Belkin F5D7234V4 User Manual

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 1 of 61

B E L K I N Wireless G Router

User Manual
8820-00118 Rev.A01 F5D7234-4

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 2 of 61

Table of Contents

1. Introduction

Benefits of a Home Network
Advantages of a Wireless Network
Placement of your Router for Optimal Performance

2. Product Overview

Product Features

3. Knowing your Router

Package Contents
System Requirements
Setup Assistant Software System Requirements

4. Connecting and Configuring your Router

5. Alternate Setup Method

6. Using the Web-Based Advanced User Interface

Changing LAN Settings
Viewing the DHCP Client List Page
Configuring the Wireless Network Settings
Securing your Wi-Fi Network

WEP Setup
Using Wi-Fi Protected Setup
WPA Setup
Setting WPA/WPA2

Guest Access (Optional)

Using the Access Point Mode
Configuring the Firewall

Setting MAC Address Filtering

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 3 of 61

Enabling the DMZ
Utilities Tab

Restarting the Router
Updating the Firmware

7. Manually Configuring Network Settings

8. Recommended Web Browser Settings

9. Troubleshooting

10. Information

Introduction

Thank you for purchasing the Belkin Wireless G Router (the Router). The
following two short sections discuss the benefits of home networking and outline
best practices for maximizing your wireless home network range and
performance. Please be sure to read through this User Manual completely, and
pay special attention to the section entitled “Placement of your Router for Optimal
Performance” on page 2.

Benefits of a Home Network

• Share one high-speed Internet connection with all the computers in your
home

• Share resources, such as files and hard drives among all the connected
computers in your home

• Share a single printer with the entire family

• Share documents, music, video, and digital pictures

• Store, retrieve, and copy files from one computer to another

• Simultaneously play games online, check Internet email, and chat

Advantages of a Wireless Network

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 4 of 61

• Mobility – you no longer need a dedicated “computer room”—now you can
work on a networked laptop or desktop computer anywhere within your
wireless range

• Easy installation – the Belkin Setup Assistant Software makes setup
simple

• Flexibility – set up and access printers, computers, and other networking
devices from anywhere in your home

• Easy expansion – the wide range of Belkin networking products lets you
expand your network to include devices such as printers and gaming
consoles

• No cabling required – you can spare the expense and hassle of retrofitting
Ethernet cabling throughout the home or office

• Widespread industry acceptance – choose from a wide range of
interoperable networking products

Placement of your Router for Optimal Performance
Important Factors for Placement and Setup

Your wireless connection will be stronger the closer your computer is to your
Router. Typical indoor operating range for wireless devices is between 100 and
200 feet.

In the same way, your wireless connection and performance will degrade
somewhat as the distance between your Router and connected devices
increases. This may or may not be noticeable to you. As you move farther from
your Router, connection speed may decrease. Factors that can weaken signals
simply by getting in the way of your network’s radio waves are metal appliances
or obstructions, and walls.

If you have concerns about your network’s performance that might be related
to range or obstruction factors, try moving the computer to a position
between five and 10 feet away from the Router in order to see if distance is the
problem. If difficulties persist even at close range, please contact Belkin
Technical Support.

Note: While some of the items listed below can affect network performance,
they will not prohibit your wireless network from functioning; if you are
concerned that your network is not operating at its maximum effectiveness,
this checklist may help.

1. Wireless Router Placement

Place your Router, the central connection point of your network, as close as
possible to the center of your wireless network devices.

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 5 of 61

To achieve the best wireless network coverage for your “wireless clients” (i.e.,
computers enabled by Belkin Wireless Notebook Network Cards, Wireless
Desktop Network Cards, and Wireless USB Adapters):

• Ensure that your Router’s networking antennas are parallel to each other,
and are positioned vertically (toward the ceiling). If your Router itself is
positioned vertically, point the antennas as much as possible in an upward
direction.

• In multistory homes, place the Router on a floor that is as close to the
center of the home as possible. This may mean placing the Router on an
upper floor.

