Belling IWM7KG User Manual
IWM7KG
Washing Machine
User’s Manual
2
EN
Please read this user manual first!
Dear Customer,
We hope that you get the best results from the product which has been manufactured
in state-of-the-art plants and passed through a strict quality control procedure.
Therefore, please read the entire user manual carefully before using the product and
keep it as a reference for future use. In case of transferring the product to someone
else, give the manual as well.
The user manual will help you use your machine in a
fast and safe way.
• Read the user manual before installing and starting your product.
• Always follow the safety instructions.
• Keep this user manual within easy reach for future reference.
• Read also the other documents supplied with the product.
Remember that this user manual is also applicable for several other models.
Differences between models will be identified in the manual.
Explanation of symbols
Throughout this user manual the following symbols are used:
C Important information or useful hints about usage.
A Warning for hazardous situations with regard to life and property.
B Warning for electric shock.
This appliance’s packaging material is recyclable. Help recycle it and protect
the environment by dropping it off in the municipal receptacles provided
for this purpose. Your appliance also contains a great amount of recyclable
material. It is marked with this label to indicate the used appliances that
should not be mixed with other waste. This way, the appliance recycling
organised by your manufacturer will be done under the best possible
conditions, in compliance with European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment. Contact your town hall or your retailer
for the used appliance collection points closest to your home. We thank you
doing your part to protect the environment.
2820522035_EN/070411.0837
3
EN
TABLE OF CONTENTS
1 Your washing machine 4
Overview . . . . . . . . . . . . . . . . . . . . . . . 4
Technical specifications . . . . . . . . . . . . 5
2 Warnings 6
General Safety. . . . . . . . . . . . . . . . . . . 6
First Use . . . . . . . . . . . . . . . . . . . . . . . 6
Intended use . . . . . . . . . . . . . . . . . . . . 6
Safety instructions . . . . . . . . . . . . . . . . 7
If there are children in your house... . . . 7
3 Installation 8
Appropriate installation location . . . . . . 8
Removing packaging reinforcement. . . 8
Removing the transportation locks. . . . 8
Connecting water supply . . . . . . . . . . . 9
Connecting to the drain . . . . . . . . . . . . 9
Adjusting the feet. . . . . . . . . . . . . . . . 10
Raising the appliance. . . . . . . . . . . . . 10
Electrical connection . . . . . . . . . . . . . 11
First use . . . . . . . . . . . . . . . . . . . . . . 12
Disposing of packaging material . . . . 12
Transportation of the product. . . . . . . 12
Disposing of the old product . . . . . . . 12
4 Preparation 13
Things to be done for energy saving . 13
Sorting the laundry . . . . . . . . . . . . . . 13
Preparing laundry for washing . . . . . . 13
Correct load capacity . . . . . . . . . . . . 14
Loading the laundry. . . . . . . . . . . . . .14
Detergents and softeners . . . . . . . . . 15
Tips for efficient washing . . . . . . . . . . 17
5 Operating the product 18
Control panel. . . . . . . . . . . . . . . . . . . 18
Display symbols. . . . . . . . . . . . . . . . . 18
Preparing the machine. . . . . . . . . . . . 19
Programme selection. . . . . . . . . . . . . 19
Main programmes . . . . . . . . . . . . . . 19
Additional programmes . . . . . . . . . . . 19
Temperature selection . . . . . . . . . . . . 20
Spin speed selection . . . . . . . . . . . . .21
Programme and consumption table. . 22
Auxiliary function selection . . . . . . . . .23
Time display . . . . . . . . . . . . . . . . . . . 24
Starting the programme. . . . . . . . . . . 24
Progress of programme . . . . . . . . . . . 24
Loading door lock . . . . . . . . . . . . . . . 25
Changing the selections after programme
has started . . . . . . . . . . . . . . . . . . . . 25
Child Lock . . . . . . . . . . . . . . . . . . . . . 25
Canceling the programme . . . . . . . . . 26
Machine is in Rinse Hold mode . . . . . 26
End of programme . . . . . . . . . . . . . . 26
6 Maintenance and
cleaning 27
Cleaning the detergent drawer. . . . . . 27
Cleaning the loading door and the
drum . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning the body and control panel . 27
Cleaning the water intake filters . . . . .28
Draining remaining water and cleaning the
pump filter . . . . . . . . . . . . . . . . . . . . . 28
7 Troubleshooting 30
8 BUILT-IN INSTALLATION 36
4
EN
1 Your washing machine
Overview
3
4
5
2
1
6
7
8
1- Power cable
2- Top lid
3- Control panel
4- Filter cap
5- Adjustable feet
6- Loading door
7- Detergent drawer
8- Drain hose
5
EN
IWM7KG
7
82
60
54
71
230 V / 50Hz
10
2200
1200
1.40
0.20
Models
Maximum dry laundry capacity (kg)
Height (cm)
Width (cm)
Depth (cm)
Net weight (±4 kg.)
