Benq BL2706HT User Manual

BL2706HT LCD Monitor
User Manual

Copyright

Copyright © 2016 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specically disclaims any warranties, merchantability or tness
for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of such revision or changes.
The performance of icker-free may be affected by external factors such as poor cable quality,
unstable power supply, signal interference, or poor grounding, and not limited to the above
mentioned external factors. (Applicable for icker-free models only.)

Servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any of the above mentioned misuse or other accident such as
dropping or mishandling occurs, contact qualied service personnel for servicing.

Safety

Please follow these safety instructions for best performance, and long life for your monitor.
• The AC plug isolates this equipment from the AC supply.
• The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet should be installed near the equipment and be easily accessible.
This product should be operated from the type of power indicated on the marked label. If you are
not sure of the type of power available, consult your dealer or local power company.
• An approved power cord greater or equal to H03VV-F or H05VV-F, 2G or 3G, 0.75mm
used.
2
must be

Care And Cleaning

Cleaning. Always unplug your monitor from the wall outlet before cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any liquid, aerosol or glass
cleaners.
Slots and openings on the back or top of the cabinet are for ventilation. They must not be blocked or covered. Your monitor should never be placed near or over a radiator or heat source, or in a
built-in installation unless proper ventilation is provided.
• Never push objects or spill liquid of any kind into this product.
2

BenQ ecoFACTS

BenQ has been dedicated to the design and development of greener product as part of its aspiration to realize the ideal of the “Bringing Enjoyment ‘N Quality to Life” corporate vision with the ultimate
goal to achieve a low-carbon society. Besides meeting international regulatory requirement and
standards pertaining to environmental management, BenQ has spared no efforts in pushing our initiatives further to incorporate life cycle design in the aspects of material selection, manufacturing,
packaging, transportation, using and disposal of the products. BenQ ecoFACTS label lists key eco-
friendly design highlights of each product, hoping to ensure that consumers make informed green choices at purchase. Check out BenQ’s CSR Website at http://csr.BenQ.com/ for more details on BenQ’s environmental commitments and achievements.
3
Table of Contents
Copyright ................................................................................................................ 2
Disclaimer .............................................................................................................. 2
Servicing .................................................................................................................. 2
Safety ....................................................................................................................... 2
Care And Cleaning ............................................................................................... 2
BenQ ecoFACTS .................................................................................................. 3
Box contents ......................................................................................................... 5
Installation .............................................................................................................. 6
Attach the monitor stand ...............................................................................................................6
Install the headphone hook ............................................................................................................6
Cleaning ..............................................................................................................................................7
Adjusting the monitor height ........................................................................................................8
Rotating the monitor .......................................................................................................................9
Adjusting Viewing angle ............................................................................................................... 10
Connecting the monitor .............................................................................................................. 11
Removing the monitor stand ...................................................................................................... 12
Using the monitor wall mounting kit ........................................................................................ 13
The control panel ............................................................................................... 14
Basic OSD menu operation ........................................................................................................ 15
Power LED indicator .................................................................................................................... 15
Menu introduction ..............................................................................................16
Getting the most from your BenQ monitor ................................................ 18
How to install the monitor on a new computer ................................................................... 19
How to upgrade the monitor on an existing computer....................................................... 20
How to install on Windows 10 system .................................................................................... 21
How to install on Windows 8 (8.1) system ............................................................................. 22
How to install on Windows 7 system ...................................................................................... 23
Troubleshooting .................................................................................................. 24
Need more help? ........................................................................................................................... 25
Specication ......................................................................................................... 26
BL2706HT ....................................................................................................................................... 26
Preset display modes ......................................................................................... 28
Plug & Play DDC2B feature .............................................................................. 28
3/21/17
4

Box contents

**
When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement.
LCD Monitor
Quick Start Guide
Monitor Base
Headphone Hook
Power Cable
& CD-ROM Disc
D-Sub Cable HDMI Cable
*: Optional accessory.
Available accessories and the pictures shown here may differ from the actual contents and the product
supplied for your region. For cables that are not supplied with your product, you can purchase them separately.
Consider keeping the box and packaging in storage for use in the future when you may need to transport the monitor. The tted foam packing is ideal for protecting the monitor during transport.
Always keep the product and accessories out of reach of small children.
DVI Cable
Audio Cable
5

Installation

• If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to
the monitor until instructed to do so.
The following illustrations are for your reference only. Available input and output jacks may vary depending on the purchased model.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.

