Dear Customer,
We hope that you get the best results from the product which has been manufactured
in state-of-the-art plants and passed through a strict quality control procedure.
Therefore, please read the entire user manual carefully before using the product and
keep it as a reference for future use. In case of transferring the product to someone
else, give the manual as well.
The user manual will help you use your machine in a fast
and safe way.
• Read the user manual before installing and starting your product.
• Always follow the safety instructions.
• Keep this user manual within easy reach for future reference.
• Read also the other documents supplied with the product.
Remember that this user manual is also applicable for several other models. Differences
between models will be identified in the manual.
Explanation of symbols
Throughout this user manual the following symbols are used:
C Important information or useful hints about usage.
A Warning for hazardous situations with regard to life and property.
B Warning for electric shock.
2820522003/080411.1430
This appliance’s packaging material is recyclable. Help recycle it and protect
the environment by dropping it off in the municipal receptacles provided for this
purpose. Your appliance also contains a great amount of recyclable material.
It is marked with this label to indicate the used appliances that should not be
mixed with other waste. This way, the appliance recycling organised by your
manufacturer will be done under the best possible conditions, in compliance
with European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment. Contact your town hall or your retailer for the used appliance
collection points closest to your home. We thank you doing your part to
protect the environment.
1- Power cable
2- Top panel
3- Control panel
4- Filter cap
5- Adjustable feet
6- Loading door
7- Detergent drawer
8- Drain hose
4
EN
Technical specifications
Models
Maximum dry laundry capacity (kg)
Height (cm)
Width (cm)
Depth (cm)
Net weight (±4 kg.)
Electrical input (V/Hz)
Total current (A)
Total power (W)
Spin speed (rpm max.)
Stand-by mode power (W)
Off-mode power (W)
WMB61631W
6
84
60
50
69
230 V / 50Hz
10
2200
1600
1.00
0.25
Technical specifications may be changed without prior notice to improve the quality
C
of the product.
Figures in this manual are schematic and may not match the product exactly.
C
Values stated on the product labels or in the documentation accompanying it
C
are obtained in laboratory conditions in accordance with the relevant standards.
Depending on operational and environmental conditions of the product, these
values may vary.
5
EN
2 Important safety instructions
This section contains safety instructions
that will help protect from risk of personal
injury or property damage. Failure to
follow these instructions shall void any
warranty.
General safety
• This product should not be used
by persons with physical, sensory
or mental disorders or unlearned
or inexperienced people (including
children) unless they are attended by
a person who will be responsible for
their safety or who will instruct them
accordingly for use of the product.
• Never place the product on a carpet-
covered floor; otherwise, lack of
airflow beneath the machine will
cause electrical parts to overheat.
This will cause problems with your
product.
• Do not operate the product if the
power cable / plug is damaged. Call
the Authorized Service Agent.
• Have a qualified electrician connect
a 16-Ampere fuse to the installation
location of the product.
• If the product has a failure, it should
not be operated unless it is repaired
by the Authorized Service Agent.
There is the risk of electric shock!
• This product is designed to resume
operating in the event of powering
on after a power interruption. If you
wish to cancel the programme, see
"Cancelling the programme" section.
• Connect the product to a grounded
outlet protected by a fuse complying
with the values in the "Technical
specifications" table. Do not neglect
to have the grounding installation
made by a qualified electrician. Our
company shall not be liable for any
damages that will arise when the
product is used without grounding in
accordance with the local regulations.
• The water supply and draining hoses
must be securely fastened and remain
undamaged. Otherwise, there is the
risk of water leakage.
• Never open the loading door or
remove the filter while there is still
water in the drum. Otherwise, risk of
flooding and injury from hot water will
occur.
• Do not force open the locked loading
door. The loading door will be ready
to open just a few minutes after the
washing cycle comes to an end.
In case of forcing the loading door
to open, the door and the lock
mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading
or pouring water onto it! There is the
risk of electric shock!
• Never touch the plug with wet hands!
Never unplug by pulling on the cable,
always pull out by grabbing the plug.
• Use detergents, softeners and
supplements suitable for washing
machines only.
• Follow the instructions on the textile
tags and on the detergent package.
• The product must be unplugged
during installation, maintenance,
cleaning and repairing procedures.
• Always have the installation and
repairing procedures carried out
by the Authorized Service Agent.
Manufacturer shall not be held
liable for damages that may arise
from procedures carried out by
unauthorized persons.
Intended use
• This product has been designed for
domestic use. It is not suitable for
commercial use and it must not be
used out of its intended use.
• The product must only be used for
washing and rinsing of laundry that
are marked accordingly.
