Beko GN1306230ZDX User manual [EN,DE,ES]

GN1306230ZDX

Please read this manual before using the product!

Dear Customer, We'd like you to make the best use of our product, which has been manufactured in modern facilities

with care and meticulous quality controls. Thus, we advice you to read the entire user manual before you use the product. In case the product

changes hands, do not forget to hand the guide to its new owner along with the product.

This guide will help you use the product quickly and safely.

• Please read the user guide carefully before installing and operating the product.

• Always observe the applicable safety instructions.

• Keep the user guide within easy reach for future use.

• Please read any other documents provided with the product.

Keep in mind that this user guide may apply to several product models. The guide clearly indicates any variations of different models.

Important information and useful

tips.

Risk of life and property.

Risk of electric shock.

The product’s packaging is made of recyclable materials, in accordance with the National Environment Legislation.

1. Safety and environment instructions 3

2 Your Refrigerator 6

3 Installation 7

3.1 Appropriate installation location . . . . . . . . .7

3.2 Installing the plastic wedges. . . . . . . . . . . .7

3.3 Electrical connection . . . . . . . . . . . . . . . . .7

3.4 Adjusting the feet. . . . . . . . . . . . . . . . . . . .8

3.5 Illumination lamp . . . . . . . . . . . . . . . . . . . .8

3.6 Door open warning. . . . . . . . . . . . . . . . . . .8

3.7 Water connection. . . . . . . . . . . . . . . . . . . .9

3.7.1 Before Installation . . . . . . . . . . . . . . . . . .10

3.8 Connecting the water hose to the

refrigerator . . . . . . . . . . . . . . . . . . . . . . .10

3.9 Connecting the water line to the water

supply. . . . . . . . . . . . . . . . . . . . . . . . . . .10

3.10 Water filter . . . . . . . . . . . . . . . . . . . . . . . .10

3.10.1 Attaching the internal filter into the

refrigerator . . . . . . . . . . . . . . . . . . . . . . .10

3.11 Connecting the water hose to demijohn . .12

3.12 Before starting to use the water/ice

dispenser . . . . . . . . . . . . . . . . . . . . . . . .13

3.13 Transportation of the product . . . . . . . . . .14

4 Preparation 15

4.1 Things to be done for energy saving. . . . .15

4.2 Recommendations for the fresh food

compartment. . . . . . . . . . . . . . . . . . . . . .15

4.3 Initial use. . . . . . . . . . . . . . . . . . . . . . . . .16

5 Operating the product 20

5.1 Indicator panel. . . . . . . . . . . . . . . . . . . . .20

5.2 Indicator panel . . . . . . . . . . . . . . . . . . . . . .22

5.3 Dual cooling system. . . . . . . . . . . . . . . . .26

5.4 Freezing fresh food . . . . . . . . . . . . . . . . .26

5.5 Recommendations for preserving the frozen

food . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

5.6 Placing the food. . . . . . . . . . . . . . . . . . . .27

5.7 Deep-freeze information. . . . . . . . . . . . . .27

5.8 Removing door shelves . . . . . . . . . . . . . .29

5.9 Moving door rack . . . . . . . . . . . . . . . . . . . .29

5.10 Glass shelves. . . . . . . . . . . . . . . . . . . . . .29

5.11 Chiller compartment. . . . . . . . . . . . . . . . .29

5.12 Crisper . . . . . . . . . . . . . . . . . . . . . . . . . .30

5.13 Humidity controlled crisper . . . . . . . . . . . .30

(FreSHelf). . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

5.14 Ice container . . . . . . . . . . . . . . . . . . . . . .30

5.15 Butter & Cheese section . . . . . . . . . . . . .31

5.16 Egg holder. . . . . . . . . . . . . . . . . . . . . . . .31

5.17 Movable middle section . . . . . . . . . . . . . .31

5.18 Blue light. . . . . . . . . . . . . . . . . . . . . . . . .31

5.19 Ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

5.20 Odour filter . . . . . . . . . . . . . . . . . . . . . . .32

5.21 Using internal water dispenser . . . . . . . . .32

5.22 Dispensing Water. . . . . . . . . . . . . . . . . . .32

5.23 For using water dispenser. . . . . . . . . . . . .32

5.24 Icematic . . . . . . . . . . . . . . . . . . . . . . . . .33

5.25 Icematic and ice storage container . . . . . .33

5.26 Refrigerator Shelf Weight Limitations. . . . .34

6. Maintenance and cleaning 35

6.1 Avoiding bad odors . . . . . . . . . . . . . . . . .35

6.2 Protecting the plastic surfaces . . . . . . . . .35

7. Troubleshooting 36

2 /37 EN

Refrigerator / User Manual

1. Safety and environment instructions

This section provides the safety instructions necessary to prevent the risk of injury and material damage. Failure to observe these instructions will invalidate all types of product warranty.

Intended use

WARNING:

Keep ventilation openings, in the appliance enclosure or in

the built-instructure, clear of obstruction.

WARNING:

Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

WARNING:

Do not damage the refrigerant circuit.

WARNING:

Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

mental disabilities, without sufficient knowledge and experience or by children. The device can only be used by such persons under supervision and instruction of a person responsible for their safety. Children should not be allowed to play with this device.

• In case of malfunction, unplug the

device.

• After unplugging, wait at least 5

minutes before plugging in again.

• Unplug the product when not in use.