Attach the monitor stand

1. Protect the monitor and screen by clearing a at open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding.
2. Gently lay the screen face down on a at clean padded surface.
3. Orient and align the stand base socket with the end of the stand arm, then push them together until they click and lock into place.
4. Tighten the screw on the bottom of the monitor base as illustrated.
5. Carefully lift the monitor, turn it over and place it upright on its stand on a at even surface.
You should position the monitor and angle the screen to minimize unwanted reections from other light
sources.

Install the headphone hook

You can install the headphone hook to place your headphone. It is useful when your headphone is not in use.
1. Orient and align the headphone hook with the hole
2
on the monitor stand, and attach the hook to the hole (
).
1
2. Turn the hook clockwise until you can not go further ( ). The headphone hook is ready to use.
The maximum load capacity of the headphone hook is 500g.
6

Cleaning

Please disconnect the power cord before cleaning the product.
Clean the cabinet regularly with a cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
7

Adjusting the monitor height

To adjust the monitor height, hold both the left and the right sides of the monitor to lower the monitor or lift it up to the desired height.
• Avoid placing hands on the upper or lower part of the height-
adjustable stand or at the bottom of the monitor, as ascending or descending monitor might cause personal injuries. Keep children out of reach of the monitor while performing this operation.
If the monitor has been rotated to portrait mode and height adjustment is desired, you should be noted that the wide screen will keep the monitor from being lowered to its minimum height.
8

Rotating the monitor

1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 degrees.
Right-click the desktop and select Screen resolution from the popup menu. Select Portrait in Orientation, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen orientation. Refer to the help document of your operating system for details.
2. Fully extend the monitor and tilt it.
Gently lift the display up and extend it to the maximum extended position. Then tilt the monitor.
The monitor should be vertically extended to allow to rotate from landscape to portrait mode.
3. Rotate the monitor 90 degrees clockwise as illustrated.
90
To avoid the edge of the LCD display hitting the monitor base surface while it is being rotated, do tilt and extend the monitor to the highest position before you start to rotate the display. You should also make sure there are no obstacles around the monitor and there is enough room for cables.
9
4. Adjust the monitor to the desired viewing angle.

Adjusting Viewing angle

You may position the screen to the desired angle with the monitor tilt, swivel, and height adjustment
functions. Refer to the product specications for details.
10

Connecting the monitor

BL2706HT
2
5
3
1
No. Description
1 AC power input jack 2 HDMI socket
3 DVI socket 4 D-Sub socket 5 Audio Line In
6 Audio Line Out
4
6
1. To protect equipment, always turn off the PC and LCD monitor before connecting.
2. Connect the plug of the HDMI cable to the HDMI port on the monitor. Connect the other end of the cable to the HDMI port of a digital output device.
3. Connect the plug of the DVI cable to the monitor DVI socket. Connect the other end of the cable to the DVI port of the computer.
4. Connect the plug of the D-Sub cable (at the end without the ferrite lter) to the monitor video socket. Connect the other end of the cable (at the end with the ferrite lter) to the computer
video socket.
5. You can insert the headset into headphone jack beside the input pin on the back of display.
6. Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, please refer to “Troubleshooting” on 24.
11

Removing the monitor stand

1. Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable.
2. Protect the monitor and screen by clearing a at open area on your desk and placing a soft item
like a towel on the desk for padding, before laying the screen face down on a at clean padded
surface.
3. Release the screw on the bottom of the monitor base and detach the monitor base as illustrated.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
12

Using the monitor wall mounting kit

The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with at surface.
• Ensure that the wall material and the standard wall mount bracket (purchased separately) are
stable enough to support the weight of the monitor. Refer to the product specications for weight
information.
Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor stand.
• Lay the screen face down on a clean and well-
padded surface.
Release the thumbscrew on the bottom of the monitor base.
• Use a a cross-pointed screwdriver to release the screws that xing the monitor stand to the
2
monitor. The use of a magnetic-head screwdriver
is recommended to avoid of losing the screws.
Then pull the monitor stand backward away from the monitor.
In case you intend to use your monitor on the stand in the future, please keep the monitor base, monitor stand, and screws somewhere safe for future use.
1
2. Follow the instruction manuals of the wall mount bracket you purchased to complete the installation.
Use four M4 x 10 mm screws to x a VESA standard wall mount bracket to the monitor. Make sure that all
screws are tightened and secured properly. Consult a professional technician or BenQ service for wall mount installation and safety precautions.
13

