Page 1
www.logiccontrols.com www.bematechus.com
QUICK START GUIDE
LR2000 and LR2000E
Logic Controls, Inc. LR2000 Series
POS Thermal Printers
INSTALLATION
1. Connect the interface cable (USB/serial) to the printer.
2. Connect the other end of interface cable (USB/serial) to the computer.
3. For Ethernet interface, connect the Ethernet cable to Ethernet hub,
switch, or router.
4. Connect cash drawer cable to cash drawer port at the back of printer.
(Use 12-24V/1A cash drawer only. Incompatible cash drawer will cause
damage to both the cash drawer and the printer.)
5. Make sure the AC power is unplugged and the printer is powered off
before connecting the power cord.
6. Connect DC power cord to printer and then AC power plug to wall socket.
7. Turn on the power switch on the printer side.
Paper Roll Recommendation
Paper Roll Specification Manufacturer
HPK-110 Hansol patech Co.,Ltd
AF50KS-E JUJO Paper Co.,Ltd
TF-50KS-E Nippon Paper Industries Co.,Ltd
PD-160R New Oji Paper Mfg,Co.,Ltd
F380 Kansaki Specialty Papers,Inc.
LOAD AND REPLACE PAPER ROLL
1. Press the Button to Open Paper Roll Cover
2. Remove the used paper roll to replace with a new roll
3. Load the paper roll as shown below:
Make sure the paper roll is loaded in the correct direction.
Correct Direction Wrong Direction
4. Pull out the roll paper to the bottom front of the printer and then close the
cover as shown below.
5. Tear off extra paper roll with auto-cutter or with tear-cutter of the printer.
Improper paper roll may lead to critical fault on printer head and shortened
the machine life span. Thus be sure to use the recommended paper roll.
Any issue caused by using other branded paper roll will void the warranty,
even during the warranty period.
USB RS232
LAN
(LE2000E)
CASH
DRAWER
DC IN
Press down to
close cover
Press the Cover
Release Button
Page 2
www.logiccontrols.com www.bematechus.com
QUICK START GUIDE
LR2000 and LR2000E
Logic Controls, Inc. LR2000 Series
OPERATION
Printer Controls Panel
Setting Printer Mode
Switch Function ON OFF
1 Select cutter Disable cutter Enable cutter
2 Select buzzer Enable buzzer Disable buzzer
3 Printing density High density Regular density
4 2-byte character mode
Disable 2-byte
characters
Enable 2-byte
Characters
5 Characters per line 42 48
6 Cash drawer output Enable Disable
7-8
Baud rate for serial interface (refer to table below）
Baud rate（bps)
SW-7 SW-8
38400 ON ON
115200 OFF ON
9600 ON OFF
19200 OFF OFF
SPECIFICATIONS
Characteristics Specification
Printing
Property
Printing Method Thermal Line printing
Resolution 180x180dpi (7 dots/mm)
Paper Width 79.5±0.5mm
Printing Width 72mm
Character Font
ASCII Font A：12X24
ASCII Font A：9X24
Printer Density 512dot/line
Printing Speed 250mm/s
NV bitmap Flash 64kb
Receipt Buffer 8kb
Communication Interfaces
LR2000 - USB and Serial
LR2000E - USB, Serial and Ethernet
Power Adaptor
Input Voltage
AC 100～240V, 50/60Hz
Output Voltage
DC 24V，2.5A
Environment
Operating Temperature
0～45°C
Storage Temperature
-10～50°C
Operating Humidity 10-80%
Storage Humidity 10-90%
Life Span
Printer Head service
lifetime
15,000,000 lines (100km)
Auto-cutter 1,000,000cuts
MCBF 60,000,000 lines
Physical
Characteristics
Dimensions (W x D x H)
5.75" x 7.75" x 5.88"
(146mm x 197mm x 149mm)
Weight 3.4lb (1.54kg)
Note: Printer speed changes as the as the combination of the data
transmission speed and control command varies.
Power light
-
Turns on
when connected to
power.
Error light - Turns on under the following conditions:
1. Printer overheats
2. Receipt Paper Low
3. Paper cover and/or cutter replacement error
Low Receipt Paper Light - Turns on when the receipt
paper roll is low and/or wrong placement.
Feed key
-
Press feed key to
feed a length of paper.
Loading...