Belkin F5D8633-4 User Manual

Download

Page 1

N Wireless

Modem Router

User Manual

F5D8633-4

Page 2

Table of Contents

1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . 1

Placement of your N Wireless Modem Router . . . . . . . . . . .

2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. Knowing your Modem Router . . . . . . . . . . . . . . . . . . . . . . . 11

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setup Assistant Software System Requirements. . . . . . . . 11

4. Connecting and Configuring your Modem Router . . . . . . . .

5. Alternate Setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6. Using the Web-Based Advanced User Interface . . . . . . . . . 42

Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Viewing the DHCP Client List Page . . . . . . . . . . . . . . . . . . 45

Configuring the Wireless Network Settings . . . . . . . . . . . . 45

Setting WPA Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Setting WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Using the Access Point Mode . . . . . . . . . . . . . . . . . . . . . . 55

Setting MAC Address Control . . . . . . . . . . . . . . . . . . . . . 56

Configuring the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Using Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Restarting the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7. Manually Configuring Network Settings . . . . . . . . . . . . . . .

8. Recommended Web Browser Settings . . . . . . . . . . . . . . . . .

9. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10. Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

77 82 84

3 8 8

Page 3

Introduction

Thank you for purchasing the Belkin N Wireless Modem Router (the Router). Following are two short sections—the first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance. Please be sure to read through this User Manual completely, and pay special attention to the section entitled “Placement of your Wireless Networking Hardware for Optimal Performance” on the next page. By following our simple setup instructions you will be able to use your Belkin Home Network to:

• Share one high-speed Internet connection with all the computers in your home

• Share resources, such as files and hard drives among all the connected computers in your home

• Share a single printer with the entire family

• Share documents, music, video, and digital pictures

• Store, retrieve, and copy files from one computer to another

• Simultaneously play games online, check Internet email, and chat

Advantages of a Wireless Network

Here are some of the advantages of setting up a Belkin Wireless Network:

• Mobility – you’ll no longer need a dedicated “computer room”—now you can work on a networked laptop or desktop computer anywhere within your wireless range

• Easy installation – Belkin’s Easy Installation Wizard makes setup simple

• Flexibility – set up and access printers, computers, and other networking devices from anywhere in your home

• Easy expansion – the wide range of Belkin networking products let you expand your network to include devices such as printers and gaming consoles

• No cabling required – you can spare the expense and hassle of retrofitting Ethernet cabling throughout the home or office

• Widespread industry acceptance – choose from a wide range of interoperable networking products

section

Page 4

Introduction

Revolutionary N Wireless Technology with MIMO (N MIMO)

Your Belkin N Wireless Modem Router uses a new smart-antenna technology called Multiple Input Multiple Output (MIMO). N MIMO complies with the IEEE draft 802.11n specification. It increases speed, range, reliability, and spectral efficiency for wireless networking systems.

The element that makes Belkin’s N MIMO technology different from a conventional radio is the use of multiple antennas and two simultaneous data streams to deliver wireless transfers around your home or office. A conventional radio uses one antenna to transmit a data stream. Belkin’s N MIMO, on the other hand, uses two antennas. This design helps combat distortion and interference. Belkin’s N MIMO is multidimensional. It builds on one-dimensional smart-antenna technology by simultaneously transmitting two data streams through the same channel, which increases wireless capacity.

Another element that enhances Belkin’s N MIMO is the use of aggregation as specified in the draft 802.11n specification. By shortening the space between packets and combining multiple smaller packets into one larger packet, Belkin’s N MIMO can transmit more data through available bandwidth.

Think of conventional radio transmission as a two-lane highway. The speed limit governs the maximum allowable flow of traffic through that lane. Compared with conventional radios, one-dimensional smart antenna systems help move traffic through that lane faster and more reliably—analogous to a four-lane road on which traffic consistently moves at a rate closer to the speed limit. Belkin’s N MIMO helps traffic move at the speed limit and opens more lanes—to become the superhighway in this example. The rate of traffic flow is multiplied by the number of lanes that are opened.

Page 5

Introduction

Placement of your N Wireless Modem Router

section

Important Factors for Placement and Setup

Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for wireless devices is between 100 and 200 feet.

In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases. This may or may not be noticeable to you. As you move further from your Router, connection speed may decrease. Factors that can weaken signals simply by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls.

If you have concerns about your network’s performance that might be related to range or obstruction factors, try moving the computer to a position between five and 10 feet from the Router in order to see if distance is the problem. If difficulties persist even at close range, please contact Belkin Technical Support.

Note: While some of the items listed below can affect network performance, they will not prohibit your wireless network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this checklist may help.

1. Router Placement

Place your Router, the central connection point of your

network, as close as possible to the center of your wireless network devices.

To achieve the best wireless network coverage for your “wireless

clients” (i.e., computers enabled by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless USB Adapters):

• Ensure that your Router’s networking antennas are parallel

to each other, and are positioned vertically (toward the ceiling). If your Router itself is positioned vertically, point the antennas as much as possible in an upward direction.

• In multistory homes, place the Router on a floor that is as

close to the center of the home as possible. This may mean placing the Router on an upper floor.

• Try not to place the Router near a cordless 2.4GHz phone.

Page 6

Introduction

2. Avoid Obstacles and Interference

Avoid placing your Router near devices that may emit radio “noise,” such as microwave ovens. Dense objects that can inhibit wireless communication include:

• Refrigerators

• Washers and/or dryers

• Metal cabinets

• Large aquariums

• Metallic-based, UV-tinted windows

If your wireless signal seems weak in some spots, make sure that

objects such as these are not blocking the signal’s path (between your computers and Router).

3. Cordless Phones

If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone:

• Try moving cordless phones away from your Router and your wireless-enabled computers.

• Unplug and remove the battery from any cordless phone that operates on the 2.4GHz band (check manufacturer’s information). If this fixes the problem, your phone may be interfering.

• If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless network. For example, change the phone to channel 1 and move your Router to channel 11. See your phone’s user manual for detailed instructions.

• If necessary, consider switching to a 900MHz or 5GHz cordless phone.

Page 7

Introduction

4. Choose the “Quietest” Channel for your Wireless Network

In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours.

section

Use the Site Survey capabilities found in the Wireless Utility of

your wireless adapter to locate any other wireless networks that are available (see your wireless adapter’s user manual), and move your Router and computers to a channel as far away from other networks as possible.

• Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices.

• For Belkin wireless networking products, use the detailed Site Survey and wireless channel information included with your wireless network card. See your network card’s user guide for more information.

These guidelines should allow you to cover the maximum

possible area with your Router. Should you need to cover an even wider area, we suggest the Belkin Wireless Range Extender/Access Point.

Page 8

Introduction

5. Secure Connections, VPNs, and AOL

Secure connections typically require a user name and password, and are used where security is important. Secure connections include:

• Virtual Private Network (VPN) connections, often used to connect remotely to an office network

• The “Bring Your Own Access” program from America Online (AOL), which lets you use AOL through broadband provided by another cable or DSL service

• Most online banking websites

• Many commercial websites that require a user name and password to access your account

Secure connections can be interrupted by a computer’s power

management setting, which causes it to “go to sleep.” The simplest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website.

A second alternative is to change your computer’s power management

settings so it does not go to sleep; however, this may not be appropriate for portable computers. To change your power management setting under Windows, see the “Power Options” item in the Control Panel.

If you continue to have difficulty with Secure Connections, VPNs, and

AOL, please review the steps above to be sure you have addressed these issues.

Page 9

Introduction

Free Tech Support*

You can find additional support information on our website at www. belkin.com through the tech-support area.

If you want to contact technical support by phone, please call the number you need from the list below*.

*Local rates apply.

Country Number Internet adress AUST RIA 0820 200766 BELG IUM 07 07 00 073 CZECH REPUBLIC 239 000 406 DENMARK 701 22 403 FINLAND 00800 - 22 35 54 60 FRANCE 08 - 25 54 00 26 GERMANY 0180 - 500 57 09 GREECE 00800 - 44 14 23 90 HUNGARY 06 - 17 77 49 06 ICELAND 800 8534 IRELAND 0818 55 50 06 ITALY 02 - 69 43 02 51 LUXEMBOURG 34 20 80 85 60

NETHERLANDS

NORWAY 81 50 0287 POLAND 00800 - 441 17 37 PORTUGAL 707 200 676 RUSSIA 495 580 9541 SOUTH AFRICA 0800 - 99 15 21 SPAIN 902 - 02 43 66 SWEDEN 07 - 71 40 04 53 SWITZERLAND 08 - 48 00 02 19 UNITED KINGDOM 0845 - 607 77 87

OTHER COUNTRIES +44 - 1933 35 20 00

0900 - 040 07 90 €0.10 per minute

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/nl/ networ king /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/fr/netw orki ng/

http://www.b elkin.com/de/ networ king /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/it /sup port/ tech/i ssues _more. asp

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/nl/ networ king /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/net working /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/es/ suppor t/tec h/netw orking supp ort.asp

http://www.b elkin.com/se/ suppor t/tec h/netw orki ngsupp ort.as p

http://www.b elkin.com/uk/ networ king/

section

Page 10

Product Overview

Product Features

In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin N Wireless Modem Router an ideal solution for your home or small office network.

Works with Both PCs and Mac® Computers

The Router supports a variety of networking environments including Mac OS® 8.x, 9.x, X v10.x, Linux®, Windows® 98, Me, NT®, 2000, XP, and Vista . All that is needed is an Internet browser and a network adapter that supports TCP/IP (the standard language of the Internet).

Patent-Pending Network Status Display

Lighted LEDs on the front of the Router indicate which functions are in operation. You’ll know at-a-glance whether your Router is connected to the Internet. This feature eliminates the need for advanced software and status-monitoring procedures.

Web-Based Advanced User Interface

You can set up the Router’s advanced functions easily through your web browser, without having to install additional software onto the computer. There are no disks to install or keep track of and, best of all, you can make changes and perform setup functions from any computer on the network quickly and easily.

NAT IP Address Sharing

Your Router employs Network Address Translation (NAT) to share the single IP address assigned to you by your Internet Service Provider while saving the cost of adding additional IP addresses to your Internet service account.

