Beko WMB 61021 Y+ User manual [EN,ET,BG]

Washing Machine

User’s Manual

WMB 61021 Y+

Document Number=

ET BG

2820523925_EN / 02-09-15.(16:59)

1 Important nstructons for safety and envronment

This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.

1.1 General safety

• This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children of less than 3 years should be kept away unless continuously supervised.

• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.

• If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent. There is the risk of electric shock!

• This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.

• Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

• The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.

• Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.

• Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get da maged.

• Unplug the product when not in use.

• Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!

This product was manufactured using the latest technology in environmentally friendly conditions.

• Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.

• Use detergents, softeners and supplements suitable for automatic washing ma

chines only.

• Follow the instructions on the textile tags and on the detergent package.

• The product must be unplugged during installation, maintenance, cleaning and repairing procedures.

• Always have the installation and repairing procedures carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

• If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someo

ne designated by the importer in order to avoid possible risks.

• Place the product on a rigid, flat and level surface.

• Do not place it on a long-pile rug or similar surfaces.

• Do not place the product on a high platform or near the edge on a cascaded sur

face.

• Do not place the product on the power cable.

• Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces.

1.2 Intended use

• This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.

• The product must only be used for washing and rinsing of laundry that are mar ked accordingly.

• The manufacturer waives any responsibility arisen from incorrect usage or transportation.

1.3 Chldren's safety

• Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.

• Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product.

• Do not forget to close the loading door when leaving the room where the pro duct is located.

• Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.

3 / EN

Washing Machine / User’s Manual

While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the washing operation is in progress.

1.4 Package nformaton

• Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

1.5 Dsposng of the waste product

• This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product.

1.6 Complance wth WEEE Drectve

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This product has been manufactured with high quality parts and materials which can be reused and are suitable for re cycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.

Compliance with RoHS Directive:

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and pro hibited materials specified in the Directive.

4 / EN

Washing Machine / User’s Manual

2 Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

NOTE :

Preparation of the location and

electrical, tap water and waste water

installations at the place of installation is under customer's responsibility.

NOTE :

Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

DANGER:

connections of the product must be carried out

by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

CAUTION:

if the product has any defects on it. If so, do not

have it installed. Damaged products cause risks for your safety.

2.1 Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

• Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

• Do not place the product on the power cable.

• Do not install the product at places where temperature may fall below 0ºC.

• Place the product at least 1 cm away from the edges of other furniture.

Installation and electrical

Prior to installation, visually check

2.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

2.3 Removing the transportation locks

WARNING:

locks before taking out the packaging

reinforcement.

WARNING:

bolts before operating the washing machine! Otherwise, the product will be damaged.

1. Loosen all the bolts with a suitable spanner until they rotate freely

Do not remove the transportation

Remove the transportation safety

(C)

5 / EN

Washing Machine / User’s Manual

2. Remove transportation safety bolts by turning them gently.

3. Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel.

NOTE :

Keep the transportation safety bolts in

a safe place to reuse when the washing machine

needs to be moved again in the future.

NOTE :

Never move the product without the

transportation safety bolts properly fixed in place!

(P)

2.4 Connecting water supply

NOTE :

The water supply pressure required to

run the product is between 1 to 10 bars (0.1 – 1

MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.

NOTE :

If you are going to use the double waterinlet product as a single you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)

WARNING:

should not be connected to the hot water tap. In

such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

WARNING:

hoses on the new product. It may cause stains on your laundry.

Models with a single water inlet

Do not use old or used water inlet

(cold)

water-inlet unit,

1. Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.

CAUTION:

connections are made correctly when installing

the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.

2. Tighten all hose nuts by hand. Never use a tool when tightening the nuts.

3. Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

Ensure that the cold and hot water

6 / EN

Washing Machine / User’s Manual

2.5 Connecting to the drain

• The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

CAUTION:

hose comes out of its housing during water

discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.

• The hose should be attached to a height of at least 40 cm, and 100 cm at most.

• In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.

• To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.

• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.

• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

Your house will be flooded if the

100cm

40cm

2.6 Adjusting the feet

CAUTION:

operates more silently and vibration-free,

it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.

1. Loosen the lock nuts on the feet by hand.

2. Adjust the feet until the product stands level and balanced.

3. Tighten all lock nuts again by hand.

WARNING:

lock nuts. Otherwise, they will get damaged.

