B&C Technologies B-Computer Programming User Manual

Washer-Extractor

B-Computer Programming

and Operating Instructions

cY01

B&C Technologies

Panama City, FL

[phone]
[phone] FAX
www.bandctech.com

Revision 2.0
29-Sept-2008

Accurate Technologies

Samutprakarn, Thailand

[phone]

[phone] FAX

www.accuratethai.com

Table of Contents

Introduction

Customer Service
Replacement Parts

Safety Information

Key Symbols
Important Safety Information

Operation

Cycle Selection
Cycle Execution
Check Cycle

3
3

4
5

6
6
8

Programming

Key Functions
Setup Mode
Cycle Count
Cycle Programming
Cycle Segment Tables
Programming Worksheets
Factory Programs

9
10
10
10
12
15
16

B&C Technologies

Panama City, FL

[phone]
[phone] FAX
www.bandctech.com

Accurate Technologies

Samutprakarn, Thailand

[phone]

[phone] FAX

www.accuratethai.com

Introduction

B-Computer

The B-computer is a powerful and versatile
solid state control. Up to 30 programs can be
stored and executed. The computer comes
standard with several pre-programmed cycles,
which are discussed later in the manual (see
table of contents for locations).

Note: Do not power off the machine while the
mode switch is in Program position. Doing this
will result in program data corruption, requiring
a reprogramming of some or all of the cycles.
Always move the Program switch into the Run
position before powering down the equipment.

Keypad

The user interface for the B-computer control is
a four pushbutton keypad with an LED (Light
Emitting Diode) display. This interface is
located on the front of the machine. In Run
mode, the keys function as follows:

LED Display

cY01

Stop

Customer Service

Start

Cycle

Up

Cycle

Down

Used in cycle selection:

Pressing this key increments
the cycle up by one; during a
cycle, shows the temperature.

Pressing this key increments
the cycle down by one; during a
cycle, shows the temperature.

Used to stop a cycle in progress

Used to start a cycle; during a
cycle, displays the current
cycle.

For technical assistance, call the following
number:

In the United States
Phone: [phone]
FAX: [phone]
e-mail: [e-mail]
Web: www.bandctech.com

In Thailand
Phone: [phone]
FAX: [phone]
e-mail: [e-mail]
Web: www.accuratethai.com

Replacement Parts

In the event that literature or replacement parts
are required, contact the local distributor of the
equipment, or contact B&C Technologies at the
above phone numbers/internet addresses.

3

Anyone operation or servicing this machine must follow the safety rules in
this manual. Particular attention must be paid to the DANGER,
WARNING, and CAUTION blocks which appear throughout the manual

The lightening flash and arrowhead within the triangle is a

Key Symbols

warning sign alerting you of the presence of dangerous

The exclamation point within the triangle is a warning sign
alerting you of important instructions concerning the machine

This warning symbol alerts you to the presence of possible
dangerous drive mechanisms within the machine. Guards
should always be in place when the machine is in operation.

This warning symbol indicates the presence of possibly
dangerous chemicals. Proper precautions should be taken
when handling corrosive or caustic material.

This warning symbol indicates the presence of hot surfaces
that could cause serious burns. Stainless steel and steam lines
can become extremely hot and should not be touched.

This warning symbol indicates the presence of possible
dangerous pinch-points. Moving mechanical parts can crush
an/or sever body parts.

Before servicing any equipment, make certain it is
disconnected from the electrical power source. Never allow
operation of the machine when any safety device is
malfunctioning. Never bypass safety devices.

.

4

Important Safety Information

SAFETY CHECK LIST

Before Initial start up of a washer – extractor
perform the following safety check:

A. Make sure all electrical and

plumbing connections have been

made in accordance with

applicable codes and regulations.

B. Make sure the machine is

grounded electrically.

C. Make sure the machine has

flexible water fill and drain

connections of the correct size,

length and type, with no kinks,

and that they are securely

attached and/or clamped.

D. Make sure the transport brackets

have been removed (if

applicable).

Before machine is placed in operation, the door
safety interlock must be checked for proper
operation as follows:

A. When the washer is energized

electrically and in operation, the
loading door must be locked in
the closed position. Verify this by
attempting to open the loading
door when the machine is
operating. If necessary, check the
door safety interlock and sensors
for proper operation. Consult
the service manual, or call a
qualified service technician if
necessary.

