Berbel BLB 60 FL, BLB 90 FLE, BLB 90 FL, BLB 60 FLE Operating And Installation Instructions

berbel-

Fan Module BLB

Operating and installation instructions for the models:

BLB 60 FL / BLB 90 FL

BLB 60 FLE / BLB 90 FLE

01/2011 (updated 08/2015)

English translation of the German original manual

This manual helps you to use and install our product

as intended, safely and economically.

In the following text, our product the berbel-

Lüfterbaustein BLB 60 FL, BLB 90 FL, BLB 60 FLE

and BLB 90 FLE will be referred to as the 'device' in

short.

This manual is intended for the following persons:

§ Persons using the device

§ Persons cleaning the device

§ Persons disposing of the device

§ Persons installing the device

Everyone in these groups of people must have read

and understood the contents of this manual. Other

persons should not be permitted to use the device

unsupervised (children or persons with impaired

mental or sensory abilities for example).

You can increase the reliability and service life of the

equipment and minimise risks by following the

instructions in this manual.

Layout features in the text

The text in this manual is laid out in a standard way.

This helps you to easily distinguish between the

various elements:

Normal text

Cross references

§ Lists or

Ø Action steps.

Tips contain special information to help you

use the device economically.

Design features in the illustrations

The illustrations consist of greyscale representations.

If elements are referred to in the text or in the legends,
these elements are marked with a position number 

Movements or actions to be carried out are indicated

by motion or direction arrows. If there are several steps

to be performed in sequence shown on one illustration,

the order is indicated by numbers (1., 2., etc.):

3

Most functions (operation, maintenance) and the assembly of all devices which are described in these

instructions are identical.

All the following descriptions and illustrations are therefore valid for the berbel- fan fodule

BLB 60 FL, BLB 60 FLE, BLB 90 FL and BLB 90 FLE.

The few exceptions to this are referred to directly in the text at the appropriate places.

The berbel-Lüfterbaustein BLB 90 FL is mainly shown in the illustrations.

Contents

Safety.....................................................................................................................................................................5

Proper and intended use............................................................................................................................................5

Ban on independent conversions and modifications..................................................................................................5

Layout of hazard notices.............................................................................................................................................5

Layout of notices regarding damage to property or the environment.........................................................................5

General safety instructions......................................................................................................................................6

Basic safety instructions.............................................................................................................................................6

Safety instructions for the user................................................................................................................................6

Safety instructions for the installer...........................................................................................................................7

Operating instructions...........................................................................................................................................10

Description for the user.........................................................................................................................................10

Possible operating modes........................................................................................................................................10

Device view with closed lower section......................................................................................................................11

Device view with opened lower section....................................................................................................................12

Operating.............................................................................................................................................................13

Turning on the ventilation function............................................................................................................................13

Changing the power level.........................................................................................................................................14

Turning off the ventilation function............................................................................................................................15

Turning the lighting on and off..................................................................................................................................16

Cleaning...............................................................................................................................................................17

Cleaning intervals.....................................................................................................................................................17

Cleaning with normal soiling.....................................................................................................................................17

Cleaning when heavily soiled...................................................................................................................................18

Cleaning the surfaces...............................................................................................................................................20

Cleaning the rotary knob...........................................................................................................................................21

Maintenance.........................................................................................................................................................22

Maintaining the device..............................................................................................................................................22

Changing the bulbs...................................................................................................................................................22

Changing the filter filling (hybrid and recirculated air filters).....................................................................................22

Troubleshooting....................................................................................................................................................25

4

Installation instructions..........................................................................................................................................27

Description for the installer....................................................................................................................................27

Possible operating modes........................................................................................................................................27

Information about extracted air mode.......................................................................................................................28

Basics about the device............................................................................................................................................33

Device view from above............................................................................................................................................34

Device view from underneath with a closed lower section.......................................................................................35

Device view from underneath with opened lower section........................................................................................36

Preparation for installation....................................................................................................................................37

Qualifications of personnel.......................................................................................................................................37

Prerequisites for the mechanical end assembly.......................................................................................................37

Brief overview of the installation...............................................................................................................................38

Tools and equipment needed...................................................................................................................................40

Unpacking.................................................................................................................................................................40

Check the delivery....................................................................................................................................................41

Remove the parts for installation..............................................................................................................................42

Remove the lower section........................................................................................................................................43

Remove the capillary trap.........................................................................................................................................43

Remove the bracket..................................................................................................................................................44

Create the installation cut-out...................................................................................................................................44

Installing the device..............................................................................................................................................45

Safety distances are observed.................................................................................................................................46

Fitting the bracket BLB 60 FL(E)..............................................................................................................................46

Fitting the bracket BLB 90 FL(E)..............................................................................................................................47

Hang the device........................................................................................................................................................48

Align the device horizontally.....................................................................................................................................49

Secure the lock.........................................................................................................................................................49

Only BLB 60 FLE / BLB 90 FLE: Connect the connection cable of the fan.............................................................50

Connecting the wall box and the window contact switch contacts...........................................................................51

Creating the exhaust air connection.........................................................................................................................54

Install the other parts................................................................................................................................................57

Connect the power supply........................................................................................................................................58

Initial cleaning.......................................................................................................................................................58

Cleaning the surfaces...............................................................................................................................................58

Cleaning the controls................................................................................................................................................58

Disassembling the device.....................................................................................................................................59

Disposal...............................................................................................................................................................60

Disposal of the packaging.........................................................................................................................................60

Gerät Disposal ..........................................................................................................................................................60

Technical specifications........................................................................................................................................61

Volume flow for operation with an external fan.........................................................................................................61

Fan module BLB 60..................................................................................................................................................61

Contact.................................................................................................................................................................62

Contacting the customer services of the manufacturer............................................................................................62

General safety instructions

Safety 5

Safety

Proper and intended use

The device can be used to extract cooking vapours

when cooking in private households.

Ø Only use this device in private kitchens.

This device has been exclusively intended for this

purpose and must only be put to this use. The device

may only be used in the manner described in this

manual.

Any other use of or modification to the device is

considered improper usage and may lead to damage.

The manufacturer is not liable for damages which

occur as a result of improper use, incorrect installation

or incorrect operation. This device is not intended for

commercial use.

Ban on independent conversions and
modifications

§ Do not undertake and independent modifications of

or conversions to the device. Conversions or

modifications without the approval of berbel

Ablufttechnik GmbH are not permitted.

§ Never bridge or bypass the protective equipment

found on the device.

Layout of hazard notices

In this manual you will find the following categories of

hazard notices:

DANGER

Notices with the word DANGER warn

of a hazardous situation which will

result in death or serious injuries.

WARNING

Notices with the word WARNING warn

of a hazardous situation which can

lead to death or serious injuries.

CAUTION

Notices with the word CAUTION warn

of a situation that can lead to minor or

moderate injuries.

Layout of notices regarding damage to
property or the environment

ATTENTION

These notices warn of a situation that

can lead to damage to property or to

the environment.

Safety

6 Safety

General safety instructions

Ø Read this chapter carefully before installing, using,

or cleaning the device.

Specific, important safety instructions can be

found:

- in the "Safety instructions for the installer" for

persons installing or removing the device.

- in the "Safety instructions for the user" for

persons operating or cleaning the device. Read

these chapters carefully to avoid danger, injuries

and damage.

Ø Follow the safety and danger notices during all

activities on the device.

Ø Make sure that only persons who have read and

understood the contents of this manual use the

device.

Children or other persons with impaired mental or

sensory abilities should not be permitted to use the

device unsupervised.

Ø Include this manual if you pass the device on.

Basic safety instructions

This section contains the basic safety instructions for

handling the device. Additional safety instructions,

concerning the particular actions and processes, can

be found in the respective chapters.

§ Take note of all safety instructions and danger

notices in this manual.

§ Check the device and all its parts for visible

damage. In the event of damage, contact your

dealer or berbel customer service. You may only

use the device if it is in perfect working order.

§ Always let qualified specialist personnel conduct

maintenance or repair work. Otherwise, you

endanger yourself and others.

§ Only use this device in private kitchens.

§ Use this device only when the capillary trap is fitted

and with the lower section closed.

§ Make sure that there are no unsupervised children

in the vicinity of the device and that they do not play

with it.

Safety instructions for the user

Read this chapter carefully before using or cleaning the

device.

Ø Follow the warning notices during all activities on

the device.

Avoiding dangers caused by electric shock

§ Do not use the device with a damaged electrical

connection cable.

§ The mains plug must be easily accessible so that

you can quickly and easily isolate the device from

the mains supply in the event of an emergency. If

the mains plug is inaccessible following installation,

an all-pole isolating device with a contact gap of at

least 3 mm must be installed and accessible.

§ In the event of a malfunction, disconnect the device

immediately from the mains. Only allow trained

specialist personnel to repair the device.

§ Do not kink or crush the mains cable.

