Product Overview |
|
|
|
2 |
Set DIP Switches |
|
4-Wire RS-485 (full-duplex) |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
+ RS-422 = All DIP Switches OFF |
||||||||
|
|
|
|
|
|
|
|
DIP SWITCH POSITION |
|
+ RS-485 = DIP 1 ON; DIP 2, 3 and 4 OFF |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
Switch |
OFF (left) |
ON (right) |
|
|
4 Wire Set-up |
|||||||
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
TD Always Enabled |
TD Only Enabled During Data |
|
USOPTL4(-LS) or |
|
RS-422/485 |
|
|||||
|
|
|
|
|
|
|
|
(RS-422) |
Transmission (RS-485) |
|
USPTL4(-LS) |
|
|
|
|
|
||||
|
|
|
|
|
Serial |
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
TDA(-) |
|
|
|
RDA(-) |
|
|
|||||
|
|
|
|
|
|
|
RD Always Enabled |
RD Disabled During Data |
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
USB Port LED |
Connecter |
2 |
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
||||||||||||
(ECHO On) |
Transmission (ECHO Off) |
|
|
TDB(+) |
|
|
|
RDB(+) |
|
|
||||||||||
|
|
DIP Switches |
|
|
|
3 |
4-Wire Mode |
2-Wire Mode |
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
RDA(-) |
|
|
|
TDA(-) |
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
4-Wire Mode |
2-Wire Mode |
|
|
RDB(+) |
|
|
|
TDB(+) |
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GND |
|
|
|
GND |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Install Drivers
Use the included CD to install the converter’s drivers.
Warning: To prevent installation errors, do not plug in the hardware until you have already installed the drivers.
After connecting the device, you can check Device Manager to learn which COM port number was assigned (Control Panel/ System/Hardware/Device Manager/Ports LPT & COM).
You can re-assign COM numbers by clicking the Advanced Settings button on the Port Settings screen.
3 Wire the Converter
2-Wire RS-485 (half-duplex)
+ All DIP Switches = On
2 Wire Set-up
USOPTL4(-LS) or |
|
RS-485 |
||||
USPTL4(-LS) |
|
|
|
|
||
|
TDA(-) |
|
|
|
NEG(-) |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TDB(+) |
|
|
|
POS(+) |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
RDA(-) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RDB(+) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GND |
|
|
|
GND |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 Loopback Test (optional)
•Set DIP switches 1, 3, 4 to ON.
•Set DIP switch 2 to OFF.
•Use HyperTerminal or another terminal program to confirm passage of data through converter.
5 Check LEDs
When everything is installed and connected, the LEDs will blink to indicate that data traffic is passing through the converter