The control panel

Source / Auto / Exit
5
2
1
4
3
BL2706HT
No. Description
1 Source / Auto / Exit 2 Low Blue Light / -
3 Volume / +
4 Menu / Enter
5 Power
Press and hold the AUTO key for 3 serconds to adjusts vertical position, phase, horizontal
position and pixel clock automatically.
Press the AUTO key to switch to a desired input source, and conrm with the MENU key.
When in the OSD menu, press to exit.
Low Blue Light / -
Press to select Low Blue Light.
When in the OSD menu, press for Down/Decrease adjustment.
Volume / +
• By default, the key is the hot key for Volume.
When in the OSD menu, press for Up/Increase adjustment.
Menu / Enter
Press to display the OSD menu.
• When in the OSD menu, press to conrm the selection.
Power
Press the button to turn on / off the monitor.
14

Basic OSD menu operation

Press the MENU button to activate the OSD menu.
Press - or + to navigate through the menu options. Once the desired option is highlighted, press
the MENU key to conrm the selection. Press - or + to change the settings of the selected function. Press MENU key to save the new setting and exit the current function. Press - or + to select another function in sub-menu. Press AUTO to exit. If you want to adjust any other function, repeat the previous steps.
OSD Lock: To lock the OSD, press and hold the MENU key while the monitor is off and then
press the while the monitor is off and then press the
If the product screen size is 4:3 or input signal resolution is wide, the Image Ratio is disabled.
key to turn the monitor on. To unlock the OSD, press and hold the MENU button
key to turn the monitor on.

Power LED indicator

LED indicator System status
Blue The monitor is powered on. Orange The monitor is in Standby mode.
15

Menu introduction

Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out. And keys that are not available will be disabled and the corresponding OSD icons will disappear.For models without certain functions, their settings and related items will not appear on the menu.
Main menu Function Range
Luminance Contrast Adjusts the degree of difference between darkness
and lightness.
Brightness Adjusts the balance between light and dark shades. 0-100 Eco mode Select a picture mode that best suits the type of
images shown on the screen.
DCR Sets dynamic contrast ratio. On
AMA OD Function. Off
Image Setup
Color Temp.
Clock Adjusts the pixel clock frequency timing to
synchronize with the analog input video signal.
Phase Adjusts the pixel clock phase timing to synchronize
with the analog input video signal.
H. Position Adjusts the horizontal position of the screen image. 0-100 V. Position Adjusts the vertical position of the screen image. 0-100 Image Ratio This feature is provided to allow aspect ratios
other than 16:9 to be displayed without geometric distortion.
Warm Applies a warm tint to the image and is factory
pre-set to the news print standard white color.
Normal Allows video and still photographs to be viewed
with natural coloring.
Cool Applies a cool tint to the image and is factory pre-
set to the PC industry standard white color.
User The blend of the Red, Green and Blue primary
colors can be altered to change the color tint of
the image. Go to the succeeding R (red), G (green), and B (blue) menus to change the settings.
Decreasing one or more of the colors will reduce
their respective inuence on the color tint of the
image. (e.g. if you reduce the Blue level the image will gradually take on a yellowish tint. If you reduce
Green, the image will become a magenta tint.)
sRGB Recall sRGB Color Temperature from EEPROM.
16
0-100
Standard
Text
Internet
Game
Movie
Sports
Off
High
Premium 0-100
0-100
Wide
4:3
Red
Green
Blue
Main menu Function Range
OSD Setup H. Position Adjusts the horizontal position of the OSD menu. 0-100
V. Position Adjusts the vertical position of the OSD menu. 0-100 Timeout Adjusts the display time of the OSD menu. 5-100 Language Sets the OSD menu language. English
Čeština
Nederlands
Français
Deutsch
Italiano
Polski
Portugues
• Русский
Español
简体中文
Extra Input Select Use this to change the input to that appropriate to
your video cable connection type.
DDC/CI Allows the monitor settings to be set through the
software on the PC.
Reset Resets all mode, color and geometry settings to the
factory default values.
Information Displays the current monitor property settings. Resolution
Low Blue Light
Decreases the blue light emitted from the display to reduce the risk of blue light exposure to your eyes.
繁體中文
Svenska
D-Sub
• DVI
HDMI
On
Off
Yes
No
H.
Frequency
V. Frequency
The value for each Low Blue Light mode indicates how much blue light is decreased compared
with the Standard mode.
Multimedia For viewing multmedia les. -30%
Web
For web surng. -50%
surng Ofce For ofce works or ofce environment. -60%
17