B. When the washers loading door

is open, it should not be possible
to start the machine. Verify this
by attempting to start the washer
with the door open. Also, close
the door without locking it
and verify that it is not possible to
start the machine with the door
not locked. If necessary, check
the door lock sensors for proper
operation. Consult the service
manual, or call a qualified
service technician. If additional
information is required, contact
your local distributor or call the
manufacturer of the machine.

Before servicing any equipment, make certain it
is disconnected from the electrical power
source. Never allow operation of the machine
when any safety device is malfunctioning.
Never bypass safety devices.

5

Display Meaning Display Meaning

S04

ROM code. Example only.

FLUS

Overflow prewash selected

Hold

Wait - machine just powered up

CFIL

Cold Fill

CY

Cycle number (followed by 2 digits)

Bfil

Warm Fill (both hot and cold)

CHEC / CYC

Test Cycle

hfil

Hot Fill

Far

Degrees Farenheit

lole

Low water level

CEL

Degrees Celcius

hile

High water level

PrE

Prewash segment (1st of 8 segments)

sup1

Supply 1

UASH

Wash segment (2nd of 8 segments)

sup2

Supply 2

FIL1

First rinse (3rd of 8 segments)

sup3

Supply 3

FIL2

Second Rinse (4th of 8 segments)

sup4

Supply 4

FIL3

Third Rinse (5th of 8 segments)

sup5

Supply 5 (Supply 1 & 2)

FIL4

Fourth Rinse (6th of 8 segments)

sup6

Supply 6 (Supply 2 & 3)

FIL5

Fifth Rinse (7th of 8 segments)

sup7

Supply 7 (Supply 3 & 4)

FIL6

Sixth Rinse (8th of 8 segments)

stop

Stop Routine

SRIN

Spray Rinse

sdly

Spin coast down delay

DRIN

Dilution Rinse

done

Cycle complete, open the door

PrEU

Normal Prewash selected

door

Door not closed and locked

SPIn / rInE

Reads "spin" for one second, then "time"
followed by the spin time

fill / stop

Programmed water level not reached
after 30 minutes

Tsfl

Temperature sensor failure or
temperature out of range.

full

Water level is detected when none
should be present. Can indicate a
clogged drain.

Operation

Cycle Selection

Press the up or down key until the desired cycle
number is showing on the display. Press the
keys just hard enough to activate them.
Pressing harder will cause undue wear on the
keypad. After you arrive at the desired cycle,
ensure the goods are loaded, and the door is
closed. Then press Start. If the door is not
properly closed and locked, the display will
read Door until the door is properly closed and
locked. After the door is closed, press start.

Cycle Execution

A cycle can be aborted at any time by pressing
the stop key. The machine will enter the stop
routine after which the door may be unlocked
(display reads done).

To display the temperature of the wash solution
during a cycle, press the up key. To display the
cycle number currently in process, press the
start key.

Display Indications

The following table lists the displays the B-compter is capable of and their meanings. Familiarize
yourself with these displays and their meanings.

6

Operation

Cycle Execution (continued)

Each of the 30 cycles consists of 8 segments. A
typical cycle has Prewash, Wash, and Rinses
(up to six are available). Upon the completion
of the last rinse, a final spin occurs. Following
is a description of each cycle segment.

Fill

After the start key is pressed, the drain is closed
and the machine begins filling to the
appropriate water level. Each wash segment
begins with a fill. After the water level is
reached, the cycle time begins to count down
(the cycle timer is paused during fill, heat and
drain steps). If a supply is programmed during
the segment, the dispenser will be flushed
during the fill.

If the machine is connected to an external
chemical supply system, the programmed
supply will begin 10 seconds into the fill. The
supply remains on until the programmed water
level is reached, or sixty seconds have elapsed.
If the water level is not reached after 30
minutes, the display will flash Stop and Fill.
The onboard beeper will also sound for 10
seconds. The machine will then enter the stop
routine.

Gentle Wash

Cycles 8, 16, and 24 use a gentle agitation
profile. This profile is used in the prewash,
wash, and rinse steps. The gentle wash
agitation profile is:

> 3 seconds counterclockwise at wash

speed

> 12 second pause
> 3 seconds clockwise at wash speed
> 12 second pause

Heat

If a wash segment contains a heat step, the
heating elements will begin to heat the wash
solution after the programmed level has been
reached. If the water does not reach the
desired temperature after 30 minutes, the
machine will progress to the next step.