In order to ensure that the product

Do not use any tools to loosen the

2.7 Electrical connection

Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

• Connection must comply with national regulations.

• Power cable plug must be within easy reach after installation.

• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse.

• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.

• Do not make connections via extension cables or multi-plugs.

DANGER:

replaced by the Authorized Service Agents.

Transportation of the product

1. Unplug the product before transporting it.

2. Remove water drain and water supply connections.

3. Drain all water that has remained in the product.

4. Install transportation safety bolts in the reverse order of removal procedure;

NOTE :

transportation safety bolts properly fixed in

place!

Damaged power cables must be

Never move the product without the

7 / EN

Washing Machine / User’s Manual

CAUTION:

to children. Keep packaging materials in a safe

place away from reach of the children.

Packaging materials are dangerous

3 Preparation

3.1 Sorting the laundry

• Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.

• Always obey the instructions given on the garment tags.

3.2 Preparing laundry for washing

• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.

• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.

• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.

• Place curtains in without compressing them. Remove curtain attachment items.

• Fasten zippers, sew loose buttons and mend rips and tears.

• Wash “machine washable” or “hand washable” labeled products only with an appropriate programme.

• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately.

• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.

• Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the instructions on the package.

• Wash trousers and delicate laundry turned inside out.

• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling.

• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.

3.3 Things to be done for energy saving

Following information will help you use the product in an ecological and energy-efficient manner.

• Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and

consumption table".

• Always follow the instructions on the detergent packaging.

• Wash slightly soiled laundry at low temperatures.

• Use faster programmes for small quantities of lightly soiled laundry.

• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.

• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process.

• Do not use detergent in excess of the amount recommended on the detergent package.

3.4 Initial use

Before starting to use the product, make sure that all preparations are made in accordance with the instructions in sections “Important safety instructions” and “Installation”. To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If your product is not equipped with Drum Cleaning programme, perform the Initial Use procedure in accordance with the methods described under “5.2 Cleaning the loading door and the drum” section of the user manual.

NOTE :

Use an anti-limescale suitable for the

washing machines.

NOTE :

Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.

3.5 Correct load capacity

The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. The machine automatically adjusts the amount of water according to the weight of the loaded laundry.

CAUTION:

“Programme and consumption table”. When

overloaded, machine's washing performance will drop. Moreover, noise and vibration problems may occur.

Follow the information in the

3.6 Loading the laundry

1. Open the loading door.

2. Place laundry items loosely into the machine.

3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.

NOTE :

The loading door is locked while a

programme is running. The door can only be

opened a while after the programme comes to an end.

8 / EN

Washing Machine / User’s Manual

CAUTION:

noise and vibration problems may occur in the

machine.

In case of misplacing the laundry,

3.7 Using detergent and softener

NOTE :

When using detergent, softener, starch,

fabric dye, bleach or limescale remover read the

manufacturer's instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.

Detergent Drawer

The detergent drawer is composed of three compartments: – (1) for prewash – (2) for main wash – (3) for softener – (*) in addition, there is siphon piece in the softener compartment.

Detergent, softener and other cleaning agents

• Add detergent and softener before starting the washing programme.

• Never leave the detergent drawer open while the washing programme is running!

• When using a programme without prewash, do not put any detergent into the prewash compartment (compartment nr. "1").

• In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment nr. "1").

• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the machine.

• If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash compartment (compartment nr. "2").

Choosing the detergent type

The type of detergent to be used depends on the type and colour of the fabric.

• Use different detergents for coloured and white laundry.

• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely for delicate clothes.

• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.

• Wash woolens with special detergent made specifically for woolens.

CAUTION:

specifically for washing machines.

CAUTION:

Adjusting detergent amount

The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

• Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.

• Use lesser detergent for small amounts or lightly soiled clothes.

Using softeners

Pour the softener into the softener compartment of the detergent drawer.

• Do not exceed the (>max<) level marking in the softener compartment.

• If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.

Using liquid detergents If the product contains a liquid detergent cup:

• Make sure that you have placed the liquid detergent cup in compartment nr. "2".

• If the lqud detergent has lost ts fludty, dlute t wth water before puttng n the detergent cup.

Use only detergents manufactured

Do not use soap powder.

9 / EN

Washing Machine / User’s Manual

Heavly Soled

(difficult stains such as grass, coffee, fruits and blood.)