§ Only use the device if it is connected and fused in

accordance with the technical data.

§ Never open the housing of the device's fan unit.

§ Keep the device dry.

§ Avoid exposing the device to dripping or splashing

water or other fluids.

§ Do not place any objects filled with fluids, like vases

for example, above the device or on the device.

If fluid does enter the device:

- Immediately shut off the power supply

by removing the fuse, for example. -

Make sure that the power supply

of the device cannot be unintentionally

reconnected. Perhaps by designating a person to

prevent the fuse being switched on again.

- Allow the device to dry.

- Have the device checked and repaired by trained,

specialist personnel prior to using the device

again.

Safety instructions for the

installer

Safety 7

Avoiding the risk of explosion

§ Do not operate the device in an environment with a

risk of explosion.

Avoiding the risk of fire

§ Do not use the device during a fire or when there is

an imminent danger of fire (e.g. a smell of gas) in

the household.

§ Make sure that the hob has cooled down before you

cover it.

A dirty device can cause fire hazards.

§ Keep the device in perfect working order and check

it regularly.

§ Regularly remove any grease residues which are

present. Grease residues pose a fire hazard.

Overheated oil and a naked flame can cause fire

hazards.

§ Do not flambé underneath the device. Naked flames

can cause damage to neighbouring cabinets for

example.

§ Never deep-fry food unattended under the device.

Overheated oil can spontaneously ignite.

When operating over a gas stove or a gas unit:

§ Make sure that the gas flame is kept low. Naked

flames should not appear beyond the edge of the

pan base.

In recirculated air mode:

§ A covered or sealed ventilation outlet can cause a

fire hazard. Do not place any objects like lids or

plates for example on or in front of the ventilation

slits of the device. In the case of recirculated air

devices, out flowing air must be able to escape

back into the kitchen through the ventilation slits

without impediment.

§ No objects should be mounted in the area of the

ventilation slits of the device which could impede

the air flow. Make sure that out flowing air is able to

flow into the kitchen without impediment.

Operating over a solid-fuel burning fireplace:

The device may only be used over a fireplace for solid

fuels (e.g. a coal-burning stove) if:

§ the fireplace has a sealed cover which cannot be

removed. Otherwise there is an increased fire risk

due to flying sparks.

§ the legal and country-specific regulations are

observed.

Avoiding risks of injury

§ To prevent the risk of falling, use a stable step-

ladder for all work on the device, for example

replacing the filter and cleaning the device.

§ To prevent the risk of injury by falling parts, do not

place any objects on the device.

Avoiding the risk of suffocation

If the device and an open fireplace which uses air from

the room for its oxygen supply, gases or waste gases

may be drawn into the room.

§ Ensure there is an adequate supply of fresh air into

the dwelling.

§ Never let children play with the foil or other parts of

the packaging.

§ Store the film or other parts of the packaging in a

location which is inaccessible to children.

§ Make sure that all of the permits required for

operation in your country have been obtained (e.g.

the master chimney sweep).

§ Make sure that all standards and guidelines for

operating the device in your country are observed.

Avoiding environmental damage

§ Dispose of the device and its accessories in

accordance with the legal regulations.

Safety instructions for the installer

The safety instructions concerning the device's

installation can be found in this section. Additional

safety instructions, concerning the particular actions

Safety

8 Safety

and processes, can be found in the respective

chapters.

Ø Read this chapter carefully before installing the

device.

Ø Follow all the safety and danger notices during all

activities on the device.

Ø Only install this device in private kitchens.

Ø Make sure that the power cable is free from voltage

during installation.

Ø Check the device and all its parts for visible

damage. In the event of damage, contact your

dealer or berbel customer service. You may only

install the device if it is in perfect working order.

Ø Mount the device using the supplied brackets only

on load bearing building parts (solid construction).

Ø Use appropriate fastening mechanisms for any

other sort of installation. If in doubt, please check

with the dealer. Otherwise, you endanger yourself

and others.

Ø Always let qualified specialist personnel conduct

repair work. Otherwise, you endanger yourself and

others.

Avoiding dangers caused by electric shock

§ Only let trained, qualified electricians work on the

power supply.

The electricians must have the following knowledge

and abilities as a minimum:

§ Basic knowledge of electrical engineering

§ Knowledge of country-specific regulations

and standards (e.g. in Germany,

DIN 57100/VDE 0100, part 701)

§ Knowledge of the applicable

safety regulations

§ Knowledge of the applicable legal

regulations for gas installations (e.g.

in Germany the technical rules for gas

installations TRGI).

§ Only install the device if it is connected and fused in

accordance with the technical data.

§ Do not kink or crush the mains cable.

§ Do not use the device with a damaged electrical

connection cable.

§ In the event of a malfunction, disconnect the device

immediately from the mains.

§ The mains plug must be easily accessible so that

you can quickly and easily isolate the device from

the mains supply in the event of an emergency. If

the mains plug is inaccessible following installation,

an all-pole isolating device with a contact gap of at

least 3 mm must be installed and accessible.

§ If the device is moved from a cold environment into

a hot one, condensation may form inside the

device. In this case wait about 2 to 3 hours before

bringing the device into service.

§ Avoid exposing the device to liquids.

§ Keep the device dry.

Avoiding the risk of explosion

§ Do not install the device in an environment with a

risk of explosion.

Avoiding the risk of fire

§ Make sure that the hob has cooled down before you

cover it.

In recirculated air mode:

§ A covered or sealed ventilation outlet can cause a

fire hazard. In the case of recirculated air devices,

out flowing air must be able to escape back into the

kitchen through the ventilation slits without

impediment.

§ You may not install any objects that could impede

the airflow. Make sure that out flowing air is able to

flow into the kitchen without impediment.

Safety instructions for the

installer

Safety 9

The device may only be installed over a fireplace for

solid fuels (e.g. a coal-burning stove) if:

§ the fireplace has a sealed cover which cannot be

removed. Otherwise there is an increased fire risk

due to flying sparks.

§ the legal and country-specific regulations are

observed.

Avoiding risks of injury

§ To prevent the risk of falling, use a stable

stepladder for all work on the device, for example

replacing the filter, installing and cleaning the

device.

§ To prevent the risk of injury by falling parts, do not

place any objects on the device.

§ To prevent injury from falling parts, only use

suitable fastening materials.

§ To prevent cuts from broken glass, use suitable

protective gloves.

Avoiding the risk of suffocation

If the device and an open fireplace which uses air from

the room for its oxygen supply, gases or waste gases

may be drawn into the room.

§ Make sure that all of the permits required for

operation in your country have been obtained (e.g.

the master chimney sweep).

§ Make sure that all standards and guidelines for

operating the device in your country are observed.

§ Ensure there is an adequate supply of fresh air into

the dwelling.

§ Never let children play with the foil or other parts of

the packaging.

§ Store the film or other parts of the packaging in a

location which is inaccessible to children.

Minimising the danger of collapse

In extracted air mode:

§ The wall breakthrough that is needed must be

created by technically qualified persons. Wall

breakthroughs affect the building's structural

stability. Improperly made wall breakthroughs could

result in the building collapsing.

Operating instructions

10 Operating instructions

Operating instructions

Description for the user

The following illustrations show the way the

possible operating modes work. The devices

used are shown as symbols. The illustrations are

meant to serve as a guide. The illustrated device

shapes may differ from your device.

With this device you can suck in and clean cooking

vapours. Cleaning the room air that is sucked in is

done in several cleaning stages. Dirt particles, such as

fat and oil particles, are trapped on the upper and lower

sections.

Possible operating modes

The device can work in different operating modes:

§ Recirculated air mode

§ Extracted air mode

§ Hybrid mode

The individual operating modes are described in the

next sections.

Extracted air mode

The device draws room air in and filters dirt particles

out of the air. The cleaned air is discharged outside.

Recirculated air mode

The filter filling must be replaced at regular

intervals in recirculated air mode.

The device draws room air in and filters dirt particles

out of the air.

The filter filling in the recirculated air filter neutralises

any smelly odours present. The odour-free, cleaned

room air is fed back into the room.

Hybrid mode

The filter filling must be replaced regular intervals

in hybrid mode.

The device draws room air in and filters dirt particles

out of the air. Part of the cleaned air is discharged

outside. The filter filling in the hybrid filter neutralises

the existing odour components of the remaining air

sucked in from the room. The odourless, cleaned room

air is then fed back into the room.

Description for the

user

Operating instructions 11

Device view with closed lower section





fan module BLB 90 FL  Rotary knob (on and off switch)



Lower section  Illumination

All the following descriptions and illustrations are therefore valid for the berbel- fan module

BLB 60 FL, BLB 60 FLE, BLB 90 FL and BLB 90 FLE.

The berbel- fan module BLB 90 FL is mainly shown in the illustrations.