• Try not to place the Router near a cordless phone.

2. Avoid Obstacles and Interference

Avoid placing your Router near devices that may emit radio “noise,” such as
microwave ovens. Dense objects that can inhibit wireless communication include:

• Refrigerators

• Washers and/or dryers

• Metal cabinets

• Large aquariums

• Metallic-based, UV-tinted windows

If your wireless signal seems weak in some spots, make sure that objects such
as these are not blocking the signal’s path (between your computers and Router).

3. Cordless Phones

If the performance of your wireless network is impaired after attending to the
above issues, and you have a cordless phone:

• Try moving cordless phones away from the Router and your wireless­enabled computers.

• Unplug and remove the battery from any cordless phone that operates on
the 2.4GHz band (check the manufacturer’s information). If this fixes the
problem, your phone may be interfering.

• If your phone supports channel selection, change the channel on the
phone to the farthest channel from your wireless network. For example,
change the phone to channel 1 and move your Router to channel 11. See
your phone’s user manual for detailed instructions.

• If necessary, consider switching to a 900MHz cordless phone.

4. Choose the “Quietest” Channel for your Wireless Network

In locations where homes or offices are close together, such as apartment
buildings or office complexes, there may be wireless networks nearby that can
conflict with yours.
Use the Site Survey capabilities found in the wireless utility of your wireless
adapter or card to locate any other wireless networks that are available (see your

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 6 of 61

wireless adapter’s or card’s user manual), and move your Router and computers
to a channel as far away from other networks as possible.

• Experiment with more than one of the available channels in order to find
the clearest connection and avoid interference from neighboring cordless
phones or other wireless devices.

• For Belkin wireless networking products, use the detailed Site Survey and
wireless channel information included with your Wireless Network Card or
Adapter. See your Network Card’s user guide for more information.

These guidelines should allow you to cover the maximum possible area with your
Router. Should you need to cover an even wider area, we suggest the Belkin
Wireless G Range Extender/Access Point.

5. Secure Connections, VPNs, and AOL
Secure connections typically require a user name and password, and are used
where security is important. Secure connections include:

• Virtual Private Network (VPN) connections, often used to connect
remotely to an office network

• The “Bring Your Own Access” program from America Online (AOL), which
lets you use AOL through broadband provided by another cable or DSL
service

• Most online banking websites

• Many commercial websites that require a user name and password to

access your account

Secure connections can be interrupted by a computer’s power management
setting, which causes it to “go to sleep.” The easiest solution to avoid this is to
simply reconnect by rerunning the VPN or AOL software, or by re-logging into the
secure website.
A second alternative is to change your computer’s power management settings
so it does not go to sleep; however, this may not be appropriate for portable
computers. To change your power management setting under Windows, see the
“Power Options” item in the Control Panel.
If you continue to have difficulty with secure connections, VPNs, and AOL,
please review the steps above to be sure you have addressed these issues.

For more information regarding our networking products, visit our website at

www.belkin.com/networking.

Product Overview
Product Features

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 7 of 61

In minutes you will be able to share your Internet connection and network your
computers. The following is a list of features that make your new Belkin Wireless
G Router an ideal solution for your home or small office network.

Works with Both PCs and Mac® Computers

The Router supports a variety of networking environments including Mac OS® X,
Linux®, Windows® 2000, XP, Vista®, and others. All that is needed is an Internet
browser and a network adapter that supports TCP/IP (the standard language of
the Internet).

Patent-Pending Network Status Display

Lighted LEDs on the front of the Router indicate which functions are in
operation. You’ll know at-a-glance whether your Router is connected to
the Internet. This feature eliminates the need for advanced software and
status-monitoring procedures.

Web-Based Advanced User Interface

You can set up the Router’s advanced functions easily through your web browser,
without having to install additional software onto the computer. There are no
disks to install or keep track of and, best of all, you can make changes and
perform setup functions from any computer on the network quickly and easily.