Drain

At the conclusion of a prewash, wash, or rinse
segment, the drain valve opens and the wash
cylinder turns clockwise at wash speed. The
machine should drain in less than 30 seconds.
If draining takes longer than this, a clogged
drain hose is usually to blame. Contact a
qualified service technician.

Wash

Standard Wash

As soon as the programmed water level is
reached (and any programmed temperature is
reached) the display begins to count down the
remaining time left in the cycle.

All except three cycles use the standard
agitation profile. This agitation profile is active
during prewash, wash, and rinses. The
standard sequence is:

> 12 seconds counterclockwise at wash

speed

> 3 second pause
> 12 seconds clockwise at wash speed
> 3 second pause

After the water level has fallen below the low
level, there is a fifteen second delay, during
which the computer monitors the water level. If
water is sensed, the computer waits until both
high and low level inputs show that there is no
water in the wash cylinder. Assuming no water
is detected, the drain sequence concludes, and
the computer proceeds to the next segment.

Spin

After the drain sequence, the machine
progresses to spin speed if the spin time is not
zero. The displayed time will continue counting
down. After the programmed spin time has
elapsed, the next segment of the wash cycle
begins or the stop routine begins, if the spin
was the final spin of the wash cycle.

7

Operation

Cycle Execution (continued)

Stop Routine

When the final spin of the wash cycle is
complete, the stop routine is activated. The
stop routine sequence looks like this:

> All inputs are turned off
> A forty second coast down timer is

activated (after a spin)

> 12 seconds clockwise at wash (if no

spin)

> 3 seconds pause (if no spin)
> 12 seconds counterclockwise at wash
> 5 second pause
> The display shows done

Once the display shows done, the door can be
opened. Once the door is opened, the display
reverts to the cycle number of the cycle just
completed. The machine is now ready to run
another wash program.

WARNING

Never insert any part of your
body or any object into the
wash cylinder until it has
completely stopped. Doing so
could result in serious injury.

Note: if the display shows done and the wash
cylinder continues to rotate for an abnormally
long time, this means that the water failed to
completely drain, or the water level switch is
faulty. The door will not unlock until the
problem is corrected.

seconds, then reverse for 12 seconds. Failure to
advance beyond this point indicates no water
coming into the machine, water not staying in
the machine, water level switch failure, water
level hose failure, or debris blocking the water
level tube in the sump of the machine.

sup1 - the supply 1 signal appears at the

rear of the machine, flush cup 1 fills with water.

sup2 - the supply 2 signal appears at the

rear of the machine, flush cup 2 fills with water.

sup3 - the supply 3 signal appears at the

rear of the machine, flush cup 3 fills with water.

sup4 - the supply 4 signal appears at the

rear of the machine, flush cup 4 fills with water.
Failure of the signal to appear and failure to
flush any water indicates a blown 500mA fuse
on the output board located inside control
panel.

hile - both fill valves begin filling the

machine to high water level. Failure to advance
beyond this point indicates water not staying in
the machine, water level switch failure, water
level hose failure, or debris blocking the water
level tube in the sump of the machine.

dran - drain valve opens and allows

water to drain from the machine. Failure to
advance beyond this point indicates a clogged
drain system, or a bad water level switch
system.

spin - machine ramps into a short spin

routine.

Check Cycle

The B-Computer has a built in diagnostic check
cycle which is very useful for troubleshooting.
To access the check cycle, press the down
arrow when the display shows cy01. The
display will then alternate between check and

cycle. Press the start key to begin.

lole - both fill valves begin filling the

machine to low water level while the cylinder
rotates forward for 12 seconds, pause for 3

8

Programming

The computer board is located inside the
control module. In the middle of the board is a
small toggle switch used to change from Run
mode to Program mode (see illustration).

WARNING!

Dangerous voltages can be
present inside the control
module. Only qualified
service technicians with

specific knowledge of test
procedures and safety precautions should
attempt troubleshooting and repair. Disconnect
power before removing panels and covers, and
before attempting service procedures.

The Run/Program switch is normally in the Run
mode position. To enter program mode, flip
the switch to the opposite position (Program
mode). The display changes to show the
current temperature in the wash cylinder,
indicating that the control is in program mode.
See the next section for key functions while in
program mode.