Normally Soled

(For example,

Soiling Level

stains caused by body on collars and cuffs)

Lghtly Soled

(No visible stains exist.)

Heavly Soled

Normally Soled

Soiling Level

Lghtly Soled

Clothes

Lght colours and whtes

(Recommended temperature range based on soiling level: 40-90 °C)

It may be necessary to pre-treat the stains or perform prewash. Powder and liquid detergents recommended for whites can be used at dosages recommended for heavily soiled clothes. It is recommended to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches.

Powder and liquid detergents recommended for whites can be used at dosages recommended for normally soiled clothes.

Powder and liquid detergents recommended for whites can be used at dosages recommended for lightly soiled clothes.

Colours

(Recommended temperature range based on soiling level: cold -40 °C)

Powder and liquid detergents recommended for colours can be used at dosages recommended for heavily soiled clothes. It is recommended to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches. Use detergents without bleach.

Powder and liquid detergents recommended for colours can be used at dosages recommended for normally soiled clothes. Use detergents without bleach.

Powder and liquid detergents recommended for colours can be used at dosages recommended for lightly soiled clothes. Use detergents without bleach.

Heavly Soled

Normally Soled

Soiling Level

Lghtly Soled

Heavly Soled

Normally Soled

Soiling Level

Lghtly Soled

Clothes

Dark colours

(Recommended temperature range based on soiling level: cold -40 °C)

Liquid detergents suitable for colours and dark colours can be used at dosages recommended for heavily soiled clothes.

Liquid detergents suitable for colours and dark colours can be used at dosages recommended for normally soiled clothes.

Liquid detergents suitable for colours and dark colours can be used at dosages recommended for lightly soiled clothes.

Delicates/Woollens/Silks

(Recommended temperature range based on soiling level: cold -30 °C)

Prefer liquid detergents produced for delicate clothes. Woollen and silk clothes must be washed with special woollen detergents.

10 / EN

Washing Machine / User’s Manual

If the product does not contain a liquid detergent cup:

• Do not use liquid detergent for the prewash in a programme with prewash.

• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use the Delayed Start function, do not use liquid detergent.

Using gel and tablet detergent

Apply the following instructions when using tablet, gel and similar detergents.

• If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup, put the gel detergent into the main wash detergent compartment during first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the programme.

• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum before washing.

• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the drum before washing.

NOTE :

Tablet detergents may leave residues

in the detergent compartment. If you encounter

such a case, place the tablet detergent between the laundry, close to the lower part of the drum in future washings.

NOTE :

Use the tablet or gel detergent without

selecting the prewash function.

Using starch

• Add liquid starch, powder starch or the fabric dye into the softener compartment.

• Do not use softener and starch together in a washing cycle.

• Wipe the inside of the machine with a damp and clean cloth after using starch.

Using bleaches

• Select a programme with prewash and add the bleaching agent at the beginning of the prewash. Do not put detergent in the prewash compartment. As an alternative application, select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step.

• Do not use bleaching agent and detergent by mixing them.

• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes.

• When using oxygen based bleaches, select a programme that washes at a lower temperature.

• Oxygen based bleaches can be used together with detergents; however, if its thickness is not the same with the detergent, put the detergent first into the compartment nr. "2" in the detergent drawer and wait until the detergent flows while the machine is taking in water. Add the bleaching agent from the same compartment while the machine is still taking in water.

Using limescale remover

• When required, use limescale removers manufactured specifically for washing machines only.

11 / EN

Washing Machine / User’s Manual

4 Operatng the product

1 2

4.1 Control panel

1 - Programme Selecton knob (Uppermost poston On/Off) 2 - Programme Follow-up ndcator 3 - Temperature Adjustment button 4 - Spn Speed adjustment button 5 - Auxlary Functon buttons 6 - Delayed Start button (n some models) 7 - Start / Pause button

76543

Dark wash

(Darkcare)

Drain

(Pump)

Daily

express

Mixed 40

(Mix40)

12 / EN

Dark wash

(Darkcare)

creasing

Rinse hold Start/

Super 40 Extra rinse

Synthetics

Anti-

(Bedding)

(Rinse Plus)