NAT IP Address Sharing

Your Router employs Network Address Translation (NAT) to share the single IP
address assigned to you by your Internet Service Provider while saving the cost
of adding IP addresses to your Internet service account.

SPI Firewall

Your Router is equipped with a firewall that will protect your network from a wide
array of common hacker attacks including IP Spoofing, Land Attack, Ping of
Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP
Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect,
and fragment flooding.

Integrated 10/100 4-Port Switch

The Router has a built-in, 4-port network switch to allow your wired computers to
share printers, data and MP3 files, digital photos, and much more. The switch
features automatic detection so it will adjust to the speed of connected devices.
The switch will transfer data between computers and the Internet simultaneously
without interrupting or consuming resources.

Universal Plug-and-Play (UPnP) Compatibility

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 8 of 61

UPnP (Universal Plug-and-Play) is a technology that offers seamless operation
of voice messaging, video messaging, games, and other applications that are
UPnP-compliant.

Support for VPN Pass-Through

If you connect to your office network from home using a VPN connection, your
Router will allow your VPN-equipped computer to pass through the Router and to
your office network.

Built-In Dynamic Host Configuration Protocol (DHCP)

Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the
easiest possible connection of a network. The DHCP server will assign IP
addresses to each computer automatically so there is no need for a complicated
networking setup.

Setup Assistant Software

The Setup Assistant Software takes the guesswork out of setting up your Router.
This automatic software determines your network settings for you and sets up the
Router for connection to your Internet Service Provider (ISP). In a matter of
minutes, your Wireless Router will be up and running on the Internet.

NOTE: Setup Assistant Software is compatible with Windows 2000, XP, Vista,
and Mac OS X. If you are using another operating system, the Wireless Router
can be set up using the Alternate Setup Method described in this User Manual
(see page 24).

Integrated 802.11g Wireless Access Point

802.11g is an exciting new wireless technology that achieves data rates up to
54Mbps, nearly five times faster than 802.11b.

MAC Address Filtering

For added security, you can set up a list of MAC addresses (unique client
identifiers) that are allowed access to your network. Every computer has its own
MAC address. Simply enter these MAC addresses into a list using the Web­Based Advanced User Interface and you can control access to your network.

Knowing your Router
Package Contents

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 9 of 61

• Belkin G Wireless Router

• Quick Installation Guide

• Belkin Setup Assistant Software CD with User Manual

• Belkin RJ45 Ethernet Networking Cable

• Power Supply

System Requirements

• Broadband Internet connection such as a cable or DSL modem with RJ45
(Ethernet) connection

• At least one computer with an installed network interface adapter

• TCP/IP networking protocol installed on each computer

• RJ45 Ethernet networking cable

• Internet browser

Setup Assistant Software System Requirements

• A computer running Windows 2000, XP, or Vista, or Mac OS X v10.x

• Minimum 1GHz processor and 128MB RAM

• Internet browser

The Router has been designed to be placed on a desktop. All of the cables exit
from the rear of the Router for better organization and utility. The Network Status
Display is easily visible on the FRONT of the Router to provide you with
information about network activity and status.

A. Internet Status

This unique icon shows you when the Router is connected to the Internet. When the
light is off, the Router is NOT connected to the Internet. When the light is blinking
amber, the Router is attempting to connect to the Internet. When the light is solid blue,
the Router is connected to the Internet. When using the “Disconnect after x minutes”
feature, this icon becomes extremely useful in monitoring the status of your Router’s
connection.

Off Router is NOT connected to the Internet
Blinking Green Router is attempting to connect to the Internet
Solid Green Router is connected to the Internet

B. Modem Status

This icon lights in blue to indicate that your modem is connected properly to the Router.
It turns amber when problem is detected.

Off Router is NOT connected to modem
Blinking Router is connecting to the ISP

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 10 of 61

Green
Solid Green Router is connected to modem and functioning properly

C. Router/Power Status

When you apply power to the Router or restart it, a short period of time elapses while the

Router boots up. During this time, the “router” icon blinks. When the Router has completely
booted up, the “router” icon becomes a solid light, indicating the Router is ready for use.