370555 20

Key Functions in Program Mode

The Up key is used to increase
cycle numbers and other
numerical values, like time and
temperature, when creating wash
formulae.
The Down key is used to
decrease cycle numbers and
other numerical values, like time
and temperature, when creating
wash formulae.

The Stop key saves all data and
terminates the programming
procedure. If you press this key
first when entering program
mode, the computer will enter
Setup. If the stop key is pressed
again, you will exit
Setup mode and return to
Program mode.

The Start key is the Enter
command while in Program
mode. Pressing this key enters
the data, and moves to the next
programming function in the
cycle.

MADE IN USA

J1

J2

MMATS

J3

FLIP SWITCH
FOR PROGRAM
MODE

9

Programming

Segment Display Segment Display

Prewash PRE Fill 3 FIL3

Wash UASH Fill 4 FIL4

Fill 1 FIL1 Fill 5 FIL5
Fill 2 FIL2 Fill 6 FIL6

Cycle Segments

Setup Mode

The setup options are programmable options
that are in operation during all wash cycles.
The options are:

> Temperature displayed in degrees

Celsius or Fahrenheit.

> Spray Rinse and Supply 4 enabled
> Auxiliary heat and Spray Rinse enabled
> Auxiliary heat and Supply 4 enabled

Take note that these options can only be
changed while in Setup mode.

Temperature Display

This setup option affects the display and
programming of all temperatures. CEL selects
programming/display in degrees Celsius, while
FAR selects degrees Fahrenheit. The Up and
Down keys toggle between the two settings.
The Start key accepts the selection and moves
you to the next setup option.

further Setup programming is possible. Press
the Stop key to exit Setup.

To enable Auxiliary Heat and Supply 4, press
the Up or Down key to see HEAT. Press the
start key (enter). Now press the Up or Down
key to see SUP4. Press the Start key to select,
and press the Stop key to save and exit Setup
mode. This is the default mode for machines
without Spray Rinse.

Cycle Count

To display the current cycle count, press the
Start key after entering Program mode (the
display will show the current temperature in the
wash cylinder). The display will show a 2 digit
number indicating how many cycles have been
completed (cycles interrupted are not counted).
Press the Start key again to return to program
mode without resetting the count. Press the Up
or Down key to reset the count to zero and
return to program mode.

Spray Rinse, Supply 4, and Auxiliary
Heating

This setup option allows you to select among
the following options:

> Spray Rinse and Supply 4 enabled
> Auxiliary heat and Spray Rinse enabled
> Auxiliary heat and Supply 4 enabled

To enable Spray Rinse and Supply 4, use the
up and down key to see SRIN. When this
option is selected, Spray Rinse and Supply 4
are enabled, as well as Supply 7 (Supply 3 and
Supply 4 combined). This is the default setting.
When this option is selected, no further
programming in Setup is possible. Press the
Stop key to exit Setup.

To enable Spray Rinse and Auxiliary Heating,
use the up or down key to see HEAT instead of
SRIN, as above. Now press the Start key
(enter). Now use the up or down key to see
SRIN. Press the start key (enter). No

Cycle Programming

To edit an existing cycle, or create a new one,
press the Up key while the wash cylinder
temperature is displayed. The display will
change to show CY01. Press the up or down
key until the cycle number you wish to
change/create is displayed. Now press the Start
key to begin editing your cycle. Please note
that the test cycle cannot be displayed or
altered.

All programmed cycles follow a certain routine,
consisting of eight program segments, displayed
in the table below.

10

Programming

Func tion Minimum Maxim um
Prewash 2 minutes 30 minutes
Wash 2 minutes 20 minutes
Fill 1 2 minutes 15 minutes
Fill 2 2 minutes 15 minutes
Fill 3 2 minutes 15 minutes
Fill 4 2 minutes 15 minutes
Fill 5 2 minutes 15 minutes
Fill 6 2 minutes 15 minutes
Intermediate Spin 30 seconds 120 seconds
Final Spin 1 minute 10 minutes

Temperature

75F / 25C

200F / 93C

Time and Tem perature Paramet ers

Display Fill Type

HFIL Hot Fill
CFIL Cold Fill
BFIL Warm Fill

Fill Temperature Opt ions

Display Fill Level

LOLE Low Level
HILE High Level

Fill Level O ptions

Display Supply

SUP0 No Supply
SUP1 Supply 1
SUP2 Supply 2
SUP3 Supply 3
SUP4 Supply 4
SUP5 Supply 1 & 2
SUP6 Supply 2 & 3
SUP7 Suppply 3 &4

Suppl y O pt ions

Supply 4 & 7 are only
avaliable if is Supply 4 was
enabled in Setup

Cycle Programming (continued)

When modifying a cycle time, a time must be
entered for each segment. To skip a segment or
spin, enter 00 for the time and press the Start
key. The following table shows the range of
time allowed for each segment and spins, as
well as the allowed temperature range for
machines equipped with auxiliary heat.