• The manufacturer waives any
responsibility arisen from incorrect
usage or transportation.
Children's safety
• Electrical products are dangerous for
the children. Keep children away from
the product when it is in use. Do not
6
EN
let them to tamper with the product.
Use child lock to prevent children
from intervening with the product.
• Do not forget to close the loading
door when leaving the room where
the product is located.
• Store all detergents and additives in a
safe place away from the reach of the
children.
7
EN
3 Installation
Refer to the nearest Authorised Service
Agent for installation of the product. To
make the product ready for use, review
the information in the user manual and
make sure that the electricity, tap water
supply and water drainage systems are
appropriate before calling the Authorized
Service Agent. If they are not, call a
qualified technician and plumber to have
any necessary arrangements carried out.
Preparation of the location and
C
electrical, tap water and waste water
installations at the place of installation
is under customer's responsibility.
Installation and electrical connections
B
of the product must be carried out
by the Authorized Service Agent.
Manufacturer shall not be held
liable for damages that may arise
from procedures carried out by
unauthorized persons.
Prior to installation, visually check if
A
the product has any defects on it. If
so, do not have it installed. Damaged
products cause risks for your safety.
Make sure that the water inlet and
C
discharge hoses as well as the power
cable are not folded, pinched or
crushed while pushing the product
into its place after installation or
cleaning procedures.
Appropriate installation location
• Place the machine on a rigid floor.
Do not place it on a long pile rug or
similar surfaces.
• Total weight of the washing machine
and the dryer -with full load- when
they are placed on top of each other
reaches to approx. 180 kilograms.
Place the product on a solid and flat
floor that has sufficient load carrying
capacity!
• Do not place the product on the
power cable.
• Do not install the product at places
where temperature may fall below
0ºC.
• Place the product at least 1 cm away
from the edges of other furniture.
Removing packaging
reinforcement
Tilt the machine backwards to remove
the packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
Removing the
transportation locks
Do not remove the transportation
A
locks before taking out the packaging
reinforcement.
Remove the transportation safety
A
bolts before operating the washing
machine, otherwise, the product will
be damaged.
1. Loosen all the bolts with a spanner
until they rotate freely (C).
2. Remove transportation safety bolts by
turning them gently.
8
EN
3. Attach the plastic covers supplied in
the User Manual bag into the holes on
the rear panel. (P)
Keep the transportation safety bolts
C
in a safe place to reuse when the
washing machine needs to be moved
again in the future.
Never move the product without the
C
transportation safety bolts properly
fixed in place!
Connecting water supply
The water supply pressure required
C
to run the product is between 1 to 10
bars (0.1 – 10 MPa). It is necessary
to have 10 – 80 liters of water flowing
from the fully open tap in one minute
to have your machine run smoothly.
Attach a pressure reducing valve if
water pressure is higher.
If you are going to use the double
C
water-inlet product as a single (cold)
water-inlet unit, you must install the
supplied stopper to the hot water
valve before operating the product.
(Applies for the products supplied
with a blind stopper group.)
If you want to use both water inlets
C
of the product, connect the hot water
hose after removing the stopper and
gasket group from the hot water
valve. (Applies for the products
supplied with a blind stopper group.)
Models with a single water inlet
A
should not be connected to the hot
water tap. In such a case the laundry
will get damaged or the product will
switch to protection mode and will not
operate.
Do not use old or used water inlet
A
hoses on the new product. It may
cause stains on your laundry.
1. Connect the special hoses supplied
with the product to the water inlets
on the product. Red hose (left) (max.
90 ºC) is for hot water inlet, blue hose
(right) (max. 25 ºC) is for cold water
inlet.
Ensure that the cold and hot water
A
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end
of the washing process and wear out.
2. Tighten all hose nuts by hand. Never
use a wrench when tightening the
nuts.
3. Open the taps completely after
making the hose connection to check
for water leaks at the connection
points. If any leaks occur, turn off the
tap and remove the nut. Retighten
the nut carefully after checking the
seal. To prevent water leakages and
damages caused by them, keep the
taps closed when the machine is not
in use.
9
EN
Connecting to the drain
• The end of the drain hose must be
directly connected to the wastewater
drain or to the washbasin.
Your house will be flooded if the
A
hose comes out of its housing
during water discharge. Moreover,
there is risk of scalding due to high
washing temperatures! To prevent
such situations and to ensure smooth
water intake and discharge of the
machine, fix the end of the discharge
hose tightly so that it cannot come
out.
• The hose should be attached to a
height of at least 40 cm, and 100 cm
at most.