SPI Firewall

Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding.

Page 11

Product Overview

Integrated 10/100 4-Port Switch

The Router has a built-in, four-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of connected devices. The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources.

Universal Plug and Play (UPnP)

UPnP is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant.

Support for VPN Pass-Through

If you connect to your office network from home using a VPN connection, your Router will allow your VPN-equipped computer to pass through the Router and to your office network.

Built-In Dynamic Host Configuration Protocol (DHCP)

Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network. The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup.

Setup Assistant

The Setup Assistant, second generation of Belkin’s renowned Easy Install Wizard, takes the guesswork out of setting up your Router. This automatic software determines your network settings for you and sets up the Router for connection to your Internet Service Provider (ISP). In a matter of minutes, your Router will be up and running on the Internet.

Note: Setup Assistant software is compatible with Windows 2000, XP, Vista and Mac OSX 10.2, 10.3 and 10.4. If you are using another operating system, the Router can beset up using the Alternate Setup Method described in this User Manual (see page 30).

section

Page 12

Product Overview

Integrated N Wireless Access Point

N MIMO is an exciting new wireless technology based on the draft IEEE 802.11n specification. It employs MIMO (Multiple Input Multiple Output) smart-antenna technology that achieves data rates of up to 300Mbps.* Actual throughput is typically lower than the connected data rate and will vary depending on your networking environment.

*NOTE: The standard transmission rate—300Mbps—is the physical data rate. Actual data throughput will be lower.

MAC Address Filtering

For added security, you can set up a list of MAC addresses (unique client identifiers) that are allowed access to your network. Every computer has its own MAC address. Simply enter these MAC addresses into a list using the Web-Based Advanced User Interface and you can control access to your network.

Page 13

Knowing your Modem Router

Package Contents

• Belkin N Wireless Modem Router

• Quick Installation Guide

• Belkin Setup Assistant Software CD

• RJ11 Telephone Cord

• RJ45 Ethernet Networking Cable

• ADSL (Asymmetric Digital Subscriber Line) Microfilter*

• Power Supply

• User Manual in CD *ADSL microfilter varies by country. If it’s not included, you will need

to purchase one.

System Requirements

• An active ADSL service with a telephone wall jack for connecting the Router

• At least one computer with an installed network interface adapter

• TCP/IP networking protocol installed on each computer

• No other DHCP server on your local network assigning IP addresses to computers and devices

• Internet browser

Setup Assistant Software System Requirements

• A computer running Windows 2000, XP, or Vista; or Mac OS X v10.x

• Minimum 1GHz processor and 128MB RAM

• Internet browser

section

1110

Page 14

Knowing your Modem Router

1312

Internet Connection Settings

The Setup Assistant contains a database of Internet Service Providers (ISP) in each country to help you set up your Router quickly. If your ISP is not on the list, please collect the following information from your ISP before setting up the Router:

• Internet connection protocol: (PPPoE, PPPoA, Dynamic IP, Static IP)

• Multiplexing method or Encapsulation: (LLC or VC MUX)

• Virtual circuit: VPI (Virtual Path Identifier) (a number between 0 and 255)

• VCI (Virtual Channel Identifier) (a number between 1 and 65535)

• For PPPoE and PPPoA users: ADSL account user name and password

• For static IP users: IP Address . . . Subnet Mask . . . Default Gateway Server . .

• IP address for Domain Name Server . . . (If given by your ISP)

Page 15

1312

Knowing your Modem Router

The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The Network Status Display is easily visible on the FRONT of the Router to provide you with information about network activity and status. See the Network Status Display Guide for more detailed information.

(E)

(B)

(A)

A. Wireless Security

OFF Wireless security is off Solid Blue Wireless security is on

B. Wireless-Computer Status

OFF Wireless computer is not present Solid Blue Wireless computer is connected to the

Router

Blinking Amber Problem with wireless computer

connecting properly to the Router

(C)

(D)

(F)

section

C. Wired-Computer Status

OFF Wired computer is not present Solid Blue Wired computer is connected to the

Router

Blinking Amber Problem with wired computer connecting

properly to the Router

1312

Page 16

Knowing your Modem Router

1514

D. Router/Power Status

When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. During this time, the “router” icon blinks. When the Router has completely booted up, the “router” icon becomes a solid light, indicating the Router is ready for use.

OFF Router is off Blinking Blue Router is booting up Solid Blue Router is on and ready

E. ADSL Line Status

This icon lights in blue to indicate that your Router is connected properly to the ADSL. It turns amber when problem is detected.

OFF Router is NOT connected to a

Blinking Blue Router is attempting to connect to an

Solid Blue Router is connected to an ADSL service

Blinking Amber Problem with ADSL line

functioning ADSL line

ADSL service

and is functioning properly

Page 17

1514

Knowing your Modem Router

F. Internet Status

This unique icon shows you when the Router is connected to the Internet. When the light is off, the Router is NOT connected to the Internet. When the light is blinking amber, the Router is attempting to connect to the Internet. When the light is solid blue, the Router is connected to the Internet. When using the “Disconnect after x minutes” feature, this icon becomes extremely useful in monitoring the status of your Router’s connection.

OFF Router is NOT connected to the Internet Blinking Blue Router is attempting to connect to the

Solid Blue Router is connected to the Internet Blinking Amber Router is not connected to the Internet

Internet

section

1514

Page 18

Knowing your Modem Router

1716

(G)

G. Connection to ADSL

This port is for connection to your ADSL. Connect your ADSL to this port. An RJ11 telephone cord is provided in the package.

H. Connections to Wired Computers

Connect your wired (non-wireless) computers to these ports. These ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable. The ports are labeled 1 through 4, with onboard LEDs on the connectors.

– Gray

– Yellow

(K)(I)(H) (J)

Page 19

1716

Knowing your Modem Router

I. Reset Button

The “Reset” button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Router’s normal operation while maintaining the programmed settings. You can also restore the factory default settings by using the “Reset” button. Use the restore option in instances where you may have forgotten your custom password.

i. Resetting the Router

Push and release the “Reset” button. The lights on the Router will momentarily flash. The “Power/Ready” light will begin to blink. When the “Power/Ready” light becomes solid again, the reset is complete.

ii. Restoring the Factory Defaults

Press and hold the “Reset” button for at least 10 seconds, then release it. The lights on the Router will momentarily flash. The “Power/Ready” light will begin to blink. When the “Power/Ready” light becomes solid again, the restore is complete.

J. Power Jack – Black

Connect the included 15V/.08A DC power supply to this jack.

K. Push Button – White

This button is set aside for future upgradeable features. Please check for the latest firmware updates at www.belkin.com/ support.

section

1716

Page 20

Connecting and Configuring your Modem Router

1918

Verify the contents of your box. You should have the following:

• Belkin N Wireless Modem Router

• RJ11 Telephone Cord

• RJ45 Ethernet Networking Cable

• Power Supply

• Belkin Setup Assistant Software CD

• User Manual on CD

Setup Assistant

Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task. You can use it to get your Router up and running in minutes. The Setup Assistant requires that your Windows 2000 or XP computer be connected directly to your ADSL and that the Internet connection is active and working at the time of installation. If it is not, you must use the “Alternate Setup Method” section of this User Manual to configure your Router. Additionally, if you are using an operating system other than Windows 2000, XP, or Vista, or Mac OS X v10.x, you must set up the Router using the “Alternate Setup Method” section of this User Manual.

Page 21

1918

Connecting and Configuring your Modem Router

modem router

computer

Step 1

1.1 Brand-New Setup

Hardware Connections – Follow the Quick Installation

Guide (QIG)

Follow these steps if you are not replacing an existing modem. If you are replacing an existing modem, skip to the next section, “Replacing an Existing Modem or Modem Router”, starting on page 20.

A. Unpack your new Router from

the box and place it next to your computer. Raise the Router’s antennas.

B. Retrieve the yellow RJ45 cable that

was included with your Router. First, connect one end to any yellow port labeled “to Wired Computers” on the back of your Router. Then, connect the other end to the networking port on the back of your computer.

section

C. Retrieve the included gray RJ11

phone cord. Connect one end to the gray port labeled “to ADSL” on the back of your Router. Then connect the other end to your ADSL connection (either a wall jack or an ADSL splitter).

Note: Some ADSL connections

require a microfilter. Your ADSL provider can tell you if you need one. Belkin includes a microfilter in regions known to use them. You may or may not have received one in your box.

1918

Page 22

Connecting and Configuring your Modem Router

2120

modem router

computer

D. Plug your Router’s power supply

into the black port labeled “Power” on the back of your Router.

E. Wait 20 seconds for the Router to

start up. Look at the display on the front of the Router. Make sure the “Wired” and “Modem-Router” icons are lit up in blue. If they are not, recheck your connections.

1.2 Replacing an Existing Modem or Modem Router

Follow these steps if you currently have a modem or a modem router that you will be replacing with your new Router.

A. Unpack your new Router from

the box and place it next to your computer. Raise the Router’s antennas.

Page 23

2120

Connecting and Configuring your Modem Router

B. Locate the cable that connects

your old modem to your computer. Unplug that cable from your old modem, and plug it into any yellow port labeled “to Wired Computers” on the back of your new Router.

C. Locate the cable that connects

your old modem to the ADSL wall jack. Unplug it from your old modem and then connect it to the gray port labeled “to ADSL” on the back of your Router.

D. Plug your Router’s power supply

into the black port labeled “Power” on the back of your Router.

E. Wait 20 seconds for the Router to

start up. Look at the display on the front of the Router. Make sure the “Wired” and “Modem-Router” icons are lit in blue. If they are not, recheck your connections.

section

2120

Page 24

Connecting and Configuring your Modem Router

2322

Step 2 Set Up the Router – Run the Setup Assistant Software

A. Shut down any programs that are

running on your computer at this time.

Turn off any firewall or Internet-

connection-sharing software on your computer.

B. Insert the CD into your

computer. The Setup Assistant will automatically appear on your computer’s screen within 15 seconds. Click on “Setup Assistant” to run the Setup Assistant. Follow the instructions there.

IMPORTANT: Run the Setup Assistant from the computer that is directly connected to the Router from Step 1.1B.

