Quick Guide
Operation of the product
Read “Safety Instructions” section first!
1. On-Off / Program Selection knob
2. Rinse aid ( ) indicator
3. Low salt ( ) warning indicator
Half load indicator
4.
5. Delay indicator
6.
Child Lock Indicator
7. On/Off Control light
8. Program Monitoring Indicator
a) Washing Indicator
b) Drying Indicator
c) Program Ended Indicator
9. Start / Hold / Cancel key
10. Delay function key /
Half Load function
11.
Tablet detergent indicator
12.
Child Lock Key 3 sec
Tablet detergent function
/
1
2 3 4 5 6 7
a
b
8
c
9101112
3 sec
Auxiliary functions
Washing programmes of your dishwasher
are designed to obtain the best cleaning
effect, considering the type of the soil,
soiling degree and properties of the dishes
to be washed.
Auxiliary functions are provided in order to
enable you to save time, water and energy
and to perform a more comfortable washing
with conditions specific to you.
Auxiliary functions may cause changes
in the programme duration.
Eco *** Intensive Clean&Shine Quick&Shine Mini
50 ºC 70 ºC 65 ºC 60 ºC 35 ºC
Suitable for washing
dishes with normal
amount of soil. It is
the most efficient
program in terms of
combined power and
water consumption.
This is used for
assessing the
compliance with EU's
eco-design directive.
Suitable for heavily
soiled dishes, pots
and pans.
Daily washing
programme for
normally soiled
dishes.
Daily washing
programme for
normally soiled
dishes in the fastest
way.
Suitable for lightly
soiled daily dishes
that are scraped or
pre-cleaned.
Medium High Medium Medium Low
+++- -
+++++
++++-
205 120 120 58 30
12,9 17,6 16,2 11,8 11,8
0,92* / 0,937** 1,65 1,38 1,20 0,80
Loading Capacity: 13
Degree of Soiling
Energy (kWh)
Prewash
Wash
Dry
Duration (min)
Water (I)
Programme Data and Average Consumption Values Table
* : EN 60436:2016 ** : EN 60436:2020 The consumption values shown in the table were determined under standard conditions. Differences may therefore occur under practical conditions.
*** Reference programme for testing institutes. The tests in accordance with EN 50242/60436 must be carried out with a full water softener salt dispenser and a full rinse aid reservoir, and
using the test programme. The values given for programmes other than Eco 50°C programme are indicative only.
Programme name
Cleaning temperature
Programme Table
Quick Guide
Adjusting the water softening system
Washing, rinsing and drying performance of your dishwasher will improve when the water
softening system is adjusted correctly.
To adjust the system, first learn the water hardness in your region and adjust as indicated
below.
• Unpack the test strip.
• Open the tap and let the water flow for approx. 1
minute.
• Dip in the test strip into the water for 1 second.
• Take out the strip from the water and shake it.
• Wait for 1 minute.
• Make the necessary adjustment according to the test
strip.
After the determination of the water hardness:
While the Program Selection Knob is “Off”, press and hold the Start / Pause / Cancel key
and rotate the Program Selection Knob one step clockwise and keep the Start / Pause /
Cancel key pressed for 3 seconds; the machine shall switch to regeneration setting mode
after this period.
2. The regeneration level in the memory is illuminated for 5 seconds when you enter the
regeneration setting mode.
3. For setting a new Water Hardness Level, bring the Program Selection Knob to the
proper position for the hardness level of your mains water. (See Water Hardness Level
Setting Table)
4. Press the Start / Pause / Cancel key to record the selected setting in the memory.
5. Bring the Program selection knob to “Off” position.
Level 0
Level 1
Level 2
Level 3
Level 4
Level 5
1
2
5
3
4
Water hardness level setting table
Hardness
Level
English
Hardness °dE
German
Hardness °dH
French
Hardness °dF
Level of program
selection knob *
Water Hardness Level Indicator
0. Level
1. Level
2. Level
3. Level
4. Level
5. Level
0-5 0-4 0-8 1
6-9 5-7 9-13 1
10-15 8-12 14-22 2
16-19 13-15 23-27 3
20-24 16-19 28-34 4
25-62 20-50 35-90 5
The Washing light on the panel
illuminates.
The Drying light on the panel
illuminates.
The End light on the panel
illuminates.
The Washing, Drying and End lights
on the panel illuminate.
The Washing, Drying and End lights
on the panel ashes with intervals of
1 second.
After detecting the water hardness:
• If the hardness level of the water that you use is above 50°dH or if you are using well
water, than it is recommended to use filter and water purification devices.
• If the hardness level of the water that you use is below 7°dH, there is no need to use
salt in your dishwasher. In this case, the Salt Indicator light on the control panel of your
dishwasher will light continuously.
• If the water hardness is set to level 1, the Salt Indicator will light continuously although
it is not necessary to use salt. If you use salt under this condition, salt will not be
consumed and the lamp will not illuminate.
When moving, you will need to set the water hardness level of your dishwasher again
according to the information above, depending on the water hardness of the place you
have moved to. If the water hardness level of your machine is adjusted previously, your
machine will display the most recent hardness level adjustment.
15 8824 0100-AA_BEKO_A6_EN/ 28-08-20.(9:13)
Loading...