This section provides the safety
instructions necessary to prevent
the risk of injury and material
damage. Failure to observe these
instructions will invalidate all
types of product warranty.
1.1. General safety
• This product should not be
used by persons with physical,
sensory and mental disabilities,
without sufficient knowledge
and experience or by children.
The device can only be
used by such persons under
supervision and instruction of
a person responsible for their
safety. Children should not be
allowed to play with this device.
• In case of malfunction, unplug
the device.
• After unplugging, wait at least
5 minutes before plugging
in again. Unplug the product
when not in use. Do not touch
the plug with wet hands! Do
not pull the cable to plug off,
always hold the plug.
• Wipe the power plug’s tip with
a dry cloth before plugging in.
• Do not plug in the refrigerator if
the socket is loose.
• Unplug the product during
installation, maintenance,
cleaning and repair.
• If the product will not be used
for a while, unplug the product
and remove any food inside.
• Do not use steam or steamed
cleaning materials for cleaning
the refrigerator and melting the
ice inside. Steam may contact
the electrified areas and cause
short circuit or electric shock!
• Do not wash the product by
spraying or pouring water on it!
Danger of electric shock!
• In case of malfunction, do not
use the product, as it may
cause electric shock. Contact
the authorized service before
doing anything.
• Plug the product into an
earthed socket. Earthing
must be done by a qualified
electrician.
• If the product has LED type
lighting, contact the authorized
service for replacing or in case
of any problem.
• Do not touch frozen food with
wet hands! It may adhere to
your hands!
• Do not place liquids in bottles
and cans into the freezer
compartment. They may burst
out!
• Place liquids in upright position
after tightly closing the lid.
Refrigerator / User Guide
3 / 34 EN
Safety and environment instructions
• Do not spray flammable
substances near the product,
as it may burn or explode.
• Do not keep flammable
materials and products with
flammable gas (sprays, etc.) in
the refrigerator.
• Do not place containers
holding liquids on top of the
product. Splashing water on
an electrified part may cause
electric shock and risk of fire.
• Exposing the product to rain,
snow, sunlight and wind will
cause electrical danger. When
relocating the product, do not
pull by holding the door handle.
The handle may come off.
• Take care to avoid trapping any
1.1.1 HC warning
If the product comprises a cooling
system using R600a gas, take
care to avoid damaging the
cooling system and its pipe while
using and moving the product.
This gas is flammable. If the
cooling system is damaged, keep
the product away from sources
of fire and ventilate the room
immediately.
part of your hands or body in
any of the moving parts inside
C
the product.
• Do not step or lean on the door,
drawers and similar parts of
the refrigerator. This will cause
the product to fall down and
cause damage to the parts.
• Take care not to trap the power
cable.
1.1.2 For models with
water fountain
• In order to operate the water
circuit of the refrigerator
smoothly, the water mains
pressure must be between
1-8 bars. For conditions where
water mains pressure exceeds
5 bars a pressure regulator
should be used. If the water
mains pressure exceeds 8
bars then the refrigerator’s
water circuit should not be
The label on the inner left
side indicates the type of
gas used in the product.
4 / 34 EN
Refrigerator / User Guide
Safety and environment instructions
connected to the water mains.
If you lack the knowledge of
how to measure the water
mains pressure, please seek
a professional support.Use
1.4. Compliance with WEEE Directive
and Disposing of the Waste Product
This product complies with EU WEEE
Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and
electronic equipment (WEEE).
drinking water only.
1.2. Intended use
• This product is designed for
home use. It is not intended for
commercial use.
• The product should be used to
store food and beverages only.
• Do not keep sensitive
products requiring controlled
temperatures (vaccines,
heat sensitive medication,
medical supplies, etc.) in the
refrigerator.
• The manufacturer assumes no
responsibility for any damage
due to misuse or mishandling.
• The product’s bench life is
10 years. The spare parts
center for the recycling of electrical and
electronic equipment. Please consult your local
authorities to learn about these collection
centers.
1.5. Compliance with RoHS Directive
• This product complies with EU WEEE Directive
(2011/65/EU). It does not contain harmful and
prohibited materials specified in the Directive.
1.6. Package information
• Packaging materials of the product are
manufactured from recyclable materials in
accordance with our National Environment
Regulations. Do not dispose of the packaging
materials together with the domestic or other
wastes. Take them to the packaging material
collection points designated by the local
authorities.
necessary for the product to
function will be available for
this period.
