fig.

Adaptation of the pressure regulator for use with different type of gas

The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with LP Gas at a
nominal outlet pressure of 11” w.c. or Natural gas at a nominal outlet pressure of 4” w.c. and it is pre-arranged from the
factory to operate with one of these gas/pressure as indicated in the labels affixed on the appliance, package and
Instruction booklet.

To convert the regulator for use with other types of gas follow these instructions:

1) Unscrew by hand the upper metal stopper of the regulator.

2) Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw it again
in opposite way under the metal stopper (for gas reference see the written “LP” and “NAT” with relative indicating arrows
on the white piece).

3) Screw again by hand the metal stopper in the original position on the regulator.

Following these exact instructions the gas regulator is converted for use with the other gas/pressure.

It is essential that the gasket and the pressure test point stopper are properly installed to avoid gas leakage

- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:

To change the nozzles of the burners use the following procedure:
Lift up the burners and unscrew the nozzles ( Fig.) using an adjustable spanner of 7 mm and change the nozzles with
those designed for the new gas supply according to the information given in TABLE shown below.

Follow the instructions below to change the oven burner nozzle:

1) Remove the oven door (Fig. 9A-9B)

2) Remove the lower frontal cavity gasket and the enamelled cavity base plate (Fig. 10)

3) Loosen and the screw V and pull out the burner from the support being careful not to damage the ignition plug and
the thermocouple (Fig. 11)

4) Unscrew the nozzle R (Fig. 11) using a 7 mm. spanner and replace it with the nozzle for the new type of gas
according to what is indicate in the table below

5) Re-install all the parts in revers sequence from 3 to 1

10

Fig. 9A Fig. 9B

Fig. 10 Fig. 11

Follow the instructions below to change the broiler burner nozzle:

1) Loosen the screw and pull out the burner from the support being careful not to damage the ignition plug and the
thermocouple (Fig. 12).

2) Unscrew the nozzle C (Fig. 12) using a 7 mm spanner and replace it with the nozzle needed for the new type of gas
according to what is indicated in TABLE shown below.

Fig. 12

11

Models X304GGVX [M7S0GTU4X (2 or 5)A]

Adapting to different types of gas

CAUTION: save the orifices removed from the appliance for future use

Burner Position Injector Gas Pressure Max Rate Min Rate By-pass

diam. [mm.] Type [i.w.c.] [BTU/h] [W] [BTU/h] [W] diam. [mm]

Auxiliary Rear L 0,90 NG 4” 3400 996 900 264 Regulated

0,54 LP (Propane) 11” 3400 996 900 264 0,29

Semi-Rapid Front R 1,18 NG 4” 6100 1787 1500 439 Regulated

0,70 LP (Propane) 11” 6100 1787 1500 439 0,36

Rapid Rear R 1,55 NG 4” 10400 3047 2500 732 Regulated

0,92 LP (Propane) 11” 10400 3047 2500 732 0,47
Front L Inner 0,80 NG 4” 2800 820 900 264 Regulated

Dual Burner 0,49 LP (Propane) 11” 2800 820 900 264 0,29

Front L Outer N°2 x 1,15 NG 4” 12000 3516 4500 1318 Regulated
N°2 x 0,70 LP (Propane) 11” 12000 3516 4500 1318 0,65

Oven Oven 1,85 NG 4” 14500 4248 3500 1025 Regulated

downside 1,10 LP (Propane) 11” 14500 4248 3500 1025 0,54

Broiler Oven 1,70 NG 4” 12000 3516 Only Max Only Max No by-pass

upside 0,98 LP (Propane) 11” 12000 3516 Only Max Only Max No by-pass

REGULATION OF BURNERS

Primary air adjustment:

Broiler burner adjustment: to adjust the broiler burner loosen screw P and adjust the position X of the Venturi cone

according to the measurements indicated in table 4.

TABLE N°4: Burner primary air regulation (indicative)

Burner
Type of gas Broiler

Inches (mm)
NG (Natural Gas) fully open
LP (Propane Gas) fully open

Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:

1) Light the burner and set the knob to the MINIMUM position (small flame).

2) Remove the knob of the valve that is press fit on the rod of that valve.

3) The cooker is equipped with safety valves, use a small slotted screwdriver the choke valve located on the valve body
and turn the choke screw to the right or left until the burner flame is adjusted to minimum

4) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

Oven burner adjustment: follow the instructions below to adjust the minimum:

1) Light the burner setting the knob to the MAXIMUM position.

