Beko GNE 114610 X User Manual

0 (0)

Refrigerator

GNE 114610 X

Please read this manual first!

Dear Customer,

We hope that your product, which has been produced in modern plants and checked under the most meticulous quality control procedures, will provide you an effective service.

For this, we recommend you to carefully read the entire manual of your product before using it and keep it at hand for future references.

This manual

Will help you use your appliance in a fast and safe way.

Read the manual before installing and operating your product.

Follow the instructions, especially those for safety.

Keep the manual in an easily accessible place as you may need it later.

Besides, read also the other documents provided with your product.

Please note that this manual may be valid for other models as well.

Symbols and their descriptions

This instruction manual contains the following symbols:

C Important information or useful usage tips.

AWarning against dangerous conditions for life and property.

BWarning against electric voltage.

This product bears the selective sorting symbol for waste electrical and Recycling electronic equipment (WEEE).

This means that this product must be handled pursuant to European Directive 2002/96/EC in order to be recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional authorities.

Electronic products not included in the selective sorting process are potentially dangerous for the environment and human heatlh due to the presence of hazardous substances.

CONTENTS

 

1 Your refrigerator

3

Technical specifications of your refrigerator..................................................

4

2 Warnings

5

General safety..............................................................................................

5

Starting Up...................................................................................................

6

Intended use................................................................................................

6

Safety instructions........................................................................................

6

Things to be done for energy saving.............................................................

6

3 Installation

7

Preparation..................................................................................................

7

Points to be considered when re-transporting your refrigerator....................

7

Before operating your refrigerator.................................................................

8

Electric connection.......................................................................................

8

Disposing of the packaging..........................................................................

8

Disposing of your old refrigerator..................................................................

8

Placing and Installation.................................................................................

9

Floor balance adjustment.............................................................................

9

Adjusting the gap between the upper door.................................................

10

4 Using your refrigerator

11

Indicator Panel...........................................................................................

11

Door Open Alarm: .....................................................................................

13

Egg tray.....................................................................................................

14

Sliding Body Shelves..................................................................................

14

Crisper ......................................................................................................

14

Chiller compartment...................................................................................

14

Rotating Middle Section ............................................................................

15

Multi Zone Storage Compartment..............................................................

15

Blue light....................................................................................................

15

5 Maintenance and cleaning

16

Protection of plastic surfaces ....................................................................

16

6 Recommended solutions for the problems

17

2 EN

Beko GNE 114610 X User Manual

1 Your refrigerator

A

12

3 13 2

1

4 5

6 7 14

8

 

9

15

10

11

16

 

B

 

C

A-

Fridge compartment

 

 

B-

Freezer compartment

 

 

C-

Multi Zone

 

 

1-

Fridge compartment door shelves

8-

Bottle shelf

2-

Fridge compartment adjustable

9-

Icematic

cabinet shelves

10-

Icebox

3-

Diffuser cover

11Frozen food storage compartments

4-

Illumination lens

12Butter & Cheese shelf cover

5-

Rotating middle section

13Butter & Cheese shelf

6-

Chiller compartment

14-

Bottle holder

7-

Crisper

15Multi Zone compartment shelves

 

 

16Multi Zone compartment

CFigures that take place in this instruction manual are schematic and may not correspond exactly with your product. If the subject parts are not included in the product you have purchased, then it is valid for other models.

3 EN

Technical specifications of your refrigerator

Energy Class

 

A

 

 

 

 

Annual Energy Consumption (kWh/year)*

528

 

 

 

 

 

 

Fridge Compartment Volume (Net-lt)

385

 

 

 

 

 

 

 

Total Frozen Food Compartment Volume

155

 

 

(Net-lt)

 

 

 

 

 

 

 

 

 

 

Multi Zone Volume (Net-lt)

77

 

 

 

 

 

 

 

Star Class

 

 

 

 

 

 

 

 

 

 

 

 

Temperature Increasing Time (hours)**

15

 

 

 

 

 

 

Freezing Capacity (kg/24 hours)

13

 

 

 

 

 

Climate Class

 

SN-T

 

 

 

 

Noise Level (dB(A))

43

 

 

 

 

 

 

Total Net Volume (lt)

540

 

 

 

 

 

 

(H) Height (cm)

182

 

 

 

 

 

 

(W) Width (cm)

92

 

 

 

 

 

 

(D) Depth (cm)

72

 

 

 

 

 

 

Weight (kg)

120

 

 

 

 

 

 

Total Power (W)

200

 

 

 

 

Electric Supply (V/Hz)

220-240/50

 

 

Coolant Type

R600a

 

 

 

 

 

*(Actual consumption varies depending on where and how the appliance is used)

**(Power failure safety; it is recommended not to consume the food in freezer compartment after this period.)

CTechnical specifications can be changed to increase the product quality without being subject to prior notice.