Note for Windows Users: If the

Setup Assistant does not start up automatically, select your CDROM drive from “My Computer” and double-click on the file named “SetupAssistant” to start the Setup Assistant.

Page 25

2322

Connecting and Configuring your Modem Router

Select Country

Select your country from the dropdown box. Click “Begin” to continue.

Confirmation Screen

Verify that you have completed all QIG steps by checking the box to the right of the arrow. Click “Next” to continue.

Progress Screen

Setup Assistant will show you a progress screen each time a step in the setup has been completed.

section

2322

Page 26

Connecting and Configuring your Modem Router

2524

2.1 Checking Settings

The Setup Assistant will now examine your computer’s network settings and gather information needed to complete the Router’s connection to the Internet.

2.2 Verifying Hardware Connections

The Setup Assistant will now verify your hardware connection.

2.3 Naming your Wireless Network

The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID). This is the name of your wireless network to which your computers or devices with wireless network adapters will connect. You can either use the default or change it to something unique. Write down this name for future reference.

If the Router is capable of “High

Speed Mode”, this option will be checked. You can turn off this option later using the Bandwidth Switch described in this User Manual (see page 48). Click “Next” to continue.

Page 27

2524

Connecting and Configuring your Modem Router

2.4 Requesting Internet Account

Info (if needed)

Select your ISP from the dropdown boxes.

If your Internet account requires

a login and password, you will be prompted with a screen similar to the illustration below. Click “Next” to continue.

2.5 Configuring the Router

The Setup Assistant will now configure your Router by sending data to the Router and restarting it. Wait for the on-screen instructions.

Note: Do not disconnect any cable

or power off the Router while the Router is rebooting. Doing so will render your Router inoperable.

section

2.6 Checking Internet Connection

We are almost done. The Setup Assistant will now check your connection to the Internet.

2524

Page 28

Connecting and Configuring your Modem Router

2726

Congratulations You have finished installing your new Belkin Router. You will see the Congratulations screen when your Router can connect to the Internet. You can begin surfing by opening your browser and going to any website.

You can use the Setup Assistant to set up your other wired and wireless computers to connect to the Internet by clicking “Next”. If you decide to add computers to your Router later, select “Finish—return to Main Menu” and then click “Next”.

Troubleshooting If the Setup Assistant is not able to connect to the Internet, you will see this screen. Follow the onscreen instructions to go through the troubleshooting steps.

2.7 Optional: Assistance Connecting

Other Computers

This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions.

Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working. You can now surf the Internet. Click “Next” to return to the main menu.

Page 29

2726

Connecting and Configuring your Modem Router

Step 3

Now that your network is set up and working, it is recommended that you turn on wireless security to prevent unauthorized access to your network from neighboring wireless-enabled computers. The Security Assistant will guide you through the process. Click “Security Assistant” and follow the on-screen instructions.

Set Up Wireless Security – Run the Security

Assistant Software

IMPORTANT: Run the Setup Assistant from the computer that is directly connected to the Router from Steps 1.1B and 1.12B.

section

Progress Screen

The Security Assistant will show you a progress screen each time a step has been completed.

2726

Page 30

Connecting and Configuring your Modem Router

2928

3.1 Picking the Security Type

Select the security type for your wireless network and click “Next” to continue.

3.2 Creating a Network Key

Enter a network key (PSK) for your wireless network and click “Next” to continue.

3.3 Transferring the Key

After setting up your wireless security, you will have to transfer the network key to each of your wireless computers. Click on “Transfer Key” if you have a USB flash drive. Follow the onscreen instructions, or click on “Print” to print the information. Manually enter it to each wireless computer. Then, click “Next” to continue.

Page 31

2928

Connecting and Configuring your Modem Router

3.4 Verifying the Connection

If all your wireless computers are able to connect to the Router, click “Next”. If you are having trouble, select “I had problem with at least one computer” and click “Next”. Then, follow onscreen instructions.

Congratulations Once you have verified that your wireless computers are properly connected, your wireless network is set up and secured. You now can run your network wirelessly and securely. Click “Finish” to take you back to the main menu.

section

2928

Page 32

Alternate Setup Method

3130

Step 1

Hardware Connections – Follow the Quick Installation

Guide (QIG)

See the QIG or Step 1: Hardware Connections from the previous section.

Step 2

Set your Computer’s Network Settings to Work with a

DHCP Server

See the section in this User Manual called “Manually Configuring Network Settings” for directions.

Step 3

Configuring the Router Using the Web-Based Advanced

User Interface

Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”). Then press the “Enter” key.

Page 33

3130

Alternate Setup Method

Logging into the Router

You will see the Router’s home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Router’s settings, you have to log in. Clicking the “Login” button or clicking on any one of the links on the home page will take you to the login screen. The Router ships with no password entered. In the login screen, leave the password blank and click the “Submit” button to log in.

Logging out of the Router

One computer at a time can log into the Router for the purposes of making changes to the settings of the Router. Once a user has logged in to make changes, there are two ways that the computer can be logged out. Clicking the “Logout” button will log the computer out. The second method is automatic. The login will time out after a specified period of time. The default login time-out is 10 minutes. This can be changed from one to 99 minutes. For more information, see the section in this manual titled “Changing the Login Time-Out Setting”.

section

Understanding the Web-Based Advanced User Interface

The home page (shown on the next page) is the first page you will see when you access the Advanced User Interface (UI). The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page.

3130

Page 34

Alternate Setup Method

3332

(13) (3) (4) (5)

(6)

(2)

(8)

(7)

(1)

(9)

(10)

(11)

(12)

1. Quick-Navigation Links

You can go directly to any of the Router’s advanced UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find. Clicking on the purple header of each tab will show you a short description of the tab’s function.

2. Home Button

The home button is available in every page of the UI. Pressing this button will take you back to the home page.

3. Help Button

The “Help” button gives you access to the Router’s help pages. Help is also available on many pages by clicking “more info” next to certain sections of each page.

4. Login/Logout Button

This button enables you to log in and out of the Router with the press of one button. When you are logged into the Router, this button will change to read “Logout”. Logging into the Router will take you to a separate login page where you will need to enter a password. When you are logged into the Router, you can make changes to the settings. When you are finished making changes, you can log out of the Router by clicking the “Logout” button. For more information about logging into the Router, see the section called “Logging into the Router”.

Page 35

3332

Alternate Setup Method

5. Internet-Status Indicator

This indicator is visible in all pages of the Router, indicating the connection status of the Router. When the indicator says “Connected” in blue, the Router is connected to the Internet. When the Router is not connected to the Internet, the indicator will read “No Connection” in RED. The indicator is automatically updated when you make changes to the settings of the Router.

6. Connect/Disconnect Buttons

Use these buttons to manually connect or disconnect your ADSL connection as needed.

7. Language

Shows the active language for the Advanced User Interface. Select a desirable language by clicking one of the available languages.

8. Version Info

Shows the firmware version, boot-code version, hardware version, and serial number of the Router.

9. LAN Settings

Shows you the settings of the Local Area Network (LAN) side of the Router. Changes can be made to the settings by clicking on any one of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the “LAN” quicknavigation link on the left side of the screen.

10. Internet Settings

Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the links or by clicking on the “Internet/WAN” quick-navigation link on the left side of the screen.

11. Features

Shows the status of the Router’s NAT, firewall, and wireless features. Changes can be made to the settings by clicking on any one of the links or by clicking the quick-navigation links on the left side of the screen.

12. ADSL Info

Shows the ADSL status and transmission rates.

13. Page Name

The page you are on can be identified by this name. This User Manual will sometimes refer to pages by name. For instance “LAN > LAN Settings” refers to the “LAN Settings” page.

section

3332

Page 36

Alternate Setup Method

3534

Step 4

Configuring your Router for Connection to your Internet

Service Provider (ISP)

The “Internet/WAN” tab is where you will set up your Router to connect to your Internet Service Provider (ISP). The Router is capable of connecting to virtually any ISP’s system provided you have correctly configured the Router’s settings for your ISP’s connection type. Your ISP connection settings are provided to you by your ISP. To configure the Router with the settings that your ISP gave you, click “Connection Type” (A) on the left side of the screen. Select the connection type you use. If your ISP gave you DNS settings, clicking “DNS” (B) allows you to enter DNS address entries for ISPs that require specific settings. Clicking “MAC Address” (C) will let you clone your computer’s MAC address or type in a specific WAN MAC address, if required by your ISP. When you have finished making settings, the “Internet Status” indicator will read “connection OK” if your Router is set up properly.

(A)

(B)

(C)

Page 37

3534

Alternate Setup Method

Connection Type

From the “Connection Type” page, you can select one of these five connection types based on the instruction provided by your ISP:

• PPPoE

• PPPoA

• Dynamic/Fixed IP (1483 Bridged)

• Static IP (IPoA)

• Modem Only (Disable Internet Sharing)

Select the type of connection you use by clicking the radio button (1) next to your connection type and then clicking “Next” (2).

(1)

section

3534

Page 38

Alternate Setup Method

3736

Setting your ISP Connection Type to PPPoE or PPPoA

PPPoE (Point-to-Point Protocol over Ethernet) is the standard method of connecting networked devices. It requires a user name and password to access the network of your ISP for connecting to the Internet. PPPoA (PPP over ATM) is similar to PPPoE, but is mostly implemented in the UK. Select PPPoE or PPPoA and click “Next”. Then enter the information provided by your ISP, and click “Apply Changes” to activate your settings.

(1) (2) (3)

(4) (5) (6)

(7)

1. User Name - Enter the user name. (Assigned by your ISP).

2. Password - Enter your password. (Assigned by your ISP).

3. Retype Password - Confirm the password. (Assigned

by your ISP).

4. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameter here. (Assigned by your ISP).

5. Encapsulation - Select your encapsulation type (supplied by

your ISP) to specify how to handle multiple protocols at the ATM transport layer.

VC-MUX: PPPoA Virtual Circuit Multiplexer (null encapsulation)

allows only one protocol running per virtual circuit with fewer overheads.

LLC: PPPoA Logical Link Control allows multiple protocols running

over one virtual circuit (more overhead).

