Beko BKL15LW03 Schematic

ULC TARGET SPECS
Ultra low cost 15"
(15" - 19" 4:3)
SCALER MST7610 (Maria) Mstar or Renesas Scaler DISPLAY
Type TFT Aspect ratio 4:3 Brightness 250 cd, 180 cd
Diagonal screen size 15 inch / 38 cm Panel resolution 1024*768 Viewing angle (H / V) 160/155
Response time (typical) 12 CONNECTIONS
Antenna (IEC 169-2, Female)
Scart 1 full default S-video In (DIN) NO Video In (RCA) 1 Audio In (2 RCA) 1 Video Out (RCA) NO
1
Audio Out (2 RCA) NO
Progressive YPbPr In (3 RCA)
Audio In for progressive input (2 RCA)
DVI NO HDMI NO
PC Audio (L, R) PC input via stereo jack available (OPT) Subwoofer NO
D-Sub 15 D-SUB 15 available (OPT) SPDIF Coaxial NO SPDIF Optic NO RS232 NO Headphone NO
ADD ON MODULE CONNECTION OPTIONS Front\Side AV NO
VIDEO & GRAPHICS IN\OUT
CVBS In 1 through SCART, 1 through RCA RF In 1 through tuner Y\C In No
No
No
RGB+FB In-Video 1 through SCART1 RGB+HS, VS In -
Graphics YPbPr In
(Progressive) DVI In NO
HDMI In NO
CVBS Out 1 through SCART1 RGB, FB Out no
HDMI out no
AUDIO IN\OUT Stereo L, R In 1 mono through RCA, 2 MONO through SCARTS
AV Stereo IN 1 stereo through RCA, 1 stereo through SCARTS, 1 PC audio in
Stereo L, R Out NO Subwoofer Out NO
S\PDIF In NO S\PDIF Out NO Subwoofer Out NO Subwoofer Output
Power Audio Output Power 1x3W
1 through DSUB-15
NO
NO
Number of speakers 1 Speaker Placement Inside the cabinet
ANALOG FRONT END Type Receiving System
Input Freq. Range (MHz)
Tune down to 45,25MHz Tune up to 863,25MHz
Input Connector IEC 169-2, Female Aerial Input
Impedance Signal Level NO Tuning System FST Tuning Control PLL Antenna Loop
Through RF Modulator NO Channel Bandwidth 6\7\8 MHz Switchable FE Control I2C
YES
75 Ohm (unbalanced)
NO
Conventional tuner
+IF Demodulator
VHF (48,25-463,25MHz)
UHF (471,25-855,25MHz)
TV system PAL/SECAM BG/DK/I From Service Menu
Video Playback NTSC, PAL, SECAM VIDEO & GRAPHICS
PROCESSING
De-multiplexing
ADC (Video) Resolution 8 bit Chroma Decoding Standart PAL, SECAM, NTSC Comb Filter ­Color Temparature Yes LTI, CTI Filters Yes
Data Rate >= PID Filters >= Section Filters >=
Sync On Green (SOG) support on graphics
De-Interlacer 2D-DI PAT No Gamma Correction Yes PIP\PAP\ No OSD font based Saturation Yes Contrast Yes Tint Yes Noise reduction 2D
AUDIO PROCESSING Virtual Dolby/SRS
WOW Subwoofer NO Effect\Spatial NO Dynamic Bass NO VBI DATA
PROCESSING Teletext Teletext 1.5 Fast text optional Top text optional page 8 WSS YES VPS\PDC\CNI YES Closed Caption NO SUPPORTED
OUTPUTS FOR DISPLAYS
Single TTL support YES Dual TTL support NO Single 10-bit TTL
support Dual 10-bit TTL
support Single LVDS support
(8-bit) Dual LVDS support
(8-bit) Single LVDS support
(10-bit)
YES
No
NO
NO
YES
YES
NO
Dual LVDS support (10-bit)
Timing Control Support
Supported Output Upto WXGA+ at 60Hz (1440x900)
APPLICATIONS Menu System Beko GUI / Beko OSD Remote Control Supported Menu
Languages Picture Formats
(Auto, 4:3, 16:9, 14:9, Zoom, LetterBox, Subtitle)
WSS (Wide Screen Signalling)
Channel skip time
ATS (Automatic Tuning System)
Black Line Detection no Manual Search Channel search
