BenQ Corporation makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability or fitness for any particular
purpose. Further, BenQ Corporation reserves the right to revise this
publication and to make changes from time to time in the contents hereof
without obligation of BenQ Corporation to notify any person of such
revision or changes.
Safety Information
For your safety, please read the guidelines below carefully
before you use your phone:
Your wireless handheld portable telephone is a low power transmitter and
receiver. When it is ON, it receives and also sends out radio frequency
(RF) signals.
European and international agencies have set standards and
recommendations for the protection of public exposure to RF
electromagnetic energy.
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996
• Verband Deutscher Elektringenieure (VDE) DIN- 0848
• Directives of the European Community, Directorate General V in
Matters of Radio Frequency Electromagnetic Energy
• National Radiological Protection Board of the United Kingdom, GS 11,
1988
• American National Standards Institute (ANSI) IEEE. C95.1- 1992
• National Council on Radiation Protection and Measurements (NCRP).
Report 86
• Department of Health and Welfare Canada. Safety Code 6
These standards are based on extensive scientific review. For example,
over 120 scientists, engineers and physicians from universities,
government health agencies and industry reviewed the available body of
research to develop the updated ANSI Standard.
The design of your phone complies with these standards when used
normally.
Safety Informationi
Specific Operating Restrictions
No metallic component allowed in body-worn accessories.
Antenna Care
Use only the supplied or approved replacement antenna. Unauthorized
antennas, modifications or attachments may damage the phone and
violate FCC regulations.
Phone Operation
• Normal Position: Hold the phone as you would with any other
telephone.
• To avoid potential RF interference, please do not wear the phone around
your neck or in front your chest for long hours.
Batteries
• For safety concerns, when the temperature of the phone goes over
°C (113F) or below 0°C (32F), charging will halt.
45
• Do not expose batteries to temperatures below -10
°C (113F). Always take your phone with you when you leave your
45
vehicle.
• Use only genuine BenQ battery to ensure the phone’s normal operation.
All batteries can cause property damage, injury or burns if a conductive
material such as jewelry, keys or beaded chains touches exposed terminals.
The material may complete electrical circuit and become quite hot. To
protect against such unwanted current drain, exercise care in handling any
charged battery, particularly when placing it inside your pocket, purse or
other container with metal objects. When battery is detached from the
phone, your batteries are packed with a protective battery cover; please
use this cover for storing your batteries when not in use.
°C (14F) or above
iiSafety Information
Driving
Check the laws and regulations on the use of wireless telephones in the
areas where you drive. Always obey them. Also, if using your phone while
driving, please:
• Give full attention to driving--driving safety is your first responsibility.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving
conditions so require.
Electronic Devices
Most modern electronic equipment is shielded from RF signals. However,
certain electronic equipment may not be shielded against the RF signals
from your wireless phone.
Pacemakers
The Health Industry Manufacturers Association recommends that a
minimum separation of six (6") inches be maintained between a handheld
wireless phone and a pacemaker to avoid potential interference with the
pacemaker. These recommendations are consistent with the independent
research by and recommendations of Wireless Technology Research.
Persons with pacemakers:
• Should ALWAYS keep the phone more than six inches from their
pacemaker when the phone is turned ON.
• Should not carry the phone in a breast pocket.
• Should use the ear opposite the pacemaker to minimize the potential for
interference.
If you have any reason to suspect that the interference is taking place, turn
your phone OFF immediately.
Hearing Aids
Some digital wireless phones may interfere with some hearing aids. In the
event of such interference you may want to consult your hearing aid
manufacturer to discuss alternatives.
Safety Informationiii
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of
your device to determine if they are adequately shielded from external RF
energy. Your physician may be able to assist you in obtaining this
information.
Turn your phone OFF in health care facilities when any regulations posted
in these areas instruct you to do so. Hospitals or health care facilities may
be using equipment that could be sensitive to external RF energy.
Ve h i c l e s
RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles. Check with the manufacturer or its
representative regarding your vehicle. You should also consult the
manufacturer of any equipment that has been added to your vehicle.
Posted Facilities
Turn your phone OFF in any facility where posted notice so requires.
Aircraft
FCC regulations prohibit using your phone while in the air. Switch OFF
your phone before boarding an aircraft.
Blasting Areas
To avoid interfering with blasting operations, turn your phone OFF when
in a “blasting area” or in area posted “TURN OFF TWO-WAY RADIO.”
Obey all signs and instructions.
