Beko DV 1562 X User manual [EN]

Dryer		DV 1562 X
User manual

2960310117_KM/2808 14.1900

Read this manual prior to initial operation of the product!

Dear Customer,

We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results.

We advise you to read through this manual carefully before using your product and keep it for future reference.

This User Manual will

•Help you use your machine in a fast and safe way.

•Read the User Manual before installing and starting your product.

•In particular, follow the instructions related to safety.

•Keep this User Manual within easy reach for future reference.

•Please read all additional documents supplied with your product. Remember that this User Manual is also applicable for several other models.

Explanation of symbols

Throughout this User Manual the following symbols are used:

A Important safety information. Warning for hazardous situations with regard to life and property.

B

C

Caution; Warning for supply voltage.

Caution; Warning for fire hazard.

Caution; Warning for hot surfaces.

Read the instructions.

Useful information. Important information or useful hints about usage.

TABLE OF CONTENTS
1 Your Dryer	4
Overview..............................................	4
2 Important Safety
Instructions	5
3 Installation	7
Appropriate installation location............	7
Under Counter Installation....................	7
Use on a washing machine..................	7
Adjusting the feet.................................	7
Ventilation hose and connection
(for products equipped with an
outlet vent)...........................................	7

Connection to a water drain (for products equipped with a condenser ).8

Electrical connection............................	9
Destroying the packaging material........	9
Disposing of the old machine...............	9
Technical Specifications.......................	9
4 Initial preparations for
drying	10
Garments suitable for drying in the
machine.............................................	10
Garments unsuitable for drying in
the machine.......................................	10
Preparing clothes to be dried.............	10
Correct load capacity.........................	10
Loading door......................................	11
5 Selecting a Programme
and OperatingYour Machine	12
Control panel......................................	12
Turning the machine on......................	12
Programme selection.........................	12
Main programmes..............................	13
Special programmes .........................	13
Programme selection and
consumption table.............................	14
Auxiliary function................................	15
Warning indicators.............................	15
Starting the Programme.....................	15
Progress of programme......................	15

Changing the programme after
the programme has started................	15
Adding/removing laundry in
standby mode....................................	15
Child-proof lock..................................	16
Ending the programe through
canceling...........................................	16
End of programme.............................	16
6 Quick instructions for
daily use	17
7 Maintenance and cleaning	18
Cover filter .........................................	18
Sensor (models equipped
with a sensor).....................................	18
Water tank (Products equipped
with a condenser);..............................	18
For the condenser (products
equipped with a condenser);..............	19
8 Solution suggestions for
problems	20

3 - EN

1	Your Dryer

Overview

5

1

2

3

4

1- Type label

4- Adjustable Feet

2- Control Panel

5- Power Cord

3- Lint filter

Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly. Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the appliance, values may vary.

4 - EN

2 Important Safety Instructions

A WARNING:To reduce the risk of fire, electric shock, or injury to

persons when using your appliance, follow basic precautions including the following:

•Read all instructions before using the appliance. Otherwise, there may be the risk of personal injury or material damage. Moreover, any warranty and reliability commitment will become void.

AThis product has been designed for home use only.

•Your machine can be operated at temperatures between +5°C and +35°C.

•The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer.

•Do not install or store this appliance where it will be exposed to the weather.

•Do not tamper with controls.

•Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

•Unplug the machine when it is not in use.

•Never wash down the appliance with water! There is the risk of electric shock!

•Never touch the plug with wet hands.

•Never pull from the cable to unplug the machine.

•Do not operate the machine if the power cord or plug is damaged.

•Never attempt to repair the machine yourself.

•For malfunctions that cannot be solved by information in the operating manual: Turn off and unplug the appliance and call an authorized service agent.

•This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

B WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service represantative or personnel if you are in doubt as to whether the appliance is properly grounded.

•Power cord plug must be within easy reach after installation.

•To reduce the risk of fire or electrical shock, do not use extension cords, multi-plugs or an adapter to connect the dryer to electrical mains.

•Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

•The appliance must not be operated unless it is repaired! There is the risk of electric shock!

•Ventilation openings in the base must not be obstructed by a carpet, etc.

•Exhaust air must not be discharged into a flue, which is used for exhausting fumes from appliances burning gas or other fuels.

•Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.

•Do not dry articles that have been previously cleaned in, washed in, soaked in or spotted with petrol/ gasoline, dry-cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or

5 - EN

explode.

•Do not use the tumble dryer if industrial chemicals have been used for cleaning.

•Do not dry unwashed items in the tumble dryer.

•Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.

•Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.

•Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

•The appliance may only be used for drying of textiles that are marked accordingly.

•Undergarments that contain metal reinforcements should not be placed in a tumble dryer. Damage to the tumble dryer can result if metal reinforcements come loose during drying.

•Check all garments for forgotten lighters, coins, metal pieces, needles, etc. before loading.

•Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.

•The final part of a tumble dryer cycle occurs without heat (cool-down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.

