Copyright 2003 by BENQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of this company.
Disclaimer
BENQ Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BENQ Corporation reserves the right to revise this publication and to make changes from time to
time in the contents hereof without obligation of this company to notify any person
of such revision or changes.
*Windows, Internet Explorer and Outlook Express are trademarks of Microsoft
Corporation. Others are copyrights of their respective companies or organizations.
Taking care of your camera
• Do not use your camera in the following environmental range: temperature below 0°C
or above 40°C.
• Do not use or store your camera in the environments listed below:
– Direct sunlight
– High humidity and dusty places
– Next to the air conditioner, electric heater or other heat sources
– In a closed car that is directly under the sun
– Unstable locations
• If your camera becomes wet, wipe it with dry cloth as soon as possible.
• Salt or seawater may cause severe camera damage.
• Do not use organic solvents, such as alcohol, etc., to clean your camera.
• If the lens or viewfinder is dirty, use a lens brush or soft cloth to clean the lens. Do not
touch the lens with your fingers.
• To prevent electrical shock, do not attempt to disassemble or repair your camera by
yourself.
• Water may cause a fire or electric shock. Therefore, store your camera in a dry place.
• Do not use your camera outdoors when it is raining or snowing.
• Do not use your camera in or near water.
• If a foreign substance or water gets in your camera, please turn the power off immediately and disconnect the batteries and the transformer. Remove the foreign substance or
water, and send it to the maintenance center.
• Transfer the data to the computer as soon as possible to avoid losing your image data.
Table of Contents
BenQ DC 5330 Table of Contents
1. Touring your DC S30 1
1.1 Checking the Package Contents ............................1
1.2 DC S30 Components ............................................2
1.2.1 Front View ............................................................2
If anything is missing or appears damaged, contact your dealer. Save the packaging in the
event you need to ship your camera for service.
Touring your DC S30
1
BenQ DC 5530 User’s Manual
English
1.2 DC S30 Components
1.2.1 Front View
1. Speaker
2. Shutter button
3. Built-in flash
4. Optical viewfinder
5. Lens/lens cover
6. Self-timer/AF assist lamp
7. Microphone
8. Earphone and A/V OUT terminal
9. USB port
10. DC IN 5V terminal
1.2.2 Rear View
1. Shutter button
2. Flash/right navigation button
3. Zoom/volume adjust/menu
up & down navigation button
4. Macro/left navigation button
5. Viewfinder LED
6. Viewfinder
7. LCD panel
8. Quick View/delete button
9. Menu/cancel
10. LCD/SET
11. Mode dial
12. Strap attachment
1.2.3 Bottom View
1. Tripod socket
2. Battery cover open detector
Note: Do not touch this detector.
3. Lithium ion battery compartment
4. SD memory card slot
1
2
3
4
5
6
6
M
7
8
9
A
O-VIEW/DEL
MENU-C
LCD/SET
10 111212
7
8
9
10
12345
12 3 4
Notes
•
The LCD on the digital camera is manufactured with sophisticated technology.
However, the display may have some light spots or show unusual colors. This is
normal and does not indicate display malfunction, and will not affect the pictures
you take with the camera.
• The AF assist lamp is used to illuminate the focus subject in low light situations
where other camera’s autofocus will likely have failed.
2
Touring your DC S30
BenQ DC 5530 User’s Manual
1.2.4 Button Functions
1. Macro
• Recording/Video Mode – press this button
to enable Macro mode.
• Playback Mode – press to select previous
file.
• Menu Mode – press to move left in the
menus.
• MP3 Mode – press to skip to the previous
track.
• FM Radio Mode – press to scan for a
previous channel.
2. Zoom
• Recording/Playback/Video Mode – press
up to zoom in; press down to zoom out.
• MP3/FM Radio Mode – press up to
increase the volume; press down to decrease
it.
• Thumbnail Mode – press up or down to navigate thumbnail images.
• Menu Mode – press up or down to change values.
3. Flash
• Manual Record Mode – press button to cycle through Flash modes.
• Playback Mode – press to select next file.
• MP3 Mode – press to skip to the next track.
• FM Radio Mode – press to scan for the next channel.
• Menu Mode – press to move right in the menus.
4. Mode Dial (refer to next page)
5. Q-View/Delete
• Recording Mode – press to view the last image that was taken.
• Playback Mode – press to delete current image or movie.
• MP3 Mode – press for less than two seconds to switch between playback modes
(repeat all, repeat one, standard play). Press for more than two seconds to lock
camera buttons; only the power button functions in this mode.
• FM Mode – press for two seconds to lock buttons; only the power button functions in
this mode. Press for less than two seconds to switch the audio output between the
earphone and speaker.
6. Menu/Cancel
• Recording/Playback/Video Modes – opens the menus.
• Menu Mode – cancels an operation or exits menu mode.
7. LCD/SET
• Recording/Video Mode – press to switch between display modes: OSD (on-screendisplay) full display, OSD display OFF, and LCD OFF.
• Playback Mode – press to switch between playback modes: standard image, image
only, and thumbnail mode.
•Menu Mode – press to confirm action.
• MP3 Mode – press to toggle between play and pause modes.
• FM Radio Mode – press for less than two seconds to switch FM radio stations. Press
for more than two seconds to save the current station to a channel; select the channel
to tune to the station.