Description for the user

12 Operating instructions

Device view with opened lower section





fan module BLB 90 FL  Capillary trap



Upper section  Lower section

All the following descriptions and illustrations are therefore valid for the berbel- fan module

BLB 60 FL, BLB 60 FLE, BLB 90 FL and BLB 90 FLE.

The berbel- fan module BLB 90 FL is mainly shown in the illustrations.

Operating

Operating instructions 13

Operating

WARNING

Suffocation risk due to low oxygen

levels when operating the device.

Ø Ensure there is an adequate supply

of fresh air into the dwelling.

Ø Make sure that the device is

connected to a window contact

switch for safe operation.

Ø Make sure that all country-specific

statutory regulations are observed

(e.g. in Germany the requirements of

the federal state's fire regulations).

The functions of the device are controlled using the

control panel. This device is fitted with a rotary knob

(ThinCoder) for operation.

The rotary knob is located on the bottom side of the

device.

You can find out how to operate all the device functions

using this rotary knob in the following sections.

Turning on the ventilation function

WARNING

Explosion risk and fire hazard from gas

or explosive or flammable gas mixtures

in the kitchen when operating electrical

equipment.

If you smell gas or there is a suspicion

of flammable gas:

Ø Do not operate or switch on any

electrical equipment.

Ø Ensure there is an adequate supply

of fresh air into the dwelling.

Ø Leave the building.

Ø Call the fire brigade.

WARNING

Risk of burns from flambéing, naked

flames or overheated fat/oil under the

device.

Naked flames can cause burns, e.g. to

the skin.

Ø Always keep naked flames small

(e.g. with a gas cooker). The gas

flame should not extend beyond the

base of the pan.

Ø Prepare foods using fats or oils only

under supervision.

Ø Do not flambé underneath the

device.

Operating

14 Operating instructions

ATTENTION

Risk of fire due to flambéing or

overheated oil and fat under the

device.

Naked flames can cause damage to

neighbouring cabinets and objects for

example.

Ø Never leave deep fat fryers

unattended during use.

Ø Do not flambé underneath the

device.

The following tip only applies for recirculated air mode.

Ø If you turn the device on and notice unpleasant

odours, then you should replace the filter's

filling.

See Cleaning starting at page 17.

If you turn on the device and notice that the fan noise

has increased, you should clean the device.

See Cleaning starting at page 17.

After six hours of continuous operation the device

automatically switches off the ventilation mode.

Ø If required, turn the device on again.

To remove cooking vapours best:

Ø Turn the device on when you start cooking.

Ø If you are frying, turn the device to its highest

power setting.

Use the run-on function in hybrid and

recirculated air modes so that the filter used

(BHF or BUF) is dried after the actual cooking

process. This prevents smells developing and

ensures it reaches its maximum service life.

You can operate the device in four different power

levels.

To turn the device on, proceed as follows:

Ø Turn the rotary knob clockwise from level "0" to the

desired power level.

The rotary knob snaps into each power level.

The device operates immediately at the selected power

level.

Changing the power level

During operation, you can set a different power level at

any time.

Ø Turn the rotary knob from the current position to

the position of the desired power level.

The rotary knob snaps into each power level.

The device operates at the selected power level.

After six hours of continuous operation the device

automatically switches off the ventilation mode.

Ø If required, turn the device on again.

Operating

Operating instructions 15

Turning off the ventilation function

To turn off the ventilation function, proceed as follows:

Ø Turn the rotary knob anti-clockwise to the "0"

position.

The rotary knob snaps into each power level.

The device turns off the ventilation function.

Operating

16 Operating instructions

Turning the lighting on and off

The device is fitted with an energy saving LED light to

light up the hob.

The lighting can be used independently from the fan.

Turn the lighting on

To turn on the lighting, proceed as follows:

Ø Press on the rotary knob with a finger.

The lighting is switched on.

Turn the lighting off

To turn off the lighting, proceed as follows:

Ø Press on the rotary knob with a finger.

The lighting is switched off.

Cleaning

Operating instructions 17

Cleaning

DANGER

Fatal electrical shocks through liquids

that get into the device.

Ø Never spill liquids into the device.

Ø Ensure that fluids never get into the

device.

WARNING

Risk of fire from grease residues in

and on the device.

Ø You should regularly clean the

device.

ATTENTION

Damage to the surfaces from sharp

objects or abrasive cleaning agents.

Ø Never use sharp objects, abrasive or

aggressive cleaning agents.

Ø Use a soft, damp cloth.

Cleaning intervals

Usage Time interval

Little or

occasional

use.

After each cooking session.

See Cleaning with normal soiling on

page 17.

Daily or

heavy

use.

At least every three weeks.

See Cleaning when heavily soiled on

page 18.

Cleaning with normal soiling

The device is designed to capture foreign particles

from the room air that is sucked in and to collect them

in a grease tray.

Proceed as follows to clean the device at normal

soiling levels:

Ø Turn off the device.

Ø Open the lower section by pulling the rounded

edge on the front side downwards.

Ø Use a soft, damp cloth or kitchen paper towels for

cleaning.

Ø Wipe off the upper and lower sections.

Close the lower section.

Ø Close the lower section by pushing it upwards until

the two magnetic fasteners can be heard to click

together.

Cleaning

18 Operating instructions

Cleaning when heavily soiled

If the device is heavily soiled, you must remove the

lower section and the capillary trap. These can be

easily removed and refitted, and they can be reused

after they have been cleaned.

Proceed as follows to clean the device at heavy soiling

levels:

Remove the lower section

Ø Turn off the device.

Ø Open the lower section by putting the rounded

edge downwards.

Ø Use a soft, damp cloth or kitchen paper towels for

cleaning.

Ø Wipe off the upper and lower sections.

Ø Grasp the lower section on its sides with both

hands when it is hanging down perpendicularly.

Ø Lift the lower section about 2 cm (1.).

Ø Release the lower section by pulling it forwards

(2.).

Ø Remove the lower section.

Cleaning

Operating instructions 19

Remove the capillary trap

Ø Grasp the sides of the capillary trap with both

hands.

Ø Pull the capillary trap downwards.

Clean the parts

ATTENTION

Damage to the lower section by

improper cleaning.

Ø Clean the lower section e.g. with a

damp cloth.

Ø Clean the lower section e.g. with a damp cloth.

Ø Clean the upper section e.g. with a damp cloth.

Ø Clean the capillary trap e.g. in the dish washer.

Ø Clean the four surfaces of the recess for the

capillary trap e.g. with a damp cloth.

Ø Clean the two edges above the recess for the

capillary trap e.g. with a damp cloth.

After cleaning replace the cleaned and dry parts as

follows:

Insert the capillary trap

Ø Make sure that the capillary trap is completely dry

before re-inserting.

Ø Insert the capillary trap into the device by pressing

it firmly upwards with both hands.

The capillary trap snaps into place.

Cleaning

20 Operating instructions

Reassemble the lower section.

Ø Grip the lower section with both hands.

Ø Insert the lower section into the device from below

until the guide grooves of the lower section are in

front of the device guide pins at the same time.

Ø Press the lower section rearwards into the device

(1.).

Ø Pull the lower section downwards (2.) until it clicks

into place.

Ø Make sure that the lower section is fitted correctly.

The lower section is fitted correctly when you can

move it easily.

Close the lower section.

Ø Close the lower section by pushing it upwards until

the two magnetic fasteners can be heard to click

together.

Cleaning the surfaces

ATTENTION

Damage to the surfaces from sharp

objects or abrasive cleaning agents.

Ø Never use sharp objects, abrasive or

aggressive cleaning agents.

Ø Use a soft, damp cloth.

Clean the surfaces with a soft, damp cloth and a mild

household cleaner.

Cleaning

Operating instructions 21

Cleaning the rotary knob

The rotary knob (ThinCoder) is fitted to the device on

one axis. This axis has been milled off on one side. A

matching opening is found as a counterpart on the

underside of the rotary knob. The rotary knob can only

be attached if the milled sides are turned so they match

each other.

Removing the rotary knob

Ø Pull off the rotary knob.

Cleaning the rotary knob

Ø Clean the rotary knob in the dishwasher or using a

damp cloth.

Fitting the rotary knob

ATTENTION

Damage to the rotary knob through

misalignment.

Ø Turn the rotary knob around to the

correct installation position.

Ø Install the rotary knob by pushing it upwards (1)

when it is in the correct installation position.

Maintenance

22 Operating instructions

Maintenance

Maintaining the device

The device is maintenance-free.

Changing the bulbs

The device is fitted with LED lighting. The bulbs have a

service life of approximately 50,000 operating hours.

Ø If you have any problems, contact your berbel

dealer or customer services.

Changing the filter filling (hybrid and
recirculated air filters)

Replace the filter filling in accordance with the following

table:

Usage Time interval

Little or

occasional

use

At least every 24 months or when there

are odours in the exhaust air.

Daily or

heavy use

At least every 12 months or when there

are odours in the exhaust air.