2) Close the oven door and operate the oven for at least 10 minutes.

3) Set the knob to the MINIMUM position and then remove it.

4) With a slotted screwdriver turn the choking screw (by-pass screw at the left side of the thermostat bar) and, while
observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on
when switching quickly from the MINIMUM to the MAXIMUM position.

WARNING: The above-mentioned adjustment should be made only for natural gas, while for operation with

liquid gas the screw must be locked at the end in a clockwise direction. The broiler burner always
operates at maximum and therefore no minimum adjustment is required.

12

SERVICE & MAINTENANCE INSTRUCTIONS

Service and maintenance only to be carried out by an authorised person

To replace parts such as burners, valves and electric components, the appliance must be open removing the worktop.

Note: if the valves must be replaced, first disassemble the ignitions switches wires.

It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal between the
body and the gas train.

WARNING: After first installation of the appliance or after any service intervention concerning main gas parts of
the appliance, make the leak test using water with soap on the gas connections in order to verify the correct
installation. Do not use fire for gas leak testing.

To replace the oven bulb, just unscrew the protection cap that projects out inside the oven. (Fig.19) WARNING:
Disconnect power before servicing unit.

In order to remove the oven door make sure to block the ihinges with a screw driver.

Call an autorised service person for this operation that can be dangerous

13

USER MANUAL

WARNINGS:
Do not to cover the holes inside the oven with aluminium paper

Do not to cover the burners of cooktop with aluminium paper

Do not store any flammable objects or objects under pressure in the storage compartment

Keeping appliance area clear and free from combustible materials, gasoline and other flammable
vapors and liquid.
Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a
safe place in order to avoid potential hazards.

Do not use aerosol sprays in the vicinity of this appliance while it is in operation

Do not use oven doors as support or for sit-down.
Do not use oven cavity as storage compartment.

14

CONTROL PANEL DESCRIPTION

On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls that
a cooker can have:

the symbol shows the disposition of burners on the worktop, the full dot identifies the burner in object (in this
case the front burner on the right).

the symbol

the symbol

the symbol

shows the running of oven or broiler

shows the swicth for the oven fan and oven light

shows the swicth for the oven light

USING BURNERS

A diagram is etched on the control panel above each knob which indicates which burner corresponds to that
knob.

Manual ignition:
Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure.
Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star
(large flame) and place a lit match up to the burner.
Automatic electric ignition:
Turn the knob that corresponds to the burner selected anticlockwise direction to the MAXIMUM position at the etched
star (large flame) and then press the knob down to activate the spark ignition. Once ignited, keep pressing the knob for
about 10 seconds to allow the flame to heat the thermocouple. If the burner does not remain alight after releasing the
knob repeat the above procedure,

Note: It is recommended not to try to ignite the burner if the relative flame cap is not in the correct position

Note: Dual burner is composed by two burner (inside and outside); each one operates under the relative gas valve

indipendently from the other one.

Instructions for the ignition of the dual wok burner: turn on the central burner first, then turn on the external ring.

Tips for using burners correctly:

WARNING: During use of each gas burner(s) adjust the burner flame size properly so it does not extend beyond
the edge of the cooking utensil. This is an instruction based on safety considerations

- Use suitable pots for each burner (see Fig. and Table )

- When the liquid is boiling, turn down the knob to the MINIMUM position.

- Always use pots with a cover.

Correct flame aspect: verify that aspect flame of the worktop burners be completely blue and with an aspect as
indicated in figure(flame)

Table

Burner Recommended pan diameters inches (mm)

Small 3½”-51/2”(90 – 140)
Medium 51/2”- 101/4”(140 – 260)
Large 71/8”- 101/4” (180 – 260)
Dual burner 82/3”-101/4” (220 – 260)

(flame)

15

WARNING: check the position of the burner caps before operation.

Correct usage of pans:

- Dry the bottom of the pan before placing it on the hotplate.

- Use pots with a flat, thick bottom, except for wok cooking.

- When using the burners, ensure that the handles of the pans are correctly positioned. Keep children away from the
appliance.

- When cooking foods with oil and fat, which are very flammable, the user should not leave the appliance unattended.

WOK PAN: To use the wok pan, please utilize a suitable wok adaptor grid; wok pan external diameter shall not be less
than 10” (25cm) and not more than 16”(40cm).

WARNING: If the power is cut off, the burners can be lit with matches.
The burners equipped with a safety thermocouple can only be lit when the knob is in the MAXIMUM position (large flame
etching).