Getting the most from your BenQ monitor

To gain the most benet from your new BenQ LCD monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software. These circumstances relate to which version of Microsoft Windows you are using, and whether you are connecting the monitor and installing the software onto a new computer (without existing
monitor driver software), or whether you are upgrading an existing installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the
monitor to your computer), Windows will automatically recognize the new (or different) hardware,
and will launch its Found New Hardware wizard. Follow the wizard instructions until it asks you to select a monitor model. At that point, click the
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor model. Further details and step-by-step instructions for either an automatic (new) or upgrade (existing) installation, see:
"How to install the monitor on a new computer" on 19.
"How to upgrade the monitor on an existing computer" on 20.
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an
Administrator or as a member of the Administrators group in order to install the monitor driver software.
Furthermore, if your computer is connected to a network which has security access requirements, network
policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specication label on the back of the monitor.
18

How to install the monitor on a new computer

This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver software on a new computer which has never had a monitor driver installed before. This instruction is only suitable for a computer which has never been used before, and for which the BenQ LCD
Monitor is the rst ever monitor to be connected to it.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor
connected to it (and has monitor driver software installed), you should not be following these instructions. You
should instead be following the instructions for "How to upgrade the monitor on an existing computer" on
20.
1. Follow the instructions in "Installation" on 6. When Windows starts, it will automatically detect the new monitor and launch the Found New
Hardware Wizard. Follow the prompts until it displays the option to Install Hardware Device Drivers.
2. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3. Check Search for a suitable driver for my device option, and click Next.
4. Check the option for CD-ROM drives (uncheck all others) and click Next.
5. Look to conrm that the wizard has selected the correct name of your monitor and click Next.
6. Click Finish.
7. Restart the computer.
To nd the suitable driver les for the purchased model, refer to the following table.
Driver les Suitable models
BL2706HT BL2706HT
19

How to upgrade the monitor on an existing computer

This instruction details the procedure for manually updating the existing monitor driver software on your Microsoft Windows computer. It is currently tested as compatible for Windows 10, Windows
8.1, Windows 8, and Windows 7 Operating System (OS).
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
Installing monitor driver software involves selecting an appropriate information le (.inf) on the BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and letting
Windows install the corresponding driver les from the CD. You need only steer it in the right
direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide you
through the le selection and installation process.
See:
"How to install on Windows 10 system" on 21.
"How to install on Windows 8 (8.1) system" on 22.
"How to install on Windows 7 system" on 23.
20

How to install on Windows 10 system

1. Open Display Properties.
Go to Start, Settings, Devices, Devices and Printers and right-click the name of your monitor
from the menu.
2. Select Properties from the menu.
3. Click the Hardware tab.
4. Click Generic PnP Monitor, and then the Properties button.
5. Click the Driver tab and the Update Driver button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the Update Driver Software window, select the option Browse my computer for driver software.
8. Click Browse and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the
drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system - it may be
'D:' or 'E:' or 'F:' etc.
9. Select the correct folder name of your monitor from provided driver list, and click Next.
This will copy and install the appropriate monitor driver les to your computer.
10. Click Close. You may be prompted to restart your computer after the driver update is complete.
21

How to install on Windows 8 (8.1) system

1. Open Display Properties. Move the cursor to the lower-right of the screen or press the Windows + C buttons on the keyboard to bring up the Charm bar. Go to Settings, Control Panel, Devices and Printers
and right-click the name of your monitor from the menu. Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers,
and right-click the name of your monitor from the menu.
2. Select Properties from the menu.
3. Click the Hardware tab.
4. Click Generic PnP Monitor, and then the Properties button.
5. Click the Driver tab and the Update Driver button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the Update Driver Software window, select the option Browse my computer for driver software.
8. Click Browse and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the
drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system - it may be
'D:' or 'E:' or 'F:' etc.
9. Select the correct folder name of your monitor from provided driver list, and click Next.
This will copy and install the appropriate monitor driver les to your computer.
10. Click Close. You may be prompted to restart your computer after the driver update is complete.
22

How to install on Windows 7 system

1. Open Display Properties. Go to Start, Control Panel, Hardware and Sound, Devices and Printers and right-click the name of your monitor from the menu. Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers,
and right-click the name of your monitor from the menu.
2. Select Properties from the menu.
3. Click the Hardware tab.
4. Click Generic PnP Monitor, and then the Properties button.
5. Click the Driver tab and the Update Driver button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the Update Driver Software window, select the option Browse my computer for driver software.
8. Click Browse and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the
drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system - it may be
'D:' or 'E:' or 'F:' etc.
9. Select the correct folder name of your monitor from provided driver list, and click Next. This
will copy and install the appropriate monitor driver les to your computer.
10. Click Close. You may be prompted to restart your computer after the driver update is complete.
23