Cottons Pre-wash Main

Pause

Child-

proof lock

No spin Quick

Freshen

Duvet

Hand Wash

wash

Shirts

wash

BabyProtect Cotton

Finished Cold

Jeans Sport Time delay Intensive

Rinse Wash Spin

Woollens

Eco

Temperature

expres 14

Super short

express

Self

Clean

Delicate Pet hair

Daily

Lingerie

Fasihon

care

removal

mini 30

Eco Clean

Anti-

allergic

Door Ready

On/Off

BabyProtect +

PHR +

Washing Machine / User’s Manual

4.2 Preparng the machne

Make sure that the hoses are connected tghtly. Plug n your machne. Turn the tap on completely. Place the laundry n the machne. Add detergent and fabrc softener.

4.3 Programme selecton

Select the programme sutable for the type, quantty and solng degree of the laundry n accordance wth the “Programme and consumpton table” and the temperature table below.

90˚C

60˚C

40˚C30˚CCold

Select the desred programme wth the Programme Selecton button.

C C C C

Heavily soiled white cottons and linens. (coffee table covers, tableclothes, towels, bed sheets, etc.)

Normally soiled, coloured, fade proof linens, cottons or synthetic clothes (shirt, nightgown, pajamas, etc.) and lightly soiled white linens (underwear, etc.)

Blended laundry including delicate textile (veil curtains, etc.), synthetics and woolens.

Programmes are limited with the highest spin speed appropriate for that particular type of fabric.

When selecting a programme, always consider the type of fabric, colour, degree of soiling and permissible water temperature.

Always select the lowest required temperature. Higher temperature means higher power consumption.

For further programme details, see "Programme and consumption table"

4.4 Main programmes

Depending on the type of fabric, use the following main programmes.

• Cottons

Use this programme for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle.

• Synthetics

Use this programme to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a gentle action and has a shorter washing cycle compared to the Cottons programme. For curtains and tulle, use the Synthetic 40˚C programme with prewash and anti-creasing functions selected. As their meshed texture causes excessive foaming, wash the veils/tulle by putting little amount of detergent into the main wash compartment. Do not put detergent in the prewash compartment.

• Woollens

Use this programme to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woolens.

4.5 Additional programmes

For special cases, additional programmes are available in the machine.

Additional programmes may differ according to the model of the machine.

• Cotton Economic

You may wash your normally soled durable cotton and lnen laundry n ths programme wth the hghest energy and water savng compared to all other wash programmes sutable for cottons. Actual water temperature may dffer from the declared cycle temperature. Programme duraton may automatcally be shortened durng later stages of the programme f you wash less amount (e.g. ½ capacty or less) of laundry. In ths case energy and water consumpton wll be further decreased gvng you the opportunty for a more economcal wash. Ths feature s avalable for certan models havng remanng tme dsplay.

• BabyProtect

Use ths programme to wash baby laundry, and the laundry that belongs to allergc persons. Longer heatng tme and an addtonal rnsng step provde a hgher level of hygene.

• Delicate

Use this programme to wash your delicate clothes. It washes with a gentle action without any interim spin compared to the Synthetics programme.

• Hand wash

Use ths programme to wash your woolen/delcate clothes that bear “not machne- washable” tags and for whch hand wash s recommended. It washes laundry wth a very gentle washng acton to not to damage clothes.

13 / EN

Washing Machine / User’s Manual

• Daily express

Use ths programme to quckly wash your lttle amount of lghtly soled cotton clothes.

• Super short express

Use this programme to wash your little amount of lightly soiled cotton clothes in a short time.

• Darkcare

Use ths programme to wash your dark coloured laundry, or the coloured laundry that you do not want them get faded. Washng s performed wth less mechancal movements at low temperature. It s recommended to use lqud detergent or wool shampoo for dark coloured laundry.

• Mixed 40 (Mix 40)

Use this programme to wash your cotton and synthetic clothes together without sorting them.

• Shirts

Use this programme to wash the shirts made of cotton, synthetic and synthetic blended fabrics together.

• Sports

Use this programme to wash your garments that are worn for a short time such as sportswear. It is suitable to wash little amount of cotton / synthetic blended garments.

4.6 Special programmes

For specific applications, select any of the following programmes.

• Rinse

Use this programme when you want to rinse or starch separately.