Electrical input (V/Hz)
Total current (A)
Total power (W)
Spin speed (rpm max.)
Stand-by mode power (W)
Off-mode power (W)
Technical specifications
C
Technical specifications may be changed without prior notice to improve the quality of
the product.
C
Figures in this manual are schematic and may not match the product exactly.
C
Values stated on the product labels or in the documentation accompanying it
are obtained in laboratory conditions in accordance with the relevant standards.
Depending on operational and environmental conditions of the product, these values
may vary.
6
EN
2 Warnings
Please read the following information.
Otherwise, there may be the risk of
personal injury or material damage.
Moreover, any warranty and reliability
commitment will become void.
General Safety
• Never place your machine on a
carpet covered floor. Otherwise,
lack of airflow from below of your
machine may cause electrical parts to
overheat. This may cause problems
with your washing machine.
• If the power cable or mains plug is
damaged you must call Authorized
Service for repair.
• Check water hoses for wear. Do not
use old/used water inlet hoses. These
may cause stains on your laundry.
• Fit the drain hose into the discharge
housing securely to prevent any water
leakage and to allow machine to take
in and discharge water as required.
It is very important that the water
intake and drain hoses are not folded,
squeezed, or broken when the
appliance is pushed into place after it
is installed or cleaned.
• Your washing machine is designed to
continue operating in the event of a
power interruption. You cannot cancel
any program by pressing the “On/Off
button.” Your machine will not resume
its program when the power restores.
Press the “Start/Pause/Cancel”
button for 3 seconds to cancel the
program (See, Cancelling a Program)
• There may be some water in your
machine when you receive it. This is
from the quality control process and
is normal. It is not harmful to your
machine.
• Some problems you may encounter
may be caused by the software.
Press “Start/Pause/Cancel” button
for 3 seconds to cancel the program
set in your machine before calling the
authorized service.
First Use
• To prepare your machine for washing,
carry out your first washing process
without loading your machine and
with detergent under “Cottons 90°C”
program.
• Ensure that the cold and hot water
connections has been made correctly
when installing your machine.
Otherwise, your laundry may come
out hot at the end of the washing
process and may wear out.
• If the current fuse or circuit breaker is
less than 16 Amperes, please have
a qualified electrician install a 16
Ampere fuse or circuit breaker.
• While using with or without a
transformer, do not neglect to have
the grounding installation laid by a
qualified electrician. Our company
shall not be liable for any damages
that may arise when the machine is
used on a line without grounding.
• To make your machine ready for use,
please be sure that the tap water
supply and water drainage systems
are appropriate before calling the
authorized service. If they are not,
call a qualified plumber to have any
necessary arrangements carried out.
Intended use
• This product has been designed for
home use.
• The appliance may only be used for
washing and rinsing of textiles that
are marked accordingly.
• Only detergents, softeners and
supplements suitable for washing
machines may be used.
• Observe the care instructions labelled
on textile products and any other
instructions given by companies that
produce detergents for your machine.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
7
EN
concerning use of the appliance by a
person responsible for their safety.
Safety instructions
• This appliance must be connected to
an earthed outlet protected by a fuse
of suitable capacity.
• The supply and draining hoses must
always be securely fastened and
remain in an undamaged state.