• Do not touch the plug with wet hands!

Do not pull the cable to plug off, always hold the plug.

• Do not plug in the refrigerator if the

socket is loose.

• Unplug the product during installation,

maintenance, cleaning and repair.

• If the product will not be used for a

while, unplug the product and remove any food inside.

• Do not use the product when the

compartment with circuit cards located on the upper back part of the product (electrical card box cover) (1) is open.

This appliance is intended to be used in household and similar applications such as – staff kitchen areas in shops, offices and other working environments; – farm houses and by clients in hotels, motels and other residential type environments; – bed and breakfast type environments; – catering and similar non-retail applications.

1.1. General safety

• This product should not be used by

persons with physical, sensory and

• Do not use steam or steamed cleaning

materials for cleaning the refrigerator and melting the ice inside. Steam may contact the electrified areas and cause short circuit or electric shock!

• Do not wash the product by spraying or

3 / 37 EN

pouring water on it! Danger of electric shock!

Refrigerator / User Manual

Important instructions for safety and environment

• In case of malfunction, do not use the

product, as it may cause electric shock. Contact the authorised service before doing anything.

• Plug the product into an earthed

socket. Earthing must be done by a qualified electrician.

• If the product has LED type lighting,

contact the authorised service for replacing or in case of any problem.

• Do not touch frozen food with wet

hands! It may adhere to your hands!

• Do not place liquids in bottles and cans

into the freezer compartment. They may explode.

• Place liquids in upright position after

tightly closing the lid.

• Do not spray flammable substances

1.1.1 HC warning

If the product comprises a cooling system using R600a gas, take care to avoid damaging the cooling system and its pipe while using and moving the product. This gas is flammable. If the cooling system is damaged, keep the product away from sources of fire and ventilate the room immediately.

near the product, as it may burn or explode.

• Do not keep flammable materials and

products with flammable gas (sprays, etc.) in the refrigerator.

• Do not place containers holding liquids

on top of the product. Splashing water on an electrified part may cause electric shock and risk of fire.

• Exposing the product to rain, snow,

sunlight and wind will cause electrical danger. When relocating the product, do not pull by holding the door handle. The handle may come off.

• Take care to avoid trapping any part

of your hands or body in any of the moving parts inside the product.

• Do not step or lean on the door,

drawers and similar parts of the refrigerator. This will cause the product to fall down and cause damage to the parts.

• Take care not to trap the power cable.

1.1.2 For models with

water dispenser

• Pressure for cold water inlet shall be

maximum 90 psi (6.2 bar). If your water pressure exceeds 80 psi (5.5 bar), use a pressure limiting valve in your mains system. If you do not know how to check your water pressure, ask for the help of a professional plumber.

• If there is risk of water hammer effect

in your installation, always use a water hammer prevention equipment in your installation. Consult Professional plumbers if you are not sure that there is no water hammer effect in your installation.

• Do not install on the hot water inlet.

Take precautions against of the risk of freezing of the hoses. Water temperature operating interval shall be 33°F (0.6°C) minimum and 100°F (38°C) maximum.

• Use drinking water only.

4 /37 EN

The label on the inner left side indicates the type of gas used in the product.

Refrigerator / User Manual

Important instructions for safety and environment

1.2. Intended use

• This product is designed for home use.

It is not intended for commercial use.

• The product should be used to store

food and beverages only.

• Do not keep sensitive products

requiring controlled temperatures (vaccines, heat sensitive medication, medical supplies, etc.) in the refrigerator.

• The manufacturer assumes no

responsibility for any damage due to

1.5. Compliance with RoHS Directive

• This product complies with EU WEEE Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

1.6. Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

misuse or mishandling.

• Original spare parts will be provided

for 10 years, following the product purchasing date.

1.3. Child safety

• Keep packaging materials out of

children’s reach.

• Do not allow the children to play with

the product.

• If the product’s door comprises a lock,

keep the key out of children’s reach.

1.4. Compliance with WEEE Directive and Disposing of the Waste Product

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its

service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.

5 / 37 EN

Refrigerator / User Manual

2 Your Refrigerator

*13

*11

14 15

*17

1- Fridge compartment 2- ButFreezer compartment 3- Display/indicator panel 4- Butter & cheese section 5- Fridge compartment door shelf 6- Eggy tray 7- Bottle shelf 8- Chiller compartment

Figures in this user manual are schematic and may not match the product exactly. If the subject parts are not included in the product you have purchased, then those parts are valid for other models.

9- Crispers 10- İnner water dispenser 11- Adjustable glass shelf 12- Blower 13- Water filter 14- Ice container 15- Frozen food storage compartment (upper) 16- Frozen food storage compartment (upper) 17- Seperator

6 /37 EN

Refrigerator / User Manual

3 Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, make sure that the electricity installation is appropriate before calling the Authorised Service Agent. If not, call a qualified electrician to have any necessary arrangements carried out.

Preparation of the location and electrical installation at the place of installation is

B A

under customer's responsibility. Product must not be plugged in during

installation. Otherwise, there is the risk of death or serious injury!

WARNING: Installation and electrical

connections of the product must be carried out by the Authorised Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

WARNING: Prior to installation, visually

check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

Make sure that the power cable is not pinched or crushed while pushing the product into its place after installation or cleaning procedures.

3.1 Appropriate installation location

WARNING: If the door of the room where

the product will be placed is too small for the product to pass, then the product's

•Chooseaplaceatwhereyouwouldusethe

product comfortably.