• Spin + Drain

Use this programme to apply an additional spin cycle for your laundry or to drain the water in the machine. Before selecting this programme, select the desired spin speed and press Start / Pause button. First, the

machine will drain the water inside of it. Then, it will spin the laundry with the set spin speed and drain the water coming out of them. If you wish to drain only the water without spinning your laundry, select the Pump+Spin programme and then select the No Spin function with the help of Spin Speed Adjustment button. Press Start / Pause button.

Use a lower spin speed for delicate laundries.

4.7 Temperature selection

Whenever a new programme is selected, the maximum temperature for the selected programme appears on the temperature indicator. To decrease the temperature, press the Temperature Adjustment button. Temperature will decrease gradually.

If the programme has not reached the heating step, you can change the temperature without

switching the machine to Pause mode.

4.8 Spin speed selection

Whenever a new programme is selected, the recommended spin speed of the selected programme is displayed on the spin speed indicator. To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases gradually. Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the display. See "Auxiliary function selection" section for explanations of these options.

If the programme has not reached the spinning

step, you can change the speed without switching the machine to Pause mode.

Indcatve values for Synthetcs programmes (EN)

Remanng Mosture

Content (%) **

Load (kg)

Water

Consumpton

(l)

Energy

Consumpton

(kWh)

Programme

Duraton

Synthetcs 60

Synthetcs 40

* You can see the washng tme of the programme you have selected on the dsplay of the machne. It s normal that small dfferences may occur between the tme shown on the dsplay and the real washng tme.

** Remanng mosture content values may dffer accordng to the selected spn speed.

14 / EN

2.5 45 0.90 01:56 45 40

2.5 45 0.42 01:46 45 40

≤ 1000 rpm > 1000 rpm

(mn) *

Washing Machine / User’s Manual

Remanng Mosture

Content (%) **

4.9 Programme and consumption table

Auxiliary functions

Rinse Hold

Pet hair removal

Temperature

Programme

Max. Load (kg)

Programme Duration (~min)

Water Consumption (l)

Energy Consumption (kWh)

60** 6 210 44 1.02 1600 • 40-60

Cotton Economic

Cottons

Synthetics

Daily express

Super short express 30 2 14 40 0.11 1400 • • Cold-30 BabyProtect 90 6 165 85 1.90 1600 • * • 30-90 Sports 40 3 101 48 0.45 800 • • • • • Cold-40 Delicate 30 2 59 43.13 0.23 600 • • • Cold-40 Hand wash 20 1 43 30 0.15 600 20 Woollens 40 1.5 60 40 0.30 600 • • Cold-40 Darkwash 40 2.5 107 58 0.45 800 * • Cold-40 Shirts 60 2.5 104 55 0.90 600 • • • * • Cold-60 Mix40 40 3 115 45 0.50 800 • • • • • • Cold-40

60** 3 173 33 0.68 1600 • 40-60 40** 3 173 33 0.68 1600 • 40-60

90 6 147 66 2.25 1600 • • • • • • Cold-90 60 6 118 66 1.45 1600 • • • • • • Cold-90 40 6 98 66 0.85 1600 • • • • • • Cold-90 60 2.5 116 45 0.90 800 • • • • • • Cold-60 40 2.5 106 45 0.42 800 • • • • • • Cold-60 90 6 88 55 1.90 1400 • • Cold-90

60 6 58 55 1.00 1400 • • Cold-90 30 6 28 55 0.20 1400 • • Cold-90

Max. Speed***

Prewash

Quick Wash

Rinse Plus

Anti-Creasing

• : Selectable * : Automatically selected, no canceling. ** : Energy Label programme (EN 60456 Ed.3) *** : If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.

** “Cotton eco 40°C and Cotton eco 60°C are standard cycles.” These cycles are known as ‘40°C cotton standard cycle’ and ‘60°C cotton standard cycle’ and indicated with the symbols on the panel.

The auxiliary functions in the table may vary according to the model of your machine.

Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed,

and changes in electric voltage. You can see the washing time of the programme you have selected on the display of the machine. It is normal

that small differences may occur between the time shown on the display and the real washing time.

“Selectability of auxiliary functions might be changed by the manufacturer. New selectabilities might be added or existing ones might be removed.” «The spin speed of your machine may vary among the programmes, however this speed cannot exceed the max. spin speed of your machine.»