• Fit the draining hose to a washbasin
or bathtub securely before starting up
your machine. There may be a risk of
being scalded due to high washing
temperatures!
• Never open the door or remove the
filter while there is still water in the
drum. Otherwise, there may be the
risk of flooding and possible injury
due to the hot water.
• Never force open the locked door!
The door will be ready to open just a
few minutes after the washing cycle
comes to an end.
• Unplug the machine when it is not in
use.
• Never wash down the appliance
with a water hose! There is the risk
of electric shock! Always disconnect
from the mains by unplugging before
cleaning.
• Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out from the plug only. Do
not operate the machine if the power
cord or plug is damaged.
• Never attempt to repair the machine
yourself. Otherwise, you may be
putting yours and other’s lives in
danger.
• For malfunctions that cannot be
solved by information in the operating
manual:
Turn off the machine, unplug it, turn
off the water tap and contact an
authorized service agent.
If there are children
in your house...
• Electrical appliances may be
dangerous for the children. Keep
children away from the machine when
it is operating. Do not let them tamper
with the machine.
• Close the door when you leave the
area where the machine is located.
• Store all detergents in a safe place out
of reach of the children.
8
EN
3 Installation
Refer to the nearest Authorised Service
Agent for installation of the product. To
make the product ready for use, review
the information in the user manual and
make sure that the electricity, tap water
supply and water drainage systems are
appropriate before calling the Authorized
Service Agent. If they are not, call a
qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparation of the location and
electrical, tap water and waste water
installations at the place of installation
is under customer's responsibility.
B
Installation and electrical connections
of the product must be carried out
by the Authorized Service Agent.
Manufacturer shall not be held
liable for damages that may arise
from procedures carried out by
unauthorized persons.
A
Prior to installation, visually check if
the product has any defects on it. If
so, do not have it installed. Damaged
products cause risks for your safety.
C
Make sure that the water inlet and
discharge hoses as well as the power
cable are not folded, pinched or
crushed while pushing the product
into its place after installation or
cleaning procedures.
Appropriate installation location
• Place the machine on a rigid floor.
Do not place it on a long pile rug or
similar surfaces.
• Total weight of the washing machine
and the dryer -with full load- when
they are placed on top of each other
reaches to approx. 180 kilograms.
Place the product on a solid and flat
floor that has sufficient load carrying
capacity!
• Do not place the product on the
power cable.
• Do not install the product at places
where temperature may fall below
0ºC.
• Place the product at least 1 cm away
from the edges of other furniture.
Removing packaging
reinforcement
Tilt the machine backwards to remove
the packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
Removing the
transportation locks
A
Do not remove the transportation
locks before taking out the packaging
reinforcement.
A
Remove the transportation safety
bolts before operating the washing
machine, otherwise, the product will
be damaged.
1. Loosen all the bolts with a spanner
until they rotate freely (C).
2. Remove transportation safety bolts
by turning them gently.
9
EN
3. Attach the plastic covers supplied in
the User Manual bag into the holes
on the rear panel. (P)
C
Keep the transportation safety bolts
in a safe place to reuse when the
washing machine needs to be moved
again in the future.
C
Never move the product without the
transportation safety bolts properly
fixed in place!
Connecting water supply
C
The water supply pressure required
to run the product is between 1 to 10
bars (0.1 – 10 MPa). It is necessary
to have 10 – 80 liters of water flowing
from the fully open tap in one minute
to have your machine run smoothly.
Attach a pressure reducing valve if
water pressure is higher.
C
If you are going to use the double
water-inlet product as a single (cold)
water-inlet unit, you must install the
supplied stopper to the hot water
valve before operating the product.
(Applies for the products supplied
with a blind stopper group.)
C
If you want to use both water inlets
of the product, connect the hot water
hose after removing the stopper and
gasket group from the hot water
valve. (Applies for the products
supplied with a blind stopper group.)
A
Models with a single water inlet
should not be connected to the hot
water tap. In such a case the laundry
will get damaged or the product will
switch to protection mode and will
not operate.
