Beijer Electronics EPC GEmbedded PC User Manual

EPC G

User Manual

Embedded PC

Reg 10497/0604

CiS No.: 360.610.0070 V ersion 1/06.04 © Systeme Lauer GmbH & Co. KG

Systeme Lauer GmbH & Co KG Postfach 1465 D-72604 NürtingenGermany

User Manual: EPC G Issued: June, 2004 Author: Jung

Operating instructions, manuals and software are protected by copyright laws. All rights reserved. Copying, duplicating, translating, or converting these materials in whole or in part is prohibited. An exception is made in the case of preparing a backup copy of the software for personal use.

• The manual is subject to change without prior notification.

• We cannot guarantee that the programs and data stored on the disk are free of errors and absolutely correct.

• Since diskettes represent manipulatable data media, all we can guarantee is that there is no physical damage to them. Liability is limited to replacement.

• We welcome suggestions for improvements as well as pointing out errors at any time.

• The agreements also apply to the special appendices to this manual.

Embedded PC

0-2

Microsoft, Windows, Windows NT and the Windows Logo are either registered trademarks or trademarks of Microsoft Corporation in the USA and/or other countries.

Other names designated in this document may be brand names, the use of which by third parties for their own purposes may violate the rights of the proprietors.

Information for Users

Please read this manual before using the product for the first time, and be sure to keep it where you can make use of it later.

Unless where explicitly referred to the versions Economy Unit or Business Unit, the description applies for all units.

Intended audience The manual has been written for users who are familiar with PC systems

and automation technology.

Conventions used in this manual [KEY] Keys the user has to press on the keyboard are

represented in square brackets, e.g. [CTRL] or [DEL].

Courier Screen output is represented in the Courier type font,

e.g. C:\>

Courier Bold User inputs via keyboard are identified

by the Courier Bold type font, e.g. C:\>DIR

Italics

Safety instructions Wherever there may be dangerous faults in the automation equipment,

i.e., where an error would cause significant property damage or injury to persons if it occurred, additional external precautions must be taken or equipment must be set up (for example by using independent limit switches, mechanical disabling locks, etc.). In the event of an error, these measures must ensure or force a safe operating status. Testing and verification of suitability for the purpose intended by the user, or for deployment under usage conditions, are the responsibility of the user. Systeme Lauer accepts no liability for testid.

Pictograms The following pictograms have been used in the manual to identify special

text passages:

Danger!

Potentially hazardous situation.

May result in personal injury.

The names of buttons, menus or other screen elements the user has to select and product names are represented in

italics

Caution!

Potentially hazardous situation.

May result in property damage.

Tips and supplementary information

0-3

Information for Users 0- 3 T able of Contents 0- 4 Company 0-5 Contact 0-6 1 Product Description 1- 1

1.1 Control side ..................................................................... 1-1

1.1.1 EPC G Touch .......................................................... 1-1

1.1.2 EPC G Ke y ............................................................. 1- 1

1.2 Rear side .......................................................................... 1-2

2 Commissioning 2-1

2.1 P ower suppl y................................................................... 2-1

2.2 Grounding diagram......................................................... 2-2

2.3 Installation ....................................................................... 2-2

T T echnical data T-1

T1 Mechanical dimensions ...................................................T-1

T1.1 EPC G 1000 Outer/Mounting dimensions .................T-1

T1.2 EPC G 1000 Unit dimensions...................................T-2

T1.3 EPC G 1200 Outer/Mounting dimensions .................T-3

T1.4 EPC G 1200 Unit dimensions...................................T-4

T1.5 EPC G 1500 Outer/Mounting dimensions .................T-5

T1.6 EPC G 1500 Unit dimensions...................................T-6

T1.7 EPC G 1500 V2A Outer/Mounting dimensions .........T-7

T1.8 EPC G 1500 V2A Unit dimensions ...........................T-8

T1.9 EPC G 1000k Outer/Mounting dimensions ..............T-9

T1.10 EPC G 1000k Unit dimensions...............................T-10

T1.11 EPC G 1200k Outer/Mounting dimensions ............. T-11

T1.12 EPC G 1200k Unit dimensions...............................T-12

T2 Electrical data .................................................................T-13

T3 Ambient conditions........................................................ T-14

T4 Interfaces ........................................................................T-15

T4.1 Compact-FLASH-Slot............................................. T-15

T4.2 VGA/COM Interface ...............................................T-15

T4.3 Ethernet, USB, PS/2 ..............................................T-16

T4.4 Cassette option ......................................................T-16

0-4

Company

Elektronik-Systeme LAUER GmbH & Co . KG

Kelterstraße 59 D-72669 UnterensingenGermany T el. +49 (7022) 9660-0 Fax. + 49 (7022) 9660-274

Our philosophy Systeme LAUER is a reliab le partner who thinks and acts internationally.

From the LCA electronic te xt display and the high-tech PCS control panel to the industrial computer we supply a complete program for

• operation

• monitoring and

• control

Within the AUGUSTA Technologie AG, a group of global companies , Systeme LAUER stands for an almost unlimited product range right up to competent service.

On account of an active cooperation with our customers, our qualified team produces convincing concepts which bring man, machine and interface into line in an efficient wa y. Proximity to our customers – the direct dialog – is the foundation of our success.

0-5

Contact

Support Telephone: +49 (7022) 9660–209

E-mail: support@systeme-lauer.de

In case of support enquiries, please have the serial number of the device ready !

Please access our Download Forum to find current drivers, software, drivers, manuals, … and novelties at

http://forum.systeme-lauer.de/

Sales Telephone: +49 (7022) 9660-0

E-mail: Sales@systeme-lauer.de

In addition, we offer ... training and technical courses in our modern training center, or, if you

prefer, in your company. Ask your sales partner for our current training catalog.

... not only demonstration units, but we also provide specialists who assist you personally when starting your first application.

0-6

1 Product Description1 Product Description

1.1 Control side

1.1.1EPC G T ouch

1 Color TFT -Display

10,4“, 12,1“ or 15“ with Resistiv T ouch

1.1.2EPC G Key

2 Color TFT -Display

10,4“ with Resistiv Touch

3 Color TFT -Display

12,1“ with Resistiv Touch

1-1

1 Product Description

4 Color TFT -Display

15“ with Resistiv Touch

5 Front plate V2A

1.2 Rear side

6 COM 1 / COM 2 7 VGA 8 PS/2 Mouse / PS/2 keyboard 9 USB 1 / 2 aJ LAN 1 / 2 aA Grounding screw aB Po wer supply aC Compact Flash

89aJ

1-2

+ 18 hidden pages