USING THE GAS OVEN

All the gas oven cookers are equipped with a thermostat and safety device to adjust the cooking temperature. The oven
temperature is set by turning the knob counterclockwise to match the indicator with the temperature selected. The gas
oven is combined with a gas broiler. See the specific pages for use information.

WARNING: If the burner flames are extinguished accidentally, turn off the control knob and do not try to relight
the oven until after at least 1 minute.

TABLE N°7

THERMOSTAT SETTING TEMPERATURE °F TEMPERATURE °C
MIN.

MED-LOW
MED.
MED-HI

MAX.

270 132
320 160
350 175
425 220
500 260

- Electric ignition

First open the oven door, then turn the knob to the maximum temperature setting (

position). Then press the
thermostat knob to start the gas flow and the ignition spark. Wait about 10 seconds after the burner has been completely
lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation.

16

The ignition device should not be used for more than 15 seconds. If after that period the burner still has not
been lit, do not use the device and open the door of the room or wait at least 60 seconds before trying to light
the oven again.
WARNING: when trying to light the oven, the door must always be open.
The gas oven operation is indicated by a blue light
Verify that aspect flame of the oven burner be completely blue and with an aspect as indicated in figure
NOTICE: when using the oven for the first time it should be operated for 15-30 minutes at a temperature of
about 500°F/260°C without cooking anything inside in order to eliminate any moisture and odours from the
internal insulation.

During normal oven use, after lighting the burner and setting the desired temperature, wait about 15 minutes before
putting in any food to preheat the oven.
The oven is equipped with 4 guides at different heights level which can be used to insert shelves or the tray. To keep the
oven as clean as possible it is recommended to cook meat on the tray or on the shelf that has been inserted inside the
tray. The table below lists the general cooking times and the position of the tray for different types of foods. Personal
experience will help to determine any variations in the values reported in the table. In any case, it is recommended to
follow the instructions of the specific recipe being used.

This type of oven is equipped with a fan. The fan convection creates forced-air circulation in the horizontal direction.
Thanks to this type of operation, the ventilated oven can be used for different types of cooking at the same time, without
changing the taste of each food. Hot-air circulation guarantees a uniform distribution of heat. Pre-heating the oven is not
necessary, but for very delicate pastries, it is recommended to heat the oven before inserting the trays.
The convection system partially changes the various notions about traditional cooking. Meat no longer needs to be
turned while it is cooking and the rotisserie is no longer needed to cook a roast on the spit. Just put the meat directly on
the shelf.

GAS OVEN COOKING TABLE

MEAT
PORK ROAST 430/220 4 60-70
BEEF ROAST (YOUNG STEER) 480/250 4 50-60
BEEF ROAST 465/240 4 60-70
VEAL ROAST 430/220 4 60-70
LAMB ROAST 430/220 4 45-55
ROAST BEEF 445/230 4 55-65
ROAST HARE 450/235 4 40-50
ROAST RABBIT 430/220 4 50-60
ROAST TURKEY 450/235 4 50-60
ROAST GOOSE 450/225 4 60-70
ROAST DUCK 450/235 4 45-60
ROAST CHICKEN 450/235 4 40-45

FISH

PASTRY

FRUIT PIE 390/200 3 35-40
TEA CAKE 375/190 3 50-55
BRIOCHES 345/175 3 25-30
SPONGE CAKE 450/235 3 20
RING CAKE 375/190 3 30-40
SWEET PUFF PASTRIES 430/220 3 20
RAISIN LOAF 430/220 3 15-20
STRUDEL 355/180 3 15-20
SAVOIA COOKIES 375/190 3 15
APPLE FRITTERS 430/220 3 20
SAZOIARDI SANDWICH 430/220 3 20-30
TOAST SANDWICH 480/250 4 5
BREAD 430/220 3 30
PIZZA 430/220 3 20

TEMP °F/ °C HEIGHT MINUTES

390-440/200-225 3 15-25

17

To activate the convection fan use the selector placed on control panel.

Turn the knob anti clockwise for activation of the convection fan +light
Turn the knob clockwise to turn on the oven light.