Q-VIEW/DEL
MENU/C
LCD/SET
1
2
3
4
5
6
7
English
Touring your DC S30
3
BenQ DC 5530 User’s Manual
1.2.5 Mode Dial
English
1. Manual Mode
2.Auto mode
3.Playback mode
1
2
3
4
4.Movie mode
5.Audio Mode
5
1.2.6 Viewfinder LED Indicator
GreenOrange
1. Power on detected
2. Ready to use or AF action
ON
Blinking (slow)
Blinking (fast)Accessing mass storageFlash is charging
completed
3. USB connection
(non accessing)
Processing
1.2.7 Rotating the LCD Panel
The LCD panel can be rotated 180 degrees as shown,
enabling you to take pictures of yourself.
Battery charging in progress
1. Warning message
2. Power low
4
Touring your DC S30
BenQ DC 5530 User’s Manual
2PREPARING YOUR DC S30 FOR USE
The Lithium Ion battery enables you to capture images and video clips, and listen to music or
FM radio on the go. Use the AC adapter whenever possible to conserve battery power.
2.1 Inserting the Battery
1. Turn the camera off.
2. Slide the battery cover in the direction of the
arrow (A) and open the battery cover (B).
3. Push the battery latch in the direction of the
arrow (C) and insert the battery in the correct orientation as shown (D) with the
notches facing up.
4. Close the battery/SD Memory Card cover (E).
To remove the battery: Open the battery cover and
then push the battery latch. The battery pops out
slightly; pull the battery out.
Notches
Battery latch
M
A
Q
-VIEW/DEL
MEN
U-C
L
C
D
/S
E
T
B
O
V
I
E
W
MENU/C
L
C
D
/
S
E
T
Q
-V
IE
M
EN
U-C
L
C
D
/S
E
T
O
V
I
E
W
MENU/C
L
C
D
/S
E
T
English
A
D
E
L
A
M
A
W
/D
E
L
A
D
E
L
D
C
Notes
Use only the specified battery type (Lithium Ion).
•
• If you are not going to use the battery for an extended period of time, remove it
from the camera to prevent leakage or corrosion.
• Avoid using battery in extremely cold environments as low temperatures can
shorten the battery life and reduce camera performance.
Preparing Your DC S30 for Use
E
5
BenQ DC 5530 User’s Manual
English
2.2 Using an AC Power Adapter
1. Make sure the camera power is off.
2. Connect one end of the AC power adapter to the
DC IN 5V terminal (A).
3. Connect the other end of the AC power adapter to
a power outlet (B).
B
A
Use only the AC power adapter specified for the camera. Damage caused by the use of
•
an incorrect adapter is not covered under the warranty.
• Use an AC power adapter while transferring images to your computer in order to pre-
vent data loss from unexpected automatic power off of the camera.
Notes
2.3 Charging the Battery
1. Insert the battery as described in 2.1“Inserting the Battery” on page 5.
2. Connect the AC power adapter as described in the previous section, or connect the USB
cable to your camera and a USB enabled device such as a notebook or PC.
The following describes the LED indicators:
• Orange LED: charging starts
• LED Off: charging is complete
Notes
Use only the AC power adapter specified for the camera. Damage caused by the
•
use of an incorrect adapter is not covered under the warranty.
• When using the USB cable to charge the camera, turn the camera off for better
charging performance.
• Avoid exposing the camera to hot temperatures. Use it at room temperature for
best results.
6
Preparing Your DC S30 for Use
BenQ DC 5530 User’s Manual
LOCK
2.4 Loading an SD Memory Card
All images and video clips taken by the camera can be stored in an SD (Secure Digital)
Memory Card as well as the camera’s internal memory. Even if the camera’s power is OFF, the
images saved in the SD Memory Card are not erased.
1. Make sure the camera is off.
2. Slide the battery/SD Memory Card cover in the
direction of the arrow on the cover.
3. Insert an SD Memory Card:
• The front side of the memory card (printed
arrow) should face towards the front side of
the camera.
• If the card cannot be inserted, check the ori-
entation.
4. Close the battery/SD Memory Card cover.
To remove the SD Memory Card, make sure the camera is off. Open the battery/SD Memory
Card card cover. Press lightly on the edge of the memory card and it will eject.
Notes
To prevent valuable data from being
•
accidentally erased from an SD Memory
Card, slide the write-protect tab (on the
side of the SD Memory Card) to
"LOCK ".
Press the tab in the
direction of the arrow
on the card to write
protect the SD Memory
Card.
Write-protect tab
• To save, edit, or erase data on an SD
Memory Card, you must unlock the card.
• Format your SD Memory Card before use. Refer to 3.5.1“Memory” on page 28.
M
A
Q
V
I
E
W
/
D
E
L
M
E
N
U
-C
L
C
D
/
S
E
T
English
Preparing Your DC S30 for Use
7
BenQ DC 5530 User’s Manual
English
2.5 Attaching the Strap
To prevent accidentally dropping the
camera when using your camera, always
use the strap.
1. Thread the small loop of the hand
strap through the strap eyelet on the
camera (A).
2. Pull the large loop through the small
loop until the strap is firmly secured (
A
B
).
B
8
Preparing Your DC S30 for Use
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.