Benq 9H.JHH77.13E User Manual

MU641 Digital Projector User Manual

V 1.01

Warranty and Copyright information

Limited warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright © 2017 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

Patents

Please go to http://patmarking.benq.com/ for the details on BenQ projector patent coverage.

2 Warranty and Copyright information

Table of Contents

Warranty and Copyright information ................................................................................ 2

Important safety instructions .............................................................................................. 4

Introduction .......................................................................................................................... 7

Shipping contents ....................................................................................................................................... 7

Projector exterior view ............................................................................................................................ 9

Controls and functions............................................................................................................................ 10

Positioning your projector ................................................................................................. 13

Choosing a location ................................................................................................................................. 13

Obtaining a preferred projected image size....................................................................................... 14

Mounting the projector ..........................................................................................................................15

Adjusting the projected image ..............................................................................................................16

Connection .......................................................................................................................... 17

Connecting smart devices ...................................................................................................................... 19

Connecting InstaShow (WDC10) ........................................................................................................19

Operation ............................................................................................................................ 20

Starting up the projector ........................................................................................................................20

Using the menus ....................................................................................................................................... 21

Securing the projector ............................................................................................................................ 23

Switching input signal ...............................................................................................................................24

Shutting down the projector ................................................................................................................. 25

Direct power off ...................................................................................................................................... 25

Menu operation ................................................................................................................... 26

Basic menu ............................................................................................................................................... 26

Advanced menu ..................................................................................................................................... 28

Maintenance ........................................................................................................................ 37

Care of the projector .............................................................................................................................. 37

Lamp information ..................................................................................................................................... 37

Troubleshooting ................................................................................................................. 43

Specifications ...................................................................................................................... 44

Projector specifications ..........................................................................................................................44

Dimensions ................................................................................................................................................45

Timing chart............................................................................................................................................... 46

3 Table of Contents

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

1. Please read this manual before you operate your projector. Save it for future reference.

2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3. Refer servicing to qualified service personnel.

6. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where

the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

7. Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, use the blank function.

4. Always open the lens shutter (if any) or

remove the lens cap (if any) when the projector lamp is on.

5. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

4 Important safety instructions

9. Never replace the lamp assembly or any electronic components unless the projector is unplugged.

10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

11. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

13. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

14. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

15. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

12. Do not block the ventilation holes.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

16. When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

5 Important safety instructions

17. Do not place liquids near or on the projector.

3000 m

(10000 feet)

0 m

(0 feet)

Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's power outlet and call BenQ to have the projector serviced.

18. This product is capable of displaying inverted images for ceiling/wall mount installation.

20. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

- Locations near fire alarms

- Locations with an ambient temperature above 40°C / 104°F

- Locations where the altitudes are higher than 3000 m (10000 feet).

19. This apparatus must be earthed.

Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

6 Important safety instructions

Introduction

Digital Projector

Quick Start Guide

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

Projector

Quick start guide Warranty card* Power cord

VGA cable

• The supplied accessories will be suitable for your region, and may differ from those illustrated.

• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

Optional accessories

1. Spare lamp kit

2. 3D glasses

Remote control with

batteries

3. QCast mirror dongle/QCast video streaming dongle/InstaShow (WDC10)

User manual CD

Replacing the remote control batteries

1. Press and slide off the battery cover, as illustrated.

2. Remove the old batteries (if applicable) and install two AAA batteries. Make sure that the positive and negative ends are positioned correctly, as illustrated.

3. Slide the battery cover in until it clicks into place.

7 Introduction

• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

• Never throw the batteries into a fire. There may be danger of an explosion.

• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.

8 Introduction

Projector exterior view

3 4

3 3

1. Lamp cover

9 11

13. RGB (PC) signal input jacks

1412 16

13 17

2. Vent (air exhaust)

3. Adjuster feet

4. Projection lens

5. IR remote sensor

6. External control panel (See Controls and functions on page 10.)

7. Focus ring

8. Vent (air inlet)

9. HDMI-1 input port

10. HDMI-2/MHL-input port (for HDMI dongle)

11. USB Type A port

12. USB Mini-B port

14. RGB (PC) signal output jack

15. RS-232 control port

16. S-Video input jack

17. Video input jack

18. Audio input jacks Audio output jack

19. AC power jack

20. Kensington anti-theft lock slot

21. Ceiling mount holes

9 Introduction

Controls and functions

All the key presses described in this document are available on the remote control or projector.

Projector & Remote control

1 2

3 4

6 7

8 9

1. POWER indicator light/TEMPerature warning light/LAMP indicator light

(See Indicators on page 42.)

2. POWER

Toggles the projector between standby mode and on.

ON/ Off

Toggles the projector between standby mode and on.

3. OK

Confirms the selected On-Screen Display (OSD) menu item.

10 Introduction

4. MENU

Turns on the On-Screen Display (OSD) menu.

5. BACK

Goes back to previous OSD menu, exits and saves menu settings.

6. IR remote sensor

7. Arrow keys ( , , , )

13. SMART ECO

When the On-Screen Display (OSD) menu is activated, these keys are used as directional arrows to select the desired menu items and to make adjustments.

Keystone keys ( , )

Displays the keystone correction page.

Vol um e ke ys /

Decreases or increase the projector volume.

8. SOURCE

Displays the source selection bar.

9. ECO BLANK

Used to hide the screen picture.

Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.

10. AUTO

Automatically determines the best picture timings for the displayed image when PC signal (analog RGB) is selected.