Use the Up and Down keys to select the fill
temperature. The following table shows the
available options.

After you have selected the appropriate fill
temperature, press the Start key.

Now you can select the Fill level by using the
Up or Down key. Select your fill level
according to the following table.

Note that spin times are programmed in
seconds for intermediate spins following
Prewash, Wash, and Fills 1 through 5. The
final spin, following Fill 6 is programmed in
minutes.

To begin programming, press the Up key shows
the segment to be edited, then press the Start
key.

For the Prewash segment, you can select either
PREU (normal Prewash) or FLUS (overflow fill
Prewash). If Overflow Prewash is selected, the
fill valves will remain on for the duration of the
Prewash step. Press the Start key to make your
selection.

If the Spray Rinse option is enable in Setup,
you have the option of Spray Rinse or Dilution
Rinse during Fill 1 through Fill 5. The display
shows SRIN for spray rinse or dRIN for dilution
rinse.

Note that if you selected FLUS for the Prewash
segment, this selection is skipped. After your
Fill level selection, press the Start Key.

Next select the desired Supply option. See the
table.

11

Programming

Details

Use Up or Down to change. Start key is enter or advance

PRE or FLUS Select Regular prewash or Flush
00 or 02 - 30 Segment time: 00 to skip, or any time between 0 and 30 minutes
HFIL CFIL BFIL Fill temperature: Hot, Cold, or Warm (both fill)
SUP0 - SUP7 Select Supply 0-7 (0 for no supply during the step)
00, 75 - 200
00, 25 - 93
SPIN flases for 1 sec
TIME flases for 1 sec

00 or 30 - 120

Select time for spin: 30 - 120 seconds. 00 for no spin.

Note: Supply 4 and 7 are only availble if enabled in Setup
Note: Heat is only available if enabled in Setup

Prewash Segment

Display

PRE

Enter temperature: 75-200 deg F, 25-93 deg C. 00 for no heat.

Select 00 if you have programmed a Flushing Prewash

Cycle Programming (continued)

After selecting your desired supply option, press
the Start key.

If your machine is equipped with Auxiliary
heating, and it was enabled during Setup
programming, you may use the up or down key
to select the target temperature for the segment.
To disable Auxiliary heat for the segment, set
the value to zero.

NOTE

NOTE

If the machine does not have auxiliary

If the machine does not have auxiliary

heating, do not program a temperature.

heating, do not program a temperature.

If you program a target temperature that

If you program a target temperature that

the machine is unable to achieve, the

the machine is unable to achieve, the

machine will try for 30 minutes during

machine will try for 30 minutes during

the segment. It is also important not to

the segment. It is also important not to

program heat during a prewash segment

program heat during a prewash segment

with a flush fill.

with a flush fill.

After you have set the spin time, press the Start
key, The display will now show the name of
the next program segment. See the chart on
page 10 for the list of program segments and
what the display indicates for each.

After you have selected the temperature, press
the Start key.

Now select the spin time for the segment. If
you wish to skip the spin, set the value to zero.

Cycle Segment Charts

12

Programming

Details

Use Up or Down to change. Start key is enter or advance

00 or 02 - 30 Segment time: 00 to skip, or any time between 0 and 30 minutes
HFIL CFIL BFIL Fill temperature: Hot, Cold, or Warm (both fill)
LOLE or HILE Select Fill level, Low or High
SUP0 - SUP7 Select Supply 0-7 (0 for no supply during the step)
00, 75 - 200
00, 25 - 93
SPIN flases for 1 sec
TIME flases for 1 sec

00 or 30 - 120

Select time for spin: 30 - 120 seconds. 00 for no spin.

Note: Supply 4 and 7 are only availble if enabled in Setup
Note: Heat is only available if enabled in Setup

Display

UASH

Enter temperature: 75-200 deg F, 25-93 deg C. 00 for no heat.