A
Do not use old or used water inlet
hoses on the new product. It may
cause stains on your laundry.
1. Connect the special hoses supplied
with the product to the water inlets
on the product. Red hose (left) (max.
90 ºC) is for hot water inlet, blue hose
(right) (max. 25 ºC) is for cold water
inlet.
A
Ensure that the cold and hot water
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end
of the washing process and wear out.
2. Tighten all hose nuts by hand. Never
use a wrench when tightening the
nuts.
3. Open the taps completely after
making the hose connection to check
for water leaks at the connection
points. If any leaks occur, turn off the
tap and remove the nut. Retighten
the nut carefully after checking the
seal. To prevent water leakages and
damages caused by them, keep the
taps closed when the machine is not
in use.
Connecting to the drain
• The end of the drain hose must be
directly connected to the wastewater
drain or to the washbasin.
A
Your house will be flooded if the
hose comes out of its housing
during water discharge. Moreover,
there is risk of scalding due to high
washing temperatures! To prevent
such situations and to ensure smooth
water intake and discharge of the
machine, fix the end of the discharge
hose tightly so that it cannot come
out.
10
EN
• The hose should be attached to a
height of at least 40 cm, and 100 cm
at most.
• In case the hose is elevated after
laying it on the floor level or close
to the ground (less than 40 cm
above the ground), water discharge
becomes more difficult and the
laundry may come out excessively
wet. Therefore, follow the heights
described in the figure.
• To prevent flowing of dirty water back
into the machine and to allow for easy
discharge, do not immerse the hose
end into the dirty water or drive it in
the drain more than 15 cm. If it is too
long, cut it short.
• The end of the hose should not be
bent, it should not be stepped on
and the hose must not be pinched
between the drain and the machine.
• If the length of the hose is too short,
use it by adding an original extension
hose. Length of the hose may not
be longer than 3.2 m. To avoid water
leak failures, the connection between
the extension hose and the drain
hose of the product must be fitted
well with an appropriate clamp as not
to come off and leak.
Adjusting the feet
A
In order to ensure that the product
operates more silent and vibrationfree, it must stand level and balanced
on its feet. Balance the machine by
adjusting the feet. Otherwise, the
product may move from its place
and cause crushing and vibration
problems.
1. Loosen the lock nuts on the feet by
hand.
2. Adjust the feet until the product
stands level and balanced.
3. Tighten all lock nuts again by hand.
A
Do not use any tools to loosen the
lock nuts. Otherwise, they will get
damaged.
Raising the appliance
In order to raise the appliance to eliminate
the gap below the worktop, you will need
to order special optional kit.
Built-in installation section.
Without optional
raising feet.
Gap
With optional raising
feet. Minimum
height=55 mm, max
height=65mm
Service Ref. No. 1493
11
EN
Electrical connection
Connect the product to a grounded outlet
protected by a fuse complying with the
values in the "Technical specifications"
table. Our company shall not be liable
for any damages that will arise when the
product is used without grounding in
accordance with the local regulations.
• Connection must comply with
national regulations.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or
breaker protection are specified in
the “Technical specifications” section.
If the current value of the fuse or
breaker in the house is less than 13
Amps, have a qualified electrician
install a 13 Amp fuse.
• The specified voltage must be equal
to your mains voltage.
• Do not make connections via
extension cables or multi-plugs.
B
Damaged power cables must be
replaced by the Authorized Service
Agents.
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket in a
readily accessible position.
Should the mains lead of the appliance
become damaged or need replacing at
any time, it must be replaced by a special
purpose made mains lead which can only
be obtained from a Authorised Service
Agent.
B
This appliance must be earthed
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as
a plug with a bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse
need to be replaced an ASTA approved
BS1362 fuse of the same rating must
be used. Do not forget to refit the fuse
cover. In the event of losing the fuse
cover, the plug must not be used until a
replacement fuse cover has been fitted.
Colour of the replacement fuse cover
must be the same colour as that visible
on the pin face of the plug. Fuse covers
are available from any good electrical
store.
