27427 BOSTIK COURT
TEMECULA, CA 92590
INSTALLATION INSTRUCTIONS
INS048
For any questions, email us:
tech@bbkperformance.com
1996 - 2004 FORD MUSTANG GT 4.6L 2V
1996 - 2004 FORD MUSTANG GT 4.6L 2V/ 5.4L F-250
1990 - 1995 FORD 4.6L 2V APPLICATIONS
1997 - 2003 4.6L /5.4L F-150/EXPEDITION MODELS
1996 - 2001 FORD MUSTANG COBRA
1999 - 2004 FORD LIGHTNING/HARLEY 5.4L S/C
POWER-PLUS SERIES®
THROTTLE BODY
Part # 1700 / Ford Mustang GT 4.6L 2V
Part # 1701 / Ford Mustang GT 4.6L 2V, 5.4L F-250
Part # 1703 / Ford 4.6L 2V Applications, 4.6L/5.4L F-150 - Expedition Models
Part # 1705,1711 / Ford Mustang Cobra
Part # 1755 / Ford Lightning/Harley 5.4L S/C
Special Tools required: Feeler Gauge.
Install Time: Approximately 45 minutes.
Difculty: Very easy.
IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.
BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.
WWW.BBKPERFORMANCE.COM
MADE IN U.S.A.
MADE IN U.S.A.
UPDATED LAST: January 2017
27427 BOSTIK COURT
TEMECULA, CA 92590
For any questions, email us:
tech@bbkperformance.com
FOLLOW THESE INSTRUCTIONS CAREFULLY TO ENSURE CORRECT FITMENT AND OPERATION
STEP 1
Disconnect the negative battery terminal.
STEP 2
Loosen the 2 hose clamps and remove the inlet air tube connecting the throttle
body and airbox. Disconnect the PCV, Idle Air Control (IAC) tube and Inlet Air
Temperature Sensor connector if applicable.
STEP 3
Disconnect the return spring from the linkage and unhook the throttle cable by
opening the throttle manually and slipping the cable from the cam groove. Dis-
connect the cruise control cable if applicable.
STEP 4
Disconnect the throttle position sensor. Remove the 4 bolts securing the throttle
body to the intake, then remove it from the vehicle.
STEP 6
Using the supplied screws and gaskets, install the new throttle body on to the
intake manifold and tighten.
STEP 7
Re-attach the throttle cable, TPS sensor connector, return springs and cruise
control cable if applicable.
STEP 8
Re-install the inlet tube between the airbox and throttle body. Be sure to re-
connect the PCV tube, idle air control tube and inlet air temperature sensor if
applicable.
STEP 9
Reconnect the negative battery terminal. Start the engine and run until it is at
operating temperature, then turn the engine off.
STEP 5
Remove the throttle position sensor from the stock throttle body. Install the throt-
tle position sensor on to the new BBK Throttle Body using the supplied screws.
FOR OPTIMUM PERFORMANCE:
Match the intake opening to the new throttle body size. Although this is not
mandatory, it will maximize intake ow.
On vehicles that do not require the large IAC porting hole between the throttle
body bores simply install the supplied pipe plug from the backside of the throttle
body, tighten very snug to prevent the plug from loosening.
MADE IN U.S.A.
IMPORTANT: All appropriate safety equipment and gear must be used during the installation of this or any BBK Performance products or any time you work on a vehicle.
BBK Performance Inc. accepts no responsibility for injuries or damage caused by or during the installation of this product.
WWW.BBKPERFORMANCE.COM
STEP 10
Turn the idle screw counter-clockwise until you can see between the screw and
the throttle linkage (.010” with a feeler gauge). Then turn clockwise exactly one
full turn. Double check all fasteners and clamps to ensure they are all secure.
UPDATED LAST: January 2017
Loading...