WARNING

Risk of falling when changing the filter

or during work carried out at height.

Ø Use a stable step-ladder.

WARNING

Risk of injury from hot parts.

Ø Ensure that the cooking hob and the

device have cooled down.

Ø Let all parts cool down before

beginning work.

WARNING

Risk of injury from falling parts.

Ø Ensure that no-one is beneath the

working area when working on the

device.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

The filter must be easily accessible.

Ø Remove all the screens and other attached

modifications. The filter must be easily accessible.

The filter is easily accessible.

Maintenance

Operating instructions 23

Removing the hybrid filter

To change the filter filling, proceed as follows:

Ø Remove the exhaust pipe from the socket.

Ø Remove the socket from the filter.

Ø Remove the exhaust pipe from the hybrid filter.

Ø Lift the filter at least 3 cm (1.).

Ø Remove the filter to the front (2.).

The filter is removed.

Remove the recirculation air filters.

To change the filter filling, proceed as follows:

Ø Lift the filter at least 3 cm (1.).

Ø Remove the filter to the front (2.).

The filter is removed.

Change the filter filling

The method for changing the filter's filling is

described separately in an instruction manual for

the filter filling.

Ø Change the filter's filling.

Maintenance

24 Operating instructions

Replace the filter

To make sure that the filter is installed correctly,

a guide is installed on the filter seating.

Ø Insert the filter into the device from the top.

The filter is inserted correctly when the bottom edge of

the filter is parallel to the top edge of the fan's housing

and the gap is approximately 5 mm wide.

Ø Make sure that the filter is inserted correctly.

If the filter is not correctly fitted, proceed as follows:

Ø Remove the filter.

Ø Replace the filter again.

Only in hybrid operation:

Ø Push the exhaust pipe onto the filter collar.

Ø Seal the transition between the exhaust pipe and

the guide with the help of sealing tape.

Ø Ensure that the exhaust pipe is correctly fitted.

Ø Fit the screens or other attached modifications.

The filter filling has been exchanged.

Troubleshooting

Operating instructions 25

Troubleshooting

DANGER

Fatal electric shock due to improperly

carried out repairs.

Ø Ensure that all repairs are carried out

by the manufacturer or by

authorised, specialised personnel.

Fault Possible cause Remedy

No power supply. Check that the all-pole mains switch is

turned on.

Switch the mains switch on.

Fan and lighting do not

work.

The fuse may have been tripped or is

defective.

Check to see if the fuse has tripped.

When you use electric circuit breakers, turn

the circuit breaker on again.

For other types of fuse, consult a qualified

electrician.

The extractor hood is not switched on. Check all possible power levels.

See Turning on the ventilation function on

page 13.

The fan does not work.

The extractor hood is connected to a

window contact switch and the window

is closed.

Open the window.

BLB 60 FLE/90 FLE:

External fan does not

function.

No power supply or connecting cable is

not plugged in or connected.

Please consult your berbel dealer.

The lighting does not

work.

The bulb has blown. Please consult your berbel dealer.

Smells occur during

operation.

The filter filling is used up. Change the filter filling.

See Changing the filter filling (hybrid and

recirculated air filters) on page 22.

Troubleshooting

26 Operating instructions

Fault Possible cause Remedy

The recirculated air filter is clogged. Replace the filter filling of the recirculated

air filter.

See Changing the filter filling (hybrid and

recirculated air filters) on page 22.

The hybrid filter is blocked. Replace the filter filling of the hybrid filter.

See Changing the filter filling (hybrid and

recirculated air filters) on page 22.

Poor device

performance.

The exhaust pipe was not properly

connected or installed.

Please consult your berbel dealer or berbel

customer services.

Ø If the fault persists, please contact your berbel

dealer or berbel customer services.

Installation instructions

Installation instructions 27

Installation instructions

Description for the installer

Possible operating modes

The following illustrations show the way the

possible operating modes work. The devices

used are shown as symbols. The illustrations are

meant to serve as a guide. The illustrated device

shapes may differ from your device.

The device can be fitted in different operating modes:

§ Recirculated air mode

§ Extracted air mode

§ Hybrid mode

Depending on the desired operating mode, the

installation of the device varies. The different

installations of the individual operating modes are

described in the following sections.

Ø Make sure that all safety instructions and

regulations are adhered to during installation.

Installation for recirculated air mode

In this installation a BUF recirculated air filter is fitted to

the device's fan outlet.

Ø Make sure that the cross-section of the ventilation

slits in the top structure is more than 300 cm².

Ø Make sure that the air can flow freely out of the

device.

Ø Ensure that you can change the filter filling at a

later date.

The filter's filling needs to be regularly replaced.

Installation for extracted air mode

Observe and follow the information concerning

the exhaust pipe in the Information about

extracted air mode chapter.

In this installation the exhaust pipe is fitted to the

device's fan outlet.

Ø Make sure that the exhaust pipe has a diameter of

at least 125 mm.

Ø Make sure that the air can flow freely out of the

device.

Installation instructions

28 Installation instructions

Installation for hybrid mode

In this installation a BHF hybrid filter is fitted to the

device's fan outlet. The exhaust pipe is connected to

the hybrid filter.

Ø Make sure that the cross-section of the ventilation

slits in the top structure is more than 200 cm².

Ø Make sure that the exhaust pipe has a diameter of

at least 125 mm.

Ø Make sure that the air can flow freely out of the

device.

Ø Ensure that you can change the filter filling at a

later date.

The filter's filling needs to be regularly replaced.

Information about extracted air mode

DANGER

Danger of suffocation due to lack of

oxygen when the device is operated at

the same time as there is an open fire.

Ø If the device is operated at the same

time as devices which work using

room air (e.g. gas stove, fire places

or gas heaters), no gases or exhaust

gases are drawn into the room.

Ø Ensure there is an adequate supply

of fresh air into the dwelling.

Ø Make sure that the legal provisions

of the fire regulations (FeuV in

Germany) applicable to your

location/federal state are observed.

Ø Make sure that you have obtained

the permit from your master chimney

sweep to operate the extractor hood,

if required.

Measures to ensure a sufficient supply of fresh air:

§ Operate the device only when a window contact

switch is fitted.

§ Open the window.

§ Open the door.

§ Install a berbel BMK wall box.

§ Ensure that the prescribed forced ventilation of the

open fire is working.

Installation instructions

Installation instructions 29

WARNING

Suffocation risk due to low oxygen

levels when operating the device.

Ø Ensure there is an adequate supply

of fresh air into the dwelling.

Ø Make sure that the device is

connected to a window contact

switch for safe operation.

Ø Make sure that all country-specific

statutory regulations are observed

(e.g. in Germany the requirements of

the federal state's fire regulations).

If there is to be simultaneous operation of an extractor

hood and a room-air supplied fireplace (e.g. gas, oil, or

coal fired heaters, fireplaces, water heaters, gas hobs

or ovens), the following requirements must be met:

Ø Your local master chimney sweep has approved

the installation of the extractor hood.

Ø The installation must be done taking the country-

specific regulations of your federal state into

account (e.g. the state fire regulations).

Ø The installation must be done taking all the

regulatory and legal requirements into

consideration (e.g. state building codes).

In extracted air mode, the device draws in air from the

room and expels it outwards through the exhaust pipe.

The device can only extract the amount of air that is

drawn into the kitchen.

The cross-section, length, type and course of the

exhaust pipe affect the extraction efficiency of an

extractor hood greatly.

Power loss and noise can be created by tightly diverted

air in the exhaust pipe.

To ensure optimum performance of the device, you

should ensure that, when installing the exhaust hose:

§ The exhaust hose is as short and direct as possible.

§ The room air to be extracted is able to flow freely

through the exhaust pipe without turbulence and

back pressure.

§ The prescribed cross-section of the exhaust pipe is

observed.

§ The recommended composition of the exhaust pipe

is maintained throughout its length.

The following section explains what the requirements

and properties of the exhaust pipe should be.

Exhaust in a separate exhaust duct.

DANGER

Suffocation risk from smoke or fumes.

Ø Make sure that the exhaust channel

used is only used and designed for

operating an exhaust hood.

Ø Ensure that the exhaust channel is

only used by this device. If

connecting the device to an active

exhaust duct, like a ventilation shaft

or chimney, gases or fumes could be

drawn into the room.

DANGER

Fire hazard due to flammable exhaust

pipe.

Running a flammable exhaust pipe

through a second room or attic could

spread a fire into other rooms.

Ø Ensure that the exhaust pipe is

made of non-combustible material in

accordance with DIN 4102 class A1.

You may only extract the room air through a separate

and suitably designed exhaust channel to the outside.

Ø Ensure that the exhaust channel used is only used

by this device as an exhaust pipe.

Installation instructions

30 Installation instructions

Exhaust pipe optimisation

Room air extracted on the direct route

Lead the room air extracted directly and via the

shortest route to the outside. Long routes create

additional, unwanted air resistance.