Select 00 if you have programmed a Flushing Prewash

Wash Segment

Details

Use Up or Down to change. Start key is enter or advance

drin or srin (1) Select Rinse Method: Dilution Rinse or Spray Rinse
00 or 02 - 30 (2) Segment time: 00 to skip, or any time between 0 and 30 min
HFIL CFIL BFIL (3) Fill temperature: Hot, Cold, or Warm (both fill)
LOLE or HILE (4) Select Fill level, Low or High
SUP0 - SUP7 (5) Select Supply 0-7 (0 for no supply during the step)
00, 75 - 200
00, 25 - 93
SPIN flases for 1 sec
TIME flases for 1 sec

00 or 30 - 120

(7) Select time for spin: 30 - 120 seconds. 00 for no spin.

Note: Heat is only available if enabled in Setup
Note: If Spray Rinse is selected for the segment, steps 3 to 6 are skipped.

fil1 fil2 fil3 fil4 fil5

(6) Enter temperature: 75-200 deg F, 25-93 deg C. 00 for no heat.
Select 00 if you have programmed a Flushing Prewash

Note: Supply 4 and 7 are only availble if enabled in Setup

Fill Segments (Fill 1 through Fill 5)

Display

Cycle Segment Charts (continued)

13

Programming

Details

Use Up or Down to change. Start key is enter or advance

00 or 02 - 30 S egm ent time: 00 to skip, or any time between 0 and 30 min
HFIL CFIL BFIL Fill tem perature: Hot, Cold, or Warm (both fill)
LOLE or HILE S elect Fill level, Low or High
SUP0 - SUP7 S elect S upply 0-7 (0 for no supply during the step)
00, 75 - 200
00, 25 - 93
SPIN flases for 1 s ec
TIME flas es for 1 s ec
02 - 10 Select time for spin: 2 to 10 minutes

Note: Heat is only available if enabled in S etup

Enter temperature: 75-200 deg F, 25-93 deg C. 00 for no heat.
Select 00 if you have progra m m ed a Flushing Prewash

Note: Supply 4 and 7 are only ava ilble if enabled in Setup

Fill 6 Segment

Display

fil6

Cycle Segment Charts (continued)

14

Programming

Blank Cycle Chart

Program Number

Segment Detail Segment Detail

Prewasy/Flush Spray/Dilution

Time (min) Time (min)

Water Temp Water Temp

Water Level Water Level

Supply Supply

Temp Temp

Spin (sec) Spin (sec)

Time (min) Spray/Dilution

Water Temp Time (min)

Water Level Water Temp

Supply Water Level

Temp Supply

Spin (sec) Temp

Spin (sec)

Spray/Dilution Spray/Dilution

Time (min) Time (min)

Water Temp Water Temp

Water Level Water Level

Supply Supply

Temp Temp

Spin (sec) Spin (sec)

Spray/Dilution Spray/Dilution

Time (min) Time (min)

Water Temp Water Temp

Water Level Water Level

Supply Supply

Temp Temp

Spin (sec) Final Spin (min)

Fill 6

Fill 3

Fill 4Wash

Fill 5

Prewash

Fill 1

Fill 2

15

Factory Programs

Program Number: 1

S e g m e n t D e t a il S e g m e n t D e t a il

Prewasy/Flush Spray/Dilution

Time (min) 05 Time (min) 00

Water Temp cfil Water Temp

Water Level hile Water Level

Supply sup1 Supply

Temp 00f Temp

Spin (sec) 0 Spin (sec)

Time (min) 08 Spray/Dilution

Water Temp cfil Time (min) 00

Water Level lole Water Tem p

Supply sup2 Wa ter Level

Temp 00f Supply

Spin (sec) 60 Temp

Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 00

Water Temp cfil Water Temp

Water Level hile Water Level

Supply sup0 Supply

Temp 00f Temp

Spin (sec) 60 Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 02

Water Temp cfil Water Temp cfil

Water Level hile Water Level hile

Supply sup0 Supply sup03

Temp 00f Temp 00f

Spin (sec) 60 Final Spin (min) 05

Cold Wash Normal

Fil l 6

Fil l 3

Fil l 4Wash

Fil l 5

P rew ash

Fil l 1

Fil l 2

16

Factory Programs

Program Number: 2

S e g m e n t D e t a il S eg m e n t D e t a il

Prewasy/Flush Spray/Dilution

Time (min) 05 Time (min) 00

Water Temp bfil Water Temp

Water Level hile Water Level

Supply sup1 Supply

Temp 00f Temp

Spin (sec) 0 Spin (sec)

