Belkin F9K1001V5 8820ed01312uk User Manual

Wireless rOUTer

User Manual

N150

F9K1001V5 8820ed01312uk Rev. A00

TABLE OF CONTENTS

Getting Started ...........................................1

What’s in the Box .............................................1

Initial Setup.................................................. 1

How to Set It Up .............................................2

Connect Your Wireless Devices................................20

Additional Capabilities ...................................22

Optional Software ...........................................22

Getting to Know Your Router ..............................23

Technical Details ........................................25

Technical Features ..........................................25

System Requirements........................................ 26

USING YOUR ROUTER....................................27

Enabling Auto Update on Your Belkin Router.....................27

Updating the Router’s Firmware via the Web Interface ............28

Resetting the Router .........................................31

Restoring Your Router to Factory Defaults....................... 31

Restoring the Router to Default Settings Using the Web Interface ...32

Troubleshooting, Support, and Warranty ...................34

Troubleshooting .............................................34

Technical Support ...........................................38

Belkin International, Inc., Limited 2-Year Product Warranty......... 39

Regulatory Information ...................................42

Declaration of Conformity with electromagnetic compatibility and

electromagnetic interference ..................................42

Europe – EU Declaration of Conformity .........................43

General Safety Information: ...................................43

GETTING STARTED

What’s in the Box

N150 Wireless Router Ethernet cable (attached to router) Power supply (attached to router) Quick Setup Guide

Initial Setup

Where to Place Your Router

For the best results, place the Router next to your modem in an open location, away from large metal objects and magnets such as those found in speakers. Raising the Router above floor level can improve the strength of your wireless signal.

GETTING STARTED

How to Set It Up

Connect Your N150 Router

Turn off your modem by disconnecting its power supply. Some modems have a battery backup; this will need to be disconnected at this time as well.

Connect your Router to your modem using the cable (already attached).

Power up your modem by plugging in its power supply. If your modem has a battery backup, it can be reconnected at this time; you may need to hold the reset button for 10 seconds.

Power up your Router by plugging in its power supply.

GETTING STARTED

Network Name (SSID)

Password

Connect to Your Router

The default network ID and password information for your router can be found on the product label on the bottom of the Router.

Use your computer, tablet, or smartphone to connect to the wireless network shown on the router product label.

For information on how to connect your wireless devices, please see the “Connect Your Wireless Devices” section on page 20.

When requested, please enter the password (security key) provided on the card.

When your device has connected to the Router, use a browser to visit http://router/. The router homepage will appear.

GETTING STARTED

If the page does not load, then try visiting http://192.168.2.1 to see the router homepage.

Click the “Detect my connection” button in green. (If you would rather set up the Router manually, click the “set it up manually” link and proceed to page 10.)

After several moments, your Router should automatically detect your Internet connection and restart. This can take anywhere from 30 seconds to 3 minutes depending on your connection type.

If your Router is unable to establish an Internet connection on its own, you may be asked to restart your modem or provide a username and password if your connection requires one. Follow the on-screen instructions provided.

GETTING STARTED

Once your Router is online, it will determine if there is a firmware update available and offer to install it. Please allow up to 5 minutes for the firmware to update.

If there are no updates available, then setup will proceed.

GETTING STARTED

At the next screen you will be invited to change your network name and password. Re-using your previous network name (SSID) and password makes connecting your existing devices to the new router much easier.

If you decide to change these settings, then enter the new values and click “Save and Continue.” (Note: The password must be at least 8 characters long.)

If you changed your network name and password, make note of it on the service card located on the foot of the Router. You will then have to connect to the new network.

GETTING STARTED

Please take this opportunity to register your Router. This will help technical support if there is a problem with your Router.

Simply complete each of the required fields and click “Complete Registration.” If you don’t want to register right now, click “Register Later” to proceed.

GETTING STARTED

At the next screen you can download optional software that was bundled with your Router.

This screen shows you optional software that is available for your Router, such as the Belkin Wi-Fi app used to access your router’s homepage quickly. If you wish to download and install this software program, simply click on the button appropriate for your device.

GETTING STARTED

When finished installing optional software, click “Thanks, take me to the dashboard.”

Congratulations! You are now at your Router’s dashboard. Your Router is set up and ready to use.

Using the WPS Button

1. Start WPS Push Button Connection (WPS PBC) on your

computer or other Wi-Fi device that you would like to connect wirelessly to your Router. Often there will be a button for this purpose in software that came with the device, or a physical “WPS,” “PBC,” or “Security” button on the device itself.

2. Within two minutes, press the WPS button on your Router and hold for two seconds.

The WPS light (small light above WPS button) will blink blue while it listens for your Wi-Fi device. Once a connection is established, the light will turn solid blue and then go out. If a connection is not established, the light will blink amber. You may repeat the process to try again.

You can repeat this process for each WPS-enabled device you’d like to add to your network.

GETTING STARTED

Manually Set Up Your Internet Connection

Use a browser to visit http://router/. You can also try visiting http://192.168.2.1/. The Router’s Welcome page should appear.

Click the “Set it up manually” link. Please select the type of connection your ISP provides. Refer to page 16 for a description of the connection types.

If the selected connection type requires additional information (such as an ISP username and password), the system will ask you for it.

At the next screen you will be invited to change your network name and password. Reusing your previous network name (SSID) and password makes connecting your existing devices to the new router much easier.

GETTING STARTED

If you decide to change these settings, then enter the new values and click “Save and Continue.” (Note: The password must be at least 8 characters long.)

If you changed your network name and password, make note of it on the service card located on the foot of the Router. You will then have to connect to the new network. Please refer to page 20 to do this.

Click “Great, what’s next?”

GETTING STARTED

Please take this opportunity to register your Router. This will help technical support if there is a problem with your Router.

Simply complete each of the required fields and click “Complete Registration.” If you don’t want to register right now, click “Register Later” to proceed.

At the next screen you can download optional software that was bundled with your Router.

+ 32 hidden pages