This product has been manufactured
with high quality parts and materials
which can be reused and are suitable
for recycling. Do not dispose of the
waste product with normal domestic
and other wastes at the end of its
service life. Take it to the collection
1.3. Child safety
• Keep packaging materials out
of children’s reach.
• Do not allow the children to
play with the product.
• If the product’s door comprises
a lock, keep the key out of
children’s reach.
Refrigerator / User Guide
5 / 34 EN
2 Refrigerator
2
3
*4
5
*6
1
*7
*11
*16
*17
*18
12
13
14
15
13
*8
10
*9
1- Freezer compartment
2- Cooler compartment
3- Fan
4- Butter-cheese compartment
5- Glass shelves
6- Cooler compartment door shelves
7- Minibar accessory
8- Water tank
9- Bottle shelf
*Optional: Figures in this user guide are schematic and may not be exactly match your product. If your
product does not comprise the relevant parts, the information pertains to other models.
6 / 34 EN
Refrigerator / User Guide
3 Installation
3.1. Right place for installation
Contact the Authorized Service for the product's
installation. To ready the product for installation,
see the information in the user guide and make
sure the electric and water utilities are as required.
If not, call an electrician and plumber to arrange
the utilities as necessary.
WARNING: The manufacturer assumes
no responsibility for any damage caused
B
B
A
•SPlacetheproductonaflatsurfacetoavoid
vibration.
•Placetheproductatleast30cmawayfromthe
heater, stove and similar sources of heat and at
least 5 cm away from electric ovens.
function efficiently. If the product will be placed
in an alcove, remember to leave at least 5 cm
distance between the product and the ceiling
and the walls.
must be unplugged during installation.
Failure to do so may result in death or
serious injuries!
WARNING: : If the door span is too
narrow for the product to pass, remove
the door and turn the product sideways; if
this does not work, contact the authorized
service.
3.2. Attaching the plastic wedges
Use the plastic wedges in the provided with
the product to provide sufficient space for air
circulation between the product and the wall.
1.
To attach the wedges, remove the screws on the
product and use the screws provided with the wedges.
2.
Attach 2 plastic wedges on the ventilation cover
shown as j in the figure.
Refrigerator / User Guide
7 / 34 EN
Installation
3.3. Adjusting the stands
If the product is not in balanced position, adjust the
front adjustable stands by rotating right or left.
3.4. Power connection
WARNING: Do not use extension or multi
A
B
C
• Our firm will not assume responsibility for any
• The power cable plug must be easily
• Connect the refrigerator to an earthed socket
• Do not use multi-group plug with or without
sockets in power connection.
WARNING: Damaged power cable must
be replaced by Authorized Service.
When placing two coolers in adjacent
position, leave at least 4 cm distance
between the two units.
damages due to usage without earthing and
power connection in compliance with national
regulations.
accessible after installation.
with 220-240V/50 Hz voltage. The plug must
comprise a 10-16A fuse.
extension cable between the wall socket and
the refrigerator.
3.5. Water connection
(Optional)
WARNING: Unplug the product and
the water pump (if available) during
A
The product’s water mains, filter and carboy
connections must be rendered by authorizer
service. The product can be connected to a carboy
or directly to the water mains, depending on the
model. To establish the connection, the water hose
must first be connected to the product.
Check to see the following parts are supplied with
your product’s model:
1
3
1. Connector (1 piece): Used to attach the water
2. Hose clip (3 pieces): Used to fix the water
3. Water hose (1 piece, 5 meter diameter 1/4
4. Faucet adapter (1 piece): Comprises a porous
5. Water filter (1 piece *Optional): Used to
connection.
2
4
hose to the rear of the product.
hose on the wall.
inches): Used for the water connection.
filter, used for connection to the cold water
mains.
connect the mains water to the product. Water
filter is not required if carboy connection is
available.
*5
8 / 34 EN
Refrigerator / User Guide
Installation
3.6. Connecting water
hose to the product
To connect the water hose to the product,
follow the instructions below.
1. Remove the connector on the hose nozzle
adaptor in the back of the product and run the
hose through the connector.
3.7. Connecting to water mains
(Optional)
To use the product by connecting to the cold water
mains, a standard 1/2” valve connector must be
installed to the cold water mains in your home. If
the connector is not available or if you are unsure,
consult a qualified plumber.