• In case the hose is elevated after
laying it on the floor level or close
to the ground (less than 40 cm
above the ground), water discharge
becomes more difficult and the
laundry may come out excessively
wet. Therefore, follow the heights
described in the figure.
an appropriate clamp as not to come
off and leak.
Adjusting the feet
In order to ensure that the product
A
operates more silent and vibrationfree, it must stand level and balanced
on its feet. Balance the machine by
adjusting the feet. Otherwise, the
product may move from its place
and cause crushing and vibration
problems.
• To prevent flowing of dirty water back
into the machine and to allow for easy
discharge, do not immerse the hose
end into the dirty water or drive it in
the drain more than 15 cm. If it is too
long, cut it short.
• The end of the hose should not be
bent, it should not be stepped on
and the hose must not be pinched
between the drain and the machine.
• If the length of the hose is too short,
use it by adding an original extension
hose. Length of the hose may not be
longer than 3.2 m. To avoid water leak
failures, the connection between the
extension hose and the drain hose of
the product must be fitted well with
10
1. Loosen the lock nuts on the feet by
hand.
2. Adjust the feet until the product
stands level and balanced.
3. Tighten all lock nuts again by hand.
Do not use any tools to loosen the
A
lock nuts. Otherwise, they will get
damaged.
Electrical connection
Connect the product to a grounded outlet
protected by a fuse complying with the
values in the "Technical specifications"
table. Our company shall not be liable
EN
for any damages that will arise when the
product is used without grounding in
accordance with the local regulations.
• Connection must comply with national
regulations.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or
breaker protection are specified in
the “Technical specifications” section.
If the current value of the fuse or
breaker in the house is less than 13
Amps, have a qualified electrician
install a 13 Amp fuse.
• The specified voltage must be equal
to your mains voltage.
• Do not make connections via
extension cables or multi-plugs.
Damaged power cables must be
B
replaced by the Authorized Service
Agents.
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket in a
readily accessible position.
Should the mains lead of the appliance
become damaged or need replacing at
any time, it must be replaced by a special
purpose made mains lead which can only
be obtained from a Authorised Service
Agent.
fuse cover has been fitted. Colour of the
replacement fuse cover must be the same
colour as that visible on the pin face of the
plug. Fuse covers are available from any
good electrical store.
Important
Fitting a different plug
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying
the terminals on your plug, proceed as
follows:
1 Connect the green - yellow or green
(earth) wire to the terminal in the plug
marked ‘E’ or with the symbol f or
coloured green and yellow or green.
2 Connect the blue (neutral) wire to the
terminal in the plug marked ‘N’ or
coloured black.
3 Connect the brown (live) wire to the
terminal in the plug marked ‘L’ or
coloured red.
With the alternative plugs a 13A fuse must
be fitted either in the plug or adaptor or in the
main fuse box. If in doubt contact a qualified
electrician.
This appliance must be earthed
B
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as
a plug with a bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse
need to be replaced an ASTA approved
BS1362 fuse of the same rating must be
used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the
plug must not be used until a replacement
11
EN
First use
Before starting to use the product, make
sure that all preparations are made in
accordance with the instructions in
sections "Important safety instructions"
and "Installation".
To prepare the product for washing
laundry, perform first operation in Drum
Cleaning programme. If your machine
is not featured with Drum Cleaning
programme, use Cottons-90 programme
and select Additional Water or Extra Rinse
auxiliary functions as well. Before starting
the programme, put max. 100 g of
powder anti-limescale into the main wash
detergent compartment (compartment nr.
II). If the anti-limescale is in tablet form,
put only one tablet into compartment nr.
II. Dry the inside of the bellow with a clean
piece of cloth after the programme has
come to an end.
2. Remove water drain and water supply
connections.
3. Drain the remaining water in the
product completely; see, "Draining
remaining water and cleaning the
pump filter".
4. Install transportation safety bolts
in the reverse order of removal
procedure; see, "Removing the
transportation locks".
Never move the product without the
C
transportation safety bolts properly
fixed in place!
Disposing of the old product
Dispose of the old product in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how
to dispose of your product.
For children's safety, cut the power
cable and break the locking mechanism
of the loading door so that it will be
nonfunctional before disposing of the
product.
Use an anti-limescale suitable for the
C
washing machines.
Some water might have remained in
C
the product due to the quality control
processes in the production. It is not
harmful for the product.
Disposing of packaging material
Packaging materials are dangerous to
children. Keep packaging materials in
a safe place away from reach of the
children.
Packaging materials of the product are
manufactured from recyclable materials.
Dispose of them properly and sort
in accordance with recycled waste
instructions. Do not dispose of them with
normal domestic waste.
Transportation of the product
1. Unplug the product before
transporting it.
12
EN
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.