Important
Fitting a different plug
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying
the terminals on your plug, proceed as
follows:
1 Connect the green - yellow or green
(earth) wire to the terminal in the plug
marked ‘E’ or with the symbol f or
coloured green and yellow or green.
2 Connect the blue (neutral) wire to the
terminal in the plug marked ‘N’ or
coloured black.
3 Connect the brown (live) wire to the
terminal in the plug marked ‘L’ or
coloured red.
With the alternative plugs a 13A fuse must
be fitted either in the plug or adaptor or in the
main fuse box. If in doubt contact a qualified
electrician.
12
EN
First use
Before starting to use the product, make
sure that all preparations are made in
accordance with the instructions in
sections "Important safety instructions"
and "Installation".
To prepare the product for washing
laundry, perform first operation in
Drum Cleaning programme. If your
machine is not featured with Drum
Cleaning programme, use Cottons-90
programme and select Additional Water
or Extra Rinse auxiliary functions as
well. Before starting the programme,
put max. 100 g of powder antilimescale into the main wash detergent
compartment (compartment nr. II). If
the anti-limescale is in tablet form, put
only one tablet into compartment nr. II.
Dry the inside of the bellow with a clean
piece of cloth after the programme has
come to an end.
C
Use an anti-limescale suitable for
the washing machines.
C
Some water might have remained
in the product due to the quality
control processes in the production.
It is not harmful for the product.
Disposing of packaging
material
Packaging materials are dangerous to
children. Keep packaging materials in
a safe place away from reach of the
children.
Packaging materials of the product are
manufactured from recyclable materials.
Dispose of them properly and sort
in accordance with recycled waste
instructions. Do not dispose of them
with normal domestic waste.
Transportation of the product
1. Unplug the product before
transporting it.
2. Remove water drain and water
supply connections.
3. Drain the remaining water in the
product completely; see, "Draining
remaining water and cleaning the
pump filter".
4. Install transportation safety bolts
in the reverse order of removal
procedure; see, "Removing the
transportation locks".
C
Never move the product without the
transportation safety bolts properly
fixed in place!
Disposing of the old product
Dispose of the old product in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn
how to dispose of your product.
For children's safety, cut the power
cable and break the locking mechanism
of the loading door so that it will be
nonfunctional before disposing of the
product.
13
EN
4 Preparation
Things to be done for
energy saving
Following information will help you use
the product in an ecological and energyefficient manner.
• Operate the product in the highest
capacity allowed by the programme
you have selected, but do not
overload; see, "Programme and
consumption table".
• Always follow the instructions on the
detergent packaging.
• Wash slightly soiled laundry at low
temperatures.
• Use faster programmes for small
quantities of lightly soiled laundry.
• Do not use prewash and high
temperatures for laundry that is not
heavily soiled or stained.
• If you plan to dry your laundry in a
dryer, select the highest spin speed
recommended during washing
process.
• Do not use detergent in excess of
the amount recommended on the
detergent package.
Sorting the laundry
• Sort laundry according to type of
fabric, colour, and degree of soiling
and allowable water temperature.
• Always obey the instructions given on
the garment tags.
Washing water
temperature
Bleach can be
used
Suitable for drier
Wash with sensitive,
.short programmes
Do not use bleach
Do not dry with drier
Hang without
spinning
Can be ironed with
hot iron
Non machine-washable Do not wash
Dry-cleanable Do not dry-clean
Dry horizontally Dry on a hanger
Can be ironed
with warm iron
Do not iron
Preparing laundry for washing
• Laundry items with metal
attachments such as, underwired
bras, belt buckles or metal buttons
will damage the machine. Remove
the metal pieces or wash the clothes
by putting them in a laundry bag or
pillow case.
14
EN
• Take out all substances in the
pockets such as coins, pens and
paper clips, and turn pockets inside
out and brush. Such objects may
damage the product or cause noise
problem.
• Put small size clothes such as infant's
socks and nylon stockings in a
laundry bag or pillow case.
• Place curtains in without compressing
them. Remove curtain attachment
items.
• Fasten zippers, sew loose buttons
and mend rips and tears.
• Wash “machine washable” or “hand
washable” labeled products only with
an appropriate programme.