1. Detach the connector (1) from the faucet
adaptor (2).
2. Push the water hose down tightly and connect
to the hose nozzle adaptor.
3. Tighten the connector manually to fix on the
hose nozzle adaptor. You may also tighten the
connector using a pipe wrench or pliers.
3
2. Connect the faucet adaptor to the water mains
valve.
3. Attach the connector around the water hose.
2
23
1
1
4. Connect the other end of the hose to the
water mains (See Section 3.7) or, to use
carboy, to the water pump (See Section 3.8).
Refrigerator / User Guide
9 / 34 EN
Installation
4. Attach the connector into the faucet adaptor
and tighten by hand / tool.
5. To avoid damaging, shifting or accidentally
disconnecting the hose, use the clips provided
to fix the water hose appropriately.
2. Connect the other end of the water hose to
the water pump by pushing the hose into the
pump’s hose inlet.
3. Place and fasten the pump hose inside the
carboy.
WARNING: After turning the faucet
on, make sure there is no water leak on
A
either end of the water hose. In case of
leakage, turn the valve off and tighten
all connections using a pipe wrench or
pliers.
3.8. For products using water carboy
(Optional)
To use a carboy for the product’s water
connection, the water pump recommended by the
authorized service must be used.
1. Connect one end of the water hose provided
with the pump to the product (see 3.6) and
follow the instructions below.
4. Once the connection is established, plug in
and start the water pump.
Please wait 2-3 minutes after starting
the pump to achieve the desired
C
C
C
efficiency.
See also the pump’s user guide for
water connection.
When using carboy, water filter is not
required.
3.9 Water filter
(Optional)
The product may have internal or external filter,
depending on the model. To attach the water filter,
follow the instructions below.
10 / 34 EN
Refrigerator / User Guide
Installation
3.9.1.Fixing external filter
on the wall (Optional)
WARNING: Do not fix the filter on the
A
Check to see the following parts are supplied with
your product’s model:
product.
5
4
6
4. Attach the water hose extending from the top
of the filter to the product’s water connection
adaptor, (see 3.6.)
1
1. Connector (1 piece): Used to attach the water
hose to the rear of the product.
2. Faucet adapter (1 piece): Used for connection
to the cold water mains.
3. Porous filter (1 piece)
4. Hose clip (3 pieces): Used to fix the water
hose on the wall.
5. Filter connecting apparatus (2 pieces): Used to
fix the filter on the wall.
6. Water filter (1 piece): Used to connect the
product to the water mains. Water filter is not
necessary when using carboy connection.
1. Connect the faucet adaptor to the water mains
valve.
2. Determine the location to fix the external filter.
Fix the filter’s connecting apparatus (5) on the
wall.
3. Attach the filter in upright position on the filter
connecting apparatus, as indicated on the
label. (6)
3
2
After the connection is established, it should look
like the figure below.
Refrigerator / User Guide
11 / 34 EN
Installation
3.9.2.Internal filter
The internal filter provided with the product is not
installed upon delivery; please follow the instructions
below to install the filter.
Water line:
1. “Ice Off” indicator must be active while
installing the filter. Switch the ON-OFF
indicator using the “Ice” button on the screen.
2. Remove the vegetable bin (a) to access the
water filter.
Carboy line:
C
Do not use the first 10 glasses of
water after connecting the filter.
12 / 34 EN
a
Refrigerator / User Guide
Installation
3. Remove the water filter by-pass cover by
pulling.
A few drops of water may flow out
after removing the cover; this is
C
4. Place the water filter cover into the
mechanism and push to lock in place.
normal.
5. Push the “Ice” button on the screen again to
cancel the “Ice Off” mode.
The water filter will clear certain foreign
particles in the water. It will not clear the
C
C
Refrigerator / User Guide
microorganisms in the water.
See section 5.2 for activating the filter
replacing period.