15 / EN

Washing Machine / User’s Manual

4.10 Auxlary functon selecton

Use the followng auxlary functons accordng to your daly needs. Select the desred auxlary functons before startng the programme. Furthermore, you may also select or cancel auxlary functons that are sutable to the runnng programme wthout pressng the Start / Pause button when the machne s operatng. For ths, the machne must be n a step before the auxlary functon you are gong to select or cancel. If the auxlary functon cannot be selected or canceled, lght of the relevant auxlary functon wll blnk 3 tmes to warn the user.

Some functions cannot be selected together. If a second auxiliary function conflicting with the

first one is selected before starting the machine, the function selected first will be canceled and the second auxiliary function selection will remain active. For example, if you want to select Quick Wash after you have selected the Prewash, Prewash will be canceled and Quick Wash will remain active.

An auxiliary function that is not compatible with the programme cannot be selected. (See

“Programme and consumption table”)

Auxiliary Function buttons may vary according to the model of the machine.

• Prewash

A Prewash s only worthwhle for heavly soled laundry. Not usng the Prewash wll save energy, water, detergent and tme.

Prewash without detergent is recommended for tulle and curtains.

• Quick Wash

Ths functon can be used n Cottons and Synthetcs programmes. It decreases the washng tmes and also the number of rnsng steps for lghtly soled laundry.

When you select this function, load your machine with half of the maximum laundry specified in

the programme table.

• Rnse Plus

Ths functon enables the machne to make another rnsng n addton to the one already made after the man wash. Thus, the rsk for senstve skns (babes, allergc skns, etc.) to be effected by the mnmal detergent remnants on the laundry can be reduced.

• Anti-Creasing

Ths functon creases the clothes lesser when they are beng washed. Drum movement s reduced and spnnng speed s lmted to prevent creasng. In addton, washng s done wth a hgher water level. Use ths functon for delcate laundry that creases easly.

• Rinse Hold

If you are not gong to unload your clothes mmedately after the programme completes, you may use rnse hold functon to keep your laundry n the fnal rnsng water n order to prevent them from gettng wrnkled when there s no water n the machne. Press Start / Pause button after ths process f you want to dran the water wthout spnnng your laundry. Programme wll resume and complete after dranng the water. If you want to spn the laundry held n water, adjust the Spn Speed and press Start / Pause button. The programme resumes. Water s draned, laundry s spun and the programme s completed.

Delayed Start

Wth the Delayed Start functon the startup of the programme may be delayed up to 3, 6 or 9 hours.

Open the loadng door, place the laundry and put detergent, etc. Select the washng programme, temperature, spn speed and, f requred, the auxlary functons. Set the desred tme by pressng the Delayed Start button. When the button s pressed once, 3 hours delayed start s selected. When the same button s pressed agan, 6 hours delay s selected, and when t s pressed for the thrd tme, 9 hours delayed start s selected. If you press the Delayed Start button once agan, Delayed Start functon wll be canceled. Press Start / Pause button. Prevous delayed start tme lght turns off and next delayed start tme lght turns on after every 3 hours. At the end of the countdown, all delayed start lghts wll turn off and the selected programme wll start.

Changing the Delayed Start period

Press Delayed Start button. Every tme the button s pressed, the perod wll change n 3-hour ncrements and the lght of the selected delayed start tme wll turn on.

(In some models only)

Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the

clothes.

Additional laundry may be loaded during the delayed start period.

16 / EN

Washing Machine / User’s Manual

Canceling the Delayed Start function

If you want to cancel the delayed start countdown and start the programme mmedately: Set the Delayed Start perod to zero (all delayed start perod lghts wll turn off) or turn the Programme Selecton knob to any programme. Thus, Delayed Start functon wll be canceled. The End/Cancel lght flashes contnuously. Then, select the programme you want to run agan. Press Start / Pause button to start the programme.

4.11 Startng the programme

Press Start / Pause button to start the programme. Programme follow-up lght showng the startup of the programme wll turn on.

If no programme is started or no key is pressed within 1 minute during programme selection

process, the machine will switch to Pause mode and the illumination level of the temperature, speed and loading door indicator lights will decrease. Other indicator lights and indicators will turn off. Once the Programme Selection knob is rotated or any button is pressed, indicator lights and indicators will turn on again.

4.12 Chld Lock

Use chld lock functon to prevent chldren from tamperng wth the machne. Thus you can avod any changes n a runnng programme.