Page 39

3736

Alternate Setup Method

6. MTU - Enter the MTU value for your ISP.

7. Disconnect after of x minutes of no activity - Checking the box and

enter the number of minute that you want the modem router to auto disconnect after no activity. After this time has been exceeded, the connection will be terminated.

Click “Apply Changes” to save and activate your settings. To go

back to the original settings before saving, click “Clear Changes”. Or click any of the Quick-Navigation links for other options. Your new settings will not be saved unless your click “Apply Changes”.

Setting your Connection Type to Dynamic/Fixed IP (1483 Bridged)

This connection method bridges your network and ISP’s network together. The Router can obtain an IP address automatically from your ISP’s DHCP server or accept a fixed IP address assigned by your ISP.

(1) (2) (3)

(4) (5) (6)

(7)

section

For Dynamic IP connection:

1. VPI/VCI

2. Encapsulation - Select LLC or VC MUX your ISP uses.

Click “Apply Changes” to save and activate your settings. To go

- Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here. These identifiers are assigned by your ISP.

back to the original settings before saving, click “Clear Changes”; or click any of the Quick-Navigation links for other options. Your new settings will not be saved unless you click “Apply Changes”.

3736

Page 40

Alternate Setup Method

3938

(1) (2) (3) (4) (5) (6)

For Dynamic IP connection:

1. IP assigned by ISP

fixed IP.

2. IP Address - Enter an IP address assigned by your ISP for the

Router WAN interface.

3. Subnet Mask - Enter a subnet mask assigned by your ISP.

4. Default Gateway - Enter a default gateway IP address assigned

by your ISP.

5. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameters here. These identifiers are assigned by your ISP.

6. Encapsulation - Select the LLC or VC MUX your ISP uses. Click “Apply Changes” to save and activate your settings. To go

- Select “No” if your ISP instructed you to use

Page 41

3938

Alternate Setup Method

Setting your ISP Connection Type to Static IP (IPoA)

This connection type is also called “Classical IP over ATM” or “CLIP”, which your ISP provides a fixed IP for your Router to connect to the Internet.

(1) (2)

(3) (4) (5)

1. WAN IP Address - Enter an IP address assigned by your ISP for

the Router WAN interface.

2. Subnet Mask - Enter a subnet mask assigned by your ISP.

3. Use Static Default Gateway - Enter a default gateway IP address.

If the Router cannot find the destination address within its local network, it will forward the packets to the default gateway assigned by your ISP.

4. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameter here. These identifiers are assigned by your ISP.

5. Encapsulation - Select LLC or VC MUX your ISP uses.

Click “Apply Changes” to save and activate your settings. To go

section

3938

Page 42

Alternate Setup Method

4140

Setting your Connection Type to Modem Only (Disable Internet Sharing)

In this mode, the Router simply acts as a bridge passing packets across the DSL port. It requires additional software to be installed on your computers in order to access the Internet.

(2) (3)

1. Enable Bridge Service - Check this box to enable bridge service

2. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameters here. (Assigned by your ISP).

3. Encapsulation - Select the LLC or VC MUX your ISP uses.

Click “Apply Changes” to save and activate your settings. To go

Page 43

4140

Alternate Setup Method

Setting Custom Domain Name Server (DNS) Settings

A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locaters (URLs) like “www.belkin. com” to IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address. If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly. If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address. Leave the “Automatic from ISP” box checked. To enter the DNS address settings, uncheck the “Automatic from ISP” box and enter your DNS entries in the spaces provided. Click “Apply Changes”

(2) to save the settings.

(1)

(2)

section

4140

Page 44

Using the Web-Based Advanced User Interface

4342

Using the Web-Based Advanced User Interface

You will see the Router’s home page in your browser window.

Viewing the LAN Settings

Clicking on the header of the LAN tab (1) will take you to the LAN tab’s header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on “LAN Settings” (2) or to view the list of connected computers, click on “DHCP client list” (3).

(1) (2)

(3)

Page 45

4342

Using the Web-Based Advanced User Interface

Changing LAN Settings

All settings for the internal LAN setup of the Router can be viewed and changed here.

(1) (2)

(3) (4)

(5) (6)

1. IP Address

The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click “Apply Changes”. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:

192.168.x.x (where x is anything between 0 and 255)

10.x.x.x (where x is anything between 0 and 255)

2. Subnet Mask

There is no need to change the subnet mask. This is a unique, advanced feature of your Belkin Router. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is “255.255.255.0”.

section

4342

Page 46

Using the Web-Based Advanced User Interface

4544

3. DHCP Server

The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is “On”. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select “Off” and click “Apply Changes”.

4. IP Pool

The range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2–100 (99 computers). If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on “Apply Changes”. The DHCP server can assign 100 IP addresses automatically. This means that you cannot specify an IP address pool larger than 100 computers. For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit. The starting IP address must be lower in number than the ending IP address.

5. Lease Time

The length of time the DHCP server will reserve the IP address for each computer. We recommend that you leave the lease time set to “Forever”. The default setting is “Forever”, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer. Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time. This also means that a particular computer’s IP address may change over time. If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address. For this reason, you will not want the IP address to change.

6. Local Domain Name

The default setting is “Belkin”. You can set a local domain name (network name) for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can name the network anything you want such as “MY NETWORK”.

Page 47

4544

Using the Web-Based Advanced User Interface

Viewing the DHCP Client List Page

You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computer’s network interface card (NIC). Pressing the “Refresh” (4) button will update the list. If there have been any changes, the list will be updated.

(1) (2) (3)

(4)

Configuring the Wireless Network Settings

The “Wireless” tab lets you make changes to the wireless network settings. From this tab you can make changes to the wireless network name or Service Set Identifier (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point.

section

4544

Page 48

Using the Web-Based Advanced User Interface

4746

Changing the Wireless Network Name (SSID)

To identify your wireless network, a name called the SSID is used. The SSID is your network name. The default network name of the Router is “Belkin N Wireless” followed by six digits that are unique to your Router. Your network name will look something like “Belkin_N_ Wireless_123456”. You can change this to anything you choose, or you can leave it unchanged. Keep in mind, if you decide to change your wireless network name, and there are other wireless networks operating in your area, your network name needs to be different from other wireless networks that may be operating in your area. To change the SSID, type in the SSID that you want to use in the SSID field (1) and click “Apply Changes” (2). The change is immediate. If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your new network name. Refer to the documentation of your wireless network adapter for information on making this change.

(1)

(2)

Note: Please periodically check for new Router firmware updates from the “Utilities > Firmware update” page. Newer firmware can fix problems, add wireless features, and/or improve wireless performance (see page 69).

Page 49

4746

Using the Web-Based Advanced User Interface

Changing the Wireless Channel

There are a number of operating channels from which you can choose— in the United Kingdom (and most of Europe) and Australia, there are 13. In other countries, there are other channel requirements. Your Router is configured to operate on the proper channels for the country in which you reside. The channel can be changed if needed. If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks.

Extension Channel

The IEEE 802.11n draft specification allows the use of a secondary channel to double the bandwidth (see the “Using the Bandwidth Switch” section on the next page). An appropriate extension channel will be displayed when operating in 40MHz mode (see the “Using the Wireless Mode Switch” section below). The channel can be changed if necessary.

Using the Wireless Mode Switch

This switch allows you to set the Router’s wireless modes. There are several modes.

Note: Some modes may require firmware updates to be enabled.

1) Off

This mode will turn OFF the Router’s access point, so no wireless devices can join the network. Turning off the wireless function of your Router is a great way to secure your network when you are away from home for a long period of time, or don’t want to use the wireless feature of the Router at a certain time.

2) 802.11g

Setting the Router to this mode will allow only 802.11g- and

802.11b-compliant devices to join the network. N/draft 802.11n devices will operate at the 802.11g speed only.

3) 802.11b & 802.11g & 802.11n

Setting the Router to this mode will allow N/draft 802.11n-,

802.11g-, and 802.11b-compliant devices to join the network.

4) 802.11n

Setting the Router to this mode will allow only N/draft 802.11ncompliant devices to join the network, keeping out 802.11g and

802.11b devices.

section

4746

Page 50

Using the Web-Based Advanced User Interface

4948

Using the Bandwidth Switch

This switch allows you to set the Router’s wireless bandwidth modes. There are several modes available:

1) 20MHz/40MHz

Setting the Router to this mode allows it to switch automatically between 20MHz and 40MHz operation. This mode enables 40MHz operation, to maximize speed for N draft 802.11n-compliant devices when conditions permit. When a legacy 802.11g access point is presented and occupies an adjacent secondary channel, the Router automatically reverts to 20MHz operation to maximize compatibility. Set the Router to this mode for higher performance.

2) 20MHz

Setting the Router to this mode allows only 20MHz operation. This mode is compatible with N, draft 802.11n-, 802.11g-, and 802.11bcompliant devices, but will limit N, draft 802.11n-compliant devices’ bandwidth by half. Reducing bandwidth to 20MHz-only operation might solve some wireless problems. This is the default mode for the Router.

Using the Broadcast SSID Feature

Note: This advanced feature should be employed by advanced users only. For security, you can choose not to broadcast your network’s SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks. To turn off the broadcast of the SSID, remove the check mark from the box next to “Broadcast SSID”, and then click “Apply Changes”. The change is immediate. Each computer now needs to be set to connect to your specific SSID; an SSID of “ANY” will no longer be accepted. Refer to the documentation of your wireless network adapter for information on making this change.

Protected Mode Switch

Protected mode ensures proper operation of N, draft 802.11n-compliant devices on your wireless network when 802.11g or 802.11b devices are present or when there is heavy 802.11g or 802.11b traffic in the operating environment. Use protected mode if your network consists of a mix of Belkin N Wireless Cards and 802.11g or 802.11b cards on your network. If you are in an environment that includes little to no 802.11g or 802.11b wireless network traffic, you will achieve the best N wireless performance with protected mode OFF. Conversely, in an environment with HEAVY 802.11g or 802.11b traffic or interference, you will achieve the best N wireless performance with protected mode ON. This will ensure N wireless performance is not affected.