13 / 34 EN
4 Preparation
4.1. What to do for energy saving
mehmet
Connecting the product to electronic
energy-saving systems is harmful, as it
A
• Do not keep the refrigerator doors open for
• Do not place hot food or beverages into the
• Do not overfill the refrigerator; blocking the
• The energy consumption value specified for
• Depending on the product’s features;
• The baskets/drawers that are provided with the
• Food contact with the temperature sensor in
• Make sure the foods are not in contact with
may damage the product.
long periods.
refrigerator.
internal air flow will reduce cooling capacity.
the refrigerator was measured with the freezer
compartment’s upper shelf removed, other
shelves and the lowest drawers in place and
under maximum load. The top glass shelf can
be used, depending on the shape and size of
food to be frozen.
defrosting frozen foods in the cooler
compartment will ensure energy saving and
preserve food quality.
chill compartment must always be in use for
low energy consumption and for better storage
conditions.
the freezer compartment may increase energy
consumption of the appliance. Thus any
contact with the sensor(s) must be avoided.
the cooler compartment temperature sensor
described below.
4.2. First Use
Before using your refrigerator, make sure the
necessary preparations are made in line with
the instructions in “Safety and environment
instructions” and “Installation” sections.
• Keep the product running with no food
inside for 6 and do not open the door, unless
absolutely necessary.
A sound will be heard when the
compressor is engaged. It is normal to
C
C
C
hear sound even when the compressor is
inactive, due to the compressed liquids
and gasses in the cooling system.
It is normal for the front edges of the
refrigerator to be warm. These areas are
designed to warm up in order to prevent
condensation.
In some models, the instrument panel
automatically turns off 5 minutes after
the door has closed. It will be reactivated
when the door has opened or pressed on
any key.
14 / 34 EN
Refrigerator / User Guide
5 Using the product
5.1. Indicator panel
Indicator panels may vary depending on the model of your product.
Audial and visual functions of the indicator panel will assist in using the refrigerator.
1
8
2
3
9
76
1.
Cooler compartment indicator
2.
Error status indicator
3.
Temperature indicator
4.
Vacation function button
5.
Temperature adjustment button
6.
Compartment selection button
7.
Cooler compartment indicator
8.
Economy mode indicator
9.
Vacation function indicator
*optional
45
*Optional: The figures in this user guide are intended as drafts and may not perfectly match your
product. If your product does not comprise the relevant parts, the information pertains to other models.
C
Refrigerator / User Guide
15 / 34 EN
Using the product
1. Cooler compartment indicator
The cooler compartment light will turn on when
adjusting the cooler compartment temperature.
2. Error status indicator
This sensor will activate if the refrigerator is not
cooling adequately or in case of sensor fault. When
this indicator is active, the freezer compartment
temperature indicator will display "E" and the
cooler compartment temperature indicator will
display "1, 2, 3..." etc. numbers. The numbers on
the indicator serve to inform the service personnel
about the fault.
3. Temperature indicator
Indicates the temperature of the freezer and cooler
compartments.
4.Vacation function button
To activate this function, press and hold the
Vacation button for 3 seconds. When the Vacation
function is active, the cooler compartment
temperature indicator displays the inscription
"- -" and no cooling process will be active in
the cooling compartment. This function is not
suitable to keep food in the cooler compartment.
Other compartments will remain cooled with the
respective temperature set for each compartment.
Push the Vacation button (
) again to cancel
this function.
5. Temperature adjustment button
Respective compartment's temperature varies in
-24°C..... -18°C and 8°C...1°C ranges.
6. Compartment selection button
Use the refrigerator compartment selection
button to toggle between the cooler and freezer
compartments.
7. Cooler compartment indicator
The freezer compartment light will turn on when
adjusting the cooler compartment temperature.
8. Economy mode indicator
Indicates the refrigerator is running on energysaving mode. This indicator will be active when
the temperature in the freezer compartment is set
to -18°C.
9.Vacation function indicator
Indicates the vacation function is active.
16 / 34 EN
Refrigerator / User Guide
Using the product
10
1
1- Economic use
2- High temperature / fault alert
3- Rapid cooling
4- Vacation function
5- Cooler compartment temperature setting
6- Energy saving (display off)
7- Keypad lock
8- Eco-fuzzy
9- Freezer compartment temperature setting
10- Rapid freezing
2
3
456789
*Optional: The figures in this user guide are intended as drafts and may not perfectly match
your product. If your product does not comprise the relevant parts, the information pertains
C
Refrigerator / User Guide
to other models.
17 / 34 EN
Using the product
1. Economic use
This sign will light up when the freezer
compartment is set to -18°C', the most
economical setting. () Economic use indicator
will turn off when rapid cooling or rapid freezing
function is selected.
