Bebesounds MO141, MO142 Instruction Manual
Easy-to-Hold
Sound Monitor
with Sound Lights
Instruction Manual
Manual de Instrucciones
Model #MO141 & #MO142
49MHz-Manual 10/17/05 11:25 AM Page 1
All manuals and user guides at all-guides.com
all-guides.com
CONTENTS
Introduction........... . .2
Instructions for Use.......4
Using Voice Activation......6
Safety Instructions. . . . . . . . 7
Product Care. ...........7
Troubleshooting. . . . ......8
Technical Specifications.....9
Warranty Information.....10
Also Available...........11
INTRODUCTION
Thank you for purchasing our BébéSounds
®
Easy-to-Hold Sound Monitor. With this monitor
you will be able to hear your child while you
move freely around the house. It features superior
sound clarity and range with 49 MHz technology, and
the 2 channels help you maximize reception and mini-
mize interference.
The transmitter’s built in microphone picks up your
baby’s sounds and sends them to the portable receiver.
The receiver also features “Sound Lights” on an LED
sound bar so you can “see” your baby’s sounds in case
background noise prevents you from hearing your baby.
Choose the channel that provides the best reception.
Both units can be operated on either AC or battery
power so you can easily move around the house while
your baby is sleeping. You also have the flexibility of
easily moving the transmitter if your baby is outside
the nursery.
Please read all the instructions carefully before
operating this monitor. Please save the manual,
including the important safety instructions, for
future reference.
WARNING: This monitor is not intended to replace
adult supervision of children.
2 3
NURSERY UNIT
PARENTS’ UNIT
Belt Clip
Belt Clip
Channel/
Power
Channel/
Power
Antenna
Voice
Activation
Power
Indicator
AC
Adapter
Jack
Battery
Cover
AC
Adapter
Jack
Antenna
Voice
Activation
Power
Indicator
LED
Sound
Lights
Battery
Cover
49MHz-Manual 10/17/05 11:25 AM Page 2
All manuals and user guides at all-guides.com
INSTRUCTIONS FOR USE
1. Select either AC or battery power (see below).
2.
Turn both units on making sure they are set to the same channel. To change the
channel,
slide the Channel/Power switch to either the A or B position on both units
(See Fig. 1).
3. Adjust the volume control on the Parents’ Unit.
4. Adjust the optional Voice Activation on the Nursery Unit (See Fig. 2). Activating
this feature may avoid the transmission of some background sounds that don’t
pertain to your baby. Adjust the sensitivity of the Voice Activation to your preference.
Using AC Power
1. Plug the AC adapter into the right side of each unit (See Fig. 3).
2. Plug the AC adapter into the outlet in your wall.
3. Use only the BébéSounds® adapters included with the monitor. Do not use these
adapters with any other equipment.
Using Battery Power
1. Using a very small Phillips head screwdriver, unscrew the cover of the battery
compartment and slide down and off (See Fig. 4).
2. Insert one 9-Volt battery by snapping it to the black tab inside the compartment.
3. Replace the cover and tighten the screw.
4. Replace the batteries every 6 months or as needed.
Note: It is recommended that you keep batteries in your monitor at all times in case of a
power outage.
54
Fig. 1 Fig. 2
Fig. 3 Fig. 4
49MHz-Manual 10/17/05 11:25 AM Page 4
All manuals and user guides at all-guides.com
IMPORTANT SAFETY INSTRUCTIONS
This device is designed to monitor only the sounds of your child. It will not alert you
to your child’s silent activities. This product is not designed or intended for use as a
medical device. Always be sure that both the transmitter and receiver are working
properly and are within range of each other. This monitor is not intended to replace adult
supervision of children.
1. Keep adapter cords and units out of the reach of children.
2. Do not use with extension cords.
3. Do not place the monitor inside the crib.
4. Use only with 110-Volt electrical outlets.
5. Allow for proper ventilation when in use.
6. Do not place the units in a drawer as this will interfere with the
transmission of sound.
7. Do not position monitor where it can get wet or near sources of heat
such as a radiator.
8. Do not immerse the monitor in water.
9. Place in a safe place and out of the reach of children.
10. Do not disassemble the units.
11. Use only 9-Volt batteries or the AC adapters provided.
PRODUCT CARE
Clean the exterior surface of the BébéSounds®Easy-to-Hold Sound Monitor with a soft dry
cloth. Do not use sprays or liquids of any kind. Never immerse in water.
USING VOICE ACTIVATION
Voice Activation eliminates the background “hum” associ-
ated with sound monitors when there is no significant
sound being transmitted from your baby’s room. It does
this by automatically placing both the Nursery Unit (transmitter)
and the Parents’ Unit (receiver) into a “standby” mode. When sig-
nificant sound is detected, the Voice Activation automatically
returns both units to an “active” mode and immediately transmits
your baby’s sounds to you.
You can determine how sensitive you want the Voice Activation
feature to be. For example, if you want to hear the slightest
sound in the nursery, adjust the sensitivity on the Voice Activation
dial on the Nursery Unit to the maximum level (See Fig. 5). If you
only want to hear when your baby cries, adjust the sensitivity to a
lower level. You may have to adjust the sensitivity level a couple
of times until you get the exact level you want.
Remember, when using the Voice Activation feature you may think
the sound monitor is not working because the monitor is com-
pletely quiet and you don’t hear a background “hum.” Don’t
worry – the monitor is in a “standby” mode and will immediately
return to the “active” mode when your baby cries or makes
sounds. If you want to hear this “hum,” deactivate the Voice
Activation by switching it off on the Nursery Unit (See Fig. 6). The
Voice Activation controls are only on the Nursery Unit, not on the
Parents’ Unit.
76
Fig. 5
Fig. 6
49MHz-Manual 10/17/05 11:25 AM Page 6
All manuals and user guides at all-guides.com
Loading...