Page 51

4948

Using the Web-Based Advanced User Interface

802.11e/WMM (Wi-Fi® Multimedia) QoS

WMM, based on 802.11e QoS (Quality of Service), prioritizes important data on your network, such as multimedia content and voice-over-IP (VoIP), so it will not be interfered with by other data being sent over the network. This feature requires other wireless devices, such as Wi-Fi phones or wireless laptops, to support WMM for best results.

Changing the Wireless Security Settings

Your Router is equipped with the latest security standard called WiFi Protected Access 2 (WPA2). It also supports the legacy security standard called Wired Equivalent Privacy (WEP). By default, wireless security is disabled. To enable security, you will need to determine which standard you want to use. To access the security settings, click “Security” on the “Wireless” tab.

The Router features WPA2, which is the second generation of the WPA-based 802.11i standard. It offers a higher level of wireless security by combining advanced network authentication and stronger Advanced Encryption Standard (AES) encryption methods.

WPA2 Requirements

IMPORTANT: In order to use WPA2 security, all your computers and

wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2. At the time of this User Manual’s publication, a couple security patches are available, for free download, from Microsoft®. These patches work only with the Windows XP operating system. Other operating systems are not supported at this time.

For Windows XP computers that do not have Service Pack 2 (SP2), a file from Microsoft called “Windows XP Support Patch for Wireless Protected Access (KB 826942)” is available for free download at http://support.microsoft.com/kb/826942

For Windows XP with Service Pack 2, Microsoft has released a free download to update the wireless client components to support WPA2 (KB971021). The update is available from: http://support.microsoft.com/kb/917021

IMPORTANT: You also need to ensure that all your wireless client

cards/adapters support WPA2, and that you have downloaded and installed the latest driver. Most of the Belkin wireless cards have driver updates available for download from the Belkin support site: www.belkin.com/networking.

section

4948

Page 52

Using the Web-Based Advanced User Interface

5150

Setting WPA/WPA2-Personal (PSK)

Like WPA security, WPA2 is available in both WPA2-Personal (PSK) mode and WPA2-Enterprise (RADIUS) mode. Typically, WPA2Personal (PSK) is the mode that will be used in a home environment, while WPA2-Enterprise (RADIUS) is implemented in a business environment where an external radius server distributes the network key to the clients automatically. This guide will focus on WPA2Personal (PSK) usage. Please refer to the User Manual for more information about wireless security and different types of wireless security.

1. After you’ve set up your Router, go to the “Security” page under

“Wireless” and select “WPA/WPA2-Personal (PSK)” from the “Security Mode” drop-down menu.

2. For “Authentication”, select “WPA-PSK”, “WPA2-PSK”, or “WPA-

PSK + WPA2-PSK”. This setting will have to be identical on the wireless clients that you set up. “WPA-PSK + WPA2-PSK” mode will allow the Router to support clients running either WPA or WPA2 security.

3. “Encryption Technique”, select “TKIP”, “AES”, or “TKIP+AES”.

This setting will have to be identical on the wireless clients that you set up.

4. Enter your pre-shared key (PSK). This can be from eight to 63

characters and can be letters, numbers, or symbols. This same key must be used on all of the wireless clients that you set up. For example, your PSK might be something like: “Smith family network key”. Click “Apply Changes” to finish. You must now set all wireless clients to match these settings.

Page 53

5150

Using the Web-Based Advanced User Interface

section

IMPORTANT: Make sure your wireless computers are updated to work

with WPA2 and have the correct settings to get proper connection to the Router.

Setting WPA Security

Note: To use WPA security, your wireless network cards must be

equipped with software that supports WPA. At the time this User Manual was published, a security patch from Microsoft is available for free download. This patch works only with Windows XP.

Your Router supports WPA-PSK (no server). WPA-PSK uses what is known as a pre-shared key as the security key. A pre-shared key is basically a password that is between eight and 39 characters long. It can be a combination of letters, numbers, or characters. Each client uses the same key to access the network. Typically this is the mode that will be used in a home environment.

5150

Page 54

Using the Web-Based Advanced User Interface

5352

Setting WPA-PSK

1. From the “Security Mode” drop-down menu, select “WPA-PSK (no

server)”.

2. For “Encryption Technique”, select “TKIP” or “AES”. This setting

will have to be identical on the clients that you set up.

3. Enter your pre-shared key. This can be from eight to 39

characters and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up.

4. Click “Apply Changes” to finish. You must now set all clients to

match these settings.

Page 55

5352

Using the Web-Based Advanced User Interface

Setting WEP Encryption

Note to Mac users: The “Passphrase” option will not operate with

Apple® AirPort®. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section.

1. Select “128-bit WEP” or “64-bit WEP” from the drop-down menu.

2. After selecting your WEP encryption mode, you can enter your

WEP key manually by typing in the hex values in the space provided, or you can type a passphrase in the “PassPhrase” field and click “Generate” to create a WEP key from the passphrase. Click “Apply Changes” to finish. You must now set all of your clients to match these settings.

section

3. Encryption in the Router is now set. Each of your computers on

your wireless network will now need to be configured with the same passphrase. Refer to the documentation of your wireless network adapter for information on making this change.

5352

Page 56

Using the Web-Based Advanced User Interface

5554

Using a Hexadecimal Key

A hexadecimal key is a mixture of numbers and letters from A–F and 0–9. 64-bit keys are 10 digits long and can be divided into five twodigit numbers. 128-bit keys are 26 digits long and can be divided into 13 two-digit numbers.

For instance:

AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key

In the boxes below, make up your key by writing in two characters between A–F and 0–9. You will use this key to program the encryption settings on your Router and your wireless computers.

Note to Mac users: Original Apple AirPort products support 64bit encryption only. Apple AirPort 2 products can support 64-bit or 128-bit encryption. Please check your product to see which version you are using. If you cannot configure your network with 128-bit encryption, try 64-bit encryption.

Page 57

5554

Using the Web-Based Advanced User Interface

Using the Access Point Mode

Note: This advanced feature should be employed by advanced users

only. The Router can be configured to work as a wireless network access point. Using this mode will defeat the NAT IP sharing feature and DHCP server. In Access Point (AP) mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to. The default IP address is 192.168.2.254 and subnet mask is 255.255.255.0. These can be customized for your need.

1. Enable the AP mode my selecting “Enable” (1) in the “Use as

Access Point only” page. When you select this option, you will be able to change the IP settings.

2. Set your IP settings to match your network. Click “Apply

Changes” (2).

3. Connect a cable from the “Modem” port on the Router to your

existing network.

The Router is now acting as an access point. To access the Router’s Web-Based Advanced User Interface again, type the IP address you specified into your browser’s navigation bar. You can set the encryption settings, MAC address filtering, SSID, and channel normally.

(1)

section

(2)

5554

Page 58

Using the Web-Based Advanced User Interface

5756

Setting MAC Address Control

The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network.

Note: This list applies only to wireless computers. This list can be

configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client (computer) to which you want to allow network access. The “Block” feature lets you turn on and off access to the network easily for any computer without having to add and remove the computer’s MAC address from the list.

(1)

(2)

(3)

(4)

Setting up an Allow Access List

Select the “Allow” radio button (1) to begin setting up a list of

computers allowed to connect to the wireless network.

2. Next, in the “MAC Address” field that is blank (2), type in the

MAC address of the wireless computer you want to be able to access the wireless network, then click “<<Add” (3).

3. Continue to do this until all of the computers you want to add

have been entered.

4. Click “Apply Changes” (4) to finish.

Page 59

5756

Using the Web-Based Advanced User Interface

(1)

Setting up a Deny Access List

The “Deny Access” list lets you specify computers that you DO NOT want to access the network. Any computer in the list will not be allowed access to the wireless network. All others will.

1. Select the “Deny” radio button (1) to begin setting up a list of

computers to be denied access to the wireless network.

2. Next, in the “MAC Address” field that is blank (2), type in the

MAC address of the wireless computer you want to deny access to the wireless network, then click “<<Add” (3).

3. Continue to do this until all of the computers you want to deny

access to have been entered.

4. Click “Apply Changes” (4) to finish.

(2)

(3)

(4)

section

5756

Page 60

Using the Web-Based Advanced User Interface

5958

Configuring the Firewall

Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including:

• IP Spoofing

• Land Attack Ping of Death (PoD)

• Denial of Service (DoS)

• IP with zero length

• Smurf Attack

• TCP Null Scan

• SYN flood

• UDP flooding

• Tear Drop Attack

• ICMP defect

• RIP defect

• Fragment flooding

The firewall also masks common ports that are frequently used to attack networks. These ports appear to be “stealth” meaning that for all intents and purposes, they do not exist to a would-be hacker. Disabling the firewall protection will not leave your network completely vulnerable to hacker attacks, but it is recommended that you leave the firewall enabled.

Page 61

5958

Using the Web-Based Advanced User Interface

Configuring Internal Forwarding Settings

The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network. Since your internal computers are protected by a firewall, computers outside your network (over the Internet) cannot get to them because they cannot be “seen”. A list of common applications has been provided in case you need to configure the Virtual Server function for a specific application. If your application is not listed, you will need to contact the application vendor to find out which port settings you need.

Choosing an Application

Select your application from the drop-down list. Click “Add”. The settings will be transferred to the next available space in the screen. Click “Apply Changes” to save the setting for that application. To remove an application, select the number of the row that you want to remove then click “Clear”.

section

Manually Entering Settings into the Virtual Server

To manually enter settings, enter the IP address in the space provided for the internal (server) machine, the port(s) required to pass (use a comma between multiple ports), select the port type (TCP or UDP), and click “Apply Changes”. You can only pass one port per internal IP address. Opening ports in your firewall can pose a security risk. You can enable and disable settings very quickly. It is recommended that you disable the settings when you are not using a specific application.

5958

Page 62

Using the Web-Based Advanced User Interface

6160

Setting Client IP Filters

The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers.

To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP

(1). Next, enter “80” in both the port fields (2). Select “Both” (3).

fields Select “Block” (4). You can also select “Always” to block access all of the time. Select the day to start on top (5), the time to start on top

(6), the day to end on the bottom (7), and the time to stop (8) on the

bottom. Select “Enable” (9). Click “Apply Changes”. The computer at the IP address you specified will now be blocked from Internet access at the times you specified. Note: Be sure you have selected the correct time zone under “Utilities> System Settings> Time Zone”.