2. High temperature / fault alert
This indicator (
) will light up in case of
temperature faults or fault alerts. If you see this
indicator is lit up, please see the "recommended
solutions for problems" section in this guide.
3. Rapid cooling
When the rapid cooling function is turned on, the rapid cool indicator will light up (
partment temperature indicator will display the value 1.
Push the Rapid cool button again to cancel this function. The Rapid cool indicator will turn off and return to
normal setting. The rapid cooling function will be automatically cancelled after 1 hour, unless cancelled by
the user. Too cool a large amount of fresh food, press
the rapid cool button before placing the food in the cooler compartment.
) and the cooler com-
4. Vacation function
To activate the Vacation function, press the button
number (4) for (
the vacation mode indicator (
) 3 seconds; this will activate
). When the
Vacation function is active, the cooler compartment
temperature indicator displays the inscription
"- -" and no cooling process will be active in
the cooling compartment. This function is not
suitable to keep food in the cooler compartment.
Other compartments will remain cooled with the
respective temperature set for each compartment.
Push the vacation function button again to cancel
this function.
5. Cooler compartment temperature setting
After pressing the button number (5), the
cooler compartment temperature can be set to
8,7,6,5,4,3,2 and 1 respectively.(
)
6. Energy saving (display off)
Pressing this button () will light up the energysaving sign () and the Energy-saving function
will activate. Activating the energy-saving function
will turn off all other signs on the display. When
the energy-saving function is active, pressing any
button or opening the door will deactivate the
energy-saving function and the display signals will
return to normal. Pressing this button () again
will turn off the energy-saving sign and deactivate
the energy-saving function.
7. Keypad lock
Press the keypad lock button (
) simultaneously
for 3 seconds. The keypad lock sign ( ) will light
up and the keypad lock will be activated; the
buttons will be inactive when the Keypad lock is
activated. Press the Keypad lock button again
simultaneously for 3 seconds. The keypad lock
sign will turn off and the keypad lock mode will be
disengaged. Press the keypad lock button () to
prevent changing the refrigerator's temperature
settings.
8. Eco-fuzzy
To activate the eco-fuzzy function, press and hold
the eco-fuzzy button for 1 second. When this
function is active, the freezer will switch to the
economic mode after at least 6 hours and the
economic use indicator will light up. To deactivate
) eco-fuzzy function, press and hold the
the (
eco-fuzzy function button for 3 seconds.
The indicator will light up after 6 hours when the
eco-fuzzy function is active.
9. Freezer compartment temperature setting
The temperature in the freezer compartment is
adjustable. Pressing the button number (9) will
enable the freezer compartment temperature to be
set at -18,-19, -20, -21, -22, -23 and -24.
18 / 34 EN
Refrigerator / User Guide
Using the product
10. Rapid freezing
For rapid freezing, press the button number (10);
this will activate the rapid freezing indicator ().
When the rapid freezing function is turned on, the
rapid freeze indicator will light up and the freezer
compartment temperature indicator will display
the value -27. Press the Rapid freeze button (
) again to cancel this function. The Rapid freeze
indicator will turn off and return to normal setting.
The rapid freezing function will be automatically
cancelled after 24 hours, unless cancelled by the
user. To freeze a large amount of fresh food, press
the rapid freeze button before placing the food in
the freezer compartment.
*Optional: The figures in this user guide are intended as drafts and may not perfectly match
your product. If your product does not comprise the relevant parts, the information pertains
to other models.
20 / 34 EN
Refrigerator / User Guide
Using the product
1. Freezer compartment temperature setting
Pressing the button (
the freezer compartment temperature to be set at
-18,-19,-20,-21 ,-22,-23,-24,-18...
2. Economy mode
Indicates the refrigerator is running on energysaving mode. This indicator will be active when the
freezer compartment temperature is set at -18 or
the energy-saving cooling is engaged by eco-extra
function. (
)
3. Error status
This sensor will activate if the refrigerator is not
cooling adequately or in case of sensor fault. (
When this indicator is activated, the freezer
compartment temperature indicator will display "E"
and the cooler compartment temperature indicator
will display "1, 2, 3..." etc. numbers. The numbers
on the indicator serve to inform the service
personnel about the fault.
