B.E.G. Luxomat LC-plus 280 Service Manual
LUXOMAT® LC-plus 280
1:4
1.
0.5
0.25
Futura Book 24Pt
TEST
COMFORT
Operating and mounting instructions for motion detector LUXOMAT® LC-plus 280
GB
1. Mounting preparations 2. Mounting types
1
1
2
2
1)
Caution: have all work involving the 230 V
mains supply carried out by a qualified electrician! Before starting disconnect the mains!
Please be aware, that the LUXOMAT® LC-plus
280 is not suitable as an intrusion detector,
since it is not equipped with a tamper contact.
2) Socket base corner mounting
Important: The LUXOMAT® LC-plus 280 has
to be mounted in such a way, that the adjusting
elements/rotary regulators are always pointed
downward.
1) Wall mounting
2) Outside corner mountable with plug-in
socket (included)
3. Plug-in socket
1
1
2
2
1) Press here for separation of terminal case
and plug-in socket
2) Mount the plug-in socket with two screws
and the enclosed seal rings on a firm base
(Pay attention to inserting of the connection
cable, see point 4)
4. Inserting of the connection cable
1
2
1) Connection cable from top down
2) Connection cable from below
3) Terminal markings
(Wiring diagrams see point 16)
3
5. Putting into operation / Settings
Self test cycle
After mounting and connecting the 230 VAC supply
voltage, the LED flashed for 1min. to show a self testing
unit. Then the unit is ready for operation and the settings can be made manually or with remote control
(see point 11).
1
2
30s
4
15s
6
8
T
10
12
16
Follow-up time Lux value
7. Sensor head optics
8. Sensitivity adjustment (mounting height 2.50 m) ;
mounting height min. = 2.00 m
(Sensor head justified horizontally, see point 7)
200°
By swinging the sensor head horizontally
(approx. ±45°) and vertically (approx. ±15°)
the detection area can be changed.
10. Mounting place
1 2
1) If possible mount unit on a safe place
(wall or ceiling mount).
1) Range walking across: approx. 16m
2) Range walking towards: approx. 9m
3) Anti-creep: approx. 2m
2) Influence of weather reduces the lifetime of
the unit. Please take care to mount correctly.
16 m
LED Functional display
Slow flashing: EEPROM empty
Fast flashing: EEPROM is written
During the self-testing cycle, the LUXOMAT
280 will only react to commands “RESET” and
“LIGHT OFF”
Follow-up time
Test operation, 15sec. ... 16min., Pulse operation
(Test operation: range testing, detector switches
on/off the lighting at any recognized movement)
Lux value
Night operation...Dusk...Day operation
(Day operation: light sensor inactive, switching at
any brightness value)
2,50 m
®
LC-plus
280°
16 m
280°
20 m
3
> 1m
4
3) Minimum distance to switched lighting,
frontally or laterally to device: 1m
4) Never mount the connected lights below the
motion detector!
6. Factory settings
& “TEST”
On delivery the potentiometers are adjusted in
position “TEST” and “SUN” symbol (daytime
operation). With this adjustments the following
regular values are active:
Follow-up accommodation: 3min.
Lux value: approx. 20Lux
Reset: The adjusting into “Factory settings” from
any other position causes a “Reset” of the device.
That means all parameters are resetted into factory
settings (fast LED-flashing).
9. Exclude sources of interference
2
60˚
1) Blind for limiting creep-under protection
2 m
16 m
and backward detection
9 m
2) Blinds for reduction of far-away and
close-by areas by 60° each
3) Blinds for reduction of far-away areas by
60° each
11. Settings of remote control
1
LUXOMAT® IR-LC-plus
LUXOMAT® IR-LC-plus (accessory, see point 20)
1)
2)
LUXOMAT® IR-LCmini (accessory, see point 20)
Caution: Settings with remote control subscribe
the settings by courtesy of potentiometers (see
point 5) (for description see point 12).
IR-LCmini
PARTY
LUXOMAT
IR-RC mini
3
1
RESET
®
2
12. Functions of LUXOMAT®
L
N L’
12
IR-LC-plus
Unlocking device
Lux value: Day operation
light sensor inactive, switching
at any brightness value
Lux value: approx. 100Lux
Onset of dusk
Lux value: approx. 25Lux
Advanced dusk
Lux value: approx. 2 Lux
Darkness
Automatic reading in the
current light value
Individual light value
2 - 2500Lux
Follow-up time
15sec. up to 16min.
Impulsfunction
1sec. ON, 9 sec. OFF
Walk test
Switching ON/OFF
Alarm function
Switching ON/OFF,
(ON for 30sec., OFF for
1sec., then normal operation)
Vacation- and comfort function
Switching ON/OFF
On: By achieving the Lux value
1 hour daylight independent
of movements, then normal
operation (switching time
changeable, see point 15)
Sensitivity adjustment
~ +15%, ~ – 30 %
Reset
Erasing of all of the values set
using the remote control. (Then
potentiometer-settings active,
see point 5)
Lock device (by pressing the button
shortly)
Double lock devise (sabotage
protection)
Keep the button pressed while LEDs
flash. As soon as the LEDs are on
permanently, the double-locking is
active.