•Installtheproductatleast30cmawayfrom

heat sources such as hobs, ovens, heater cores and stoves and at least 5 cm away from electrical ovens. Product must not be subjected to direct sun light and kept in humid places after installation.

•Appropriateairventilationmustbeprovided

around your product in order to achieve an efficient operation. If the product is to be placed in a recess in the wall, pay attention to leave at least 5 cm distance with the ceiling and side walls.

doors must be removed and the product must be turned aside to pass it through.

•Donotplacetheproductonthematerialssuch

as rugs or carpets.

•Placetheproductonanevenfloorsurfaceto

prevent jolts.

•Donotinstalltheproductinplaceswherethe

temperature falls below 10ºC /50°F.

If two coolers are to be installed side by side, there should be at least 4 cm

distance between them.

3.2 Installing the plastic wedges

Plastic wedges are used to create the distance for the air circulation between the product and the rear wall. Insert the 2 plastic wedges onto the rear ventilation cover as illustrated in the figure. To install the wedges, remove the screws on the product and use the screws given in the same pouch with the wedges.

3.3 Electrical connection

Connect the product to a grounded outlet protected by a fuse complying with the values in the rating plate. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

•Electricalconnectionmustcomplywithnational

regulations.

•Powercableplugmustbewithineasyreach

after installation.

•Thevoltageandallowedfuseorbreaker

protection are specified in the Rating Plate which is affixed to interior of the product. If the current value of the fuse or breaker in the house does not comply with the value in the rating plate, have a qualified electrician install a suitable fuse.

•Thespecifiedvoltagemustbeequaltoyour

mains voltage.

•Donotmakeconnectionsviaextensioncables

or multi-plugs.

7 / 37 EN

Refrigerator / User Manual

Installation

WARNING: Damaged power cable must

be replaced by the Authorised Service

B B

Agents.

WARNING: If the product has a failure, it

should not be operated unless it is repaired by the Authorised Service Agent! There is the risk of electric shock!

3.4 Adjusting the feet

If the product stands unbalanced after installation adjust the feet. Taking help from someone to slightly lift the refrigerator will facilitate this process.

WARNING: First unplug the product.

Product must not be plugged in when

Turn the front feet to balance the product. The corner where the foot exists is lowered when you turn in the direction of arrow and raised when you turn it in the opposite direction.

adjusting the feet. There is the risk of electric shock!

3.6 Door open warning

(This feature may vary depending on the door of the product and may not exist in some models.)

An audio warning signal will be given when the door of your product is left open for 1 minute. This warning will be muted when the door is closed or any of the display buttons (if any) are pressed.

3.5 Illumination lamp

Do not attempt to repair yourself but call the Authorised Service Agent if the LED illumination lamps do not go on or are out of order. The lamp(s) used in this appliance is not suitable for household room illumination. The intended purpose of this lamp is to assist the user to place foodstuffs in the refrigerator/freezer in a safe and comfortable way.

8 /37 EN

Refrigerator / User Manual

Installation

-Upper hinge group is fixed with 3 screws.

-The hinge cover is attached after the sockets are installed.

- Then the hinge cover is fixed with two screws.

3.7 Water connection

Depending on the model of the refrigerator, you can connect it either to a demijohn or water mains. First you must connect the water hose to the refrigerator.

In cases where a demijohn is used, a

C A C

Check that following part have been delivered together with the product:

External water filter. (If there is a demijohn

connection; it is not necessary to use a water filter.)

separate pump must also be used.

WARNING: Refrigerator and the pump, if

any, must be unplugged during connection.

Following parts may not be supplied with your product since they are not required when using a demijohn.

9 / 37 EN

Refrigerator / User Manual

Installation

3.7.1 Before Installation

Make sure that you have everything necessary to ensure proper installation before proceeding, including:

Your product comes with an internal water filter for

use inside the fridge. Part number of the filter is 4918450200 and you can use this part number

when ordering replacement filters.

3.8 Connecting the water hose to the refrigerator

1. Slip the union (B) onto the water hose (A).

2. Push the water hose downwards firmly to slip it

onto the water inlet valve (C).

3. Tighten the union (C) by hand to secure it onto

the water inlet valve.

Normally, you are not required to tighten the union with a tool. However, you can use

a spanner or pliers to tighten the union if there is a leakage.

3.10.1 Attaching the internal filter into the refrigerator

1. Pull the water filter cover slowly.

2. Remove the water filter bypass cover by turning

it downwards.

3.9 Connecting the water line to the water supply

Connect the water line to a water supply valve. If a valve is not present or you are not sure, consult a qualified plumber.

3.10 Water filter

(in some models)

Your refrigerator may be equipped with an external or internal filter depending on its model. To fit the water filter, follow the instructions below referring to the figures supplied:

10 /37 EN

Refrigerator / User Manual

Installation

WARNING: Ensure that the Ice Off mode

is enabled before removing the by-pass

3. Seat the water filter cover into the mechanism and push forwards to lock it in place.

4. Press “Ice Off” button on the display again to exit this mode.

cover.

It is normal that a few drops of water drip after the cover has been removed.

WARNING: Ensure that the Ice Off mode

is enabled before removing the by-pass

3. Seat the water filter cover into the mechanism and push forwards to lock it in place.

4. Press “Ice Off” button on the display again to exit this mode.

A A

cover.