4. Cooler compartment temperature setting
After pressing the button (
cooler compartment temperature can be set to
8,7,6,5,4,3,2.. respectively.
5. Rapid cooling
For rapid cooling , press the button number (5);
this will activate the rapid cooling indicator (
Press this button again to deactivate this function.
Use this function when placing fresh foods into
the cooler compartment or to rapidly cool the
food items. When this function is activated, the
refrigerator will be engaged for 1 hour.
6. Vacation function
When the Vacation function (
cooler compartment temperature indicator displays
the inscription "- -" and no cooling process
will be active in the cooling compartment. This
function is not suitable to keep food in the cooler
compartment. Other compartments will remain
cooled with the respective temperature set for
each compartment.
) number (1) will enable
) number (4), the
).
) is active, the
Press the vacation function button again to cancel
this function. (
)
7. Keypad lock / Keypad lock / filter replacing
alert cancellation
Press keypad lock button ( ) to activate the
keypad lock. You may also use this function to
prevent changing the refrigerator's temperature
settings. The refrigerator's filter must be replaced
every 6 months. If you follow the instructions in
the section 5.2, the refrigerator will automatically
calculate the remaining period and the filter
replacing alert indicator (
filter expires.
)
Press and hold the button (
) will light up when
) for 3 seconds to
turn off the filter alert light.
8. Water, fragmented ice, ice cubes selection
Navigate the water (
), ice cube () and
fragmented ice () selections using the button
number 8. The active indicator will remain lit.
9. Ice making on/off
Press the button (
) number (9) to cancel (
) or activate () ice-making.
10. Display on/off
Press the button () number (10) to
cancel (XX) or activate () display on/
off.
11. Autoeco
Press the auto eco button (
), number (11),
for 3 seconds to activate this function. If the
door remains closed for a long time when this
function is activated, the cooler section will switch
to economic mode. Press the button again to
deactivate this function.
The indicator will light up after 6 hours when the
auto eco function is active. (
)
12. Rapid freezing
Press the button (
) number (12) for rapid
freezing. Press the button again to deactivate the
function.
Refrigerator / User Guide
21 / 34 EN
Using the product
A
5.2. Activating water filter
change warning
(For products connected to the mains water
line and equipped with filter)
Water filter change warning is activated as follows:
1. Within 60 seconds after switching on the
refrigerator, press and hold the Display and
Vacation buttons for 3 seconds.
2. Then enter 1-4-5-3 as password.
Confirming the entered Selecting the
password password numbers
4
3
A
2
Enter 1-4-5-3 as follows:
Press FF set button for once.
Press FRZ set button for once.
Press FF set button for 4 times.
Press FRZ set button for once.
Press FF set button for 5 times.
Press FRZ set button for once.
Press FF set button for 3 times.
Press FRZ set button for once.
If the password is entered correctly, buzzer will sound
shortly and Filter Change Warning indicator will turn on.
Automatic filter usage time calculation is not enabled
ex factory.
It must be enabled in products equipped with a filter.
The refrigerator will give filter change warning with
6-month intervals automatically.
If the same procedure is repeated when the automatic
filter usage time calculation is enabled, then the
function will be canceled.
1
22 / 34 EN
Refrigerator / User Guide
Using the product
5.3. Using the water fountain
(for certain models)
The first few glasses of water taken from
C
C
You must wait approximately 12 hours to get cold
water after first operating.
Use the display to select the water option, then pull
the trigger to get water. Remove the glass shortly
after pulling the trigger.
the fountain will normally be warm.
If the water fountain is not used for a long
time, dispose of the first few glasses of
water to get clean water.
5.4. Filling the fountain water tank
Open the water tank’s lid, as shown in the figure.
Fill in pure and clean drinking water. Close the lid.
Refrigerator / User Guide
23 / 34 EN
Using the product
5.5. Cleaning the water tank
Remove the water filling reservoir inside the door
shelf.
Detach by holding both sides of the door
shelf.
Hold both sides of the water tank and remove at
45° angle.
Remove and clean the water tank lid.
Do not fill the water tank with fruit juice,
fizzy beverages, alcoholic beverages or
any other liquids incompatible for use in
the water fountain. Using such liquids
will cause malfunction and irreparable
damage in the water fountain. Using
A
A
the fountain in this way is not within the
scope of warranty. Such certain chemicals
and additives in the beverages / liquids
may cause material damage to the water
tank.