Ø Ensure that the exhaust pipe is directly fed outside

via the shortest route.

Use pipes with low air resistance

Only use tubes with a smooth surface on the inside.

Such pipes have a low air resistance.

Avoid the installation of:

§ Spiral hoses

§ Flexible tubes

§ Flat corner pieces.

These types of tubes have a higher air resistance and

reduce the performance of the extractor hood.

Ø Make sure that the exhaust pipe has a smooth

surface on the inside.

Only use bends with optimal air paths and a smooth

surface on the inside. These bends have low air

resistance (e.g. berbel bends).

Avoid using bends with sharp-edged air guides.

These bends have a high air resistance and produce

noises. These bends reduce the performance of the

extractor hood.

Ø Make sure that the bends in the exhaust pipe have

a smooth surface on the inside and that the air

path is optimised (e.g. berbel bends).

Use a suitable cross-section

The minimum cross-section for the exhaust pipe for the

125-systems (BEH 60/90 and BLB 60 FL/90FL) is 125

mm and for the 150 systems (all other berbel extractor

hoods) is 150 mm.

Every reduction in the exhaust hose causes unwanted

air resistance, performance reduction and noises.

Avoid:

§ Exhaust pipes of a smaller diameter.

§ Sharp-edged exhaust flat air ducts.

§ Conventional wall boxes.

These have a high air resistance and cause noises.

They reduce the performance of the extractor hood.

Ø Make sure that the minimum cross-section of the

exhaust pipe is not less than the cross-section of

the fan outlet.

Ø Use berbel pipes, bends and the optimal berbel

BMK wall box, for example.

Exhaust pipe through an old chimney

DANGER

Suffocation risk from smoke or fumes.

Ø A master chimney sweep must

approve the use of the chimney as

an exhaust pipe prior to installing the

extractor hood.

DANGER

Fire hazard due to flammable exhaust

pipe.

Running a flammable exhaust pipe

through a second room or attic could

spread a fire into other rooms.

Ø Ensure that the exhaust pipe is

made of non-combustible material in

accordance with DIN 4102 class A1.

If you use a chimney as the exhaust pipe, you must

expect increased air resistance in relation to the length

of the chimney.

Installation instructions

Installation instructions 31

The extracted air must be introduced into the chimney

using a 90° bend pointing upwards. This will prevent a

possible back pressure.

Ø Make sure that the connection to the chimney is via

a 90° bend which points upwards.

Exhaust pipe through the roof

DANGER

Fire hazard due to flammable exhaust

pipe.

Running a flammable exhaust pipe

through a second room or attic could

spread a fire into other rooms.

Ø Ensure that the exhaust pipe is

made of non-combustible material in

accordance with DIN 4102 class A1.

ATTENTION

Water damage to the device caused by

lack of a condensation trap.

Ø Fit a condensation trap to the

exhaust pipe.

If you run the exhaust pipe out through the roof, you

must ensure that:

§ The pipe diameter of the fan outlet is not larger than

the diameter of the roof feed through.

§ The roof feed through does not reduce the cross-

section of the exhaust pipe.

§ A sufficiently large condensation trap is integrated

into the exhaust pipe that does not reduce the

cross-section of the exhaust pipe.

Exhaust pipe through the exterior wall

DANGER

Fire hazard due to flammable exhaust

pipe.

Running a flammable exhaust pipe

through a second room or attic could

spread a fire into other rooms.

Ø Ensure that the exhaust pipe is

made of non-combustible material in

accordance with DIN 4102 class A1.

If you run the exhaust pipe out through an exterior wall,

you must ensure that:

§ The diameter along the exhaust pipe is not smaller

than the diameter of the fan outlet.

§ The wall feed through does not reduce the diameter

of the exhaust pipe.

The wall box must meet the following requirements:

§ The diameter of the fan outlet must not be larger

than that of the wall box.

§ The wall box's louvred cover must have a large vent

area.

Installation instructions

32 Installation instructions

Ensure that:

§ The slats of the wall box's louvred cover are not

narrow and thick.

§ The slats of the wall box's louvred cover do not

hang straight down.

§ There is no insect screen fitted in the wall box.

Insect screens impair the cross-section of the

exhaust pipe completely.

Ø Use only flow optimised wall boxes (e.g. BMK F/L).

Description for the installer

Installation instructions 33

Basics about the device

The BLB 60 FLE and BLB 90 FLE devices are

operated with an external fan.

To ensure the device functions optimally, it is

essential to observe the prescribed volume flows!

These devices can only be used in extracted air

mode.

The diameter of the pipe connection for the BLB

60 FL and BLB 90 FL devices

is Ø 125 mm.

The diameter of the pipe connection for the BLB

60 FLE and BLB 90 FLE devices

is Ø 150 mm.

The BLB 60 FLE and BLB 90 FLE devices can

also be delivered with a side (right or left) 150

mm x 80 mm large flat duct connection.

The device is designed to be installed flush in

cupboards.

The device is controlled using the controls in the

middle of the front panel.

Description for the installer

34 Installation instructions

Device view from above



Fan module BLB 60 FL  Right bracket



Fan module BLB 90 FL  Left bracket



As a option, only for BLB 60 FLE and BLB 90 FLE:

Side flat channel connector 150 mm x 80 mm



Only BLB 60 FLE and BLB 90 FLE:

Connection socket for external fan



Fan outlet 

Mains plug





Contact terminals for the window switch and the

wall box



Description for the installer

Installation instructions 35

Device view from underneath with a closed lower section



Fan module BLB 90 FL  Lower section



Fan module BLB 60 FLE  Illumination



Rotary knob (on and off switch)

Description for the installer

36 Installation instructions

Device view from underneath with opened lower section



Fan module BLB 90 FL  Capillary trap



Fan module BLB 60 FLE  Lower section



Upper section

Preparation for installation

Installation instructions 37

Preparation for installation

In this chapter you will learn what the prerequisites are

for installation. Perform all the steps in this guide one

after the other.

Ø Make sure that all the safety instructions from the

chapters "General Safety Instructions" and "Safety

Instructions for the Installer" are followed.

WARNING

Risk of injury from falling parts with

improper fastening or too low bearing

capacity of the cabinet.

Ø Ensure that the cabinet has sufficient

bearing capacity.

Do not attempt to carry out the

installation where the required

bearing capacity cannot be assured.

Ø Only use suitable fastening

materials.

The supplied fastening material is

only to be used for fastening into a

stable cabinet (e.g. 16 mm wooden

sheets). If there are other installation

conditions, you can ask your

architect for example, about

alternative fastening methods before

installation.

Ø Ensure that the device is correctly

suspended.

Ø Ensure that the power supply meets the voltage

supply specified on the ratings plate.

Ø Ensure that the connection to the power supply is

made after the device is installed.

Ø Make sure that the device can be disconnected on

all poles from the electricity supply after

installation.

Qualifications of personnel

Two persons are required to mechanically install the

device.

These technicians must have sufficient craftsman skills

and knowledge.

The required specialist skills include:

§ Knowledge of the regulations on safety at work

§ Ability to read technical drawings

§ Experienced in using electrical and mechanical

tools

§ Knowledge of fastening systems

§ Basic knowledge of ventilation systems

§ It would be ideal to have several years experience

in installing extraction hoods and further additional

qualifications, like an apprenticeship as a carpenter

for example.

Persons without this specialist knowledge must be

trained by an experienced technician in the installation.

Prerequisites for the mechanical end
assembly

The required prerequisites for the installation include:

§ The cabinet is has sufficient bearing capacity.

§ The socket for the power supply is to be provided

on-site, installed by a qualified electrician.

§ For the BLB 60 FLE and BLB 90 FLE:

The external fan is fitted.

The cable to control the external fan is laid on-site

to the installation position.

§ For exhausted air and hybrid operation:

The connection cables for the wall boxes and/or

window contact switches are laid on-site to the

installation position.

§ For exhausted air and hybrid operation:

The exhaust pipe is laid on-site to the installation

location.

Preparation for installation

38 Installation instructions

Brief overview of the installation

The installation is done in the following steps:

§ Remove the lower section.

§ Remove the capillary trap.

§ Tighten up the lever of the fastening mechanism.

§ Remove the bracket.

§ Determine the exact installation location.

§ Make the installation cut-out here.

§ Install the brackets.

§ Mount the device.

§ Secure the device.

§ For the BLB 60 FLE and BLB 90 FLE:

Connect the control cable from the external fan.

§ When using a wall box or a window contact switch:

connect the cable.

§ When in recirculated air or hybrid mode:

insert the filter.

§ When in exhausted air or hybrid mode:

attach the exhaust pipe.

§ Plug in the plug for the power supply.

§ Attach the remaining parts.

Prepare the plug socket for the power supply

DANGER

Lethal electric shock caused by

improper connection.