Displays the Lamp Mode menu for selecting a suitable lamp operating mode.

14. FREEZE

Freezes the projected image.

15. ASPECT

Selects the display aspect ratio.

16. Volume keys /

Decreases or increase the projector volume.

17. ZOOM+/ZOOM-

Magnifies or reduces the projected picture size.

18. QUICK INSTALL

Quickly selects several functions to adjust the projected image and displays the test pattern.

19.

Toggles projector audio between on and off.

11. Source selection buttons: PC 1, HDMI.

12. PAG E /PAG E

Operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

11 Introduction

Controlling your smart device with the remote control

When the projector projects the content from your MHL compatible smart device, you can use the remote control to control your smart device.

To enter the MHL mode, press and hold AUTO for 3 seconds. The following buttons are available for controlling your smart device: Arrow keys ( , , , ), MENU, BACK, OK.

To leave the MHL mode, press and hold AUTO for 3 seconds.

When the projector is under MHL mode, the keypad on the projector should be with the same definition of the keys on the remote control.

Remote control effective range

The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor(s) on the projector that might obstruct the infra-red beam.

• Operating the projector from the front • Operating the projector from the top

12 Introduction

Positioning your projector

Choosing a location

Before choosing an installation location for your projector, take the following factors into consideration:

• Size and position of your screen

• Electrical outlet location

• Location and distance between the projector and the rest of your equipment

You can install your projector in the following ways.

1. Front Table

Select this location with the projector placed on the table in front of the screen. This is the most common way to position the projector for quick setup and portability.

3. Front Ceiling

Select this location with the projector suspended upside-down from the ceiling in front of the screen. Purchase the BenQ Projector Ceiling Mount Kit from your dealer to mount your projector on the ceiling.

2. Rear Table

Select this location with the projector placed on the table behind the screen. Note that a special rear projection screen is required.

4. Rear Ceiling

Select this location with the projector suspended upside-down from the ceiling behind the screen. Note that a special rear projection screen and the BenQ Projector Ceiling Mount Kit are required for this installation location.

After turning on the projector, go to Advanced Menu - Settings > Projector Installation, press OK and press / to select a setting.

You can also use QUICK INSTALL on the remote control to access this menu.

13 Positioning your projector

Obtaining a preferred projected image size

Projection distance

Center of lens

Screen

16:10 Screen diagonal

The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size.

Projection dimensions

• The screen aspect ratio is 16:10 and the projected picture is in a 16:10 aspect ratio

Screen size Projection Distance (mm)

Diagonal

Inch mm

30 762 404 646 948 1043 1137

40 1016 538 862 1264 1390 1516

50 1270 673 1077 1580 1738 1895

60 1524 808 1292 1897 2086 2275

70 1778 942 1508 2213 2433 2654

80 2032 1077 1723 2529 2781 3033

90 2286 1212 1939 2845 3128 3412

100 2540 1346 2154 3161 3476 3791

110 2794 1481 2369 3477 3823 4170

120 3048 1615 2585 3793 4171 4549

130 3302 1750 2800 4109 4519 4928

140 3556 1885 3015 4425 4866 5307

150 3810 2019 3231 4741 5214 5686

160 4064 2154 3446 5057 5561 6065

170 4318 2289 3662 5374 5909 6445

180 4572 2423 3877 5690 6257 6824

190 4826 2558 4092 6006 6604 7203

200 5080 2692 4308 6322 6952 7528

250 6350 3365 5385 7902 8690 9477

300 7620 4039 6462 9483 10428 11373

H (mm) W (mm)

Min distance

(with max zoom)

Average

Max distance

(with min zoom)

For example, if you are using a 120-inch screen, the recommended projection distance in the "Average" column is 4171 mm.

If your measured projection distance is 4500 mm, the closest match in the "Average" column is 4519 mm. Looking across this row shows that a 130'' (about 3.3 m) screen is required.

To optimize your projection quality, we suggest to do the projection within non-gray area.

14 Positioning your projector

All measurements are approximate and may vary from the actual sizes.

Ceiling/Wall mount screw: M4 (Max L = 25 mm; Min L = 20 mm)

Unit: mm

238.12

83.48

168.69

21.51

BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

Mounting the projector

If you intend to mount your projector, we strongly recommend that you use a proper fitting BenQ projector mounting kit and that you ensure it is securely and safely installed.

If you use a non-BenQ brand projector mounting kit, there is a safety risk that the projector may fall down due to an improper attachment through the use of the wrong gauge or length screws.

Before mounting the projector

• Purchase a BenQ projector mounting kit from the place you purchased your BenQ projector.

• BenQ recommends that you also purchase a separate Kensington lock compatible security cable and attach it securely to both the Kensington lock slot on the projector and the base of the mounting bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.

• Ask your dealer to install the projector for you. Installing the projector on your own may cause it to fall and result in injury.

• Take necessary procedures to prevent the projector from falling off such as during an earthquake.

• The warranty doesn’t cover any product damage caused by mounting the projector with a non-BenQ brand projector mounting kit.

• Consider the surrounding temperature where the projector is ceiling/wall mounted. If a heater is used, the temperature around the ceiling may be higher than expected.

• Read the user manual for the mounting kit about the range of torque. Tightening with torque exceeding the recommended range may cause damage to the projector and subsequently falling off.

• Make sure the power outlet is at an accessible height so that you can easily shut down the projector.

Ceiling/Wall mount installation diagram

15 Positioning your projector

+ 34 hidden pages