Off Router is off
Blinking Green Router is booting up
Solid Green Router is on and ready

D. Wired-Computer Status

Off Wired computer is not present
Solid Green Wired computer is connected to the Router
Blinking Green Data Transmission between the Router and wi red computer(s)

E. Wireless-Computer Status
Off Wireless computer is not present

Solid Green Wireless computer is connected to the Router
Blinking Green Data Transmission between the Router and wireless computer(s)

F. Wireless Security

Off Wireless security is off
Solid Green Wireless security is on

Blinking
Green

G. Wi-Fi Protected Setup (WPS) button

WPS sync in progress

This button is used for the Wi-Fi Protected Setup feature. Please refer to the
“Changing the Wireless Security Settings” section.

H. Connection to Modem – Yellow

This port is for connection to your cable or DSL modem. Use the cable that was

provided with the Router to connect the modem to this port. Use of a cable
other than the cable supplied with the Router may not work properly.

I. Connections to Computers (Wired Computer Ports) – Gray

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 11 of 61

Connect your wired (non-wireless) computers to these ports. These ports are

RJ45, 10/100 auto-negotiation, auto-uplinking ports for standard UTP
category 5 or 6 Ethernet cable. The ports are labeled 1 through 4.

J.. Power Jack

Connect the included 9V/1A DC power supply to this jack.

K. Reset Button

The “Reset” button is used in rare cases when the Router may function

improperly. Resetting the Router will restore the Router’s normal operation
while maintaining the programmed settings. You can also restore the factory
default settings by using the “Reset” button. Use the restore option in
instances where you may have forgotten your login password.

a. Resetting the Router

Push and release the “Reset” button. The lights on the Router will momentarily
flash. The “router” light will begin to blink. When the “router” light becomes solid
again, the reset is complete.

b. Restoring the Factory Defaults

Press and hold the “Reset” button for at least 10 seconds, then release it. The
lights on the Router will momentarily flash. The “router” light will begin to blink.
When the “router” light becomes solid again, the reset is complete.

Connecting and Configuring your Router

Verify the contents of your box. You should have the following:

• Belkin G Wireless Router

• Quick Installation Guide

• Belkin Setup Assistant Software CD with User Manual

• RJ45 Ethernet Networking Cable (for connection of the Router to the modem)

• Power Supply

Modem Requirements

Your cable or DSL modem must be equipped with an RJ45 Ethernet port. Many
modems have both an RJ45 Ethernet port and a USB connection. If you have a
modem with both Ethernet and USB, and are using the USB connection at this
time, you will be instructed to use the RJ45 Ethernet port during the installation
procedure. If your modem has only a USB port, you can request a different type

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 12 of 61

of modem from your ISP, or you can, in some cases, purchase a modem that has
an RJ45 Ethernet port on it.

ALWAYS INSTALL YOUR ROUTER FIRST! IF YOU ARE INSTALLING
NUMEROUS NETWORK DEVICES FOR THE FIRST TIME, IT IS IMPORTANT
THAT YOUR ROUTER IS CONNECTED AND RUNNING BEFORE
ATTEMPTING TO INSTALL OTHER NETWORK COMPONENTS SUCH AS
NOTEBOOK CARDS AND DESKTOP CARDS.

Setup Assistant

Belkin has provided our Setup Assistant software to make installing your Router
a simple and easy task. You can use it to get your Router up and running in
minutes. The Setup Assistant requires that your Windows 2000/XP, Vista, or Mac
OS X v10.4 or v10.5 computer be connected directly to your cable or DSL
modem and that the Internet connection is active and working at the time of
installation. If it is not, you must use the “Alternate Setup Method” section of this
User Manual to configure your Router. Additionally, if you are using an operating
system other than Windows 2000/XP, Vista, or Mac OS X v10.4 or v10.5, you
must set up the Router using the “Alternate Setup Method” section of this User
Manual.