If the Programme Selection knob is turned when the Child Lock is active, “Con” appears on

the display. The Child Lock does not allow any change in the programmes and the selected temperature, speed and auxiliary functions.

Even if another programme is selected with the Programme Selection knob while the Child Lock

is active, previously selected programme will continue running.

When the Child Lock is active and the machine is running, you can switch the machine to Pause

mode without deactivating the Child Lock by turning the Programme Selection knob to On / Off position. When you turn the Programme Selection knob afterwards, the programme will resu

To activate the Child Lock:

Press and hold 1st and 2nd Auxlary Functon buttons for 3 seconds. The lghts on the 1st and 2nd Auxlary Functon buttons wll flash whle you keep the buttons pressed for 3 seconds.

To deactivate the Child Lock:

Press and hold 1st and 2nd auxlary functon buttons for 3 seconds whle any programme s runnng. The lghts on the 1st and 2nd Auxlary Functon buttons wll flash whle you keep the buttons pressed for 3 seconds.

In addition to the method above, to deactivate the Child Lock, switch the Programme Selection

knob to On / Off position when no programme is running, and select another programme.

When the power is restored after a power failure or after your machine is unplugged and plugged

in again, the Child Lock will not be deactivated when the machine resumes operating.

4.13 Progress of programme

Progress of a runnng programme can be followed from the Programme Follow-up ndcator. At the begnnng of every programme step, the relevant ndcator lght wll turn on and lght of the completed step wll turn off. You can change the auxlary functons, speed and temperature settngs wthout stoppng the programme flow whle the programme s runnng. To do ths, the change you are gong to make must be n a step after the runnng programme step. If the change s not compatble, relevant lghts wll flash for 3 tmes.

If the machine does not pass to the spinning step, Rinse Hold function might be active or the

automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine.

4.14 Loadng door lock

There s a lockng system on the loadng door of the machne that prevents openng of the door n cases when the water level s unsutable. Loadng door lght wll start flashng when the machne s swtched to Pause mode. Machne checks the level of the water nsde. If the level s sutable, Loadng Door lght llumnates steadly wthn 1-2 mnutes and the loadng door can be opened. If the level s unsutable, Loadng Door lght turns off and the loadng door cannot be opened. If you are oblged to open the Loadng Door whle the Loadng Door lght s off, you have to cancel the current programme; see “Cancelng the programme”.

17 / EN

Washing Machine / User’s Manual

Changng the selectons after programme has started

Switching the machine to pause mode

Press the Start / Pause button to swtch the machne to pause mode whle a programme s runnng. The lght of the step whch the machne s n starts flashng n the Programme Follow-up ndcator to show that the machne has been swtched to the pause mode. Also, when the loadng door s ready to be opened, Loadng Door lght wll also llumnate contnuously n addton to the programme step lght.

Changing the speed and temperature settings for auxiliary functions

Dependng on the step the programme has reached, you may cancel or actvate the auxlary functons; see, “Auxlary functon selecton”. You may also change the speed and temperature settngs; see, “Spn speed selecton” and “Temperature selecton”.

If no change is allowed, the relevant light will flash for 3 times.

4.15 Addng or takng out laundry

Press the Start / Pause button to swtch the machne to pause mode. The programme follow-up lght of the relevant step durng whch the machne was swtched nto the pause mode wll flash. Wat untl the Loadng Door can be opened. Open the Loadng Door and add or take out the laundry. Close the Loadng Door. Make changes n auxlary functons, temperature and speed settngs f necessary. Press Start / Pause button to start the machne.

4.16 Cancelng the programme

To cancel the programme, turn the Programme Selecton knob to select another programme. Prevous programme wll be canceled. End / Cancel lght wll flash contnuously to notfy that the programme has been canceled. Your machne wll end the programme when you turn the Programme Selecton knob; however, t does not dran the water nsde. When you select and start a new programme, the newly selected programme wll start dependng on the step the prevous programme was canceled n. For example, t may take n addtonal water or contnue to wash wth the water nsde.

Depending on the step where the programme was canceled in, you may have to put detergent

and softener again for the programme you have selected anew.