It is normal that a few drops of water drip after the cover has been removed.

Water filter must be replaced every 6 months. When replacing the water filter or if you will not use the filter anymore, remove it as illustrated in the figure and install the bypass cover. Make sure that the "Ice Off" mode is enabled before removing the filter.

WARNING: Water filter cleans some

foreign particles in the water. It does not purify water from microorganisms.

WARNING: Ice Off button must be

pressed before replacing the water filter or installing the by-pass cover.

WARNING: Unplug the product during the

replacement of the filter.

11 / 37 EN

Refrigerator / User Manual

Installation

3.11 Connecting the water hose to demijohn

(in some models)

To make the water supply connection between the refrigerator and the demijohn, you must use a water pump. Follow the instructions below after connecting one end of the water hose coming out of the pump to the refrigerator.

1. Complete the connection by pushing the other

end of the water hose into the water hose inlet of the pump.

2. Put and fix the pump hose into the demijohn.

3. After completing the connection, plug in and run

the pump.

After the pump starts to operate, wait for 2-3 minutes to allow it attain the required

C C C

efficiency.

You can refer to the user manual of the pump while making the water connection.

There is no need to use water filter if you will be using a demijohn.

12 /37 EN

Refrigerator / User Manual

Installation

3.12 Before starting to use the water/ice dispenser

• If the water pressure is below 1 bar or a

demijohn will be used, than a separate must be used as well.

• Water system of the refrigerator must be

connected to the cold water line. It must not be

connected to hot water line.

• No water may be obtained in the initial start-up

of the refrigerator. Because there is air in the system. To discharge air from the system, press dispenser latch for 1-2 minutes until water comes from the dispenser. Water flow may be irregular at the beginning. After the air in the system is discharged, water flow will return to normal.

• During initial use, you will have to wait

approximately 12 hours for the water to cool down.

• It will take around 1-2 days for the system to

produce required amount of ice.

• The first 10 glasses of water should not be

consumed.

• First several glasses of water may be turbid

when the filter is used for the first time.

Therefore, do not consume the first several glasses of water.

• If the water dispenser is not used for a long period of time, first 1-2 glasses of water can be hot.

• If a power outage or a temporary failure occurs while the refrigerator is operating, ice can melt down a little bit and then get frozen again. In such a case, ice cubes can stick to each other. If the outage or failure prolongs, ice can melt down causing water leakage. If you experience such a problem, empty and clean the ice container.

• Ice cubes can stick to each other if they are left in the container for a long time.

• Water system installation of the refrigerator must be performed by the Authorised Service Agent.

• If the product is to be connected to the water mains, make sure that you use potable water.

• Water system of the product is designed to operate only with water. Do not use beverage such as soft drinks and/or juices in the water system.

• It is recommended that the water is disconnected if you will not be using the refrigerator for a long period of time due to vacation or similar reasons.

• Do not attempt to dismantle the ice container group assembly parts.

• Do not attempt to clean the ice container assembly without removing it from the refrigerator.

13 / 37 EN

Refrigerator / User Manual

Installation

• When taking water from the water dispenser, remove the glass from the opening 1 second after releasing the trigger. Thus, water in the system will not drip into the drip tray.

3.13 Transportation of the product

1. Unplug the product before transporting it.

2. Remove water connections.

3. Secure the shelves, accessories, crisper and

etc. in the refrigerator by adhesive tape before repackaging it.

Packaging must be tied with thick tapes or strong ropes and the rules of transportation

C C

printed on the package must be followed.

Original packaging and foam materials should be kept for future transportations.

WARNING: Packaging materials

are dangerous for the children. Keep packaging materials in a safe place away from reach of the children.

14 /37 EN

Refrigerator / User Manual

4 Preparation

4.1 Things to be done for energy saving

Connecting the product to electric energy saving systems is risky as it may cause

• Do not leave the doors of your refrigerator open

• Do not put hot food or drinks in your

• Do not overload the refrigerator. Cooling

• Do not place the refrigerator in places subject

• Pay attention to store your food in refrigerator

• You can load maximum amount of food to the

• Thawing frozen food in fridge compartment will

damage on the product.

for a long time.

refrigerator.

capacity will fall when the air circulation inside is hindered.

to direct sunlight. Install the product at least 30 cm away from heat sources such as hobs, ovens, heater cores and stoves and at least 5 cm away from electrical ovens.

in closed containers.

freezer compartment of the refrigerator by removing the freezer compartment shelf of drawer. Declared energy consumption value of the refrigerator was determined with the freezer compartment shelf or drawer removed and with maximum amount of food loaded. There is no risk in using a shelf or drawer suitable for the shapes and sizes of the foods to be frozen.

both provide energy saving and preserve the food quality.

The ambient temperature of the room where you install the refrigerator should

at least be 10ºC /50°F. Operating your refrigerator under cooler conditions than this is not recommended.

4.2 Recommendations for the fresh food compartment

• Do not allow the food to touch the temperature

sensor in fresh food compartment. To allow the fresh food compartment keep its ideal storage temperature, sensor must not be hindered by food.

• Do not put hot food and beverages inside the

product.

C C

Inside of your refrigerator must be cleaned thoroughly.

If two coolers are to be installed side by side, there should be at least 4 cm distance between them.

