Beko WMA 665 S, WMA 665 W, WMA 645 W, WMA 645 S, WMA 655 W Owner's Manual

...

Automatic washing machine

installation & operating

instructions and washing guidance

WMA 665 S WMA 665 W WMA 645 W WMA 645 S WMA 655 W WMA 655 S

contents

Introduction

Welcome 2

Installation

Know your washing machine/specification 4

Location 5

Installation 5

Electrical connection 7

Operating

How to use 8

Programme descriptions 12

Function buttons 13

ITCL fabric care symbols 13

Machine care

Care & maintenance 14

Before calling service/trouble shooting 16

Guarantee 17

Service 17

know your washing machine

Capacity (dry fabric) 6kg Dimensions width x depth x height

60cm x 54cm x 85cm Net weight 72kg Supply voltage 230V~ 50Hz Nominal current 10A Motor power 350 watts Heater power 2100 watts Washing speed 52 rpm Spin speed 1600 rpm

(Model Dependent)

Because we continually strive to improve our products, we may change our specifications and designs without prior notice.

specification

Kick plate cover

Front door

Kick plate

Top lid

Function buttons

Spin speed selection

Time delay adjustment button

Start/Pause/Cancel button

Remain time

Prewash

button

Detergent and softener drawer

On/Off button

Door open button

Quick

wash

button

Extra Rinse

button

Anti-

Crease

button

programme selection knob

Door Handle

Removing transport safety bolts

The transport safety bolts must be removed

before any operation of the machine.

1 Turn the bolt heads C anti-clockwise until

the bolt can be partially withdrawn.

2 Remove them and the rubber bushes by

pulli

ng outwards. An up/down action and a small squirt of washing up liquid will ease removal.

Plastic plugs, supplied inside the protective

bag, designated P, should be placed in the safety bolt holes as shown.

Attention!

Keep the safety bolts for future transportation and reinstate them before transporting your machine. Never transport your machine without the transport bolts in position. Any resultant damage is not covered by the warranty.

location

You can locate the washing machine anywhere (except bathrooms, showers and away from rain, damp places and water) as long as you have hot and cold water supply, drainage and electrical connection alongside.

Ensure there is clearance each side of the machine to allow slight side ways movement during washing and spin drying.

Attention!

Never place your machine on a carpet. This prevents air circulation. The electrical components of the machine may overheat and may cause damage.

Please ensure the power, water supplies and waste are suitable, if in doubt, consult a qualified plumber or electrician.

In the case of floating, or any form of suspended floor, the flooring joists must be constructed in a way to fully support machines that, when loaded, can exceed a weight of 90kgs, and therefore the area directly beneath the appliance must be additionally supported directly from the sub-floor in a way to adequately prevent excessive vibration and movement on the machine’s spin cycle.(Please see diagram 1)

In addition to this, washing mach

ines should not be installed on carpet, foam backed laminate, or parquet flooring where the nature of these types of flooring can also contribute to the inefficient operation of the washing machine on the spin cycle.

installation

Drain hose

The drain hose should be placed and secured either at the side of the sink A, directly to the drain B or directly to the waste water inlet C.

• The hose should not be bent.

• Using method A, the drain hose should be

secured with the elbow so that it can not be dislodged.

• The waste pipe must only be connected

into the foul drains and not surface water drainage system.

• The hose should be placed between 20 and

80cm from the floor level and must not be extended otherwise the machine may not empty the waste water.

• The m

inimum diameter of any external pipe

must be 32 mm.

Water inlet connection

Your machine comes with cold water

connection only.

Connect the cold water using the hose with

blue printing or colour.

Cold water supply

For proper operation, the pressure of cold water should be between 1 and 10 bars. (1 bar corresponds to more than 8 litres per minute flow rate with a fully open tap.)

To prevent water leaks, sealing washers are supplied with the water inlet hose inside the machine. Place these on the hose end and tighten both ends fully.

In order to prevent any water leakage and damage, turn off the water tap when not in use. Connect the cornered end of the hose to the machine water inlet.

The washing machine should be connected via new hose sets and the old hose sets should not be reused.

min.

Feet adjustment

To ensure quiet and stable operation, the machine should be positioned correctly and on the level. If the machine is unstable, adjust one of the front feet by loosening the plastic lock nut and screwing or unscrewing the foot until the machine is level. After positioning, tighten the lock nut.

+ 12 hidden pages