Page 1
Service Manual
SB-9015D
Page 2
Page 3
Copyrights
i
Copyrights
©2010 Logic Controls Technology Corp. All rights
reserved. The information in this document is subject to
change without prior notice in order to improve reliability,
design and function and does not represent a
commitment on the part of the manufacturer.
This document contains proprietary information
protected by copyright. All rights are reserved. No
part of this manual may be reproduced by any
mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
All trademarks are property of their respective
owners
Liability Disclaimer
In no event will the manufacturer be liable for direct,
indirect, special, incidental, or consequential
damages arising out of the use or inability to use the
product or documentation, even if advised of the
possibility of such damages.
The information in this document is subject to
change without notice
Page 4
Contents
ii
Contents
Copyrights .................................................................................................i
Liability Disclaimer ...................................................................................i
Contents....................................................................................................ii
1. Before You Start ...................................................................................1
2. Opening the Device..............................................................................2
Mainboard side Components Replacement...........................................4
3. Mainboard Layout ................................................................................4
4. HDD Replacement ................................................................................9
5. LCD Inverter Replacement ................................................................10
6. LCD Panel Replacement....................................................................11
Page 5
1
1.
1. Before You Start
1. Please unplug the power cable before you start to work.
2. Please read and follow the instructions in this document carefully. Failure to
follow these instructions could damage your device and void the warranty.
1.1. Tools Suggested
All procedures in this document require the following tools:
#0 Phillips screwdriver #1 Phillips screwdriver
(Magnetized suggested) (Magnetized suggested)
1.5 mm hexagon socket spanner
(Magnetized suggested)
Page 6
2
2.
2. Opening the Device
1. Loosen the screw as shown.
2. Separate the device from the base.
3. Un-tighten the four screws on the back panel anticlockwise.
Page 7
3
4. Separate the back panel from the front panel by lifting up and lay it down
carefully.
Page 8
4
3.
Mainboard side Components Replacement
3. Mainboard Layout
For relative location of onboard connectors, please refer to the pictures below.
Page 9
Chapter 3
5
1. Open the two ejectors on the slot by pushing them, and remove the RAM
from the slot.
2. Align and insert the new RAM into the slot and push both ends of the
RAM down until the ejectors snap into place.
3. Disconnect the SATA cable from the SATA HDD1 connector of the main
board.
4. Disconnect: 1. VGA cable, 2 LVDS (LCD) cable, 3. inverter cable, 4. led
CABLE, 5. speaker cable and 6. power switch cable from the mainboard.
Page 10
6
5. Disconnect: 1. Parallel port cable and 2. Touch panel cable.
6. Loosen the two screws by 1.5 mm hexagon socket spanner as shown
below.
7. Loosen the four screws fixing the mainboard.
Page 11
Chapter 3
7
8. Remove the mainboard.
9. Loosen the four screws by 1.5 mm hexagon socket spanner as shown
below, and then you can remove the VGA port cable and the parallel port
cable.
10. Loosen the two screws as shown and remove the IO bracket.
Page 12
8
11. Remove the power switch.
Page 13
9
4.
4. HDD Replacement
1. Loosen the four screws by #1 Phillips screwdriver and Unplug the SATA cable and
power cable from the HDD, then you can remove the HDD assembly.
2. Loosen the four screws fixing the HDD on the both side, and then you can remove
the HDD.
3. Install the new HDD in the reverse procedure from Step 4 to Step 1.
Page 14
10
5.
5. LCD Inverter Replacement
1. Disconnect three connecters shown below.
2. Disconnect three connecters and three screws from LCD inverter as
shown below, and then you can remove the LCD inverter.
3. Install the new LCD inverter in the reverse procedure.
Page 15
11
6.
6. LCD Panel Replacement
1. Unplug the LED indicator.
2. Disconnect the touch panel cable.
3. Loosen the two screws and remove the led indicator len.
4. Remove the black tape and then disconnect the LCD cable.
Page 16
12
5. Loosen the six screws as shown and remove the LCD assembly from the front bezel.
6. Loosen the four screws as shown, and then you can remove the LCD from the LCD
chassis.
Loading...