Ø Working on the power supply may

only be done by qualified, trained

electricians adhering to the country-

specific regulations and standards

(e.g. in Germany DIN 57100 / VDE

0100, part 701).

DANGER

Danger, for example of a fatal electric

shock by faults caused by an

inaccessible plug socket.

Ø Ensure that the power plug is freely

accessible so that you can easily

and simply isolate the device from

the power supply in an emergency.

Ø If the plug socket is not easily

accessible, an all-pole isolating

device (with a contact gap of at least

3 mm) must be provided on-site.

Ø Only allow the required plug socket to be installed

by a qualified electrician.

Ø Ensure that a plug socket is installed at a

maximum separation distance of 1.2 metres.

Ø Make sure that the building electrical supply is

properly earthed.

Ø Make sure that the power supply voltage meets the

value on the ratings plate on the inside of the

device.

Ø Ensure that the connection to the power supply is

made after the device is installed.

Preparation for installation

Installation instructions 39

Prepare the connection cable for the power
supply

The connection to the in-house power supply is made

using a power plug. The power cable fitted to the

device is 1.3 metres long.

Ø Make sure that the device can be disconnected on

all poles from the electricity supply after installation

(the switch should have a minimum 3 mm opening

gap).

Ø Make sure that the power supply voltage meets the

value on the ratings plate on the inside of the

device.

Ø Make sure that the mains voltage is turned off for

the remainder of the installation of the device.

Prepare the connection cables for wall box and
window contact switch

You can connect the device to a window contact switch

and a berbel wall box (e.g. BMK F). The cable clamps

are fitted to the device's housing. The connection

cables should be laid prior to installing the device.

Wiring diagram for the window contact and the
wall box contact

ATTENTION

You can damage the electronics if you

connect the control cables with the

wrong polarity.

Ø Make sure that you connect the right

poles of the control cable.

Ø Connect wire 1 to connector 1, and

wire 2 to connector 2.





Terminal for the multi-function contact (F-K)



Terminal for the wall box (BMK)



Control cable



Power supply



Wall box BMK F



Control contact, potential-free



Control box of the berbel extractor hood

Preparation for installation

40 Installation instructions

Tools and equipment needed

For installation you need the following tools, materials

and documents:





Folding ruler

 Pencil
 Cross-head screwdriver
 2.5 mm ball Allen key
 Jigsaw
 Thick cardboard e.g. to protect the cooking hob

and the work surface

 These installation instructions

Unpacking

CAUTION

Risk of injury from broken glass.

Ø Wear protective gloves.

Ø Unpack the device carefully.

Ø Do not touch broken glass.

ATTENTION

Damage to the surfaces from improper

unpacking.

Ø Cut the packing tape and straps with

scissors.

Ø Do not cut into the protective

cardboard packaging.

ATTENTION

Scratched surfaces from metallic,

sharp-edged objects, e.g. belt buckles

or tools during transport.

Ø Transport the device without any

contact to objects that could scratch

the device.

Ø Remove the packing foil and the cardboard

packaging.

Ø If present, cut off the holding strap with scissors.

Preparation for installation

Installation instructions 41

Ø Cut the packing tape using scissors.

Ø Take the loose parts out of the packaging.

CAUTION

Risk of injury from the heavy extractor

hood falling.

Ø Lift the device only with two persons.

Ø Protect the surfaces of the working area, e.g. using

thick cardboard.

Ø Remove the parts from the packaging.

Ø Place the pars on a level, protected surface.

Check the delivery

Ø Makes sure that all the parts are complete as

described in the following section.

Ø Check the delivered parts for damage.

Ø If any parts are damaged or missing, contact your

berbel dealer or customer services.

Scope of delivery BLB 60 FL(E)



Fan module BLB 60 FL(E)



Left bracket



Right bracket



Installation Instructions



6 x screws (cross-head) 4.5 x 16 mm

Only for BLB 60 FLE:

The connection cable for an external fan (e.g.

BAL 150) is included with the fan. The cable is 5

m long.

Preparation for installation

42 Installation instructions

Scope of delivery BLB 90 FL(E)



Fan module BLB 90 FL(E)



Left bracket



Right bracket



Installation Instructions



8 x screws (cross-head) 4.5 x 16 mm

Only for BLB 90 FLE:

The connection cable for an external fan (e.g.

BAL 150) is included with the fan. The cable is 5

m long.

Optional accessories





Only for hybrid mode:

Hybrid filter BHF 125



Only for recirculated air mode:

Recirculated air filter BUF 125 +



Wall box BMK F/L

Remove the parts for installation

Prior to installation, there are individual components

that must be removed or dismantled to be able to

safely install the device.

Ø Perform the following steps sequentially.

Ø Place the device on its back on a flat, clean and

protected surface.

The following illustrations show a device that is

already installed. They are only as a guide for the

installer. The device must lie on its back for the

following steps, and the actions are to be

implemented according to the perspective.

Preparation for installation

Installation instructions 43

Remove the lower section

Ø Open the lower section by pulling the lower section

downwards on the rounded edge.

Ø Grasp the lower section on its sides with both hands

when it is hanging down perpendicularly.

Ø Lift the lower section about 2 cm (1.).

Ø Loosen the lower section by pulling it forwards (2.).

Ø Remove the lower section.

Remove the capillary trap

Ø Grasp the sides of the capillary trap with both hands.

Ø Pull the capillary trap downwards using both hands.

Preparation for installation

44 Installation instructions

Remove the bracket

To remove the bracket from the device, proceed as

follows:

Ø Press both levels at the side in the bay for the

capillary trap backwards (1.) until they are heard to

click into place.

Ø Pull off both brackets (2.).

Ø Label the brackets "Left" and "Right".

Create the installation cut-out

The installation cut-out must have the following

dimensions:

BLB 60 FL

BLB 60 FLE

BLB 90 FL

BLB 90 FLE

Width "X"

(in mm)

540 mm 840 mm

Depth "Y"

(in mm)

338 mm 338 mm

Minimum distance

"Z"

to the rear wall

(in mm)

15 mm 15 mm

You need a saw for this work step (e.g. jigsaw).

Ø Protect all the surfaces of your working area from

damage, e.g. using thick cardboard or foam.

Installing the device

Installation instructions 45

Ø Cut out the installation cut-out in accordance with the

dimensions specified for your device.

Installing the device

WARNING

Risk of injury from falling parts.

Ø Ensure that no-one is below the working

area during the work.

WARNING

Risk of injury from falling parts if improperly

fastened.

Ø Ensure that the cabinet has sufficient

bearing capacity.

Ø Only use suitable fastening materials.

The supplied fastening material is only to

be used for fastening into a stable cabinet

(e.g. 16 mm wooden sheets). If there are

other installation conditions, you can ask

your architect for example, about

alternative fastening methods before

installation.

Ø Ensure that the device is correctly

suspended.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

The device is suspended using two brackets.

Installing the device

46 Installation instructions

Safety distances are observed

The following illustrations show the operation or

dimensions.

The devices used are shown as symbols. The

illustrations are meant to serve as a guide. The

illustrated device shapes may differ from your

device.

The following statutory minimum separation distances

must be observed:

Description Size

Y 0 mm

X For gas hobs:

at least 650 mm.

For electric hobs:

at least 350 mm.

Recommended distance:

550 mm

Fitting the bracket BLB 60 FL(E)

The supplied brackets are suitable for 16 mm to

22 mm thick cabinet bases. The corresponding

dimension must be adjusted by the installer.

For this work step you need a large Phillips

screwdriver.

Both removed brackets are screwed from above onto

the base plate of the cabinet.

The brackets are pre-set in the factory for 16 mm thick

base plates. The brackets must only be adjusted for

thicker base plates.

The brackets consist of two parts which are screwed

together. One part of the bracket is fitted with slotted

holes. You can adjust the bracket to the base plate

thickness by sliding it.

Ø Loosen both screws.

Ø Adjust to the required dimension by sliding the upper

part of the bracket accordingly.

Ø Re-tighten up both screws.

Ø Ensure that both brackets are correctly adjusted.

Both bent metal tabs are above and point to the interior

of the cabinet.

Ø Place the right-hand bracket from above on the rear

corner of the installation cut-out (1.) until the

fastening tabs lie on the base plate.

Ø Ensure that the bracket lies flush.

Ø Screw the bracket flush to the side edge (2.).

Ø Slide the bracket rearwards (3.) until the bracket lies

flush to the rear edge.

Ø Ensure that the bracket is flush with the rear and the

side edges of the installation cut-out.

Ø Fasten the bracket with the cross-head screws (4.)

included in delivery.

Ø Tighten up the cross-head screws.

Installing the device

Installation instructions 47

Ø Ensure that the bracket is firmly mounted in the

correct installation position.

Ø Repeat this process with the left-hand bracket.