15 / 37 EN

Refrigerator / User Manual

Preparation

4.3 Initial use

Before starting to use the product, check that all preparations are made in accordance with the instructions in sections "Important instructions for safety and environment" and "Installation".

• Clean the interior of the refrigerator as recommended in the “Maintenance and cleaning” section. Check that inside of it is dry before operating it.

• Plug the refrigerator into the grounded wall outlet. When the door is opened the interior illumination will turn on.

• Run the refrigerator without putting any food for 6 hours and do not open its door unless certainly required.

You will hear a noise when the compressor starts up. The liquids and gases sealed

C C

within the refrigeration system may also give rise to noise, even if the compressor is not running and this is quite normal.

Front edges of the refrigerator may feel warm. This is normal. These areas are designed to be warm to avoid condensation.

16 /37 EN

Refrigerator / User Manual

Preparation



DIMENSIONS [36”FRENCHREFRIGERATOR]



PRODUCTDIMENSIONS



17 / 37 EN

Refrigerator / User Manual

Preparation

Overall

TopOfCabinet



WithHandles

Cabinet

DrawerOpen

Open90°WithHandles



FreezerDoorOpenMax(Drawer)

DIMENSIONS [36”FRENCHREFRIGERATOR]



Height

"A"

1771mm(69,72") 1710mm(67,32") 600mm(23,62") 680,5mm(26,79")

   

Depth

"E"

737mm(29,01") 908mm(35,74") 1157mm(45,55") 1178,5mm(46,40”)

   

DepthDoorsOpen90°

"I"

1072,6mm(42,22") 1094mm(43,07") 1059,2mm(41,70") 75,6mm(2,97")

   

WidthDoorsOpen130°

FromHandleToHandle

"M"

1530.2mm(41,70") 311,2mm(12,25") 391mm(15,39") 991mm(39.01")

Min Clearance From the Top: 2 inches

Height

"B"

Width

"F"

TotalDepthDoors

Open90°"J"

WidthDoorsOpen130°

FromCabinetToHandle

"N"

DepthCabinetOnly

"C""O"

Depth

WidthDoors

DepthDoorsOpen130°



Min Clearance From the Sides: 2 inches

18 /37 EN

"G"

"K"

"P"

DepthWithoutHandles

"D"

TotalDepthDrawerOpen

"H"

WidthDoorsOpen90° FromCabinetToHandle

"L"

DepthDoorsOpen130°

"R"

Refrigerator / User Manual

Preparation



FreshFoodDoorOpen90°



DIMENSIONS [36”FRENCHREFRIGERATOR]



FreshFoodDoorOpen130°(Max)

19 / 37 EN



Refrigerator / User Manual

5 Operating the product

5.1 Indicator panel

Touch-control indicator panel allows you to set the temperature and control the other functions of the refrigerator. Just press the relevant buttons for function settings.

4 5 6

1-On/Off function

Press the On/Off button for 3 seconds to turn off or turn on the fridge.

2-Quick Fridge Function

When you press Quick Fridge button, the temperature of the compartment will be colder than the adjusted values. This function can be used for food placed in the fridge compartment and required to be cooled down rapidly. If you want to cool large amounts of fresh food, it is recommended to active this feature before putting the food into the fridge. Quick Fridge indicator will remain lit when the Quick Fridge function is enabled. To cancel this function press Quick Fridge button again. Quick Fridge indicator will turn off and return to its normal settings. If you do not cancel it, Quick Fridge will cancel itself automatically after 2 hours or when the fridge compartment reaches to the required temperature. This function is not recalled when power restores after a power failure.

3-Vacation Function

Press the Quick Fridge\Vacation button for 3 seconds to activate Vacation function.”--” icon comes on when the function is active. Function is deactivated by pressing the same button for 3 seconds again or by pressing Fridge set button. When vacation mode is activated, set values does not seem for fresh food cabin. Line is occured on segments of fresh food. When vacation mode is activated, tempature of fresh food is hotter than 50 Fahrenheit degree(

10 celcius degree) so please do not keep foods in fresh food cabinet. Tempature of freezer is not affected.

4-Fridge Set Function

This function allows you to make the fridge compartment temperature setting. Press this button to set the temperature of the fridge compartment to

8, 7, 6, 5, 4, 3, 2 or 1°C respectively.

5-Off Indicator

Off Indicator lits when the fridge is “Off” mode.

6-Quick Fridge Indicator

This icon lits when the Quick Fridge function is active.

7-Fridge Compartment Temperature Setting Indicator

Indicates the temperature set for the Fridge Compartment.

8-Vacation Indicator

This icon lits when the Vacation function is active.

9-High Temperature Error / Warning Indicator

This icon comes on during high temperature failures and error warnings.

10-Freezer Compartment

Temperature Setting Indicator Indicates the temperature set for the Freezer Compartment.

11-Eco-Extra Indicator

Eco-Extra Indicator lits when the Eco Extra function is active.

12-Quick Freeze Indicator

14 15 16

Figures in this user manual are schematic and may not match the product exactly. If the subject parts are not included in the product you have purchased, then those parts are valid for other models.

20 /37 EN

Refrigerator / User Manual

Operating the product

This indicator lits when the Quick Freezer function is active.

13-Freezer Set Function

This function allows you to make the freezer compartment temperature setting. Press this button to set the temperature of the freezer compartment to 0, -2, -4, -6, -8, -10 and -12 respectively.