NO
NO
tbd
for 4:3 models 16:10 ,4:3 and Auto ,16:9 models have all
YES
Frequency Search time tbd
Beko RC
<1 sec
AFC (Auto Frequency Correction)
Number of Program Storage
No Ident Timer YES Picture Freeze no Equalizer NO
AVL (Automatic Volume Level)
Optic sensor no Sound Status
Memory Picture Status
Memory Zapping\Swap Swap Child Lock NO
Program Lock no Picture Format
Switching Through Scart (Pin 8)
Auto RGB Detect Through Scart (Pin
16) DDC Support YES
Timer On\Off or Sleep Sleep
YES
100 99
NO
no
YES
YES
YES
Picture Smart Modes YES
Sound Smart Modes no Scart2 Out Selectable no S-Video Input
Through Scart2
Wake Up in PC
POWER SUPPLY PSU Type LIPS Input Range 100V-240V, 50, 60Hz Groundless AC Plug YES (EXCEPT UK) St-By Power
Consumption 12V ext power in NO REGULATIONS
EMC
SAFETY EN60065 CABINET
Keyboard
LED
no
Stby to On in PC mode when last watched is PC
Stby to On automatically when PC signal is available
<2W
On\Off no Volume Up no Volume Down no Program Up no Program Down no Menu no Source no Single color
/Single Intensity Single Color
/Double Intensity Multi color no On Timer Led NO
YES
YES
EN55020 EN55013
EN55022 (with PC)
no
yes
SEQUENCE OF ADJUSTMENT AND CHECKING
SERVĐS MENU OPTIONS 1
OPTIONS 1 FAST TEXT: ON: Fast Text features ON, OFF: Fast Text feature OFF.
NOTE : Unless customer special choice, select it ON. TOP TEXT : ON: Top Text features ON, OFF: Top Text feature OFF. NOTE : Unless customer special choice, select it OFF. TEXT LANGUAGE : AUTO; automatically selects the TEXT language NOTE : Unless the customer demands; it will be set as AUTO WEST : English,French, German, Turkish, Spanish, Italian, Finnish,
EAST : Lehçe,Fransızca,Macarca,Çekçe,Almanca,Slovence,Đtalyanca,Romence CYRILLIC : Đngilizce,Rusça,Almanca,Çekçe,Estonyaca,Ukraynaca,Letonyaca ARABIC : West+Arapça ; FARSI : West+Farsça ; HEBREW : West+Đbranice STANDBY RECALL: ON : TV is switched on with previous settings. OFF : TV is switched on in StdBy
NOTE: Unless customer special choice, select it OFF. RECALL LAST AV: ON : Last AV memory mode active
OFF : Last AV memory mode active
NOTE: Unless customer special choice, select it OFF. FACTORY RESET : ON : Back to the Factory out adjustments option is active. OFF : Back
to the Factory out adjustments option is not active. Do not perform any adjustment unless indicated.
COMB FILTER : ON: Comb Filter features ON, OFF: Comb Filter features OFF. NOTE : Unless customer special choice, select it ON.
OPTIONS 2 MONITOR FEATURES : ON: Monitor features ON, OFF: Monitor features OFF.
NOTE : Unless customer special choice, select it OFF. HOTEL MODE : ON : Hotel TV mode is on ; OFF : Hotel TV mode is OFF. NOTE : If no customer demand it will be set as OFF HOTEL MODE VOL : It adjusts the volume level on Hotel Mode. DIMMING : It automatically comes adjusted according to the panel of the TV. Do not
perform any adjustment unless indicated.
FACTORY MODE : ON :Factory mode on ; OFF : Factory mode off RESET EEPROM : Do not perform any adjustment unless indicated. PLUG AND PLAY : Demo mode. Set it ON after all settings.