CValues stated on the markings on the product or in the printed materials supplied with the product are the values obtained in laboratory in accordance with relevant standards. Such values may vary depending on the usage of the product and the ambient conditions.

CThe dimensions given on the table describe the minimum required space to place the unit with doors closed.

4 EN

2 Warnings

Please review the following information. If these are not followed, personal injury or material damage may occur. Otherwise, all warranty and reliability commitments will become invalid.

The usage life of the unit you purchased is 10 years. This is the period for keeping the spare parts required for the unit to operate as described.

General safety

• When you want to dispose/scrap the product, we recommend you to consult the authorized service in

order to learn the required information and authorized bodies.

• Consult your authorized service for all your questions and problems related to the refrigerator. Do not intervene or let someone intervene to the refrigerator without notifying the authorized services.

• Do not eat cone ice cream and ice cubes immediately after you take them out of the freezer compartment! (This may cause frostbite in your mouth.)

• Do not put bottled and canned liquid beverages in the freezer compartment. Otherwise, these may burst.

• Do not touch frozen food by hand; they may stick to your hand.

• Vapor and vaporized cleaning materials should never be used in cleaning and defrosting processes of your refrigerator. In such cases, the vapor might get in contact with the electrical parts and cause short

circuit or electric shock.

5

Never use the parts on your refrigerator such as the door as a means of support or step.

Do not use electrical devices inside the refrigerator.

Do not damage the cooling circuit, where the refrigerant is circulating, with drilling or cutting tools. The refrigerant that might blow out when the gas channels of the evaporator, pipe extensions or surface coatings are punctured may cause skin irritations and eye injuries.

Do not cover or block the ventilation holes on your refrigerator with any material.

Repairs of the electrical appliances must only be made by qualified persons. Repairs performed by incompetent persons may create a risk for the user.

In case of any failure or during a maintenance or repair work,

disconnect your refrigerator’s mains supply by either turning off the relevant fuse or unplugging your appliance.

Do not pull by the cable when pulling off the plug.

Place the beverage with higher proofs tightly closed and vertically.

Flammable items or products that contain flammable gases (e.g. spray) as well as the explosive materials should never be kept in the appliance.

Do not use mechanical devices or other means to accelerate the

defrosting process, others than those recommended by the manufacturer.

EN

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance

Starting Up

Do not operate a damaged refrigerator. Consult your service if you have any doubts.

Electrical safety of your refrigerator shall be guaranteed only if the earth system in your house complies with standards.

Intended use

This product is designed for domestic use.

It should not be used outdoors. It is not appropriate to use it outdoor even if the place is covered with a roof.

Safety instructions

Exposing the product to rain, snow, sun and wind is dangerous with respect to electrical safety.

If there is any problem with the power cable or the plug, they must be replaced by the authorised service in order to avoid any accidents.

Caution: Never plug the refrigerator into the wall outlet during installation. Otherwise, risk of death or serious injury may arise.

Things to be done for energy saving

CDo not leave the doors of your refrigerator open for a long time.

CDo not put hot food or drinks in your refrigerator.

CDo not overload your refrigerator so that the air circulation inside of it is not prevented.

CDo not install your refrigerator under direct sunlight or near heat emitting appliances such as ovens, dishwashers or radiators.

CPay attention to keep your food in closed containers.

AYour product is equipped with a natural cooling system (R600a) which does not contain CFC and HFC gases. This gas is flammable. Therefore, pay attention to not damaging the cooling system and piping during usage and transportation. In the event of

damage, do not dispose the product in fire; keep your product away from potential fire sources that can cause the product catch a fire and ventilate the room in which the unit is placed.