14-Quick Freeze Function

Quick Freeze indicator turns on when the Quick Freeze function is on. To cancel this function press Quick Freeze button again. Quick Freeze indicator will turn off and return to its normal settings. If you do not cancel it, Quick Freeze will cancel itself automatically after 4 hours or when the freezer compartment reaches to the required temperature. If you want to freeze large amounts of fresh food, press the Quick Freeze button before putting the food into the freezer compartment. If you press the Quick Freeze button repeatedly with short intervals, the electronic circuit protection will be activated immediately. This function is not recalled when power restores after a power failure.

15-Eco-Extra (Special Economic Usage) Function

Press the Quick Freeze\Eco Extra button for 3 seconds to activate the Eco Extra Function. Refrigerator will start operating in the most economic mode at least 6 hours later and the economic usage indicator will turn on when the function is active. Press the Quick Freeze button for 3 seconds again to deactivate the Eco Fuzzy Function.

16-Alarm Off

When the fridge door is opened for 2 minutes or when there a sensor failure, a sound alarm turns on. Alarm can be turned off by pressing “Alarm Off” button. Sensor failure alarm will not sound till power failure. If you close the door and then open again “Door open alarm” will be activated again after 2

minutes later .

21 / 37 EN

Refrigerator / User Manual

Operating the product

5.2 Indicator panel

Touch-controlled indicator panel allows you to set the temperature and control the other functions related to the refrigerator without opening the door of the product. Just press the relevant buttons for function settings.

2 3

5 6

10 11

31 30

Select

3 “

*34.1

*34.2

Quick FreezeQuick Cool

3 “

1718

Quick FreezeQuick Cool

3 “

*25

Figures in this user manual are schematic and may not match the product exactly. If the subject parts are not included in the product you have purchased, then those parts are valid for other models.

22 /37 EN

Refrigerator / User Manual

Operating the product

1. Quick cooling function indicator

It turns on when the quick fridge function is activated.

2. Fridge compartment temperature indicator

Temperature of the fridge compartment is shown; it can be set to 8,7,6,5,4,3,2,1.

3. Fahrenheit indicator

It is a Fahrenheit indicator. When the Fahrenheit indication is activated, the temperature set values are shown in Fahrenheit and the relevant icon turns on.

4. Key lock

Press key lock button simultaneously for 3 seconds. Key lock symbol

will light up and key lock mode will be activated. Buttons will not function if the Key lock mode is active. Press key lock button simultaneously for 3 seconds again. Key lock symbol will turn off and the key lock mode will be exited.

Press the key lock button if you want to prevent changing of the temperature setting of the refrigerator.

5. Power failure/High temperature / error warning

This indicator illuminates during power failure, high temperature failures and error warnings. During long-term power failures, the highest temperature value that the freezer compartment reaches will blink on the digital display. After checking the food located in the freezer compartment, press the alarm off button to clear the warning.

Please refer to "solutions recommended for troubleshooting" section on your manual if you observe that this indicator is illuminated.

6. Filter reset icon

This icon turns on when the filter needs to be reset.

7. Temperature change cabin icon

Indicates the cabin whose temperature is to be changed. When the temperature change cabin icon starts flashing, it is understood that the relevant cabin has been selected.

8. Joker freezer icon

Hover over the Joker freezer icon using the FN button; the icon will start to flash. When you press the OK key, joker

cabin freezer icon turn on and operates as a freezer.

9. Freezer compartment temperature indicator

Temperature of the fridge compartment is shown; it can be set to -18, -19, -20, -21, -22, -23, -24.

10. Quick freeze function indicator

It turns on when the quick freeze function is activated.

11. Fahrenheit indicator

It is a Fahrenheit indicator. When the Fahrenheit indication is activated, the temperature set values are shown in Fahrenheit and the relevant icon turns on.

12. Quick freeze function button

Press this button to activate or deactivate the quick freeze function. When you activate the function, the freezer compartment will be cooled to a temperature lower than the set value.

Use the quick freeze function when you want to quickly freeze the food placed

C C

13. Filter reset

The filter is reset when the quick freeze button is pressed for 3 seconds. Filter reset icon goes off.

14. FN button

Using this key, you can switch between the functions that you want to select. Upon pressing this key, the icon, whose function is required to be activated or deactivated, and this icon's indicator

in freezer compartment. If you want to freeze large amounts of fresh food, activate this function before putting the food into the product.

If you do not cancel it, Quick Freeze will cancel itself automatically after 4 hours at the most or when the fridge compartment reaches to the required temperature.

This function is not recalled when power restores after a power failure.

23 / 37 EN

Refrigerator / User Manual

Operating the product

starts flashing. The FN button gets deactivated if not pressed for 20 seconds. You need to press this button to change the functions again.

15. Celsius indicator

It is a Celsius indicator. When the Celsius indication is activated, the temperature set values are shown in Celsius and the relevant icon turns on.

16. OK button

After navigating the functions using the FN button, when the function is cancelled via the OK button, the relevant icon and the indicator flashes. When the function is activated, it remains on. The indicator continues to flash in order to show the icon it is on.

17. Temperature change cabin icon

Indicates the cabin whose temperature is to be changed. When the temperature change cabin icon starts flashing, it is understood that the relevant cabin has been selected.

18. Temperature change cabin icon

Indicates the cabin whose temperature is to be changed. When the temperature change cabin icon starts flashing, it is understood that the relevant cabin has been selected.