• Do not wash colours and whites
together. New, dark coloured cottons
release a lot of dye. Wash them
separately.
• Tough stains must be treated properly
before washing. If unsure, check with
a dry cleaner.
• Use only dyes/colour changers
and limescale removers suitable for
machine wash. Always follow the
instructions on the package.
• Wash trousers and delicate laundry
turned inside out.
• Keep laundry items made of Angora
wool in the freezer for a few hours
before washing. This will reduce
pilling.
• Laundry that are subjected to
materials such as flour, lime dust,
milk powder, etc. intensely must be
shaken off before placing into the
machine. Such dusts and powders
on the laundry may build up on the
inner parts of the machine in time and
can cause damage.
Correct load capacity
The maximum load capacity depends on
the type of laundry, the degree of soiling
and the washing programme desired.
The machine automatically adjusts the
amount of water according to the weight
of the loaded laundry.
A
Follow the information in the
“Programme and consumption
table”. When overloaded, machine's
washing performance will drop.
Moreover, noise and vibration
problems may occur.
Laundry types and their average weights
in the following table are given as
examples.
Laundry type Weight (g)
Bathrobe 1200
Napkin 100
Duvet cover 700
Bed Sheet 500
Pillowcase 200
Tablecloth 250
Towel 200
Hand towel 100
Evening gown 200
Underclothing 100
Men’s overalls 600
Men’s shirt 200
Men’s pajamas 500
Blouses 100
Loading the laundry
• Open the loading door.
• Place laundry items loosely into the
machine.
• Push the loading door to close until
you hear a locking sound. Ensure that
no items are caught in the door.
C
The loading door is locked while a
programme is running. The door
can only be opened a while after the
programme comes to an end.
A
In case of misplacing the laundry,
noise and vibration problems may
occur in the machine.
15
EN
Detergents and softeners
Detergent Drawer
Detergent drawer of your washing
machine consists of four different
compartments for powder main wash
detergent, liquid main wash detergent,
liquid softener and powder pre-wash
detergent. Each of these laundry
additives are dispensed automatically
in the relevant time during the washing
Programme.
Do not place the laundry additives directly
into the drum. Always use the detergent
drawer.
Do not close the drawer too fast after
putting the laundry additives. This may
cause the additives be dispensed early,
creating unsatisfactory washing results
and fabric damage.
C
Do not open the drawer during
washing Programme.
The detergent drawer compartments
are indicated below:
1) Left compartment with number “II”
(Main wash compartment for powder
detergent or powder bleach/stain
remover)
2) Left compartment with number “II
” (Main wash compartment for liquid
detergent or liquid stain remover)
3) Middle compartment with number “I”
(pre-wash compartment for powder
detergent, powder stain remover or
liquid bleach - liquid bleach must be
added either during the pre-wash
or during the first rinsing step of the
washing Programme). Liquid bleach
must be added manually while the
machine takes in water.
4) Right compartment with “
” symbol
(liquid softener compartment)
1
2
3
4
(II) Main Wash Compartment
Before starting the washing Programme,
put powder detergent into the left
compartment with number “II”. Use the
detergent manufacturer’s measuring
cup and follow the instructions on the
package. Powder bleach/stain remover
must also be put into this compartment.
Put the liquid detergent into the main
wash compartment with number “II
”
before starting the washing Programme.
Liquid stain remover must be put into this
compartment.
Put the suggested amount of liquid
detergent into the left compartment with
“II
” symbol and dilute it to the maximum
filling level line (max. II ) with warm
water.
Particularly the concentrated detergents
must be diluted with warm water;
otherwise, the siphon may get clogged in
time.
Do not fill the detergent above the
maximum filling level line; otherwise the
excess amount of detergent will reach
the laundry without water and may cause
stains on the garments.In this case you
will need to refill the compartment. Do
not pour the detergent onto the laundry
directly since this may cause stains on
the garments.
Liquid Softener Compartment
Put the suggested amount of liquid
softener into the right compartment
with “
” symbol and dilute it to the
maximum filling level line (max. )
with warm water.
Loading...