SERVICE MODE OPTIONS 2
SOURCE OPTIONS PC : ON : The feature is active, OFF : The feature is passive
TV : ON : The feature is active, OFF : The feature is passive AV : ON : AV automatic switching control active
OFF : AV automatic switching control passive
SCART 1 : ON : SCART 1 is available, OFF : SCART 1 is not available NOTE : Unless customer special choice, select it ON.
TUNING OPTIONS SOUND STANDARD : BG, DK, I, L
NOTE : Unless the product is “L” set it as “BG”. If the product is “Secam L” set it as “L”. AGC VHF 17 AGC UHF 17 AGC LPRIME 17 TUNER TYPE : Used to choose the tuner for the TV . NOTE : ON : Tuner is available, OFF : Tuner is not available ATS : ON: Autoprogramming ON at startup. OFF: Autoprogramming OFF at startup. NOTE : ON : The function is available, OFF : The function is not available AUDIO GAIN : ON : The function is available, OFF : The function is not available NOTE : Unless customer special choice, select it OFF.
ADC CALIBRATION
R GAIN G GAIN B GAIN R OFFSET G OFFSET B OFFSET
NOTE : These values are automatically stored after Factory Reset. No adjustment and checking for these values.
WHITE BALANCE
R GAIN G GAIN B GAIN
NOTE : These values are automatically stored after Factory Reset. No adjustment and checking for these values.
SAFETY PRECAUTIONS
GENERAL GUIDELINES
Always use the manufacturer’s replacement safety
1.
components. The critical safety components marked
with on the schematics diagrams should not be by other substitutes. Other substitute may create the electrical shock , fire or other hazards. Take attention to replace the spacers with the originals. Furthermore where a short circuit has occurred , replace those components that indicate evidence of overheating.
2. After servicing , see that all the protective devices
such as insulation barriers, insulation papers, shields and isolation R-C combinations are correctly installed.
3. When the receiver is not being used for a long time
of period of time , unplug the power cord of the Adaptor from the AC outlet.
Color TFT LCD Module is very sensitive both electrically and physically.Users, therefore, are requested to follow the “Guidance of handling color TFT LCD Module”on the followings.
1 - Be careful not to make scratch on the
polarizer.
Surface of polarizer is soft and can be physically
damaged easily.
Please do not touch, push or rub polarizer surface
with materials over HB hardness.
5 High temperature & high humidity
reduce the life-time.
LCD is not proper to be used at high temperature and high humidity. Please keep specified temperature and humidity condition.
6 - Keep out of Corrosive Gas.
Corrosive gas effect the polarizer and the circuit chemically and cause defects accordingly.
7 - Electrostatic discharge can make
Damage
There are electro-static sensitive components such as CMOS in LCD Module. Please earth human body when handle the LCD.In addition, please do not touch the interface connector pin with bare.
8 - Do not operate for a long time under
the same pattern
Operating LCD for a long time under the same pattern can cause image persistence and can damage it. P lease follow following guidance.
1. Turn the power off when do not use.
2. Change the pattern periodically.
2 - Keep clean the surface.
Please wear rubber glove when touch the surface of LCD screen. Please use soft and anti-static material as cleaner.
3 - Keep out of water.
Water on/in the LCD may cause electrical short or corrosion. Please wipe out dry or water carefully
4 - Prevent swift Temperature &
Humidity change.
Instantaneous temperature and/or humidity change can make dew or ice which cause nonconformance such as malfunction.
.
Arıza tespiti için bazı gerekli transistörlerin bacak gerilimleri
T101 T100 T103
ST-BY ON Pin ST-BY ON Pin ST-BY ON Pin
3,2 0 C 3,1 0 D 0 4,5 C
0 0,6 B 1,5 3,2 G 0,7 0 B 0 0 E 3,2 3,2 S 0 0 E
T104 T105 T106
ST-BY ON Pin ST-BY ON Pin ST-BY ON Pin
0 5,2 C 3,3 1,5 G 11,5 0,4 D
3,2 1,6 B 4,8 4,8 S 1,05 12,11 G
0 0 E 3,25 3,3 D 11,5 12,11 S
T107
ST-BY ON Pin ST-BY ON Pin ST-BY ON Pin
12 0 C 0,3 4,9 C 3,2 3,2 D
0 0,7 B 0 1,9 B 3,8 3,8 G 0 0 E 0 1,3 E 2,4 2,4 S
T108 T112
Arıza tespiti için gerekebilecek referans noktalardaki osiloskop çıktıları:
Önemli NOT: Aşağıdaki osiloskop çıktıları tv de herhangi bir tuner kanalı verili iken
ölçülmüştür. TV nin ayarlarına ve kaynağa göre sinyallerde değişiklikler olabilir.