19. Set increasing button

Select the relevant cabin with the select button; the cabin icon representing the relevant cabin will start to flash. If you press the set increasing button during this process, the set value gets increased. If you keep pressing it in a loop, the set value returns to the beginning.

20. Temperature change cabin icon

Indicates the cabin whose temperature is to be changed. When the temperature change cabin icon starts flashing, it is understood that the relevant cabin has been selected.

21. Setting the Celsius and Fahrenheit

indicator

Hover over this key using the FN key and select Fahrenheit and Celsius via the OK key. When the relevant temperature type is selected, the Fahrenheit and Celsius indicator turns on.

24 /37 EN

22. Ice machine off icon

Press the FN key (until it reaches the ice icon and the lower line) to switch off the ice machine. The ice machine off icon and the ice machine function indicator start flashing when you hover over them, thus you can understand whether the ice machine will be turned on or off. When you press the OK button, the ice machine icon lights continuously and the Indicator continues to flash during this process. If you do not press any button after 20 seconds, the icon and the indicator remains on. Thus, the ice machine is switched off. In order to switch on the ice machine again, hover over the icon and the indicator; thus, both the ice machine off icon and the indicator will start flashing. If you do not press any button within 20 seconds, the icon and the indicator will go off and thus the ice machine will be switched on again.

Indicates whether the icematic is

C C

23. Eco fuzzy function icon

Press the FN key (until it reaches the letter e icon and the lower line) to activate the eco fuzzy. When you hover over the eco fuzzy icon and the eco fuzzy function indicator, they start flashing. Thus, you can understand whether the eco fuzzy function will be activated or deactivated. When you press the OK button, the eco fuzzy function icon lights continuously and the Indicator continues to flash during this process. If you do not press any button after 20 seconds, the icon and the indicator remains on. Thus, the eco fuzzy function is activated. In order to cancel the eco fuzzy function, hover over the icon and the indicator again and press the OK key. Thus, both the eco fuzzy function icon and the indicator will start flashing. If you do not press any button within 20 seconds, the icon and the indicator will go off and the eco fuzzy function will be cancelled.

on or off.

Water flow from water tank will stop when this function is selected. However, ice made previously can be taken from the icematic.

Refrigerator / User Manual

Operating the product

24. Vacation function icon

Press the FN key (until it reaches the umbrella icon and the lower line) to activate the vacation function. When you hover over the vacation function icon and the vacation function indicator, they start flashing. Thus, you can understand whether the vacation function will be activated or deactivated. When you press the OK button, the vacation function icon lights continuously and thus the Vacation function is activated. The Indicator continues to flash during this process. Press the OK key to cancel the vacation function. Thus, both the vacation function icon and the indicator will start flashing and the vacation function will be cancelled.

25. Joker fridge icon

When you select the joker fridge icon using the FN button and press the OK key, the joker cabin turns into a fridge cabin and operates as a cooler.

26. Celsius indicator

It is a Celsius indicator. When the Celsius indication is activated, the temperature set values are shown in Celsius and the relevant icon turns on.

27. Set decreasing function

Select the relevant cabin with the select button; the cabin icon representing the relevant cabin will start to flash. If you press the set decreasing button during this process, the set value gets decreased. If you keep pressing it in a loop, the set value returns to the beginning.

28. Temperature change cabin icon

Indicates the cabin whose temperature is to be changed. When the temperature change cabin icon starts flashing, it is understood that the relevant cabin has been selected.

29. Temperature change cabin icon

Indicates the cabin whose temperature is to be changed. When the temperature change cabin icon starts flashing, it is understood that the relevant cabin has been selected.

30. Key lock

Press key lock button simultaneously for 3 seconds. Key lock symbol

will light up and key lock mode will be activated. Buttons will not function if the Key lock mode is

25 / 37 EN

active. Press key lock button simultaneously for 3 seconds again. Key lock symbol will turn off and the key lock mode will be exited.

Press the key lock button if you want to prevent changing of the temperature setting of the refrigerator.

31.Select button

Use this button to select the cabin whose temperature you want to change. Switch between the cabins by pressing this button. The selected cabin can be understood from the cabin icons (7,17,18,20,28,29). Whichever cabin icon is flashing, the cabin, whose temperature set value you want to change, is selected. Then, you can change the set value by pressing the cabin set value decreasing button (27) and the cabin set value increasing button (19). If you do not press the select button for 20 seconds, the cabin icons will go off. You need to press this key to select a cabin again.

32. Alarm off warning

In case of power failure/high temperature alarm, after checking the foods in the freezer compartment, press the alarm off button to clear the warning.

33. Quick cooling function button

The button has two functions. To activate or deactivate the quick cool function, press it briefly. Quick Cool indicator will turn off and the product will return to its normal settings.

Use quick cooling function when you want to quickly cool the food placed

in the fridge compartment. If you want to cool large amounts of fresh food, activate this function before putting the food into the product.

If you do not cancel it, quick cooling will cancel itself automatically after 8 hours at the most or when the fridge compartment reaches to the required temperature.

Refrigerator / User Manual

Operating the product

If you press the quick cooling button repeatedly with short intervals, the

C C

34. 1 Joker temperature indicator

Temperature set values of the joker cabin are displayed.

34. 2 Wine cooler compartment tempature

indicator

Tempature set values of the winecabin are displayed.

electronic circuit protection will be activated and the compressor will not start up immediately.

