Page 1
BELLSYSTEM PRACTICES SECTION 503-200-110
AT&TCo Standard Issue 1, December 1975
882A200 TELEPHONE SETS
1. GENERAL mounting cord or the 225A adapter furnished with
1.01 This section provides identification, installation,
and connection information for the 882A200 1.04 The 882A200 telephone set is available in
DESIGN LINE* telephone (Coquette)set (Fig. 1). white (-58) only.
*Trademark of AT&T Co. 2. IDENTIFICATION
1.02 Whenever this section is reissued, the reason 2.01 The 882A200 rotary dial equipped set is a
will be listed in this paragraph, new DESIGN LINE telephone set being
Warning: Telephone apparatus or wiring buys the housing and handset from the telephone
shah not be installed in a location where company and the telephone company retains
minimum separation from other wiring ownership of the transmission and signaling
cannot be maintainedasspecit_edin Section components (Fig. 2 and 3).
460-300-149.
each telephone set.
made available to the customer. The customer
Fig. 1m882A200 DESIGN LINE Telephone Set
1.03 The customer's premises must be properly
wired with an appropriate connecting block
or jack in order to accept the D4BU-29 plug ended Fig. 2mCustomer-Owned Components
Not for use or disclosure outside the
Bell System except under written agreement
NOTICE
Printed in U.S.A. Page 1
Page 2
SECTION 503-200- ! 10
2.02 Ordering Guide: 3.05 To gain access to the interior of the set
(a) The Coquette is a modular type white (-58) paragraphs in Part 4.
cradle phone equipped with a rotary dial
and may be ordered as follows: 3.06 Line and Ringer Connections:
for wiring changes, refer to the appropriate
• Set, Telephone, 882A200 (1) For single line and two-party service, refer
This includes:
(1) 882AS200 housing of the P1A ringer, refer to Section 501-259-101.
(2) 880DT-58 telephone unit 4. REMOVAL OF TELEPHONE COMPANY-OWNED
Note: This includes all the components shown
in Fig. 3. 4.01 When it is desired to discontinue telephone
2.03 These telephone sets are intended to be telephone set, proceed as follows:
used as single line or two-party desk sets
and are not recommended for use on four-party Note: Remove the telephone company-owned
eight-party service, components that can be easily removed. Refer
3. INSTALLATIONAND CONNECTIONS (1) Remove the four mounting screws from the
3.01 These telephone sets are furnished from baseplate Fig. 2.
the factory fully assembled and wired for
bridged ringing. To connect the telephone set, (2) Remove components that are mounted to,
plug the mounting cord into a 625-type connecting or held by the baseplate.
block or if an existing 548A jack (or equivalent) is
provided use the 225A adapter furnished with each (3) Remove three dial mounting screws and
set. remove the rotary dial.
3.02 The internal connections for the 882A200 (4) Unscrew transmitter and receiver caps and
telephone set, for nonkey system use, are remove T1 transmitter and LB1 receive units.
shown in Fig. 4.
3.03 Connections for 1A KTS do not require any
telephone set modifications and are wired 4.02 Follow local procedures for returning telephone
same as Fig. 4. company-owned components.
3.04 Wiring modifications and connections for use Electric for repair, it should be packed using
with 1A1 or 1A2 KTS are shown in Table the D-180600 Kit of Parts which contains packing
B and Fig. 5. materials and instructions.
to Table A.
(2) For adjustments and ringer cutoff feature
COMPONENTS
service of the 882A200 DESIGN LINE
to Fig. 3 for identification of company-owned
components.
bottom of telephone set and remove the
(5) Replace baseplate.
4.03 When it is desired to return a set to Western
Page 2
Page 3
ISS 1, SECTION 503-200-110
Fig. 3--Telephone Company-Owned Components
Page 3
Page 4
SECTION 503-200-110
TABLE A
LINE AND RINGER CONNECTIONS (882A200 TELEPHONE SET)t
WIRE OR LEAD COLOR OR
Inside Wire at R R R R R R
Jack G G G G G G
623P4 Line Jack R A A L1 F F
Assy G L1 L_ A L2 L2
Ringer R K K K K K
Line Switch Y A A A L2 L2
• Insulated and stored.
t For access to set wiring follow applicable steps in Part 4.
Y Y Y Y Y Y
BK B B B B B
Y G G G G G
BK L2 L2 L2 * *
S-R * * * * L1
S * * * L1 *
BK L1 G G G G
W F F F B B
MODIFICATIONS FOR 1A1 or 1A2 KTS (882A200
INDIVID. TIP PARTY
BRIDGED PARTY NO IDENT IDENTIFYING GROUND
LEAD COLOR REMOVE CONNECT
Line
Switch
623P4 Line
Jack Assy
Ringer BK L1 F
* For access to telephone set wiring follow applicable
steps in Part 4.
RING
GROUND 1000_, 2650_'_
TABLE B
TELEPHONE SET)*
NETWORK TERMINAL
FROM TO
S A L2
Y A L2
BR C G
G L1 A
W F C
G L1 F
Page 4
Page 5
ISS 1, SECTION 503-200-110
Ib.
i
z
II--
i I
iL ¸ _ ._!ili
iiiimnlllllllmmllm
iii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_ii_
v
•-4 •
o"_ v
o
t
................................................................11111177iiiiii=iiiiii-iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii-iiiiiiiiiiiiiiiiiiii17111111.-17iiii......._......._._!_;.-...................---_ ,,
_" ._.
t:
0
C
u
9.
l
W
.............................................................................................................................................................,_:111--..-----1,_;i -T_P'__-T_+,---
-,ii -_ _ !4 1-4 -"
I I II
474-' ,,:
Page 5
Page 6
SECTION 503-200-110
!
_' Illm
t o
;-I
i Z Z
................................................................................._-- _ _77177ii7_______i.-.-.._.............................. IJll
O 0
1 15 I,-,
O.
! .'J 0
_-_) ---CI --<)--- 9.
u i,,-
|
<,, o o _ I
---- u_ -.-.. |
l#l
0
t
e
o
o
Page 6
6 Pages
Loading...