CONVECTION GAS OVEN COOKING TABLE

MEAT
PORK ROAST 320-340/160-170 3 70-100
BEEF ROAST (YOUNG STEER) 340-355/170-180 3 65-90
BEEF ROAST 340-375/170-190 3 40-60
VEAL ROAST 320-355/160-180 3 65-90
LAMB ROAST 285-320/140-160 3 100-130
ROAST BEEF 355-375/180-190 3 40-45
ROAST HARE 340-355/170-180 3 30-40
ROAST RABBIT 320-340/160-170 3 80-100
ROAST TURKEY 320-340/160-170 3 160-240
ROAST GOOSE 320-355/160-180 3 120-160
ROAST DUCK 340-355/170-180 3 100-160
ROAST CHICKEN 355/180 3 70-90

FISH
PASTRY

FRUIT PIE 355-390/180-200 3 40-50
TEA CAKE 390-430/200-220 3 40-45
BRIOCHES 340-355/170-180 3 40-60
SPONGE CAKE 390-445/200-230 3 25-35
RING CAKE 320-355/160-180 3 35-45
SWEET PUFF PASTRIES 355-390/180-200 3 20-30
RAISIN LOAF 445-480/230-250 3 30-40
STRUDEL 320/160 3 25-35
SAVOIA COOKIES 300-355/150-180 3 50-60
APPLE FRITTERS 355-390/180-200 3 18-25
SAZOIARDI SANDWICH 340-355/170-180 3 30-40
TOAST SANDWICH 445-480/230-250 4 7
BREAD 390-430/200-220 4 40
PIZZA 390-430/200-220 3 20

TEMP °F/ °C HEIGHT MINUTES

320-355/160-180 3 / 4

USING THE GAS BROILER

The gas broiler is controlled with the same gas oven knob, but turning it clockwise instead of counterclockwise (see the
gas oven use instructions), matching the symbol with the indicator. The broiler burner always operates at maximum and
therefore there is no minimum position. In addition, it is equipped with a safety device to prevent the flame from going
out.

- Electric ignition: Cpmpletely open the oven door, then turn the knob to the broiler position setting (

position). Then
press the thermostat knob to start the gas flow and the ignition spark. Wait about 10 seconds after the burner has been
completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation.

ATTENTION: To use broiler please utilize the proper broiler grid installed inside the grid enamelled tray supplied
with the appliance; broiler tray shall be supported by oven grid.
WARNING: As with the oven, the broiler must be lit with the door completely open.

The gas broiler can be used to broil foods on the oven shelf .
The gas broiler operation is indicated by a blue light

IMPORTANT: when broiling food keep the door closed..
Verify that aspect flame of the broiler burner be completely blue and with an aspect as indicated in figure

18

Note: The use of a gas cooking appliance produces heat and humidity in the room where it is installed. Therefore, proper
ventilation in the room is needed and natural ventilation openings must remain unobstructed and activating the
mechanical exhaust fan/range hood. Intensive and continuous use of the appliance may require additional ventilation, for
example by opening a window, or increasing the power of the mechanical exhaust fan/range hood, if installed.

Note: the cooker is equipped with cooling fan

air frow come outside from the space existing between control and panel oven door avoiding the overheating
of their external surfaces during oven/broiler use.

starting each time gas oven/broiler are in operation. The cooling

CLEANING THE APPLIANCE:

Never use abrasive cleaners

Before cleaning the appliance it should be disconnected from the power supply.

Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using
warm water.

Any spillage must always be removed as soon as possible using a rag.
If it become difficult to open or close a valve, do not force it, but immediately request the assistance of the
technical service personnel.

Cleaning the enamelled parts: Enamelled parts should be cleaned frequently with soapy water. Never use abrasive

powder. Do not leave acidi or alkaline substances on the enamelled parts (such as vinegar, lemon juice, salt, tomato
sauce, etc.) and do not wash the enamelled parts while they are still hot.

Cleaning the stainless steel parts: Clean the parts with soapy water and dry them with a soft cloth. The shine is
maintained by periodically using specific stainless steel cream cleaner. Never use abrasive powders. Use specific
stainless steel cream cleaner to eliminate the glue remains afther the elimination of the blue plastic protection film on the
worktop after installation.

Cleaning the burner caps: Lift the burner caps from the burner heads and wash them in soapy water and dry
thoroughly. Before replacement on the burner head ensure that the holes are not clogged.

Cleaning the inner glass door: Clean the glass with warm soapy water using a sponge. A spatula can be used to
remove burner fat if used gently.

ATTENTION: while cleaning the door make sure to avoid any spillage in the venting holes on the top part of the door. To
clean inside the door it is necessary to disassemble the door through a service engineer.

ATTENTION: for further details about cleaning of the appliance, please contact your applliance retailer.