Potentially Explosive Atmospheres
Turn your phone OFF and do not remove the battery when in any area
with a potentially explosive atmosphere and obey all signs and
instructions. Sparks, from your battery, in such areas could cause an
explosion or fire resulting in bodily injury or even death.
ivSafety Information
Areas with a potentially explosive atmosphere are often, but not always
clearly marked. They include fueling areas such as gasoline stations; below
deck on boats; fuel or chemical transfer or storage facilities; vehicles using
liquefied petroleum gas (such as propane or butane); areas where the air
contains chemicals or particles, such as grain, dust, or metal powders; and
any other area where you would normally be advised to turn off your
vehicle engine.
For Vehicles Equipped with an Air Bag
An air bag inflates with great force. DO NOT place objects, including both
installed or portable wireless equipment, in the area over the air bag or in
the air bag deployment area. If in-vehicle wireless equipment is
improperly installed and the air bag inflates, serious injury could result.
Federal Communications Commission
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiated radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
Safety Informationv
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
European Union Directives Conformance Statement
This device complies with the OJ-Directive as below:
Electromagnetic Compatibility Directive (89/336/EEC), Low Voltage
Directive (73/23/EEC)
And R&TTE Directive (99/05/EEC).
And also complies with the standard:
3GPP TS 51.010-1
EN 301 511
EN 50360/ EN 50361
ETSI EN 301 489-1/-7
EN 60950
viSafety Information
Table of Contents
Safety Information ...........................................................i
1. Preparing Your Phone For Use................................... 1
Inserting a SIM Card ............................................................ 1
Installing the Battery ............................................................ 2
Charging the Phone.............................................................. 3
Turning the Phone On ......................................................... 4
The miniSD Card ................................................................. 5
2. Getting to Know Your Phone ..................................... 6
Your Phone at a Glance........................................................ 6
1. Turn the phone over, and release the battery latch. Lift the battery off
the phone.
Battery latch
Do not remove the battery when the phone is on. Doing so could
cause you to lose personal settings or data stored either on your SIM
card or in the phone's memory.
2. Slide the SIM card into the SIM card slot, with the SIM card's metal
contacts facing downwards and the cut corner at the bottom left.
SIM card
SIM card slot
A SIM card can be easily damaged if its metal contacts become
scratched. Therefore, take special care when holding or inserting it.
Preparing Your Phone For Use1
T o remove the SIM ca rd, you must first press down the stay, then push
the SIM card out of the slot.
Stay
SIM card
Installing the Battery
With the battery's metal contacts facing downwards, align the
protruding tabs on the end with the holes in the battery bay. Then push
the battery toward the end of the bay to insert the battery's tabs into the
holes. Press down to click the battery into place.
Do not remove the battery when the phone is on. Doing so could
cause you to lose personal settings or data stored either on your SIM
card or in the phone's memory.
2Preparing Your Phone For Use
Charging the Phone
1. Insert the charger connector deep into the charger socket at the
bottom of your phone. Ensure that the connector is plugged in the
right direction with the side showing arrow icon facing upwards.
2. Plug the charger into a power outlet.
Do not remove the battery while the phone is charging.
3. Once the phone is fully charged, remove the charger from both the
power outlet and the phone.
Please note:
• It takes approximately 4 hours to fully charge a batt ery.
• When the battery is weak, the phone will play an alert sound.
• When the battery is discharged, the charging may not start immediately
when you plug in the connector. Wait 10 to 15 minutes for the phone to
begin charging.
Preparing Your Phone For Use3
Tur nin g the Pho ne O n
1. Press and hold to turn the phone on. The phone will display the
welcome animation.
2. Enter your PIN code and press
The PIN (Personal Identification Number) is the password provided
by your network operator. You need this password in order to use the
SIM card.
If you enter the PIN incorrectly three times in a row, the SIM card will
be locked. You must now enter the PUK (Personal Unblocking Key)
for that SIM card in order to unlock it. Please contact your network
operator to obtain a PUK.
To activate/disable PIN password authentication, go to Settings >Security > PIN Code > PIN 1 Code > Settings. See page 68.
3. When the PIN code entered has been accepted, the phone will
automatically search for the designated network. This search process
may take a few seconds.
4. The standby screen will be displayed, as well as network signal
strength and the name of the network operator. You can now use the
phone.
If the phone is not able to detect the designated network, or links to a
network that you are not authorized to use, the signal strength meter
will show no bars. You will only be able to make emergency calls.
to confirm.
4Preparing Your Phone For Use
The miniSD Card
Your phone features a miniSD slot designed specifically for use with the
miniSD card, a removable flash memory card intended to add greater
storage capacity to your phone.
The miniSD card enables you to store multimedia data, including
images, photos, MP3 audio files, ring tones, and Java games.
Installing the miniSD Card
1. Lift the cover.
2. Insert the miniSD Card into the slot. Ensure that the card's metal
contacts face downwards.
3. Close the cover.
Please note:
• will appear in the status bar when the miniSD card is loaded.