This function is not recalled when power restores after a power failure.

5.3 Dual cooling system

Your refrigerator is equipped with two separate cooling systems to cool the fresh food compartment and freezer compartment.Thus, air and odour in the fresh food compartment and frozen food compartment do not get mixed. Thanks to these two separate cooling systems, cooling speed is much higher then other refrigerators. Also additional power saving is provided since the defrosting is performed individually.

5.4 Freezing fresh food

•Wrapthefoodorplacetheminacovered

container before putting them in the refrigerator.

•Hotfoodandbeveragesmustcooldowntothe

room temperature before putting them in the refrigerator.

26 /37 EN

Refrigerator / User Manual

Operating the product

•Thefoodthatyouwanttofreezemustbefresh

and in good quality.

•Dividedthefoodintoportionsaccordingtoyour

family’s daily or meal based consumption needs.

•Packthefoodinanairtightmannertoprevent

them from drying even if they are going to be stored for a short time.

•Materialstobeusedforpackagingmustbe

tear-proof and resistant to cold, humidity, odour, oils and acids and they must also be airtight. Moreover, they must be well closed and they must be made from easy-to-use materials that are suitable for deep-freezers.

•Frozenfoodmustbeusedimmediatelyafter

they are thawed and they should never be refrozen.

•Donotfreezetoolargequantitiesoffoodatone

time. The quality of the food is best preserved when it is frozen right through to the core as quickly as possible.

•Placingwarmfoodintothefreezercompartment

causes the cooling system to operate continuously until the food is frozen solid.

5.5 Recommendations for preserving the frozen food

•Frozenfoodthatyouhavepurchasedshould

be stored in accordance with the frozen food manufacturer’s instructions for a ( 4 star) frozen food storage compartment.

•Notethefollowingtoensurethatthehighquality

achieved by the frozen food manufacturer and the food retailer is maintained:

1. Put packets in the freezer as quickly as possible

after purchase.

2. Make sure that contents of the package are

labelled and dated.

3. Check whether the “Use By” and “Best Before”

dates on the packaging are exceed or not.

5.6 Placing the food

Freezer compartment shelves

Egg holder Egg

Fridge compartment shelves

Fridge compartment door shelves

Crisper Vegetables and fruits Fresh zone

compartment

Various frozen food such as meat, fish, ice cream, vegetables and etc.

Food in pans, covered plates and closed containers

Small and packaged food or beverage (such as milk, fruit juice, beer and etc.)

Delicatessen products (cheese, butter, salami and etc.)

5.7 Deep-freeze information

Food must be frozen as rapidly as possible when they are put in a refrigerator in order to keep them in good quality. You can keep the freshness of food for many months (at -18°C / 0°F or lower temperatures in the deep freeze).

Divided the food into portions according to your family’s daily or meal based

27 / 37 EN

consumption needs.

Refrigerator / User Manual

Operating the product

Freezer

Compartment

Setting

-18°C / 0°F 4°C / 39°F This is the normal recommended setting.

-20°C / -4°F 3°C / 37°F

Quick Freeze 4°C / 39°F

-24°C / -12°F 2°C / 35°F

-18°C / 0°F or colder

Recommended Using Temparature: FF: 4°C / 39°F Frz : -18°C / 0°F

Pack the food in an airtight manner to prevent them from drying even if they are

•Materialsnecessaryforpackaging:

•Coldresistantadhesivetape

•Selfadhesivelabel

•Rubberrings

•Pen

going to be stored for a short time.

Fridge

Compartment

Setting

Quick Fridge

Explanations

These settings are recommended when the ambient temperature exceeds 30°C/86°F.

Use when you wish to freeze your food in a short time. Your refrigerator will return to its previous mode when the process is over.

Use these settings if you think that your fridge compartment is not cold enough because of the hot ambient conditions or frequent opening and closing of the door.

Use this function when you place too much into the fridge compartment or when you need to cool your food quickly. It is recommended that you activate Quick Fridge function 4-8 hours before placing the food.

Materials to be used for packaging the foodstuff must be tear-proof and resistant to cold, humidity, odour, oils and acids. Foods to be frozen should not be allowed to come in contact with the previously frozen items to prevent them from getting thawed partially.

Frozen food must be used immediately after they are thawed and they should

never be re-frozen.

28 /37 EN

Refrigerator / User Manual

Operating the product

5.8 Removing door shelves

You can remove the door shelves to clean them. Push the desired shelf up to remove it. Do not remove the door shelf when there is food in it. First empty the materials inside in.

5.9 Moving door rack

*optional

Moving door rack can be fixed in 3 different positions.

In order to move the rack, push the buttons on the side evenly. Rack will be movable.

Move the rack up or down. When the rack is in the position that you want,

release the buttons. Rack will be fixed again in the position where you have released the buttons.

5.10 Glass shelves

You can remove the glass shelves to clean them. Be careful when removing the shelves since they are heavy.

5.11 Chiller compartment

(in some models)

Chiller compartments allow you to prepare the food for freezing. You can also use these compartments to store your food at a temperature a few degrees below the fridge compartment. You can increase the inner volume of your refrigerator by removing any of the chiller compartments:

1. Pull the compartment towards yourself until it

stops.

2. Lift the compartment about 1 cm up and pull

towards yourself to remove it from its seating.

29 / 37 EN

Refrigerator / User Manual

+ 87 hidden pages