6 EN

3 Installation

BPlease remember that the manufacturer shall not be held liable if the information given in the instruction manual is not observed.

Preparation

Your refrigerator should be installed at least 30 cm away from heat sources such as hobs, ovens, central heater and stoves and at least 5

cm away from electrical ovens and should not be located under direct sunlight.

The ambient temperature of the room where you install your

refrigerator should at least be 10°C. Operating your refrigerator under cooler conditions than this is not recommended with regard to its efficiency.

Please make sure that the interior of your refrigerator is cleaned thoroughly.

If two refrigerators are to be installed side by side, there should be at least 2 cm distance between them.

When you operate your refrigerator for the first time, please observe the following instructions during the initial six hours.

-The door should not be opened frequently.

-It must be operated empty without any food in it.

-Do not unplug your refrigerator. If

a power failure occurs out of your control, please see the warnings in the “Recommended solutions for the problems” section.

Original packaging and foam materials should be kept for future transportations or moving.

Points to be considered when re-transporting your refrigerator

1.Your refrigerator must be emptied and cleaned prior to any transportation.

2.Shelves, accessories, crisper and etc. in your refrigerator must be fastened securely by adhesive tape against any jolt before repackaging.

3.Packaging must be tied with thick tapes and strong ropes and the rules of transportation printed on the package must be followed.

Please do not forget…

Every recycled material is an indispensable source for the nature and for our national resources.

If you wish to contribute to recycling the packaging materials, you can get further information from the environmental bodies or local authorities.

7 EN

Before operating your refrigerator

Before starting to use your refrigerator check the following:

1.Is the interior of the refrigerator dry and can the air circulate freely in the rear of it?

2.Insert the 2 plastic wedges onto the rear ventilation as illustrated in the following figure. Unscrew the existing ones and use the screws given in the same bag of wedges. Plastic wedges will provide the required

distance between your refrigerator and the wall in order to allow the air circulation.

3.Clean the interior of the refrigerator as recommended in the “Maintenance and cleaning” section.

4.Plug the refrigerator into the wall outlet. When the door is open the respective interior light will come on.

5.You will hear a noise as the compressor starts up. The liquid and gases sealed within the refrigeration system may also give rise to noise, even if the compressor is not running and this is quite normal.

6.Front edges of the refrigerator may feel warm. This is normal. These areas are designed to be warm to avoid condensation.

Electric connection

Connect your refrigerator to a grounded socket which is being protected by a fuse with the appropriate capacity.

Important:

The connection must be in compliance with national regulations.

The power cable plug must be easily accessible after installation.

Voltage and allowable fuse protection are specified in the “Technical Specifications” section.

The specified voltage must be equal to your mains voltage.

Extension cables and multiway plugs must not be used for connection.

BA damaged power cable must be replaced by a qualified electrician.

BThe appliance must not be operated before it is repaired! There is danger of electric shock!

Disposing of the packaging

The packing materials may be dangerous for children. Keep the packing materials out of the reach of children or dispose them of by classifying them in accordance with the waste instructions. Do not

dispose them of along with the normal household waste.

The packing of your refrigerator is produced from recyclable materials.

Disposing of your old refrigerator

Dispose of your old machine without giving any harm to the environment.

You may consult your authorized dealer or waste collection center of your municipality about the disposal of your refrigerator.

8 EN

Before disposing of your refrigerator, cut out the electric plug and, if there are any locks on the door, make them inoperable in order to protect children against any danger.

Placing and Installation

Caution: Never plug the refrigerator into the wall outlet during installation. Otherwise, risk of death or serious injury may arise.

If the entrance door of the room where the refrigerator will be installed is not wide enough for the refrigerator to pass through, than call the authorized service to have them remove the doors of your refrigerator and pass it sideways through the door.

1.Install your refrigerator to a place that allows ease of use.

2.Keep your refrigerator away from heat sources, humid places and direct sunlight.

3.There must be appropriate air ventilation around your refrigerator in order to achieve an efficient operation.

If the refrigerator is to be placed in a recess in the wall, there must be at least 5 cm distance with the ceiling and at least 5 cm with the wall.

If the floor is covered with a carpet, your product must be elevated 2.5 cm from the floor.

4.Place your refrigerator on an even floor surface to prevent jolts.

5.Do not keep your refrigerator in ambient temperatures under 10°C.