The water tank and water fountain
components cannot be washed with
dishwashers.
24 / 34 EN
Refrigerator / User Guide
Using the product
5.6. Taking ice / water
(Optional)
To take water ( ) / ice cube ( ) / fragmented
ice ( ), use the display to select the respective
option. Take water/ice by pushing the trigger
on the water fountain forward. When switching
between ice cube ( ) / fragmented ice ( )
options, the previous ice type may be discharged a
few more times.
• You must wait approximately 12 hours before
taking ice from the ice / water fountain for the
first time. The fountain may not discharge ice if
there is insufficient ice in the ice box.
• The 30 pieces of ice cubes (3-4 Litres) taken
after first operating should not be used.
• In case of power blackout or temporary
malfunction, the ice may partly melt and refreeze. This will cause the ice pieces to merge
with each other. In case of extended power
blackouts or malfunction, the ice may melt
and leak out. If you experience this problem,
remove the ice in the ice box and clean the
box.
WARNING: The product’s water system
A
should be connected to cold water line
only. Do not connect to hot water line.
• The water may be cloudy during first use of
the filter; do not consume the first 10 glasses
of water.
• You must wait approximately 12 hours to get
cold water after first installation.
• The product’s water system is designed
for clean water only. Do not use any other
beverages.
• It is recommended to disconnect the water
supply if the product will not be used for long
periods during vacation etc.
• If the water fountain is not used for a long
time, the first 1-2 glasses of water received
may be warm.
5.7. Drip tray
(optional)
The water dripping from the water fountain
accumulates on the drip tray; no water drainage is
available. Pull the drip tray out or push on the edges
to remove the tray. You may then discharge the water
inside the drip tray.
• The product may not discharge water during
first operation. This is caused by the air in
the system. The air in the system must be
discharged. To do this, push the water fountain
trigger for 1-2 minutes until the fountain
discharges water. The initial water flow may be
irregular. The water will flow normally once the
air in the system is discharged.
Refrigerator / User Guide
25 / 34 EN
Using the product
5.8. Zero degree compartment
(Optional)
Use this compartment to keep delicatessen
at lower temperatures or meat products for
immediate consumption. Do not place fruits and
vegetables in this compartment. You can expand
the product's internal volume by removing any
of the zero degree compartments. To remove the
compartment, simply pull forth, lift up and pull out.
5.9. Vegetable bin
The refrigerator's vegetable bin is designed to
keep vegetables fresh by preserving humidity.
For this purpose, the overall cold air circulation is
intensified in the vegetable bin. Keep fruits and
vegetables in this compartment. Keep the greenleaved vegetables and fruits separately to prolong
their life.
5.10. Blue light
(Optional)
The product's vegetable bins comprise blue
light. The vegetables in the bin will continue
photosynthesize under the blue light's wavelength
effect and remain live and fresh.
5.11. Ionizer
(Optional)
The ionizer system in the cooler compartment's
air duct serves to ionize the air. The negative
ion emissions will eliminate bacteria and other
molecules causing odour in the air.
5.12. Minibar
(Optional)
The refrigerator's minibar door shelf can be
accessed without opening the door. This will
allow you to easily take frequently consumed
food and beverages from the refrigerator. To open
the minibar cover, push with your hand and pull
towards yourself.
WARNING: Do not sit, hang or place
heavy objects on the minibar cover. This
A
To close this compartment, simply push forward
from the upper section of the cover.
may damage the product or cause you to
be injured.
5.13. Odour filter
(optional)
The odour filter in the cooler compartment's air
duct will prevent undesirable odour formation.
26 / 34 EN
Refrigerator / User Guide
Using the product
5.14. Icematic and ice storage box
(Optional)
Fill the icematic with water and put in place.
The ice will be ready after approximately two
hours. Do not remove the icematic to take the
ice.
Turn the buttons on the ice chambers righthand side by 90°; the ice will fall to the ice storage box below. You may then remove the ice
storage box and serve the ice.
The ice storage box is intended for
storing ice only. Do not fill with water.
C
Doing so will cause it to break.
5.15. Ice-maker
(Optional)
Ice maker is located on the upper section of the
freezer cover.
Hold the handles on the sides of the ice stock
reservoir and move up to remove.
Remove the ice-maker decorative lid by moving
up.