Test operation
Switches the light ON/OFF when
movement is detected.
Light ON for 12h2) / Light OFF for 12h
By pressing once the party button, the
light is switched on for a period of 12
hours. By pressing the party button twice,
the light remains switched off until the
next evening (see point 14).
Light OFF
Switches the light ON again when
movement is detected.
Reset
Light OFF, then automatic mode
1)
14
IR-LCmini
Test operation
Switches the light ON/OFF when
movement is detected.
Light ON for 12h / Light OFF for 12 h
PARTY
By pressing once the party button, the
light is switched on for a period of 12
hours. By pressing the party button
twice, the light remains switched off
until the next evening (see point 14).
Light OFF
Switches the light ON again when
movement is detected.
Vacation- and comfort function
COMFORT
Switching ON/OFF
On: By achieving the Lux value 1 hour
daylight independent of movements,
then normal operation (switching time
changeable, see point 15)
Reset
Light OFF, then automatic mode
14. Activation “Light OFF”
Because of the sabotage protection the function
“Light off” is deactivated in the factory. When
required it must be activated again:
1. Mains to be disconnected
2.
Mains to be connected - a self test cycle
of 60sec. starts (the LED is flashing, see
point 5).
3.
Activation/deactivation of the function “Light
Off” can be done only during the self testing
cycle
For a
ctivation of the function “Light OFF”
the button “Light OFF” must be pressed
during the self testing cycle (the LED will
flash quickly).
For deactivation “Light OFF” the button
“Reset” must be pressed during the self
testing cycle (the LED will flash slowly).
Caution: The implementation of “Reset” with potentiometers (see point 6) or with remote control
(see point 12) does not influence the activation/
deactivation of the function “Light OFF”
15. Vacation- and comfort function
The duration of the on-period can be adjusted:
1. “Unlock” unit with remote control
2. The button “Co“ to be operated. The LED
flashes for 10sec.
3. During these 10 seconds the duration of the
light-on period can be selected: from e.g.
15sec. = 15min. up to 16min. = 16hrs.
4. The unit to be locked with the button “Lock”.
5. “Vacancy/Comfort” is activ now (deactivation see point 12)
Caution: If the “Vacation- and comfort function”
is active or with lower deviation of the Lux value
the LC-plus turns on the light again after a time
delay of 60sec.
Standard operation
(with optional arc extinctions kit)
Optional extension for switching of parallel
inductors, rocker switches, fluorescent lamps etc.
N L’
RC
N L’
L
N L’
L
Terminal connection for parallel operation
We recommend max. 5 motion detectors.
N L’
L
Permanent light operation with external push
button
Additionally manuel switching is possible. The
NC-contact is to press for approx. 0.5 - 2 sec.
L
Permanent light operation with external switch
Switching is manually possible (permanent light
operation). Caution: Light has to switched off
manually.
17. Dimensions (mm)
78
68 42
L N L'
18. Technical data16. Wiring diagrams13. Functions of LUXOMAT®
Power supply: 230V~ ±10 %
Switching power: 2000 W, cosϕ = 1
Range: approx. 16m
Time settings: Impuls, 15sec. - 16min.
Photo electric switch: approx. 2 - 2500Lux
Factory settings: follow-up accommodation
Detection area: 280°, 360° anti-creep
Degree of protection/class:
IP44 / II
Dimensions: L 110 x W 68 x H 78mm
Material:
Mounting types: wall and outside corner
Inserting of the connection cable:
once from top down and
Range adjustment:
> Swivelling of the sensor head: vertically
(approx. ±15°), horizontally (approx. ±45°)
> With blank out clips (included)
Electrical adjustments: in traditional manner
with potentiometers valid for time and Lux value
only, with infrared remote control.
1000VA, cosϕ = 0.5
3 min., photo electric
switch approx. 20Lux
protection
UV-stabilised Polycarbonate
mountable with included
plug-in socket
from below
19. Article / Part nr. / Accessory
®
LUXOMAT
LC-plus 280 white: 91008
brown: 91018
black: 91028
silver: 91048
LUXOMAT
IR-LC-plus (incl. wall bracket) 92095
IR-LCmini 92093
Accessory:
Arc extinction kit 10880
Motion detector:
®
Remote control:
1)
As soon as the function “Chime /
Impulse” is activated, the following
functions will be blocked: Alarm
function, Light ON for 12hrs / Light
OFF for 12 hrs, Vacation- and comfort
function
2)
Light ON for 12 h can also be activated
by disconnection mains twice within
2 - 4 sec.
49.5 13
528 8
MAN 5884– 230714 – 2
Loading...