Bello WAVS-320 Owners manual

WAVS-320 Real Wood Audio Video Cabinet

ASSEMBLY INSTRUCTIONS

PATENT PENDING

THE REAL HARDWOODS USED IN BELL'O FURNITURE ARE NATURALLY

BEAUTIFUL. SOME DIFFERENCES IN WOOD GRAIN ARE DESIRABLE

AND EXPECTED. PLEASE USE ONLY HIGH QUALITY WOOD FURNITURE

POLISH

O CARE FOR YOUR CABINET.

T

PARTS LIST

PART DESCRIPTION QUANTITY

A. CABINET TOP 1 PC

B. LEFT SIDE SUPPORT PANEL

RIGHT SIDE SUPPORT PANEL

C.

D. UPPER CABINET SUPPORT FRAME

E. DIVIDER 1 PC

F. BOTTOM SHELF 1 PC

1 PC

1 PC

1 PC

G. BACK PANEL 1 PC

H. DRAWER SIDE PANEL 4 PCS

I. DRAWER BACK PANEL 2 PCS

PARTS LIST (Continued)

PART DESCRIPTION QUANTITY

J. DRAWER FRONT PANEL 2 PCS

K. DRAWER BOTTOM PANEL 2 PCS

L. MIDDLE SHELF 1 PC

M. DOOR FRAME 2 PCS

N. OPTIONAL CLOTH DOOR INSERT

O. OPTIONAL WOOD DOOR INSERT

1. CAM LOCK PIN 18 PCS

2. CAM LOCK 18 PCS

3. DOWEL 16 PCS

2 PCS

2 PCS

4. 03x12mm SCREW 17 PCS

PARTS LIST (Continued)

ART DESCRIPTION QUANTITY

P

5. 04x1" SCREW 16 PCS

6. 05/32"x22mm SCREW 4 PCS

7. DOOR KNOB 4 PCS

8. SHELF SUPPORT PIN 4 PCS

9. DRAWER STOP 2 PCS

10. 03.5x15mm SCREW 16 PCS

11. DOOR HINGE 4 PCS

FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS:

! ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT.

! BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE SHELVES AND DOORS HAVE BEEN

INSTALLED, AND/OR WHEN THERE IS EQUIPMENT LOCATED ON OR IN THE FURNITURE AS THIS MAY CAUSE
THE SHELVES AND OTHER ITEMS TO BECOME UNSECURED AND FALL.

! WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT, SOLID AND LEVEL SURFACE.

! DO NOT

! DO NOT

! DO NOT

! DO NOT PLACE ITEMS ON THE SHELVES WHICH EXCEED THE MAXIMUM WEIGHT LIMITS OF 200 LBS. FOR TOP SHELF

AND 50 LBS. FOR EACH LOWER SHELF

LEAN ON

CLIMB OR STEP

BANG OR PLACE YOUR OWN WEIGHT ON THE DOORS.

THE TV WHEN IT IS ON THE TV STAND.

AND.

THE ST

ON

ASSEMBLY INSTRUCTIONS

NOTE: 2 PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS FURNITURE. THIS TABLE IS

CONSTRUCTED WITH REAL WOOD VENEER. TO AVOID DAMAGE DURING ASSEMBLY, IT
SHOULD BE ASSEMBLED ON A SOFT SURFACE.

Fig. 1

E

2

1

2

D

3

1

1. PLACE the upper cabinet support frame (D) on a soft surface as shown in Fig.1.

INSERT two cam lock pins (1), and two dowels (3) into the center cross frame.
INSERT two cam locks (2) into the divider (E). PLACE the divider over the cam lock
pins and dowels and SECURE them together by turning the cam locks to tighten.

Fig. 2

E

D

2

1

B

1

3

2. PLACE the left side panel support panel (B) on a soft surface. SCREW two cam lock pins (1)
and insert two dowels (3) into the side support panel as shown in Fig. 2. INSERT two cam locks
into the underside of the upper cabinet support frame (D), as shown.
upper cabinet support frame over the cam lock pins and dowels and

PLACE the edge of the

SECURE them together by

turning the cam locks to tighten.

Fig. 3

D

F

2

1

3

B

3. PLACEthe upper cabinet support frame (D) and side support panel (B) assembly upright on
a soft surface.

SCREW three cam lock pins (1) and two dowels (3) into the side panel as
shown in Fig. 3. INSERT three cam locks (2) into the underside of the bottom shelf (F), as
shown.

PLACEthe edge of the bottom shelf over the cam lock pins and dowels and

SECURE them by turning the cam locks to tighten.

Fig. 4

C

1

3

1

2

F

3

2

D

B

4. PLACE three cam lock pins (1), two dowels (3), and three cam locks (2) into the open end of
the bottom shelf (F) as shown in Fig. 4. PLACE two cam locks into the holes in the open end
of the upper cabinet support frame (D) as shown.
over the cam lock pins and dowels and

SECURE them together by turning all cam locks to

PLACE the right side support panel (C)

tighten.