4.17 Your machne s equpped wth a

“Standby Mode”

In case of not startng any programme or watng wthout makng any other operaton when the machne s turned on by On/Off button and whle t s n selecton step or f no other operaton s performed approxmately 2 mnutes after the programme you selected has come to an end, your machne wll automatcally swtch to energy savng mode. Dsplay brghtness wll decrease. In case of rotatng the Programme Selecton knob or pressng any button, lghts wll restore to ther prevous condton. Ths s not a fault.

18 / EN

Washing Machine / User’s Manual

5 Maintenance and cleaning

Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.

5.1 Cleaning the detergent drawer

Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time.

1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.

NOTE :

If more than normal amount of water

and softener mixture starts to gather in the

softener compartment, the siphon must be cleaned.

2. Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning.

3. Insert the drawer back into its place after cleaning and make sure that it is seated well.

If your detergent drawer s the one ndcated n the followng fgure:

NOTE :

Lift the rear part of the siphon to

remove it as illustrated. After performing the

above mentioned cleaning procedures, replace the siphon back to its seating and push its front section downwards to make sure that the locking tab engages.

5.2 Cleanng the loadng door and the drum

For products with drum cleaning programme, please see Operating the product - Programmes. For products without drum cleaning, follow the below steps Select functions. Use a Cottons pre-wash. Set

recommended on the drum cleaning agent which can be provided from authorized services.

this procedure Before starting the programme, put 1 pouch of special drum cleaning agent (if the special agent could not be supplied, put max. 100 g of powder anti-limescale) into the main wash detergent compartment (compartment no. “2”). If the antilimescale is in tablet form, put only one tablet into the main wash compartment no. “2”. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end.

After every washing make sure that no foreign substance is left in the drum.

to clean the drum:

Additional Water

the temperature to the level

without any laundry in the product.

NOTE :

Repeat Drum Cleaning process in every

2 months.

NOTE :

Use an anti-limescale suitable for the

washing machines.

Extra Rinse

programme

auxiliary

without

Apply

19 / EN

Washing Machine / User’s Manual

If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick.

NOTE :

Foreign metal substances will cause rust

stains in the drum. Clean the stains on the drum

surface by using cleaning agents for stainless steel. Never use steel wool or wire wool.

CAUTION:

These will damage the painted and plastic

surfaces.

Never use sponge or scrub materials.

5.3 Cleaning the body and control panel

Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary, and dry with a soft cloth. Use only a soft and damp cloth to clean the control panel.

5.4 Cleaning the water intake filters

There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty.

off first to clean the pump filter. In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely.

CAUTION:

filter may damage your machine or may cause

noise problem.

In order to clean the dirty filter and discharge the water:

1. Unplug the machine to cut off the supply power.

CAUTION:

machine may rise up to 90 ºC. To avoid burning

risk, filter must be cleaned after the water in the machine cools down.

2. Open the filter cap. If the filter cap is composed of two pieces, press

the tab on the filter cap downwards and pull the piece out towards yourself.

Foreign substances left in the pump

Temperature of the water inside the

1. Close the taps.

2. Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.

3. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.

4. Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.

5.5 Draining remaining water and cleaning

the pump filter

The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend. If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained

20 / EN

If the filter cap is one piece, pull the cap from both sides at the top to open.

NOTE :

You can remove the filter cover by slightly

pushing downwards with a thin plastic tipped

tool, through the gap above the filter cover. Do not use metal tipped tools to remove the cover.

3. Some of our products have emergency draining hose and some does not have. Follow the steps below to discharge the water.

Washing Machine / User’s Manual

Discharging the water when the product has an emergency draining hose:

a. Pull the emergency draining hose out from its seat b. Place a large container at the end of the hose.

Drain the water into the container by pulling out the plug at the end of the hose. When the container is full, block the inlet of the hose by replacing the plug. After the container is emptied, repeat the above procedure to drain the water in the machine completely.

c. When draining of water is finished, close the end

by the plug again and fix the hose in its place.

d. Turn the pump filter to take it out.

Discharging the water when the product does not have an emergency draining hose:

a. Place a large container in front of the filter to catch

water from the filter.

b. Loosen pump filter (anticlockwise) until water

starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any spilled water.

c. When the water inside the machine is finished,

take out the filter completely by turning it.

4. Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.

5. Install the filter.

6. If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat the tabs in the lower part into their places first, and then press the upper part to close.

21 / EN

Washing Machine / User’s Manual

+ 47 hidden pages