A WARNING: Never stop the tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

•Do not reach into the appliance if the drum is moving.

•Do not allow children to play on or in the appliance.

•Young children should be supervised to ensure that they do not play with the

appliance.

•Before the appliance is removed from service or discarded, remove the door to the drying compartment.

•Close the loading door when you leave the area where the machine is located.

•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•Clean lint screen before or after each load.

•Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

•The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

•Never use the dryer without the lint filter.

6 - EN

2Installation

Refer to the nearest Authorised Service Agent for installation of your product. CPreparation of location and electrical installation for the product is under

customer’s responsibility. BInstallation and electrical connections

must be carried out by a qualified personnel.

APrior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks for your safety.

Appropriate installation location

• Install the product in an environment which has no risk of freezing and is in a stable and level position.

• Operate your product in a well ventilated, dust-free environment.

• Do not block the air ducts in front of and under the product with materials such as long pile rugs and wooden bands.

• Do not place your product on a long pile rug or on similar surfaces.

• Do not install the product behind a door with a lock, sliding door or a hinged door which can strike the product.

• Once the product is installed, it should stay at the same place where its connections have been made. When installing the product, make sure

that the rear wall of it does not touch anywhere (tap, socket, etc.) and also pay attention to install the product at a place where it will stay permanently.

BDo not place the product on top of the power cable.

•Keep at least 1.5 cm distance to walls of other furniture.

Under counter installation

•A special part (Part no: 295 970 0100) replacing the top trim must be provided and installed by the Authorised Service Agent in order to use the machine under a counter or in a cupboard. It should never be operated without the top trim.

•Leave at least 3 cm of space between

the side and rear walls of the product and the walls of the counter/cupboard when installing your product under a counter or in a cupboard.

Mounting over a washing machine

•A fitting device should be used between the two machines when installing above a washing machine. The bracket (Part no. 296 280 0100 white/296 280 0200 grey) must be installed by the Authorised Service Agent.

•Place the product on a firm floor. If it will be placed on top of a washing machine, the approximate weight of both machines may reach 180 kg

when they are full. Therefore, the floor must be capable of carrying the load on it!

Ventilation hose and connection (for products equipped with an outlet vent)

Ventilation hose allows exhaust air from inside the machine

Vented dryer has 1 air outlet.

Stainless sheet metal or aluminum pipes can be used instead of a hose. The pipe diameter should be minimum 10 cm.

Maximum hose and pipe lengths are given in the table below.

	Hose	Pipe
Maximum length	4 m	5 m
1 elbow 45°	-1.0 m	-0.3 m
1 elbow 90°	-1.8 m	-0.6 m
1 elbow 90° short		-2.7 m
1 wall passage	-2.0 m	-2.0 m

CEach elbow and other passages should be subtracted from the maximum length stated above.

To connect a ventilation hose;

1. Connect the air outlet hose to the hose spacer piece by turning it counterclockwise.

2. Make the hose passages as shown below.

CExhaust of humid air from the dryer into the room is inconvenient. It may

7 - EN

damage the walls and furniture in the room.

CThe ventilation hose can be routed outdoors via a window or it can be connected to the air outlet in the bathroom.

CAir outlet hose must be routed directly to the outdoors. There must be a limited number of elbows as not to hinder ventilation.

CTo prevent water accumulation in the hose, make sure that it is not folded on the floor.

BThe ventilation hose should not be connected to the chimney of a stove or a fireplace.

BDo not operate your product at the same time with heaters such as a coal or gas stove. Airflow may cause the chimney to flare up.

Adjusting feet

In order to ensure that your product operates more silently and vibrationfree, it must stand level and balanced on its feet. Front feet of your product can be adjusted. Balance the machine by adjusting the feet.

1. Loosen the feet by hand.

2. Adjust the feet until the product stands level and firmly on the floor.

CDo not use any tools to loosen the adjustable feet, otherwise, they can be damaged.

CNever remove the adjustable feet from their housings.

CYou may supply 2 plastic pieces from an Authorized Service with

2951620100 part number. These parts prevent your machine from slipping when the machine locates on wet and slippery surfaces. You may assemble mentioned parts to the front adjustable feet by fitting and pressing them to snap into ground of feet.

Electrical connection

Connect the machine to an earthed outlet protected by a fuse of suitable capacity. Important:

•Connection should comply with national regulations.

•Power cord plug must be within easy reach after installation.

•The voltage and the allowed fuse protection are specified in the section “Technical Specifications”.

•The stated voltage must match with your mains voltage.

•Connection via extension cords or multi-plugs should not be made.

•The main fuse and switches must have a contact distance of minimum 3 mm.

BA damaged power cable must be replaced by a qualified electrician.

BThe appliance must not be operated unless it is repaired! There is the risk of electric shock!

First use

•To have the product ready for operation before calling the authorised service agent, make sure that its location and power supply installations are appropriate. If they are not, call

a qualified electrician to have any necessary arrangements carried out.