Fig. 5

A

3

1

1

3

1

B

3

E

2

C

8

5. SCREW six cam lock pins (1) and insert six dowels (3) into the underside of the top panel
(A) as shown in Fig. 5. INSER
into the side of the divider

T

two cam locks (2) into the inside top of each side panel and

. INSER

T

two shelf support pins (8) into each of the adjustable
shelf holes on the inside of each side panel (B & C). CAREFULLY PLACE the cabinet top
panel (A) onto the cam pins and dowels, and GENTLY push down on the top panel until it
is flush with all support panels.

SECURE the top panel to the cabinet by turning all cam

locks to tighten.

Fig. 6

G

4

6. Working from the rear of the cabinet, ALIGN the back panel (G) as shown in Fig. 6, and

SECURE the panel to the rear of the cabinet with screws (4).

Fig. 7

K

I

J

9

4

H

5

6

7

5

H

7. ATTACH the drawer stop (9) to the underside of each drawer back panel (I) using one screw (4)
as shown in Fig. 7.
ALIGN the LEFT

drawer side (H) with the edges of the drawer rear and front panels and

A

the door knob (7) to each drawer front (J) using one screw (6).

CH

A

TT

SECURE with four screws (5). TIP the drawer on its side, and slide the drawer bottom panel (K)

into the grooves until flush. ALIGN the RIGHT drawer side (H) with the edges of the drawer rear
and front panels and

SECURE with four screws (5).

Fig. 8

8. ALIGN the drawers with the drawer slides, and INSERT them into the cabinet.

Fig. 9

8

L

9. SLIDE the middle shelf (L) into place with the CMS®(Cable Management System) slot facing
the rear as shown if Fig. 9, making sure that it is supported evenly by all four of the shelf
support pins (8).

10. ATTACH the door hinges (11) to the inside of the cabinet and to the door frame (M) using
screws (10) as shown in Fig. 10. ATTACH the door knobs (7) to the doors using screws (6).

Fig. 10

11

M

7

1.

10

6

M

7

2.

3.

This cabinet comes with 3 sets of door panel inserts (glass, solid wood, and speaker cloth) that can
be used. To interchange any of the door panel inserts, CAREFULLY REMOVE the rubber gasket
that is used to secure the panel inside the door frame. TO AVOID DAMAGE TO THE DOORS DO
NOT USE ANY SHARP TOOLS TO REMOVE THE GASKET. REMOVE the panel. PLACE the
desired panel insert into the door frame. INSERT the edge of the rubber gasket along the edge of

press down along the length of the gasket to secure it in place.

the panel insert and GENTL

Y

Fig. 11:
Aligning the Doors

11. ALIGN the doors by adjusting the screws on the insides of each hinge (1
screwdriver tool as shown.

1) using the supplied

Warranty

One (1) Year Limited Warranty

All Bell’O International products are warranted, with the exception of glass, to the original purchaser at the time of
purchase and for a period of one (1) year thereafter. Glass is warranted to the original purchaser at the time of
purchase and for a period of thirty (30) days thereafter. Warranty is only valid in the United States of America.

In order to provide you with timely assistance, please thoroughly inspect your furniture for missing or defective parts
immediately after opening the carton. To receive replacement or missing part(s) under this warranty, go to our
website at www.bello.com or call our Customer Service Department at 1-888-235-7646. Please have the model
number and part number(s) for reference. You will also need your sales receipt or other proof of purchase.
Replacement part(s) will be shipped to you at no charge with Bell’O International assuming all shipping and handling
expense.

We warrant to you, the original purchaser, that our furniture and all of its parts and components are free of defects in
material or workmanship. "Defects", as used in this warranty, is defined as any imperfections that impair the use of
the furniture or product.

Our warranty is expressly limited to the replacement of furniture parts and components. For one (1) year after the
date of purchase, Bell’O International will replace any part described on the enclosed furniture parts list that is
defective in material or workmanship.

This warranty applies under conditions of normal use. Our furniture products are not intended for outdoor use. The
warranty does not cover: 1) defects caused by improper assembly or disassembly; 2) defects caused by shipping,
claims for damage during transit to you should be placed immediately by you to the transportation company;

3) defects occurring after purchase due to product modification, intentional damage, accident, misuse, abuse,
negligence or exposure to the elements; 4) cosmetic damage and 5) labor or assembly costs.

There are no warranties, express or implied, including without limitation merchantability or fitness for particular use,
except as (i) contained herein or (ii) required by applicable law in the state whose law governs (which shall be New
Jersey absent controlling law imposing the law of another state in lieu thereof as governing law). All warranties of
whatsoever derivation shall be limited to the term set forth above, unless otherwise required by applicable law.

Manufacturer’s employees or representatives’ … ORAL OR OTHER WRITTEN STATEMENTS DO NOT CONSTITUTE
WARRANTIES, shall not be relied upon by Buyer, and are not a part of the contract for sale or this limited warranty.

Except as provided herein, Bell’O International shall have no liability or responsibility to the purchaser or any other
person or entity with respect to any liability, loss or damage caused directly or indirectly by use of the product,
including, but not limited to, any incidental or consequential damages. Some states do not allow limitation on how
long an implied warranty can last or the exclusion of limitation of incidental or consequential damages, so the above
limitation and exclusion may not apply to you.

This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.

BELL'O INTERNATIONAL CORPORATION, 711 Ginesi Drive, Morganville, NJ 07751-1235

Phone: [phone] Fax: [phone] Web: www.bello.com E-mail: [e-mail]