AFTER SALE SERVICE:

Please note here below details for after save service.

Refer to warranty certificate for warranty condiftions

Dealer /Importer: Name, address, phone

SERVICE CENTERS

Name Phone

MANUFACTURER:

BERTAZZONI SPA

VIA PALAZZINA, 8 – 42016 – GUASTALLA (REGGIO E.) ITALY
Tel. [phone] – telefax 0522/226440 – http://www.bertazzoni-italia.com

19

SPARE PART LIST

NUMBER COMPONENT DESCRIPTION

11 202387 BURNERS FLASK 1
18 202432 PART FOR DUAL WOK AND SEMI RAPID BURNERS 1
38 306003 THERMOSTAT CLIP 2
55 404213 WORKTOP FRONTGUARD 1
80 504160 COVER FOR SMALL FLAME SPREADER 1
81 504161 COVER FOR MEDIUM BURNER 1
82 504162 COVER FOR RAPID BURNER 1
85 504187 COVER IN FOR DUAL BURNER FLAME SPREADER 1

86 504186 COVER OUT FOR DUAL BURNER FLAME SPREADER 1
105 202450 UP SUPPORT FOR AXIAL COOLIN FAN 1
106 202439 DOWN SUPPORT FOR AXIAL COOLIN FAN 1
109 202436 INSIDE FLAP DOOR 1
117 101387 PROTECTION FOR FAN ASSISTED OVEN 1
120 101048 BLACK OVEN DRIP TRAY 1
138 202440 DISHWARMER BOTTOM 1
160 202262 BRIDLE FOR FIXING GAS VALVES 1
205 410571 PROFILE FOR GLASS DOOR 1
206 410572 PROFILE FOR GLASS DOOR 1
207 308034 BUMPER 2
274 202444 CROSS MEMBER 1
311 309010 RING FOR GRID SUPPORT 4
329 309141 INSIDE DOOR SPACER 2
385 306024 SPRING FOR SPARK PLUG 5
424 415071 SPARK PLUG FOR DUAL BURNER 2
425 415054 SPARK PLUG 350MM 3
427 415084 SPARK PLUG FOR OVEN 1
429 415077 SPARK PLUG FOR GRILL 1
430 415064 ACCUMULATOR 4U 2
441 404187 RIGHT GRID FOR OVEN 1
442 404212 SHELF OVEN 2
443 404497 GRID FOR TRAY 1
444 202407 FLASK HINGE 2
446 405077 OVEN DOOR HINGE 2
447 404188 LEFT GRID FOR OVEN 1
473 404117 SIMMER PLATE 1
478 410604 FLAP DOOR 1
478 125055 FLAP DOOR BURGUNDY RED 1
478 125049 FLAP DOOR BLACK 1
478 125041 FLAP DOOR RED 1
478 125053 FLAP DOOR PURE WHITE 1
544 504775 OVEN BURNER + SPARK PLUG + THERMOC. 1
546 505013 SUPPORT FOR GRILL BURNER NOZZLE 1
561 508025 TERMOCOUPLE MM300 1
562 508021 TERMOCOUPLE MM600 2
564 508036 THERMOCOUPLE OVEN BURNER 1
566 508034 TERMOCOUPLE ULTRA-RAPID BURNER 2
567 508026 THERMOCOUPLE GRILL BURNER 1
611 603020 OVEN CONVECTION FAN 1
612 603019 COOLING FAN 1
620 602039 COMMUTATOR 1
623 608046 OVEN BULB WITH HOLDER 2
648 601991 TERMINAL SEPARATOR 1
649 608047 SMALL WARNING LIGHT 1
649 608047 SMALL WARNING LIGHT 1
667 503121 THERMOSTAT 1
670 504128 SMALL FLAME SPREADER 1
671 504129 MEDIUM FLAME SPREADER 1
672 504130 RAPID FLAME SPREADER 1
675 504189 ULTRA RAPID FLAME SPREADER 1
702 408058 ADAPTER FOR WOK BURNER PAN SUPPORT 1
715 604070 DASYCHAIN SWITCH 1
760 510507 SMALL BURNER 1
761 510508 SEMI RAPID BURNER 1
762 510509 RAPID BURNER 1
764 510511 DUAL BURNER 1
881 502148 GAS VALVE BY PASS 036 SEMI-RAPID 1
883 502150 GAS VALVE BY PASS 065 DUAL OUTER 1
884 502179 GAS VALVE BY PASS 029 SMALL/DUAL INNER 2