Fitting the bracket BLB 90 FL(E)

The supplied brackets are suitable for 16 mm to

22 mm thick cabinet bases. The corresponding

dimension must be adjusted by the installer.

For this work step you need a large Phillips

screwdriver.

Both removed brackets are screwed from above onto

the base plate of the cabinet.

The brackets are pre-set in the factory for 16 mm thick

base plates. The brackets must only be adjusted for

thicker base plates.

The brackets consist of two parts which are screwed

together. One part of the bracket is fitted with slotted

holes. You can adjust the bracket to the base plate

thickness by sliding it.

Ø Loosen both screws.

Ø Adjust to the required dimension by sliding the upper

part of the bracket accordingly.

Ø Re-tighten up both screws.

Ø Ensure that both brackets are correctly adjusted.

Both bent metal tabs are above and point to the interior

of the cabinet.

Ø Place the right-hand holder from above onto the base

plate (1.) until the fastening tabs lie on the base

plate.

Ø Ensure that the bracket lies flush.

Ø Slide the bracket (2.) to the side edge of the

installation cut-out until the bracket lies flush.

Ø Ensure that the bracket lies flush with the base plate.

Ø Ensure that the bracket lies flush to the side edge of

the installation cut-out.

Ø Fasten the bracket with the cross-head screws (3.)

included in delivery.

Ø Tighten up the cross-head screws.

Installing the device

48 Installation instructions

Ø Ensure that the bracket is firmly mounted in the

correct installation position.

Ø Repeat this process with the left-hand bracket.

Hang the device

DANGER

Danger from falling parts if improperly

fastened.

Ø The supplied fastening material is

only to be used for installation into

an installation cut-out in a bearing

and stable wooden cabinet (e.g.

cabinet body).

Ø Make sure that the bearing capacity

is sufficient and use appropriate

fastening material.

For this step you do not require any tools.

Ø Ensure that both levers in the side of the capillary

trap bay are locked into the rear.

Ø With two persons, lift the device from underneath into

the base panel with the installation cut-out.

In the end position, the levers engage automatically

and hold the device.

Ø Push the device upwards until both levers engage.

Ø Ensure that both levers have engaged.

Installing the device

Installation instructions 49

Align the device horizontally

For this step you do not require any tools.

You can slightly adjust the horizontal alignment of the

device. Proceed as follows:

Ø Push the device into the desired position by pushing

against the device on the side with your hand.

Secure the lock

For this work step you need a 2.5 mm ball Allen key.

To secure the lever after installing the device, proceed

as follows:

Ø Tighten the lever using your thumb.

Ø Screw both levers tight with the corresponding screw.

Installing the device

50 Installation

instructions

Only BLB 60 FLE / BLB 90 FLE:
Connect the connection cable of the fan

DANGER

Lethal electric shock caused by

improper connection.

Ø Only allow work on the power supply

to be carried out by qualified, trained

electricians adhering to the country-

specific regulations and standards

(e.g. in Germany DIN 57100 / VDE

0100, part 701).

WARNING

Risk of falling during work carried out

at height.

Ø Use a stable step-ladder.

CAUTION

Risk of injury from falling parts.

Ø Ensure that no-one is underneath

the working area while you are

working.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

The connection cable must be laid from the external

fan to the receptacle on the device.

Only BLB 60 FLE / BLB 90 FLE:
Receptacle pin assignments

The receptacle is wired as follows:

Receptacle pin no. Description

1 Level 1

2 Level 2

3 Level 3

4 Level 4

5 N

6 PE

Only BLB 60 FLE / BLB 90 FLE:
Controlling the individual fan speeds

Ø Ensure that only one power level can be switched

on at any one time.



Level 1  PE



Level 2  N



Level 3  L



Level 4

For this work step, you do not need any tools to

connect the berbel connection cable.

Proceed as follows:

Ø Push the plug of the connection cable firmly into the

receptacle on the device.

The connection cable for the fan is connected.

Installing the device

Installation instructions 51

Connecting the wall box and the window
contact switch contacts

DANGER

Lethal electric shock caused by

improper connection.

Ø Only allow work on the power supply

to be carried out by qualified, trained

electricians adhering to the country-

specific regulations and standards

(e.g. in Germany DIN 57100 / VDE

0100, part 701).

Ø Only allow a qualified electrician to carry out the

following steps.

You can connect the device to a window switch and a

berbel wall box (e.g. BMK F). The cable clamps for this

are attached to the fan housing of the device.

Wiring diagram for the window contact and the
wall box contact

ATTENTION

You can damage the electronics if you

connect the control cables with the

wrong polarity.

Ø Make sure that you connect the right

poles of the control cable.

Ø Connect wire 1 to connector 1, and

wire 2 to connector 2.





Terminal for the multi-function contact (F-K)



Terminal for the wall box (BMK)



Control cable



Power supply



Wall box BMK F



Control contact, potential-free



Control box of the berbel extractor hood

Terminals for the wall box

The terminals for the wall box automatically control the

remote-controlled BMK wall box.

The control cable needs to be laid from the wall box to

the connection terminals for the wall box in the

extractor hood.

The terminals are marked in the extractor hood with

"BMK" or "wall box".

To connect the control cable, you need to attach the

two wires of the control cable to the terminals 1 and 2

for the wall box in the extractor hood. The wires are

marked with numbers. The control contact is potential-

free.

Installing the device

52 Installation

instructions

§ The wall box is closed when the control contacts in

the extractor hood are open (see wiring diagram).

§ The wall box is open when the control contacts in

the extractor hood are closed.

In the following section, the connection of the BMK F

model series wall box is described.

For this work step, you need a small Phillips

screwdriver for the connection terminals in the berbel

extractor hood.

Ø Lay the control cable from the wall box to the

extractor hood.

Ø Make sure that the terminals for the wall box are

accessible in the extractor hood.

In the top corner of the control box are the terminals for

the window contact switch and the wall box contacts.

The terminals are labelled with "Fensterschalter"

(window switch) and "BMK" or "Mauerkasten" (wall

box). The terminal pairs are marked with 1 and 2.

To connect the control cable, proceed as follows:

Ø Open the screw of the BMK terminal 1.

Ø Take the wire 1 of the control cable.

Ø Insert wire 1 into terminal 1.

Ø Make sure that the wire-end ferrule of the control

cable is completely inserted into the terminal.

Ø Make sure that the insulation of the control cable is

not in the terminal.

Ø Tighten the screw of terminal 1.

Installing the device

Installation instructions 53

Ø Connect the cable wire 2 in the same way to the

BMK terminal 2.

The control cable for the wall box is now connected.

Terminals for the window contact switch

You can connect a window contact switch to the

terminals for the window contact switch. The extractor

hood's fan is only operational when the window is

open.

The control cable needs to be laid from the window

switch to the connection terminals for the window

contact switch in the extractor hood.

The terminals for the window contact switch are

marked in the extractor hood with "Fensterschalter"

(window switch).

To connect the control cable, you need to attach the

two wires of the control cable to the terminals 1 and 2

for the window contact switch in the extractor hood.

The following step describes how the window contact

switch is connected.

For this work step, you need a small Phillips

screwdriver for the connection terminals in the berbel

extractor hood.

Ø Lay the window switch's control cable to the

device.

Ø Make sure that the terminals for the window

contact switch are accessible in the extractor hood.

In the top corner of the fan box are the terminals for the

window contact switch and the wall box contacts. The

terminals are labelled with "Fensterschalter" (window

switch) and "BMK" or "Mauerkasten" (wall box). The

terminal pairs are marked with 1 and 2.

To connect the control cable, proceed as follows:

Ø Open the screw of the "Fensterschalter" terminal 1.

Ø Take the wire 1 of the control cable.

Ø Insert wire 1 into terminal 1.

Ø Make sure that the wire-end ferrule of the control

cable is completely inserted into the terminal.

Ø Make sure that the insulation of the control cable is

not in the terminal.

Installing the device

54 Installation

instructions

Ø Tighten the screw of terminal 1.

Ø Connect the cable wire 2 in the same way to the

"Fensterschalter" terminal 2.

The control cable for the window contact switch is now

connected.

Creating the exhaust air connection

You can install the device for different operating

modes:

§ Recirculated air mode

§ Extracted air mode

§ Hybrid mode

The installation for the individual operating modes is

described in the following sections.

Installing the device for recirculated air mode

WARNING

Risk of falling when changing the filter

or during work carried out at height.

Ø Use a stable step-ladder.

CAUTION

Risk of injury from falling parts.

Ø Ensure that no-one is underneath

the device while working.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

To make sure that the filter are installed correctly,

a guide is fitted to the device's filter seating.

The filter is inserted correctly when the bottom edge of

the filter is parallel to the top edge of the fan's housing

and the gap is approximately 5 mm wide.

Ø Insert the recirculated air filter from the top onto the

guide of the fan housing.

Ø Make sure that the filter is fitted correctly.