•Make sure that the power connections of the product are in accordance

with the instructions given in relevant chapters of this manual.

Disposing of packaging material

Packaging materials are dangerous to children. Keep packaging materials in a safe place out of reach of children.

Packaging materials of your product are

8 - EN

manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste.

Transportation of the machine

1.Unplug the machine from the mains.

2.Remove the water drain (if any) and chimney connections.

3.Drain water remained in the machine completely before transportation.

Disposing of the old machine

Dispose of your old machine in an environmentally friendly manner.

Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your machine.

Before disposing of your old machine, cut off the power cable plug and make the loading door lock unusable to avoid dangerous conditions to children.

Technical Specifications

EN

Height (adjustable)	85.0 cm
Width	59.5 cm
Depth	54 cm
Capacity (max.)	6 kg
Weight (net)	31 kg
Voltage
Rated power input	See type label
Model code

Type label is located behind the loading door.

This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose.

Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on

Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

9 - EN

4 Initial preparations for drying

Garments suitable for drying in the machine

Always follow the advice on the garment labels. With this dryer, dry only the laundry having a label stating that they are suitable for drying in a dryer by selecting the appropriate programme.

A B C D

Low

l n m

o p q

Garments unsuitable for drying in the machine

•Laundry items and attachments made of or contain metal, hard plastic and similar materials, such as belt buckles, jeans, bra wires, buttons and similar accessories will damage your machine and may cause breakdown. So do not place such items in the tumble dryer. If you are in doubt, please call Customer Help Line.

•Do not dry items such as woolen, silk garments and nylon stockings, delicate embroidered fabrics, garments with metal accessories and items such as sleeping bags in the machine.

•Garments made of delicate and valuable fabrics as well as lace curtains can be creased. Do not dry these in your machine!

•Do not dry items made of hermetic fibers such as pillows and quilts in the drying machine.

•Garments made of foam or rubber may be deformed.

•Do not dry clothes containing rubber in the machine.

•Do not dry clothes exposed to petroleum, oil, combustible or explosive agents in the machine even if they are washed beforehand.

•Overly wet laundry or laundry with dripping water must not be put into the machine.

Preparing clothes to be dried

•All laundry must be spun at the highest possible spin speed your washing machine allows for the textile type.

•Laundry may be tangled after washing. Separate your laundry before placing them into your dryer.

•Sort your laundry according to their types and thicknesses. Dry the same type of laundry together. E.g..: fine kitchen towels and table cloths dry faster than the thick bath towels.

Correct load capacity

A Please consider the information in the “Programme Selection Table”. Always

start the programme in accordance with the maximum load capacity.

C Adding laundry to the machine more than the level shown in the figure is not recommended.. Drying performance will degrade when the machine is overloaded. Furthermore, your machine and your clothes might be damaged.

C Place your garments into the drum loosely so that they will not get tangled..

C Large pieces (E.g.: bed sheets, quilt

10 - EN

covers, large tablecloths) may bunchup. Stop the machine 1-2 times during drying process to separate bunched-up laundry.

Following weights are given as examples.

	Home articles	Approximate
		weights (gr)
	Cotton quit covers (double)	1500
	Cotton quit covers (single)	1000
	Bed sheets (double)	500
	Bed sheets (single)	350
	Large tablecloths	700
	Small tablecloths	250
	Tea napkins	100
	Bath towels	700
	Hand towels	350
	Garments	Approximate
		weights (gr)
	Blouses	150
	Cotton shirts	300
	Shirt	200
	Cotton dresses	500
	Dresses	350
	Jeans	700
	Handkerchiefs	100
	T-Shirts	125

Loading door

•Open the loading door.

•Place laundry items loosely into the machine.

•Push the loading door to close. Ensure that no items are caught in the door.

11 - EN

5 Selecting a Programme and OperatingYour Machine

Control panel

Figure 2

6	5	4		1

3

2

1.On/Off button

2.Programme selection knob

3.Start/Pause/Cancel button

4.Cancel Audio Warning

5.Programme follow-up indicator

Turning the machine on

Prepare machine for programme selection by pressing the “On/Off” button. C Pressing the “On/Off” button does not

necessarily mean that the programme has started. Press “Start/Pause/ Cancel” button of the machine to start the programe.

Programme selection

Decide the appropriate programme from the table below which includes drying temperature in degrees. Select the desired programme with the programme selection button.

6.Filter cleaning warning LED

7.Water tank full warning LED *

8.Time Delay Button *

* It may change according to the specifications of your dryer

	Dry at high temperature
	only for cotton laundry.
	Thick and multi layered
Extra dry	laundry (E.g.: towels,
	linens, jeans) are dried in
	a way that they do not
	require ironing before
	placing in the wardrobe.
	Normal laundry (E.g.:
	tablecloths, underwear)
Ready to Wear	are dried in a way that
	they do not require
	ironing before placing in
	the drawers.
	Normal laundry (E.g.,
Ready to Iron	Shirts, dresses) are dried
	ready to be ironed.

12 - EN