Floor balance adjustment

If your refrigerator is unbalanced;

1- Ventilation cover is removed by unscrewing its screws as illustrated in the figure before the procedure. You can balance your refrigerator by turning the front legs of it as illustrated in the figure. The corner where the leg exists is lowered when you turn

in the direction of black arrow and raised when you turn in the opposite direction. Taking help from someone to slightly lift the refrigerator will facilitate this process.

2. After the balance issue is remedied, install back the ventilation cover and fasten the screws.

4

1 2 3

3. Remove the screws fastening the lower ventilation cover using a Philips screwdriver.

9 EN

Adjusting the gap between the upper door

• You can adjust the gap between the fridge compartment doors as illustrated in the figures.

Door shelves should be empty when adjusting the door height.

• Using a screwdriver, remove the screw of upper hinge cover of the door you want to adjust.

CenterMerkezScrewVida

• Adjust the door as you desire by loosing the screws.

• Fix the door you have adjusted by tightening the screws without changing the position of the door.

• Replace the hinge cover and fix with the screw.

10 EN

4 Using your refrigerator

Indicator Panel

This touch-control indicator panel allows you to set the temperature without opening the door of your refrigerator. Just touch the relevant button with your finger to set the temperature.

1

7

11

12 15

4

2

5

 

16

3

6

10 9 8 14 13

1.

Eco Extra/Vacation Button

9.

Quick Freeze Function

2.

Fast Freeze Button

Indicator

3.

Freezer Compartment

10.

Freezer Compartment

Temperature Setting Button

Temperature Indicator

4.

Fridge Compartment

11.

Fridge Compartment

Temperature Setting Button

Temperature Indicator

5.

Quick Cool Button

12.

Quick Cool Function Indicator

6.

Multi Zone Storage

13.

Multi Zone Storage

Compartment Temperature Setting

Compartment Temperature Indicator

Button

 

14.

Economy Mode Indicator

7.

Vacation Function Indicator

15.

Error Status Indicator

8.

Eco Extra Function Indicator

16.

Key Lock Indicator

11 EN

1.Eco Extra/Vacation Button

Press this button briefly to activate the Eco Extra function. Press and hold this button for 3 sec. to activate the Vacation function. Press this button again to deactivate the selected function.

2.Fast Freeze Button

Press this button briefly to activate the Fast Freeze function. Press this

button again to deactivate the selected function.

3.Freezer Compartment Temperature Setting Button

Press this button to set the temperature of the freezer compartment to -18, -20, -22, -24, -18... respectively. Press this button to set the desired temperature for the Freezer Compartment.

4.Fridge Compartment Temperature Setting Button

Press this button to set the temperature of the fridge compartment to 8, 6, 4, 2, 8... respectively.

Press this button to set the desired temperature for the Fridge Compartment.

5.Quick Cool Button

Press this button briefly to activate the Quick Cool function. Press this

button again to deactivate the selected function.

6. Multi Zone Storage Compartment Temperature Setting Button

You can set the Multi Zone Storage

Compartment either as a Freezer or a Cooler. Press and hold this button for 3 sec. to set the Multi Zone Storage Compartment either as a Freezer or a Cooler. This compartment is set as a Freezer Compartment at factory.

If the Multi Zone Storage Compartment is set as a Freezer, then the temperature of the Multi Zone Storage Compartment will change as -18,

-20, -22, -24, -18... respectively each time you press this button. If the Multi Zone Storage Compartment is set

as a Cooler, then the temperature of the Multi Zone Storage Compartment will change as 10, 8, 6, 4, 2, 0, -6,...

respectively each time you press this button.

7. Vacation Function Indicator

Indicates that the vacation function is active. If this function is active, ì- -ì appears on the indicator of the

fridge compartment and no cooling is performed in the fridge compartment. Other compartments will be cooled in accordance with the temperature set for them.

Press the relevant button again to deactivate this function.

8. Eco Extra Function Indicator

Indicates that the Eco Extra function is active. If this function is active, your refrigerator will automatically detect the least usage periods and energyefficient cooling will be performed during those times. Economy indicator will be active while energy-efficient cooling is performed.

Press the relevant button again to deactivate this function.

12 EN

Loading...
+ 29 hidden pages