1)C199 kondansatöründen ölçülen X100 kristali osiloskop çıktısı.
2)C100 kondansatöründen ölçülebilen Y100 kristali osiloskop çıktısı
3)T105 transistörünün Gate inden ölçülebilen PWM2 sinyali
4)R132 dairencinden ölçülebilen 33V_PWM sinyali
5)R128 direncinden ölçülebilen VBLCTR sinayli (tv açıkken)
6)R126 direncindenden ölçülebilen BRIGHTNESS sinyali
7)R138 direncinden ölçülebilen STANDBY sinyali (tv açıkken)
8) R121 direncindenden ölçülebilen VDDCTRL sinyali (tv açıkken)
9) R226 direncinden ölçülebilen LED sinyali (tv standby da iken)
There is sound but not picture
when tv opened. and
backlight is working
Check if LVDS cable is
connected correctly
and undamaged.
Y E S
Check if there is panel
power at 1th and 32th
pins of S102
(3,3 yada 5V)
NO
NO
NO
Reconnect LVDS cable both panel and chassis side. And check if the cable damaged.
Check if there is
panel power at T100
output. And check if
VDD_CTRL signal at
high state.
NO
Panel power signal is lost.
IC100 and surrounding
components may be damaged.
Y E S
Check if the TFT-LCD is working correctly. İt' s T-
CON board or chemical
structure may be
damaged.
N O
YES
Y E S
Check if T100, T101and
surrounding components are
undamaged.
Change TFT-LCD
LVDS data is lost. Change LVDS
cable , check if RP100-RP106
resistors are undamaged. IC100 may
be damaged.
There is sound but not picture
when tv opened. and backlight
is not working
Check if cables and
connectors are placed
correctly on main and
PSU chassis
Y E S
is there 5Volts at first
pin of S110 connector?
(BL_ON/OFF)
Y E S
NO
NO
Place the cables correctly as
seen at cable configration.
Check that if transistor T103 undamaged. And İs the signal VBLCTRL
at low condition?
Y E S
NO
There is no " open backlight "
command. IC100 or its
surrounding components may be
damaged. Check them
is the voltage at 8th pin
of IC304 (on lips modul)
at low condition?
(DIM pin)
N O
Check if T102 transistor
is undamaged and there
is BRIGTNESS signal
control.
YES
NO
Chech if transistor T103 and
connections to S110
undamaged.
IC304 and surrounding components
may be damaged. And check also
IC305 veTR301 components.
if there is no BRIGHTNESS
control, IC100 or its surrounding
component may be damaged.
Y E S
Check if T102 and S110
connector are undamage. DIM
signal must be 0V.
No sound problem
g
is there aproximately
5V dc at S106
connector. Check if
you can see sound
nal on osciloscop.
si
YES
Loudspeaker or it's cables may
be damaged.
N O
is there sound signal at
14th and 17th pins of
IC107 ?
N O
NO
YES
L123-L128 components and
connections may be damaged.
Check if there is sound
input at 20th pin of
IC107.
N O
Check if there is x(MONO)
signal output at 13th pin of
IC108 . There must be
sound signal at 11th pin if
source is tuner.
YES
YES
Check it there is 12V
at 4th pin of IC107
N O
Check if there is
12V_SW at T106
transistor.
YES
YES
Check if IC at mute condition.
(Between R178 ve R188 you
must see bigger than 0,3V.)
Check if IC 501 and surrounding
components are undamaged.
Check 12V_SW connections.
N
N O
Check if STANDBY signal at high state
Check MONO_AUD signal at IC 110.
IC110 or surrounding componenets
may be damaged.
(measure from base of T107). Otherwise
IC100 or surrounding components may be
O
damaged.
Loading...
+ 39 hidden pages