[1]

Put the router next to your DSL or cable modem.

Turn the antenna straight up.

[2]

Make sure your cable or DSL line is plugged into your modem.

Connect the modem to the router's "modem" port with an Ethernet cable. (Your computer
might be plugged in here already.)

Connect your computer to the router with another Ethernet cable (temporarily if need be).

[3]

Plug the router's power supply into the router and a power outlet.

Plug in your modem and make sure it turns on. If your modem is already on, unplug it,
wait a few seconds, and plug it back in.

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 13 of 61

Put the CD into your computer. If the Setup Assistant doesn't run automatically, browse
the CD, find the Setup Assistant icon, and run it.

IMPORTANT: Run the Setup Assistant from the computer that is directly connected to the Router from

Step 1.B.

Note for Windows Users: If the Setup Assistant does not start up automatically,
select your CD-ROM drive from “My Computer” and double-click on the file
named “SetupAssistant” to start the Setup Assistant.

Select Country

Select your country from the drop-down box. Click “Begin” to continue.

Confirmation Screen
Verify that you have completed all QIG steps by checking the box to the right of
the arrow. Click “Next” to continue.

Progress Screen
Setup Assistant will show you a progress screen each time a step in the setup
has been completed.

2.1 Checking Settings

The Setup Assistant will now examine your computer’s network settings and
gather information needed to complete the Router’s connection to the Internet.

2.2 Verifying Hardware Connections

The Setup Assistant will now verify your hardware connection.

2.3 Naming your Wireless Network

The Setup Assistant will display the default wireless network name or Service Set
Identifier (SSID). This is the name of your wireless network to which your
computers or devices with wireless network adapters will connect. You can either
use the default or change it to something unique. Write down this name for future
reference.

2.4 Requesting Internet Account Info (if needed)

Select your ISP from the drop-down boxes.
If your Internet account requires a login and password, you will be prompted with

a screen similar to the illustration below. Click “Next” to continue.

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 14 of 61

2.5 Configuring the Router

The Setup Assistant will now configure your Router by sending data to the
Router and restarting it. Wait for the on-screen instructions.

Note: Do not disconnect any cable or power off the Router while the Router is
rebooting. Doing so will render your Router inoperable.

2.6 Checking Internet Connection

We are almost done. The Setup Assistant will now check your connection to the
Internet.

Congratulations

You have finished installing your new Belkin Router. You will see the
Congratulations screen when your Router can connect to the Internet. You can
begin surfing by opening your browser and going to any website.

You can use the Setup Assistant to set up your other wired and wireless
computers to connect to the Internet by clicking “Next”. If you decide to add
computers to your Router later, select “Finish—return to Main Menu” and then
click “Next”.

Troubleshooting

If the Setup Assistant is not able to connect to the Internet, you will see the
following screen. Follow the on-screen instructions to go through the
troubleshooting steps.

2.7 Optional: Assistance Connecting Other Computers

This optional step will help you to connect additional wired and wireless
computers to your network. Follow the on-screen instructions.

Once you have verified that your other wired and wireless computers are
properly connected, your network is set up and working. You can now surf the
Internet. Click “Next” to return to the main menu.

Step 3: Set Up Wireless Security – Run the Security Assistant Software
Now that your network is set up and working, it is recommended that you turn on

wireless security to prevent unauthorized access to your network from
neighboring wireless-enabled computers. The Security Assistant will guide you
through the process. Click “Security Assistant” and follow the on-screen
instructions.

F5D7234-4 v4 Wireless G Router User Manual Rev1

p

Page 15 of 61

IMPORTANT: Run the Setup Assistant from the computer that is directly connected to the Router

from Ste

1.B.

Progress Screen

The Security Assistant will show you a progress screen each time a step has
been completed.

3.1 Picking the Security Type

Select the security type for your wireless network and click “Next” to continue.