Time (min) 08 Spray/Dilution

Water Temp bfil Time (min) 00

Water Level lole Water Tem p

Supply sup02 Water L evel

Temp 00f Supply

Spin (sec) 60 Temp

Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 00

Water Temp bfil Water Temp

Water Level hile Water Level

Supply sup02 Supply

Temp 00f Temp

Spin (sec) 60 Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 02

Water Temp cfil Water Temp cfil

Water Level hile Water Level hile

Supply sup0 Supply sup3

Temp 00f Temp 00f

Spin (sec) 60 Final Spin (min) 05

Warm W ash Normal

Fil l 6

Fil l 3

Fil l 4Wash

Fil l 5

P rew ash

Fil l 1

Fil l 2

17

Factory Programs

Program Number: 3

S e g m e n t D e t a il S eg m e n t D e t a il

Prewasy/Flush Spray/Dilution

Time (min) 05 Time (min) 00

Water Temp hfil Water Temp

Water Level hile Water Level

Supply sup1 Supply

Temp 00f Temp

Spin (sec) 0 Spin (sec)

Time (min) 08 Spray/Dilution

Water Temp hfil Time (min) 00

Water Level lolw Water Tem p

Supply sup2 Water Level

Temp 00f Supply

Spin (sec) 60 Temp

Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 00

Water Temp bfil Water Temp

Water Level hile Water Level

Supply sup0 Supply

Temp 00f Temp

Spin (sec) 60 Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 02

Water Temp cfil Water Temp bfil

Water Level hile Water Level hile

Supply sup0 Supply sup3

Temp 00f Temp 00f

Spin (sec) 60 Final Spin (min) 05

Hot W ash Norm al

Fil l 6

Fil l 3

Fil l 4Wash

Fil l 5

P rew ash

Fil l 1

Fil l 2

18

Factory Programs

Program Number: 6

S e g m e n t D e t a il S eg m e n t D e t a il

Prewasy/Flush Spray/Dilution

Time (min) 00 Time (min) 00

Water Temp Water Temp

Water Level Water Level

Supply S upply

Temp Temp

Spin (sec) Spin (sec)

Time (min) 00 Spray/Dilution

Water Temp Tim e (m in) 00

Water Level W ater Temp

Supply Water L evel

Temp S upply

Spin (sec) Temp

Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 00 Time (min) 00

Water Temp Water Temp

Water Level Water Level

Supply S upply

Temp Temp

Spin (sec) Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 00 Time (min) 02

Water Temp Water Temp cfil

Water Level Water Level hile

Supply S upply sup0

Temp Temp 00f

Spin (sec) Final Spin (min) 05

Rinse & Spin

Fil l 6

Fil l 3

Fil l 4Wash

Fil l 5

P rew ash

Fil l 1

Fil l 2

19

Factory Programs

Program Number: 7

S e g m e n t D e t a il S eg m e n t D e t a il

Prewasy/Flush Spray/Dilution

Time (min) 20 Time (min) 02

Water Temp hfil Water Temp bfil

Water Level lole Water Level hile

Supply sup4 Supply sup0

Temp 00f Temp 00f

Spin (sec) 60 Spin (sec) 60

Time (min) 02 Spray/Dilution

Water Temp hfil Time (min) 02

Water Level lole Water Tem p bfil

Supply sup0 Water Level hile

Temp 00f Supply sup0

Spin (sec) 60 Temp 00f

Spin (sec) 60

Spray/Dilution S pray/Dilution

Time (min) 02 Time (min) 00

Water Temp hfil Water Temp

Water Level lole Water Level

Supply sup0 Supply

Temp 00f Temp

Spin (sec) 60 Spin (sec)

Spray/Dilution S pray/Dilution

Time (min) 15 Time (min) 04

Water Temp hfil Water Temp bfil

Water Level lole Water Level hile

Supply sup1 Supply sup3

Temp 00f Temp 00f

Spin (sec) 60 Final Spin (min) 05

Reclaim

Fil l 6

Fil l 3

Fil l 4Wash

Fil l 5

P rew ash

Fil l 1

Fil l 2

20