Baumer SXG User Manual
Product Specication
open wire
26
36
26
36
16 x M 3 dep th 6
UN C 1/ 4-20
52
52
26
36
72
26
36
26
36
16 x M3 de pth 6
UNC 1/4 -20
52
52
26
36
72
open wire
open wire
open wire
open wire
5
4
SXG cameras – Maximum Performance with Kodak sensors
Dual Gigabit Ethernet progressive scan CCD camera ▪
Compact and lightweight aluminium housing ▪
Power over Ethernet support ▪
Standard RJ45 connector ▪
GigE Vision ▪
TM
standard compliant
Excellent image quality at high image rates ▪
Resolutions of 1, 2, 4 or 8 megapixel ▪
Frame rates up to 120 fps ▪
Compact design (52 x 52 x 72 mm) ▪
Dimensions (11047091)
● SXG (C-Mount version)
Quick Start Guide
SXG cameras with Kodak sensors
Latest software version and technical
documentation are available at:
www.baumer.com/vision/login
Safety
Conformity:
CE, FCC Part 15 Class B, RoHS
FCC – Class B device
No t e : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
support.cameras@baumer.com · Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany 07/13. v1.3 11054358
Safety instructions
Notice
See User´s Guide for the complete safety instructions!
Protect the sensor from dirt and ▪
moisture.
Never open the camera housing. ▪
Avoid camera contamination by ▪
foreign objects.
Environmental requirements:
Storage temp. -10°C ... +70°C
Operating temp. +5°C ... +60°C
Housing temp. max. +60°C
Humidity 10 % ... 90 %
non condensing
Camera Type
Monochrome
SXG10 1/2" 1024 x 1024 120
SXG20 2/3" 1600 x 1200 68
SXG21 2/3” 1920 x 1080 64
SXG40 1” 2336 x 1752 32
SXG80 4/3” 3296 x 2472 16
Color
SXG10c 1/2” 1024 x 1024 120
SXG20c 2/3” 1600 x 1200 68
SXG21c 2/3” 1920 x 1080 64
SXG40c 1” 2336 x 1752 32
SXG80c 4/3” 3296 x 2472 16
Sensor
Size
Resolution
Installation
Installation sample without PoE
1 - network interface card
2 - network cable
3 - Process interface cable
4 - Power cable
Installation sample with PoE via NIC
1 - PoE network interface card (NIC)
2 - network cable
3 - Process interface cable
Installation sample with PoE via Injector
1 - network interface card (NIC)
2 - network cable
3 - Injector
4 - network cable
5 - Process interface cable
Notice
Operation with a single GigE link is
possible as well.
Full Frames
[max. fps]
Dimensions (11047092)
● SXG-F (F-Mount version)
LED2
LED1
81
LED2
LED1
81
1
4
3
8
5
7
3
1
4
2
6
1
2
3
T T
General Description
1
2
3
4
56
LED Signaling
Heat Transmission
Caution
Provide adequate dissipation of heat, to ensure that the temperature
does not exceed +60°C (+140°F).
The surface of the camera may be hot during operation and immediately
after use. Be careful when handling the camera and avoid contact over a
longer period.
As there are numerous possibilities for installa-
tion, a specic method for proper heat dissipation
is not dened, but the following principles are
suggested:
Nr. Description Nr. Description
1 (respective) lens mount 4 Digial-IO supply
2 Power Supply 5 Data Port 1
3 Data Port 0 6 Signaling-LED
Data Interfaces
Data / Control
1000 Base-T (Port 0)
1 (gn/wh) MX1+ 1 (gn/wh) MX1+
2 (gn) MX1- 2 (gn) MX13 (og/wh) MX2+ 3 (og/wh) MX2+
4 (bu) MX3+ 4 (bu) MX3+
5 (bu/wh) MX3- 5 (bu/wh) MX36 (og) MX2- 6 (og) MX27 (bn/wh) MX4+ 7 (bn/wh) MX4+
8 (bn) MX4- 8 (bn) MX4-
Data / Control
1000 Base-T (Port 0)
Notice
Both data ports supports Power over Ethernet (38 VDC .. 57 VDC).Both ports can
be connected to a PoE power sourcing equipment however only one port will be
used to power the camera.
For the data transfer, the ports are equal. For Single GigE connect one port and
for Dual GigE connect the second Port additionally. The order does not matter.
LED Signal Meaning
1
2
3
green
green ash
yellow Transmitting
green
qellow
Power Supply and Process Interface
Power Supply Digital I/O-Supply
M8 / 8 pins
1 (bn) Power V
3 (bu) GND 2 (bn) Line 1
4 (bk) not used 3 (gn) Line 0
CC
1 (wh) Line 5
4 (ye) GND
5 (gr) U
6 (pk) Line 3
7 (bu) Line 4
8 (rd) Line 2
Power Supply
Power VCC 20 VDC .. 30 VDC
Link active
Receiving
Power On
Readout active
ex
T: Housing temperature
measurement point
Operate the cameras only in mounted condition ▪
with a good heat conductor (e.g. aluminum)
Mounting in combination with forced convection ▪
may provide proper heat dissipation
Loading...