OPERATION
To remove the ice reservoir
Hold the ice stock reservoir from the handles, then
move up and pull the ice stock reservoir. (Figure 1)
To reinstall the ice reservoir
Hold the ice stock reservoir from the handles, move up
with an angle to fit the sides of the reservoir to their
slot and make sure that the ice selector pin is mounted
properly. (Figure 2)
Refrigerator / User Guide
Push downwards firmly, until there is no space left
between the reservoir and the door plastic. (Figure 2)
If you have difficulty in refitting the reservoir, turn the
rotary gear 90° and reinstall it as shown in the figure3.
Any sound you hear when the ice drops into the
reservoir is a part of normal operation.
27 / 34 EN
Using the product
When the ice dispenser does not work
properly
If you do not remove ice cubes for a long time, they
will cause formation of ice chunks. In this case, please
remove the ice stock reservoir in accordance with the
instructions given above, seperate the ice chunks,
discard the inseparable ice and put the ice cubes back
into the ice stock reservoir. (Figure 4)
Caution!
Do not insert the hand or any other object into the ice
canal and blade since it may damage the parts or hurt
the hand.
Do not let the children hang on the ice dispenser or the
ice maker since it may cause an injury
To prevent dropping the ice stock reservoir use both
hands when removing it.
If you close the door hard, it may cause water spilling
over the ice stock reservoir.
Do not dismount the ice stock reservoir unless it is
necessary.
When ice does not come out, check for any ice stuck
in the canal and remove it. Regularly check the ice
canal to clear the obstacles as shown in the figure 5.
When using your refrigerator for the first time or when
not using it for an extended period of time Ice cubes
may be small due to air in the pipe after connection,
any air will be purged during normal use.
Discard the ice produced for approximately one day
since the water pipe may contain the contaminants.
28 / 34 EN
Refrigerator / User Guide
Using the product
5.16. Freezing fresh food
• To preserve food quality, the food items placed
in the freezer compartment must be frozen as
quickly as possible, use the rapid freezing for
this.
• Freezing the food items when fresh will extend
the storage time in the freezer compartment.
• Pack the food items in air-tight packs and seal
tightly.
• Make sure the food items are packed before
putting in the freezer. Use freezer holders,
tinfoil and damp-proof paper, plastic bag
or similar packaging materials instead of
traditional packaging paper.
• Mark each food pack by writing the date on the
package before freezing. This will allow you to
determine the freshness of each pack every
time the freezer is opened. Keep the earlier
food items in the front to ensure they are used
first.
• Frozen food items must be used immediately
after defrosting and should not be frozen again.
• Do not free large quantities of food at once.
5.17. Recommendations for
storing frozen foods
The compartment must be set to at least -18°C.
1. Place the food items in the freezer as quickly
as possible to avoid defrosting.
2. Before freezing, check the “Expiry Date” on
the package to make sure it is not expired.
3. Make sure the food’s packaging is not
damaged.
5.18. Deep freezer details
As per the IEC 62552 standards, the freezer must
have the capacity to freeze 4,5 kg of food items at
-18°C or lower temperatures in 24 hours for each
100 litres of freezer compartment volume. Food
items can only be preserved for extended periods
at or below temperature of -18°C . You can keep
the foods fresh for months (in deep freezer at or
below temperatures of 18°C ).
The food items to be frozen must not contact
the already-frozen food inside to avoid partial
defrosting.
Boil the vegetables and filter the water to extend
the frozen storage time. Place the food in air-tight
packages after filtering and place in the freezer.
Bananas, tomatoes, lettuce, celery, boiled eggs,
potatoes and similar food items should not be
frozen. Freezing these food items will simply
reduce the nutritional value and food quality,
as well as possible spoiling which is harmful to
health.
Freezer
Compartment
Setting
-18°C4°CThis is the default, recommended setting.
-20,-22 veya
-24°C
Rapid Freeze4°C
-18°C or colder2°C
Refrigerator / User Guide
Cooler
Compartment
Setting
4°C
Descriptions
These settings are recommended for ambient temperatures
exceeding 30°C.
Use this to freeze food items in a short time, the product will reset to
previous settings when the process is completed.
Use these settings if you believe the cooler compartment is not cold
enough due to ambient temperature or frequently opening the door.
29 / 34 EN
Loading...
+ 145 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.