3.2 Creating a Network Key

Enter a network key (PSK) for your wireless network and click “Next” to continue.

3.3 Transferring the Key

After setting up your wireless security, you will have to transfer the network key
to each of your wireless computers. Click on “Transfer Key” if you have a USB
flash drive. Follow the on-screen instructions, or click on “Print” to print the
information. Manually enter it to each wireless computer. Then, click “Next” to
continue.

3.4 Verifying the Connection

If all your wireless computers are able to connect to the Router, click “Next”. If
you are having trouble, select “I had problems with at least one computer” and
click “Next”. Then, follow the on-screen instructions.

Congratulations

Once you have verified that your wireless computers are properly connected,
your wireless network is set up and secured. You now can run your network
wirelessly and securely. Click “Finish” to take you back to the main menu.

Alternate Setup Method

The Web-Based Advanced User Interface is a web-based tool that you can use
to set up the Router if you don’t want to use the Setup Assistant Software. You
can also use it to manage advanced functions of the Router. From the Web­Based Advanced User Interface, you can perform the following tasks:

• View the Router’s current settings and status

• Configure the Router to connect to your ISP with the settings that they provided
you

• Change the current network settings such as the Internal IP address, the IP
address pool, DHCP settings, and more

• Set the Router’s firewall to work with specific applications (port forwarding)

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 16 of 61

• Set up security features such as client restrictions, MAC address filtering, WEP,
and WPA

• Enable the DMZ feature for a single computer on your network

• Change the Router’s internal password

• Enable/Disable UPnP (Universal Plug-and-Play)

• Reset the Router

• Back up your configuration settings

• Reset the Router’s default settings

• Update the Router’s firmware

Step 1 Set up your Computer’s Network Settings to Work with a DHCP
Server

See the section in this User Manual called “Manually Configuring Network
Settings” for directions.

Step 2 Configure the Router Using the Web-Based Advanced User Interface

Using your Internet browser, you can access the Router’s Web-Based Advanced
User Interface. In your browser, type “192.168.2.1” (you do not need to type in
anything else such as “http://” or “www”). Then press the “Enter” key.

(insert screenshot, “192.168.2.1”)
PLEASE NOTE: If you have difficulty accessing the Router’s Web-Based

Advanced User Interface, go to the section entitled “Manually Configuring
Network Settings”.

Logging into the Router

You will see the Router’s home page in your browser window. The home page is
visible to any user who accesses the Router via 192.168.2.1. To make any
changes to the Router’s settings, you have to log in. Clicking the “Login” button
or clicking on any one of the links on the home page will take you to the login
screen. The Router ships with no password entered. In the login screen, leave
the password blank and click the “Submit” button to log in.

Logging out of the Router

Only one computer can log into the Router at any given time for the purposes of
making changes to the settings of the Router. Once a user has logged in to make
changes, there are two ways that the computer can be logged out. Clicking the
“Logout” button will log the computer out. The second method is automatic. The
login will time out after a specified period of time. The default login time-out is 10

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 17 of 61

minutes. This can be changed from 1 to 99 minutes. For more information, see
the section in this manual entitled “Changing the Login Time-Out Setting”.

Using the Web-Based Advanced User Interface

The home page is the first page you will see when you access the Web-Based
Advanced User Interface (UI). The home page shows you a quick view of the
Router’s status and settings. All advanced setup pages can be reached from this
page.

1. Quick-Navigation Links

You can go directly to any of the Router’s UI pages by clicking directly on
these links. The links are divided into logical categories and grouped by tabs
to make finding a particular setting easier. Clicking on the header of each tab
will show you a short description of the tab’s functions.

2. Home Button

The “Home” button is available in every page of the UI. Pressing this button
will take you back to the home status page.

3. Internet Status Indicator

This indicator is visible in all pages of the UI, indicating the connection status
of the Router. When the indicator says “Connected” in blue, the Router is
connected to the Internet. When the Router is not connected to the Internet,
the indicator will read “No Connection” in RED. The indicator is automatically
updated when you make changes to the settings of the Router.