(1) (2)

(3)

(5)

(4) (7) (8) (9)

(6)

Page 63

6160

Using the Web-Based Advanced User Interface

Enabling the Demilitarized Zone (DMZ)

The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.

To put a computer in the DMZ, enter the last digits of its IP address in the IP field and select “Enable”. Click “Apply Changes” for the change to take effect. If you are using multiple static WAN IP addresses, it is possible to select which WAN IP address the DMZ host will be directed to. Type in the WAN IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, select “Enable” and click “Apply Changes”.

section

6160

Page 64

Using the Web-Based Advanced User Interface

6362

Using Dynamic DNS

The Dynamic DNS service allows you to alias a dynamic IP address to a static host name in any of the many domains DynDNS.org offers, allowing your network computers to be more easily accessed from various locations on the Internet. DynDNS.org provides this service, for up to five host names, free to the Internet community.

The Dynamic DNS to make it easy to access your home PC and stored files while you’re at work. Using the service can ensure that your host name always points to your IP address, no matter how often your ISP changes it. When your IP address changes, your friends and associates can always locate you by visiting yourname.dyndns.org instead!

To register free for your Dynamic DNS host name, please visit

http://www.dyndns.org.

Setting up the Router’s Dynamic DNS Update Client

You must register with DynDNS.org’s free update service before using this feature. Once you have your registration, follow the directions below.

1. Select DynDNS.org from the “DNS Service” drop-down box (1).

2. Enter your DynDNS.org user name in the “User Name” field (2).

3. Enter your DynDNS.org password in the “Password” field (3).

4. Enter the DynDNS.org domain name you set up with DynDNS.org

in the “Domain Name” field (4).

5. Click “Update Dynamic DNS” to update your IP address (5).

Whenever your IP address assigned by your ISP changes, the Router will automatically update DynDNS.org’s servers with your new IP address. You can also do this manually by clicking the “Update Dynamic DNS” button

service is ideal for a home website, file server, or

(5).

(1) (2)

(3)

(4)

(5)

Page 65

6362

Using the Web-Based Advanced User Interface

Blocking an ICMP Ping

Computer hackers use what is known as “pinging” to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens your Router’s security level.

(1)

To turn off the ping response, select “Block ICMP Ping” (1) and click “Apply Changes”. The Router will not respond to an ICMP ping.

Utilities

The “Utilities” screen lets you manage different parameters of the Router and perform certain administrative functions.

section

6362

Page 66

Using the Web-Based Advanced User Interface

6564

Restarting the Router

Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings.

Restarting the Router to Restore Normal Operation

Click the “Restart

Router” button.

2. The following message

will appear. Click “OK”.

3. The following message

will appear. Restarting the Router can take up to 60 seconds. It is important not to turn off the power to the Router during the restart.

4. A 60-second countdown will appear on the screen. When the

countdown reaches zero, the Router will be restarted. The Router home page should appear automatically. If not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser.

Page 67

6564

Using the Web-Based Advanced User Interface

Restoring Factory Default Settings

Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults.

1. Click the “Restore

Defaults” button.

2. The following message

will appear. Click “OK”.

3. The following message

will appear. Restoring the defaults includes restarting the Router. It can take up to 60 seconds. It is important not to turn the power to the Router off during the restart.

section

4. A 60-second countdown will appear on the screen. When the

countdown reaches zero, the Router’s defaults will be restored. The Router home page should appear automatically. If it does not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser.

6564

Page 68

Using the Web-Based Advanced User Interface

6766

Saving a Current Configuration

You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update.

1. Click “Save”. A window

called “File Download” will open. Click “Save”.

2. A window will open that

allows you to select the location where you want to save the configuration file. Select a location. You can name the file anything you want, or use the default name “Config”. Be sure to name the file so you can locate it yourself later. When you have selected the location and name of the file, click “Save”.

Page 69

6766

Using the Web-Based Advanced User Interface

3. When the save is

complete, you will see this window. Click “Close”.

4. The configuration is

now saved.

Restoring a Previous Configuration

This option will allow you to restore a previously saved configuration.

1. Click “Browse”. A

window will open that allows you to select the location of the configuration file. All configuration files end with a “.cfg”. Locate the configuration file you want to restore and double-click on it.

section

6766

Page 70

Using the Web-Based Advanced User Interface

6968

2. You will be asked if you

want to continue. Click “OK”.

3. A reminder window

will appear. It will take up to 60 seconds for the configuration restoration to complete. Click “OK”.

4. A 60-second countdown will appear on the screen. When the

countdown reaches zero, the Router’s configuration will be restored. The Router home page should appear automatically. If not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser.

Page 71

6968

Using the Web-Based Advanced User Interface

Updating the Firmware

From time to time, Belkin may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Router’s firmware to the latest version.

(1)

Checking for a New Version of Firmware

The “Check Firmware” (1) button allows you to instantly check for a new version of firmware. When you click the button, a new browser window will appear informing you that either no new firmware is available or that there is a new version available. If a new version is available, you will have the option to download it.

section

6968

Page 72

Using the Web-Based Advanced User Interface

7170

Downloading a New Version of Firmware

If you click the “Check Firmware” button and a new version of firmware is available, you will see a screen similar to the one below:

1. To download the new

version of firmware, click “Download”.

A window will open that

allows you to select the location where you want to save the firmware file. Select a location. You can name the file anything you want, or use the default name. Be sure to locate the file in a place where you can locate it yourself later. When you have selected the location, click “Save”.

Page 73

7170

Using the Web-Based Advanced User Interface

2. When the save is

complete, you will see the following window. Click “Close”.

3. The download of the

firmware is complete. To update the firmware, follow the next steps in “Updating the Router’s Firmware”.

Updating the Router’s Firmware

1. In the “Firmware

Update” page, click “Browse”. A window will open that allows you to select the location of the firmware update file.

section

2. Browse to the firmware

file you downloaded. Select the file by double-clicking on the file name.

The “Update Firmware”

box will now display the location and name of the firmware file you just selected. Click “Update”.

7170

Page 74

Using the Web-Based Advanced User Interface

7372

3. You will be asked if you

are sure you want to continue. Click “OK”.

4. You will see one more message. This message tells you that

the Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted. Click “OK”.

5. A 60-second countdown will appear on the screen. When the

countdown reaches zero, the Router firmware update will be complete. The Router home page should appear automatically. If not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser.

Page 75

7372

Using the Web-Based Advanced User Interface

Changing System Settings

The “System Settings” page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Router.

Setting or Changing the Administrator Password

The Router ships with NO password entered. If you wish to add a password for greater security, you can set a password here. Write down your password and keep it in a safe place, as you will need it if you need to log into the Router in the future. It is also recommended that you set a password if you plan to use the remote management feature of your Router.

Changing the Login Time-Out Setting

The login time-out option allows you to set the period of time that you can be logged into the Router’s advanced setup interface. The timer starts when there has been no activity. For example, imagine you have made some changes in the advanced setup interface, then left your computer alone without clicking “Logout”. Assuming the time-out is set to 10 minutes, 10 minutes after you leave, the login session will expire. You will have to log into the Router again to make any more changes. The login time-out option is for security purposes and the default is set to 10 minutes.

Note: Only one computer can be logged into the Router’s advanced setup interface at one time.

section

7372

Page 76

Using the Web-Based Advanced User Interface

7574

Setting the Time and Time Zone

The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet. The synchronized clock in the Router is used to record the security log and control client filtering. Select the time zone that you reside in. You have the option to select a primary and a backup NTP server to keep your Router’s clock synchronized. Select your desired NPT server from the drop-down box, or simply keep it as is.

If you reside in an area that observes daylight saving, then place a check mark in the box next to “Enable Daylight Saving”. The system clock may not update immediately. Allow at least 15 minutes for the Router to contact the time servers on the Internet and get a response. You cannot set the clock yourself.

Enabling Remote Management

Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote

management allows you to make changes to your Router’s settings from anywhere on the Internet. There are two methods of remotely managing the Router. The first is to allow access to the Router from anywhere on the Internet by selecting “Any IP address can remotely manage the Router”. By typing in your WAN IP address from any computer on the Internet, you will be presented with a login screen where you need to type in the password of your Router.

The second method is to allow a specific IP address only to remotely manage the Router. This is more secure, but less convenient. To use this method, enter the IP address you know you will be accessing the Router from in the space provided and select “Only this IP address can remotely manage the Router”. Before you enable this function, it is STRONGLY RECOMMENDED that you set your administrator password. Leaving the password empty will potentially open your Router to intrusion.

Page 77

7574

Using the Web-Based Advanced User Interface

Advanced Feature: The “Remote Access Port” option allows you to configure the desired “Remote Access Port for Remote Management” feature. The default access port is set to port 80.

Enabling/Disabling UPnP

UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Some applications require the Router’s firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports. An application that is UPnPcompliant has the ability to communicate with the Router, basically “telling” the Router which way it needs the firewall configured. The Router ships with the UPnP feature disabled. If you are using any applications that are UPnP-compliant, and wish to take advantage of the UPnP features, you can enable the UPnP feature. Simply select “Enable” in the “UPnP Enabling” section of the “Utilities” page. Click “Apply Changes” to save the change.

section

7574

Page 78

Using the Web-Based Advanced User Interface

Enabling/Disabling Auto Firmware Update

This innovation provides the Router with the built-in capability to automatically check for a new version of firmware and alert you that the new firmware is available. When you log into the Router’s advanced interface, the Router will perform a check to see if new firmware is available. If so, you will be notified. You can choose to download the new version or ignore it.

Page 79

Manually Configuring Network Settings

Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet.

Manually Configuring Network Settings in Mac OS up to 9.x

Pull down the Apple menu. Select “Control Panels” and select

“TCP/IP”.

2. You will see the TCP/IP control panel. Select “Ethernet Built-In”

or “Ethernet” in the “Connect via:” drop-down menu (1).

3. Next to “Configure” (2), if “Manually” is

selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router.

4. If not already set, at “Configure:”, choose “Using DHCP Server”.

This will tell the computer to obtain an IP address from the Router.