Installing the device

Installation instructions 55

Installing the device for extracted air mode

WARNING

Risk of falling during work carried out

at height.

Ø Use a stable step-ladder.

CAUTION

Risk of injury from falling parts.

Ø Ensure that no-one is underneath

the device while working.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

Ø Push the exhaust pipe firmly into place on the

guide on the fan.

Ø Seal the transition between the exhaust pipe and

the guide with the help of sealing tape.

Ø Ensure that the exhaust pipe is correctly fitted.

Installing the device

56 Installation

instructions

Installing the device for hybrid mode

WARNING

Risk of falling when changing the filter

or during work carried out at height.

Ø Use a stable step-ladder.

CAUTION

Risk of injury from falling parts.

Ø Ensure that no-one is underneath

the device while working.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

To make sure that the filter are installed correctly,

a guide is fitted to the device's filter seating.

The filter is inserted correctly when the bottom edge of

the filter is parallel to the top edge of the fan's housing

and the gap is approximately 5 mm wide.

Ø Place the hybrid filter onto the guide on the fan

housing from above.

Ø Make sure that the filter is fitted correctly.

Ø Push the exhaust pipe onto the filter collar.

Ø Ensure that the exhaust pipe is correctly fitted.

Installing the device

Installation instructions 57

Install the other parts

After installation, fit the parts removed as follows:

Insert the capillary trap

Ø Place the capillary trap with both hands into the

device, and push it firmly upwards.

The capillary trap snaps into place.

Reassemble the lower section.

Ø Grip the lower section with both hands.

Ø Insert the lower section into the device from below

until the guide grooves of the lower section are in

front of the device guide pins at the same time.

Ø Press the lower section rearwards into the device

(1.).

Ø Pull the lower section downwards (2.) until it clicks

into place.

Ø Make sure that the lower section is fitted correctly.

The lower section is fitted correctly when you can

move it easily.

Close the lower section.

Ø Close the lower section by pushing it upwards until

the two magnetic fasteners can be heard to click

together.

Ø Remove any remaining protective foil from the

device.

Initial cleaning

58 Installation i

nstructions

Connect the power supply

DANGER

Lethal electric shock caused by

improper connection.

Ø Only allow work on the power supply

to be carried out by qualified, trained

electricians adhering to the country-

specific regulations and standards

(e.g. in Germany DIN 57100 / VDE

0100, part 701).

Ø Insert the mains power plug into a power outlet.

The berbel extractor hood is installed and ready for

use.

Initial cleaning

ATTENTION

Damage to the surfaces from sharp

objects or abrasive cleaning agents.

Ø Never use sharp objects, abrasive or

aggressive cleaning agents.

Ø Use a soft, damp cloth.

Cleaning the surfaces

Ø Clean the surfaces with a soft, damp cloth and a

mild household cleaner.

Ø Dry the surfaces using a soft cloth.

Cleaning the controls

Ø Clean the surface of the control panel with a soft,

damp cloth.

Ø Dry the surfaces using a soft cloth.

Disassembling the device

Installation instructions 59

Disassembling the device

DANGER

Lethal electric shock caused by

improperly performed electrical work.

Ø Only allow work on the power supply

to be carried out by a qualified

electrician adhering to the country-

specific regulations and standards

(e.g. in Germany DIN 57100 / VDE

0100, part 701).

WARNING

Risk of falling when changing the filter

or during work carried out at height.

Ø Use a stable step-ladder.

CAUTION

Risk of injury from falling parts.

Ø Ensure that no-one is underneath

the device while working.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

To remove the device you need a second person.

For this work step, you need a small flat-head

screwdriver, a Phillips screwdriver and a 2.5 mm ball

Allen key.

To remove the device, proceed as follows:

Ø Disconnect the power supply to the device on all

poles.

Ø Remove the mains plug.

Ø Remove the connection cables for the wall box and

the multi-function contact, if fitted.

Only BLB 60 FLE and BLB 90 FLE:

Ø Remove the connection cable for the fan.

Only for hybrid and extracted air mode:

Ø Remove the exhaust pipe.

Only for hybrid and recirculated air mode:

Ø Remove the filter.

Ø Open the lower section.

Ø Remove both screws on the levers.

ATTENTION

Damage caused by falling parts.

Ø Protect areas and devices (e.g.

cooled cooking hob) underneath the

working area against damage, e.g.

using a thick piece of cardboard.

Ø Support the device with two people.

Ø Push both levers backwards until they lock.

Ø Lower the device with two people.

Ø Loosen the screws on the brackets.

Ø Remove the screws on the brackets.

Ø Remove the brackets.

The device is disassembled.

Disposal

60 Installation

instructions

Disposal

Disposal of the packaging

DANGER

Danger of suffocation from packaging

components (e.g. foils and

polystyrene).

Ø Store the film or other parts of the

packaging in a location which is

inaccessible to children.

ATTENTION

Environmental damage caused by

incorrect packaging disposal.

Ø The packaging must not be disposed

of in normal household waste.

Ø Bring or send the packaging to an

environmentally friendly and correct

recycling facility.

The packaging is there to protect against damage

during transportation.

Only the original packaging guarantees sufficient

protection during transportation.

Ø Keep the packaging during the warranty period.

The packing materials were chosen with environmental

considerations in mind and are made from recyclable

materials. The packing materials can be returned into

the raw material cycle after use. As a result valuable

resources can be saved.

§ The outer packaging is made from cardboard.

§ The filling materials and layers are of cardboard of

polystyrene.

§ The protective foils and bags are made of

polyethylene.

Ø Dispose of the packaging, separated into material

groups, in an environmentally friendly way.

Disposal

ATTENTION

Environmental damage caused by

improper device disposal.

Ø Do not throw the device away with

the normal household waste.

Ø Check with your town or local council

about the facilities available for a

environmentally friendly and correct

recycling facility or a disposal site.

Ø Make the device unusable after disassembly, by

cutting the disconnected power cable for example.

Ø Dispose of the device according to legal

requirements using a waste management

company.

Technical specifications

Installation instructions 61

Technical specifications

Ratings plate (type label)

The ratings plate is found inside the device behind the

lower section.

The following information

can be found on the ratings plate:

§ Manufacturer

§ Address of manufacturer

§ Device type

§ Voltage

§ Total power

§ Serial number

§ Year of manufacture

§ Symbols of compliance with the legal requirements

and test symbols.

The device was manufactured in compliance with the

regulations of VDE 60335-2-31 and meets the following

regulations and laws:

§ EMC regulation (EC directive 2004/104/EEC)

§ Low Voltage Directive 2006/95/EC.

Subject to technical changes.

Volume flow for operation with an external fan

If you want to operate the device in conjunction with an

external fan, the minimum volume flow rates at the fan

box outlet must be set:

Power level 1: min. 200 m³/h

Power level 2: min. 300 m³/h

Power level 3: min. 400 m³/h

Power level 4: min. 500 m³/h

Fan module BLB 60

BLB 60 FL BLB 60 FLE BLB 90 FL BLB 90 FLE

Width 550 mm 550 mm 850 mm 850 mm

Depth 350 mm 350 mm 350 mm 350 mm

Height 350 mm 245 mm* 350 mm 245 mm*

Max. fan power free

blowing

615 m³/h nom. volume 615 m³/h nom. volume

Pipe connection

(outlet on top)

Ø 125 mm Ø 150 mm Ø 125 mm Ø 150 mm

Pipe connection

(outlet on side)

nom. volume 150 mm x 80 mm

flat duct

nom. volume 150 mm x 80 mm

flat duct

Weight::

(without filter)

approx. 20 kg

approx. 9.5 kg

approx. 22.0 kg

approx. 12.5 kg

Power consumption 160 W 8 W 160 W 10 W

LED lighting 2x3.6 W/24 V 2x3.6 W/24 V 1x7.2 W/24 V 1x7.2 W/24 V

Supply voltage 230 V / 50 Hz 230 V / 50 Hz 230 V / 50 Hz 230 V / 50 Hz

62

Contact

If you have suggestions or queries, please choose from the following possibilities:

Post: berbel Ablufttechnik GmbH

Sandkampstraße 100

D-48432 Rheine

Telephone: [phone] / 80 80 9-0

Mon to Thu 08.00 to 17.00 and Fri 08.00 to 14.00

Fax: [phone]

Internet: www.berbel.de

E-mail: [email protected]

Contacting the customer services of the manufacturer

You can contact our customer service department in different ways: Choose from the following options:

Telephone: [phone]

Mon to Thu 10:00 to 17:00 CET, Fri 10:00 to 14:00

Fax: [phone] / 80 80 9 - 650

E-mail: [email protected]

Contact

63

64

German language original manual created by:
B. Gebhardt - Büro für Technische Dokumentation
45891 Gelsenkirchen
www.tddv.de
Printed in Germany
Version: 04.08.2015 16:21

6001431
Subject to alterations without notice