X304GGVX

X304GGVI

X304GGVNE

X304GGVRO

X304GGVBI

886 502180 GAS VALVE BY PASS 047 RAPID 1
917 200327 STAINLESS STEEL SIDE 2
917 125003 SIDE BURGUNDY RED 2
917 125027 SIDE BLACK 2
917 125033 SIDE RED 2
917 125045 SIDE PURE WHITE 2
929 202389 RIGHT VERTICAL VENT 1
930 202214 FEET SUPPORT 2
940 201168 FIXING FOR WORK TABLE 2
943 308035 BUMPER FOR PAN SUPPORT 12
947 403343 HANDLE TERMINAL 2
964 408068 CAST IRON PAN SUPPORT 1
965 408063 CAST IRON PAN SUPPORT 2 BURNERS 2
972 202360 WORK TABLE FIXING 4

1041 401904 GAS VALVE KNOB 3
1043 401905 GAS THERMOSTAT KNOB 1
1044 401906 ELECTRIC KNOB 1
1046 401961 DUAL IN KNOB 1
1047 401962 DUAL OUT KNOB 1
1143 910711 UPSTAND KIT 1
1406 403435 OVEN DOOR HANDLE 1
1407 406396 OVEN DOOR GLASS 2
1411 411093 GASKET FOR OVEN FRONT 3 SIDE 1
1415 602042 THERMOSWITCH 1
1419 411094 GASKET FOR OVEN FRONT 1 SIDE 2
1421 406395 INNER OVEN GLASS 1
1508 410605 STAINLESS STEEL OVEN DOOR 1
1508 125056 OVEN DOOR BURGUNDY RED 1
1508 125050 OVEN DOOR BLACK 1
1508 125052 OVEN DOOR RED 1
1508 125054 OVEN DOOR PURE WHITE 1
1602 210577 CONTROL PANEL 1
1603 309119 BRIDLE FOR FIXING GAS VALVES/THERMOSTAT 1
1608 501761 ALL.TUBE FOR OVEN BURNER 1
1609 505056 SUPPORT FOR OVEN BURNER NOZZLE 1
1614 201173 BACK PANEL 1
1615 202435 CONTROL SUPPORT 1
1617 608045 SMALL BLUE BUD 1
1622 608025 SMALL RED BUD 1
1624 200348 WORK TABLE 1
1627 501755 GAS COLLECTOR 1
1628 501759 TUBE FOR RIGHT FRONT BURNER 1
1631 501760 TUBE FOR RIGHT BACK BURNER 1
1639 202390 LEFT VERTICAL VENT 1
1644 414048 S.STEEL LEG 4
1645 414031 BASE FOR LEGS 4
1646 501762 GRILL THERMOSTAT TUBE 1
1685 201166 REAR VENT STACK 2
1686 201167 FRONT VENT STACK 2
1687 202443 BACK ENCLOSURE METAL PANEL 1
1705 410606 OVEN GLASS SUPPORT 1
1801 501758 TUBE FOR LEFT BACK BURNER 1
1803 501756 TUBE FOR EXTERNAL DUAL BURNER 1
1804 501757 TUBE FOR INTERNAL DUAL BURNER 1
2016 101383 OVEN SIDE PANEL BLACK RIGHT 1
2017 101384 OVEN SIDE PANEL BLACK LEFT 1
2031 101408 UPPER PART FOR BODY 1
2032 101385 BACK OVEN BODY 1
2057 101389 FRONT PANEL MUFFLE 1
2097 101388 OVEN BOTTOM PANEL BLACK 1
2098 202437 OVEN BURNER BASE 1
2099 202497 OVEN BASE 1
4106 405078 HINGE FOR FLAP DOOR 2
4301 200328 RIGHT SIDE PROFILE 1
4301 125002 RIGHT SIDE PROFILE BURGUNDY RED 1
4301 125026 RIGHT SIDE PROFILE BLACK 1
4301 125032 RIGHT SIDE PROFILE RED 1
4301 125044 RIGHT SIDE PROFILE PURE WHITE 1
4302 200329 LEFT SIDE PROFILE 1
4302 125001 LEFT SIDE PROFILE BURGUNDY RED 1
4302 125025 LEFT SIDE PROFILE BLACK 1
4302 125031 LEFT SIDE PROFILE RED 1
4302 125043 LEFT SIDE PROFILE PURE WHITE 1
5140 504776 GRILL BURNER 1