Troubleshooting

The power LED indicator is not on.
Make the power cord is properly connected to a grounded power outlet and the monitor.
Make sure you have pressed the
The image is blurred.
Read the instructions in "Preset display modes" on 28, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
Remove the extension cable for the test. It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension
cable with better conduction quality or with a built-in booster.
Does the blurring only occur at resolutions lower than the native (maximum) resolution?
Read the instructions in "Preset display modes" on 28. Select the native resolution.
Pixel errors can be seen. One of several pixels is permanently black, one or more pixels are permanently white, one
or more pixels are permanently red, green, blue or another color.
Clean the LCD screen.
• Cycle power on-off.
These are pixels that are permanently on or off and is a natural defect that occurs in LCD
technology.
key.
The image has a faulty coloration. It has a yellow, blue or pink appearance.
If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
No image can be seen.
If the LED is illuminated in blue and there is a message Input Not Support on the screen, this means you are using a display mode that this monitor does not support, please change the setting to one of the supported mode. Please read "Preset display modes" on 28.
Faint shadow from the static image displayed is visible on the screen.
Activate the power management function to let your computer and monitor go into a low power "sleep" mode when not actively in use.
Use a screensaver to prevent the occurrence of image retention.
Is the prompt on the display illuminated in orange?
If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
24
Is the prompt on the display not illuminated at all?
Check the power supply mains socket, the external power supply and the mains switch.
The image is distorted, ashes or ickers.
Read the instructions in "Preset display modes" on 28, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
You are running the monitor at its native resolution, but the image is still distorted.
Images from different input sources may appear distorted or stretched on the monitor running at its native resolution. To have the optimal display performance of each type of input sources, you can use the Image Ratio function to set a proper aspect ratio for the input sources. See "Image Ratio" on 16 for details.
The image is displaced in one direction.
Read the instructions in "Preset display modes" on 28, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
No sound can be heard from the built-in speakers (for models with speakers only):
Check whether Line In is properly connected.
• Increase the volume (volume may be muted or too low).

Need more help?

If your problems remain after checking this manual, please contact your place of purchase or visit the
local website from www.BenQ.com for more support and local customer service.
25
Specication

BL2706HT

Modelname BL2706HT Drivingsystem TFTColorLCD ViewableImageSize 68.6cmdiagonal
Panel
Resolution
Physical
Characteristics
Pixelpitch 0.3114(H)mmx0.3114(V)mm Video R,G,BAnaloglnterface SeparateSync. H/VTTL DisplayColor 16.7MColors DotClock(typical) 144MHz Horizontalscanrange 30~83kHz Horizontalscan
Size(Maximum) Verticalscanrange 55~76Hz VerticalscanSize
(Maximum) Optimalpresetresolution 1920x1080@60Hz Plug&Play VESADDC2B InputConnector D-SUB/DVI/HDMI
InputVideoSignal
Speaker 2Wx2 PowerSource 100-240V
PowerConsumption
ConnectorType D-SUB/DVI/HDMI SignalCableType Detachable Dimensions&Weight: Height(withbase) 431.2~571.2(mm) Width 616.7(mm) Depth 239.6(mm) Weight(headonly) 4.29kg Weight(withbase) 7.04kg Mechanismspec
597.89mm
336.31mm
Analog:0.7Vp-p(standard),75OHM, Positive
30W(typical) Standby0.5W
Tilt(down/up)
Swivel(left/right)
Heightadjustmet
Pivot WallMount 100x100mm
-5°~20°
45°/45°
140mm
~90°clockwise
26
Environmental
Temperature: Operating 0°Cto40°C Non-Operating -25°C-+55°C Humidity: Operating 10%to85%(non-condensing) Non-Operating 5%to93%(non-condensing) Altitude: Operating 0~3658m(0~12000ft) Non-Operating 0~12192m(0~40000ft)
27

Preset display modes

Mode Resolution H.Frequency V.Frequency
VGA
SVGA
XGA
WXGA+ 1280×1024@75Hz 79.976 75.025 Apple,MacII 1152x870@75Hz 68.681 75.062 MACMODESVGA 832×624@75Hz 49.725 74.551 MACMODEXGA 1024×768@75Hz 60.241 74.927
640×480@60Hz 31.469 59.940 640×480@75Hz 37.500 75.00 800×600@60Hz 37.879 60.317 800×600@75Hz 46.875 75.000 1024×768@60Hz 48.363 60.004 1024×768@75Hz 60.023 75.029

Plug & Play DDC2B feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID
information over the DDC2B channel.
28
Loading...