4. Login/Logout Button

This button enables you to log in and out of the Router. When you are logged
into the Router, this button will change to read “Logout”. Logging into the
Router will take you to a separate login page where you will need to enter a
password. When you are logged into the Router, you can make changes to
the settings. When you are finished making changes, you can log out of the
Router by clicking the “Logout” button. For more information about logging
into the Router, see the section called “Logging into the Router”.

5. Help Button

The “Help” button gives you access to the Router’s help pages. Help is also
available on many pages by clicking “more info” next to certain sections of
each page.

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 18 of 61

6. Language

This shows the active language for the User Interface. Select a desirable
language by clicking one of the available languages.

7. LAN Settings

Shows the settings of the Local Area Network (LAN) side of the Router.
Changes can be made to the settings by clicking on any one of the features
listed, or by clicking the “Quick Navigation” links on the left side of the screen.

8. Features

Shows the status of the Router’s NAT, firewall, and wireless features.
Changes can be made to the settings by clicking on any one of the features
listed, or by clicking the “Quick Navigation” links on the left side of the screen.

9. Internet WAN Settings

Shows the settings of the Internet/WAN side of the Router that connects to
the Internet. Changes can be made to the settings by clicking on any one of
the features, or by clicking the “Quick Navigation” links on the left side of the
screen.

10. Version Info

Shows the firmware version, boot-code version, hardware version, and serial
number of the Router.

11. Page Name

The page you are on can be identified by this name. This User Manual will
sometimes refer to pages by name. For instance “LAN > LAN Settings” refers
to the “LAN Settings” page.

Step 3 Configure your Router for Connection to your Internet Service
Provider (ISP)

The “Internet/WAN” tab is where you will set up your Router to connect to your
Internet Service Provider (ISP). The Router is capable of connecting to virtually
any ISP’s system, provided you have correctly configured the Router’s settings
for your ISP’s connection type. Your ISP connection settings are provided to you
by your ISP. To configure the Router with the settings that your ISP gave you,
click “Connection Type” (A) on the left side of the screen. Select the connection
type you use. If your ISP gave you DNS settings, clicking “DNS” (B) allows you to
enter DNS address entries for ISPs that require specific settings. Clicking “MAC
Address” (C) will let you clone your computer’s MAC address or type in a specific

F5D7234-4 v4 Wireless G Router User Manual Rev1
Page 19 of 61

WAN MAC address, if required by your ISP. When you have finished making
settings, the “Internet Status” indicator will read “Connected” if your Router is set
up properly.

Setting your Connection Type

From the “Connection Type” page, you can select the type of connection you use.
Select the type of connection you use by clicking the button (1) next to your
connection type and then clicking “Next” (2).

Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP

A dynamic connection type is the most common connection type used with cable
modems. Setting the connection type to “dynamic” in many cases is enough to
complete the connection to your ISP. Some dynamic connection types may
require a host name. You can enter your host name in the space provided if you
were assigned one. Your host name is assigned by your ISP. Some dynamic
connections may require that you clone the MAC address of the PC that was
originally connected to the modem.

Change WAN MAC Address

If your ISP requires a specific MAC address to connect to the service, you
can enter a specific MAC address or clone the current computer’s MAC
address through this link.

Setting your Internet Service Provider (ISP) Connection Type to Static IP

A static IP address connection type is less common than other connection types.
If your ISP uses static IP addressing, you will need your IP address (1), subnet
mask (2), and ISP gateway address (3). This information is available from your
ISP or on the paperwork that your ISP left with you. Type in your information,
then click “Apply Changes”. After you apply the changes, the “Internet Status”
indicator will read “Connected” if your Router is set up properly.

1. IP Address

Provided by your ISP. Enter your IP address here.

2. Subnet Mask

Provided by your ISP. Enter your subnet mask here.

3. ISP Gateway Address

Provided by your ISP. Enter the ISP gateway address here.