(1)

(2)

section

5. Close the window.

If you made any changes, the following window will appear. Click “Save”.

Restart the computer. When the computer restarts, your network settings are now configured for use with the Router.

7776

Page 80

Manually Configuring Network Settings

7978

Manually Configuring Network Settings in Mac OS X

Click on the “System Preferences” icon.

2. Select “Network” (1) from the “System Preferences” menu.

(1)

3. Select “Built-in Ethernet” (2) next to “Show” in the Network

menu.

(2)

(3)

(4)

(5)

Page 81

7978

Manually Configuring Network Settings

4. Select the “TCP/IP” tab (3). Next to “Configure” (4), you should

see “Manually” or “Using DHCP”. If you do not, check the PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT selected. If it is, you will need to configure your Router for a PPPoE connection type using your user name and password.

5. If “Manually” is selected, your Router will need to be set up for

a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router.

6. If not already selected, select “Using DHCP” next to “Configure” (4), then click “Apply Now”.

Your network settings are now configured for use with the Router.

section

7978

Page 82

Manually Configuring Network Settings

8180

Manually Configuring Network Settings in Windows 2000, NT, or XP

Click “Start”, “Settings”, then “Control Panel”.

2. Double-click on the “Network and dial-up connections” icon

(Windows 2000) or the “Network” icon (Windows XP).

3. Right-click on the “Local Area Connection” associated with your

network adapter and select “Properties” from the drop-down menu.

4. In the “Local Area Connection Properties” window, click “Internet

Protocol (TCP/IP)” and click the “Properties” button. The following screen will appear:

(1)

(2)

(3)

5. If “Use the following IP address” (2) is selected, your Router

will need to be set up for a static IP connection type. Write the address information the table below. You will need to enter this information into the Router.

6. If not already selected, select “Obtain an IP address

automatically” (1) and “Obtain DNS server address automatically”

(3). Click “OK”.

Your network settings are now configured for use with the Router.

Page 83

8180

Manually Configuring Network Settings

Manually Configuring Network Adapters in Windows 98SE or Me

Right-click on “My Network Neighborhood” and select “Properties”

from the drop-down menu.

2. Select “TCP/IP Settings” for your installed network adapter. You

will see the following window.

(3)

(1)

(2)

3. If “Specify an IP address” is selected, your Router will need to be

set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router.

4. Write the IP address and subnet mask from the “IP Address” tab (3).

5. Click the “Gateway” tab (2). Write the gateway address down in the

chart.

6. Click the “DNS Configuration” tab (1). Write the DNS address(es) in

the chart.

section

7. If not already selected,

select “Obtain IP address automatically” on the IP address tab. Click “OK”.

Restart the computer. When the computer restarts, your network adapter(s) are now configured for use with the Router.

8180

Page 84

Recommended Web Browser Settings

8382

In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the advanced web-based user interface, then change your browser’s settings to the recommended settings in this section.

Microsoft® Internet Explorer 4.0 or Higher

Start your web browser. Select “Tools” then “Internet Options”.

2. In the “Internet Options” screen, there are three selections:

“Never dial a connection”, “Dial whenever a network connection is not present”, and “Always dial my default connection”. If you can make a selection, select “Never dial a connection”. If you cannot make a selection, go to the next step.

3. Under the “Internet Options” screen, click on “Connections” and

select “LAN Settings…”.

Page 85

8382

Recommended Web Browser Settings

4. Make sure there are no check marks next to any of the displayed

options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page.

Netscape® Navigator® 4.0 or Higher

Start Netscape. Click on “Edit” then “Preferences”.

2. In the “Preferences” window, click on “Advanced” then select

“Proxies”. In the “Proxies” window, select “Direct connection to the Internet”.

section

8382

Page 86

Troubleshooting

8584

Setup Assistant CD does not automatically start.

If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive.

1. If the Setup Assistant Welcome screen does not appear within

15-20 seconds, open up your CD-ROM drive by double-clicking on the “My Computer” icon that is located on your desktop.

2. Next, double-click on the CD-ROM drive that the Setup Assistant

CD has been placed in to start the installation.

3. The Setup Assistant should start within a few seconds. If,

instead, a window appears showing the files on the CD, double-click on the icon labeled “SetupAssistant”.

4. If the Setup Assistant still does not start, reference the section

titled “Manually Configuring Network Settings” (page 77 of this User Manual for an alternative setup method).

Setup Assistant cannot find my Router.

If the Setup Assistant is not able to find the Router during the installation process, please check the following items:

1. If the Setup Assistant is not able to find the Router during the

installation process, there may be third-party firewall software installed on the computer attempting to access the Internet. Examples of third-party firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal Firewall, and Norton Personal Firewall. If you do have firewall software installed on your computer, please make sure that you properly configure it. You can determine if the firewall software is preventing Internet access by temporarily turning it off. If, while the firewall is disabled, Internet access works properly, you will need to change the firewall settings to function properly when it is turned on. Please refer to the instructions provided by the publisher of your firewall software for instructions on configuring the firewall to allow Internet access.

Page 87

8584

Troubleshooting

2. Unplug power to the Router for 10 seconds, and then plug the

power back into the Router. Ensure that the Router’s “router” LED is on; it should be solid BLUE. If not, check to make sure that the AC adapter is connected to the Router and plugged into a wall outlet.

3. Ensure that you have a cable connected between (1) the network

(Ethernet) port on the back of the computer and (2) one of the “to Wired Computers” ports on the back of the Router.

Note: The computer should NOT be connected to the port labeled

“to Modem” on the back of the Router.

4. Try shutting down and restarting your computer, then rerunning

the Setup Assistant.

If the Setup Assistant is still unable to find the Router, reference the section titled “Manually Configuring Network Settings” for installation steps.

Setup Assistant cannot connect my Router to the Internet

If the Setup Assistant is not able to connect the Router to the Internet, please check the following items:

1. Use the troubleshooting suggestions within the Setup Assistant.

2. If your ISP requires a user name and password, make sure that

you have typed in your user name and password correctly. Some user names require that the ISP’s domain may be at the end of the name. Example: “myname@myisp.com”. The “@myisp.com” part of the user name may need to be typed as well as your user name.

If you continue to have no Internet connection, reference the section titled “Manually Configuring Network Settings” (page 77 of this User Manual for an alternative setup method).

section

8584

Page 88

Troubleshooting

8786

I can’t connect to the Internet wirelessly.

If you are unable to connect to the Internet from a wireless computer, please check the following items:

1. Look at the lights on your Router. They should be as follows:

• The “router” LED should be on.

• The “ADSL” light should be on, and not blinking.

• The “internet” LED should be on, and not blinking.

• The “Wireless” light should be on, not blinking.

2. Open your wireless utility software by clicking on the icon in the

system tray at the bottom, right-hand corner of the screen.

3. The exact window that opens will vary depending on the model of

wireless card you have; however, any of the utilities should have a list of “Available Networks”—those wireless networks it can connect to.

Does the name of your wireless network appear in the results? Yes, my network name is listed—go to the troubleshooting solution

titled “I can’t connect to the Internet wirelessly, but my network name is listed”.

No, my network name is not listed—go to the troubleshooting solution titled “I can’t connect to the Internet wirelessly, and my network name is not listed”.

Page 89

8786

Troubleshooting

I can’t connect to the Internet wirelessly, but my network name is listed.

If the name of your network is listed in the “Available Networks” list, please follow the steps below to connect wirelessly:

1. Click on the correct network name in the “Available Networks”

list.

2. If the network has security (encryption) enabled, you will need

to enter the network key. For more information regarding security, see the section entitled “Changing the Wireless Security Settings”.

3. Within a few seconds, the tray icon in the lower, left-hand corner

of your screen should turn green, indication of a successful connection to the network.

I can’t connect to the Internet wirelessly, and my network name is not listed.

If the correct network name is not listed under “Available Networks” in the wireless utility, please attempt the following troubleshooting steps:

1. Temporarily move computer, if possible, five to 10 feet from the

Router. Close the wireless utility, and reopen it. If the correct network name now appears under “Available Networks”, you may have a range or interference problem. Please see the suggestions discussed in the section titled “Placement of your N Wireless Modem Router” of this User Manual.

2. Using a computer that is connected to the Router via a network

cable (as opposed to wirelessly), ensure that “Broadcast SSID” is enabled. This setting is found on the Router’s wireless “Channel and SSID” configuration page.

If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support.

section

8786

Page 90

Troubleshooting

8988

• My wireless network performance is inconsistent.

• Data transfer is sometimes slow.

• Signal strength is poor.

• Difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection.

Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases. Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances. Note also that connection speed may decrease as you move farther away from the Router.

In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, five to 10 feet from the Router.

Changing the wireless channel—Depending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability. The default channel the Router is shipped with is channel 11; you may choose from several other channels depending on your region. See the section on page 47 entitled “Changing the Wireless Channel” for instructions on how to choose other channels.

Limiting the wireless transmit rate—Limiting the wireless transmit rate can help improve the maximum wireless range and connection stability. Most wireless cards have the ability to limit the transmission rate. To change this property, go to the Windows Control Panel, open “Network Connections” and double-click on your wireless card’s connection. In the properties dialog, select the “Configure” button on the “General” tab (Windows 98 users will have to select the wireless card in the list box and then click “Properties”), then choose the “Advanced” tab and select the rate property.

Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable. Experiment with different connection rates until you find the best one for your environment. Note that all available transmission rates should be acceptable for browsing the Internet. For more assistance, see your wireless card’s user manual.

Page 91

8988

Troubleshooting

I am having difficulty setting up Wired Equivalent Privacy (WEP) security on my Belkin Router.

Log into your Router.

Open your web browser and type in the IP address of the Router.

(The Router’s default is 192.168.2.1.) Log into your Router by clicking on the “Login” button in the top right-hand corner of the screen. You will be asked to enter your password. If you never set a password, leave the “Password” field blank and click “Submit”.

Click the “Wireless” tab on the left of your screen. Select the

“Encryption” or “Security” tab to get to the security settings page.