• Your phone does not support a miniSD card which is on FAT32 or NTFS
format.
Removing the miniSD Card
1. Lift the cover.
2. Press the miniSD card to release it.
Preparing Your Phone For Use5
Getting to Know Your Phone
Your Phone at a Glance
Front and side views
External display
Camera lens
Camera flash
Charger socket
Antenna
Rubber cover
IrDA port
To view what is behind the rubber cover, lift the cover and twist it to the
left.
miniSD slot
Hands-free headset /
Data cable jack
6Getting to Know Your Phone
Side and back views
Battery latch
Battery
Speaker
Camera key
Vol u m e k e y
Getting to Know Your Phone7
Earpiece
Main Display
OK key
Left soft key
Camera key
Dial/Answer key
WAP ke y
8Getting to Know Your Phone
Navigation keys
Right soft key
Clear key
Power on/off key
Alphanumeric keys
Microphone
External Display
When the flip is closed, the external display's status bar will show icons
for network strength, battery power, alarm(if set active), the current
time and the current profile in use. The external display will also alert
you to incoming calls, new messages and missed calls.
Standby Screen
Status bar
Name of network
operator
Press to enter the
indicated function.
Press to enter the
main menu.
Press to enter the
indicated function.
• To set the wallpaper of the display, go to Settings > Display >
Wallpaper. Alternatively, you can go to Media Center > Images.
See page 52and page 63.
• To set the current time and date, as well as the format to be
shown, go to Settings > Date & Time. See page 61.
Getting to Know Your Phone9
Icons in the Status Bar
IconFunctionDescription
Signal strength
Battery status
GPRS in useAppears when GPRS has been activated.
3GShows 3G coverage area.
BluetoothAppears when Bluetooth is turned on.
SMS Message
MMS Message
WAP message
Email
Voicemail
AlarmAppears when the alarm is turned on.
Signal strength of the network. The more
bars indicated, the stronger the signal.
Shows the current level of battery power.
The more bars indicated, the more power
remains.
Appears when you have new or unread SMS
messages.
Appears when you have new or unread
MMS messages.
Appears when you have new or unread
WAP messages.
Appears when you have new or unread
email messages.
Appears when you have new voicemail
messages (this icon will only appear if the
function is supported by your network
operator).
Keypad lockAppears when the keypad is locked.
/
Line1 or Line 2
in use
Shows that Line1 or Line2 is now in use.
10Getting to Know Your Phone
IconFunctionDescription
NormalShows that the Normal profile is activated.
Flight Mode
Headset
MeetingShows that the Meeting profile is activated.
SilentShows that the Silent profile is activat ed.
Outdoors
DivertAppears when the call divert is activated.
Roaming
SD CardAppears when a SD card is loaded.
Appears when the Flight Mode profile is
activated.
Appears when a headset is connected to the
phone.
Shows that the Outdoors profile is
activated.
Roaming is activated (not your regular
network).
Using the Keys in Idle Mode
In this user manual, "long-press" means to press and hold down a key
for about two seconds. "Press" means to press a key and release
immediately.
KeyCommands and functions
Power on/off key
• Long-press to turn the phone on or off.
• Press this key to end a call, reject an incoming call, or
to cancel a dialing.
Getting to Know Your Phone11
KeyCommands and functions
Send/Answer key
• Press to send or answer a call.
• Press to access the call record list.
Left soft key
• Press to perform the function indicated on the display.
Right soft key
• Press to perform the function indicated on the display.
• Long-press to turn the silent profile on or off.
OK key
• Press to open up the main menu.
Navigation key
• Press to use the MP3 player.
• Press to create a new SMS mesage.
• Press to access Media Center.
• Press to access Profiles menu.
Asterisk key
• Press this key to enter an asterisk " * ".
• To make an international call, long-press this key until
the display shows "+", then enter the recipient's country
code, area code and phone number.
Voicemail key
• Long-press to dial your voicemail number.
12Getting to Know Your Phone
KeyCommands and functions
# key
• Press to enter "#".
• For extensions: After entering a phone number, long-
press to enter a "P" and then enter the extension
number.
• Long-press this key to activate the keypad lock.
Alphanumeric keys
• Press to enter digits.
~
• Shortcut key: Long-press a key to immediately access
the function, or dial the number, that it represents. See
page 35, "Messages".
Volume key
• Long press the upper or lower key to adjust the
volume.
Camera key
• Long press to activate the camera mode.
• In camera mode, it functions as a shutter button.
Menu Navigation
1. In idle mode, press to bring up the main menu.
2. Use the scroll key to move up, down, right or left through the menu,
for example, scroll to Settings, and press to enter its menu.
Getting to Know Your Phone13
Loading...
+ 61 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.