2. Select “128-bit WEP” from the drop-down menu.

3. After selecting your WEP encryption mode, you can type in

your hex WEP key manually, or you can type in a passphrase in the “Passphrase” field and click “Generate” to create a WEP key from the passphrase. Click “Apply Changes” to finish. You must now set all of your clients to match these settings. A hex (hexadecimal) key is a mixture of numbers and letters from A-F and 0-9. For 128-bit WEP, you need to enter 26 hex keys.

For example: C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key

4. Click “Apply Changes” to finish. Encryption in the Wireless Router

is now set. Each of your computers on your wireless network will now need to be configured with the same security settings.

WARNING: If you are configuring the Router from a computer with

a wireless client, you will need to ensure that security is turned on for this wireless client. If this is not done, you will lose your wireless connection.

Note to Mac users: Original Apple AirPort products support 64-bit

encryption only. Apple AirPort 2 products can support 64-bit or 128bit encryption. Please check your Apple AirPort product to see which version you are using. If you cannot configure your network with 128bit encryption, try 64-bit encryption.

section

8988

Page 92

Troubleshooting

9190

I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card.

The client card must use the same key as the Router. For instance, if your Router uses the key 00112233445566778899AABBCC, then the client card must be set to the exact same key.

1. Double-click the Signal Indicator icon to bring up the “Wireless

Network” screen.

2. The “Advanced” button will allow you to view and configure more

options of the card.

3. Once the “Advanced” button is clicked, the Belkin Wireless LAN

Utility will appear. This Utility will allow you to manage all the advanced features of the Belkin Wireless Card.

4. Under the “Wireless Network Properties” tab, select a network

name from the “Available Networks” list and click the “Properties” button.

5. Under “Data Encryption”, select “WEP”.

6. Ensure the check box “The key is provided for me automatically”

at the bottom is unchecked. If you are using this computer to connect to a corporate network, please consult your network administrator if this box needs to be checked.

7. Type your WEP key in the “Network key” box.

Important: A WEP key is a mixture of numbers and letters from

A-F and 0-9. For 128-bit WEP, you need to enter 26 keys. This network key needs to match the key you assign to your Router.

For example:

C3030FAF4BB2C3D44BC3D4E7E4 = 128-bit key

8. Click “OK”, and then “Apply” to save the settings.

If you are NOT using a Belkin wireless client card, please consult the manufacturer’s user manual for that wireless client card.

Page 93

9190

Troubleshooting

Do Belkin products support WPA? Note:

To use WPA security, all your clients must be upgraded to drivers and software that support it. At the time of this FAQ publication, a security patch download is available, for free, from Microsoft. This patch works only with the Windows XP operating system.

Download the patch here: http://www.microsoft.com/downloads You also need to download the latest driver for your Belkin Wireless

802.11g Desktop or Notebook Network Card from the Belkin support site. Other operating systems are not supported at this time. Microsoft’s patch only supports devices with WPA-enabled drivers such as Belkin 802.11g products

Download the latest driver at http://web.belkin.com/support.

I am having difficulty setting up Wireless Protected Access (WPA) security on my Belkin Router for a home network.

From the “Security Mode” drop-down menu, select “WPA-PSK

(no server)”.

2. For “Encryption Technique”, select “TKIP” or “AES”. This setting

will have to be identical on the clients that you set up.

3. Enter your pre-shared key. This can be from eight to 63

characters and can be letters, numbers, symbols, or spaces. This same key must be used on all of the clients that you set up. For example, your PSK might be something like: “Smith family network key”.

4. Click “Apply Changes” to finish. You must now set all clients to

match these settings.

section

9190

Page 94

Troubleshooting

9392

I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin wireless client card for a home network.

Clients must use the same key that the Router uses. For instance, if the key is “Smith Family Network Key” in the Router, the clients must also use that same key.

1. Double-click the Signal Indicator icon to bring up the “Wireless

Network” screen. The “Advanced” button will allow you to view and configure more options of your card.

2. Once the “Advanced” button is clicked, the Belkin Wireless Utility

will appear. This Utility will allow you to manage all the advanced features of the Belkin Wireless Card.

3. Under the “Wireless Network Properties” tab, select a

network name from the “Available Networks” list and click the “Properties” button.

4. Under “Network Authentication”, select “WPA-PSK (no server).

5. Type your WPA key in the “Network key” box. Important: WPA-PSK is a mixture of numbers and letters from

A-Z and 0-9. For WPA-PSK you can enter eight to 63 characters. This network key needs to match the key you assign to your Router.

6. Click “OK, then “Apply” to save the settings.

Page 95

9392

Troubleshooting

I am NOT using a Belkin client card for a home network and I am having difficulty setting up Wireless Protected Access (WPA) security.

If you are not using a Belkin Wireless Desktop or Wireless Notebook Network Card that is not equipped with WPA-enabled software, a file from Microsoft called “Windows XP Support Patch for Wireless Protected Access” is available for free download. Download the patch from Microsoft by searching the knowledge base for Windows XP WPA.

Note: The file that Microsoft has made available works only with

Windows XP. Other operating systems are not supported at this time. You also need to ensure that the wireless card’s manufacturer supports WPA and that you have downloaded and installed the latest driver from their support site.

Supported Operating Systems:

• Windows XP Professional

• Windows XP Home Edition

1. Under Windows XP, click “Start > Control Panel >

Network Connections”.

2. Right-click on the “Wireless Networks” tab. Ensure the “Use

Windows to configure my wireless network settings” check box is checked.

3. Under the “Wireless Networks” tab, click the “Configure”.

4. For a home or small business user, select “WPA-PSK” under

“Network Administration”.

Note: Select WPA (with radius server) if you are using this computer

to connect to a corporate network that supports an authentication server such as a radius server. Please consult your network administrator for further information.

5. Select “TKIP” or “AES” under “Date Encryption”. This setting will

have to be identical to the Router that you set up.

6. Type in your encryption key in the “Network key” box. Important: Enter your pre-shared key. This can be from eight to 63

characters and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up.

7. Click “OK” to apply settings.

section

9392

Page 96

Troubleshooting

9594

What’s the difference between 802.11b, 802.11g, 802.11a, and draft 802.11n?

Currently there are four levels of wireless networking standards, which transmit data at very different maximum speeds. Each is based on the designation for certifying network standards. The most common wireless networking standard, 802.11b, transmits information at 11Mbps; 802.11a and 802.11g work at 54Mbps; and draft 802.11n works at 108Mbps. See the chart on the next page for more detailed information.

Page 97

9594

Troubleshooting

Wireless Comparison Chart

G (802.11g)

Wireless

Technology

Up to 54Mbps* Up to 54Mbps* Up to 300Mbps* Up to 300Mbps*

Speed*

Common household devices such as cordless phones and microwave ovens may interfere with

Frequency

the unlicensed band 2.4GHz

Compatible with

802.11b/g

Compatibility

Up to 400 ft.* Up to 1,000 ft.* Up to 1,200 ft.* Up to 1,400 ft.*

Coverage*

G Plus MIMO (802.11g with MIMO MRC)

Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz

Compatible with

802.11b/g

N MIMO (draft 802.11n with MIMO)

Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz

Compatible with draft 802.11n** and 802.11b/g

N1 MIMO (draft 802.11n with MIMO)

Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz

Compatible with draft 802.11n** and 802.11b/g

section

Common— widespread use for Internet sharing

Advantage

*Distance and connection speeds will vary depending on your networking environment.

**This Router is compatible with products based on the same version of the draft

802.11n specifications, and may require a software upgrade for best results.

Better coverage and consistent speed at range

Enhanced speed and coverage

9594

Leading edge— best coverage and throughput

Page 98

Troubleshooting

Technical Support

You can find technical-support information on our website, www.belkin.com, by navigating to the tech-support section.

If you want to contact technical support by phone, please call the number you need from the list below*.

*Local rates apply.

NETHERLANDS

0900 - 040 07 90

€0.10 per minute NORWAY 81 50 0287 POLAND 00800 - 441 17 37 PORTUGAL 707 200 676 RUSSIA 495 580 9541 SOUTH AFRICA 0800 - 99 15 21 SPAIN 902 - 02 43 66 SWEDEN 07 - 71 40 04 53 SWITZERLAND 08 - 48 00 02 19 UNITED KINGDOM 0845 - 607 77 87

OTHER COUNTRIES +44 - 1933 35 20 00

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/nl/ networ king /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/fr/netw orki ng/

http://www.b elkin.com/de/ networ king /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/it /sup port/ tech/i ssues _more. asp

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/nl/ networ king /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/net working /

http://www.b elkin.com/uk/ networ king/

http://www.b elkin.com/es/ suppor t/tec h/netw orking supp ort.asp

http://www.b elkin.com/se/ suppor t/tec h/netw orki ngsupp ort.as p

http://www.b elkin.com/uk/ networ king/

Page 99

Information

Belkin International, Inc., Limited Lifetime Product Warranty

What this warranty covers.

Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship.

What the period of coverage is. Belkin warrants the Belkin product for the lifetime of the product.

What will we do to correct problems?

Product Warranty.

Belkin will repair or replace, at its option, any defective product free of charge (except for shipping charges for the product).

What is not covered by this warranty?

All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God such as flood, lightning, earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e. brownouts or sags), non-authorized program, or system equipment modification or alteration.

How to get service.

To get service for your Belkin product you must take the following steps:

1. Contact Belkin Tech Support at the number listed on page 99 within 15 days of the Occurrence. Be prepared to provide the following information: a. The part number of the Belkin product. b. Where you purchased the product. c. When you purchased the product. d. Copy of original receipt.

2. Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim.

section

9796

Page 100

Information

9998

Belkin reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser. Damaged equipment must remain available for inspection until the claim is finalized. Whenever claims are settled, Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have.

How state law relates to the warranty.

THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you

FOR USE IN

AT BE CY CZ DK

FI FR DE GR

You can find the declaration of conformity for this product at the following URL,

http://www.belkin.com/doc/

For information on product disposal please refer to http://environmental.belkin.com

EE HU IE IT LV LT LU MT NL PL PT

SI ES SE GB

SK IS LI NO CH BG RO TR

OPERATES ON

CHANNELS 1-13

Belkin F5D8633-4 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual